REPLACE WITH USE CABLE WITH BATTERY CLIPS 15 MEG 200W R25 (CURRENT-LIMITING TO JUMPER B- SUPPLY TO FLOATING NICHROME COIL RESISTOR 75 DECK CHASSIS 24kW RESISTOR) REMOVE 150kV BUSHING BEAM VOLTAGE FROM FROM CB21 FROM CB22 CAPACITOR BANK B- BUS (DWG 430-106, P3) (DWG 430-106, P3) HV METERING TOWER HV COMPONENTRY BETWEEN CORONA RINGS ON TOP OF CAP. BANK INSIDE MODULATOR TANK L9 T23 AUX 3.4 uH T25 AUX LOWER CORONA RING MODULATOR 120V @ 6.9A 120V @ 6.9A -55kV FROM TAP ON RECTIFIER STACK * (DWG. 430_112) T23 T25 R86 ISO. 110kVDC -110kV FROM RECTIFIER STACK* 10K 4kW R84 * SEE DWG 430BLOK2.ECW CW C87: 11.4uF 8.6V @ 100A 8.6V @ 100A S76/1 100 FLOATING DECK OPTICAL FIBER PULSE 10kV UPPER400W CORONA RING T24 T28 BUFFER DECK OPTICAL FIBER 32V @ 25A NC NC 32V @ 25A R52 100k 800W 120VAC FROM K48B E18 V25 (4 x 100k IN (DWG. 430_106, p4) V25 15KV KLYSTRON B SERIES/PARALLEL) KLYSTRON A R4 LITTON L3403 25 120VAC FROM K48C LITTON L3403 300 M, 300W 200W R53 R47 (DWG. 430_106, p4) (R48,49,50,& 51) 10M 1k 200W C36 DISCONNECT 0.7 uF 55kV MODULATOR OVERCURRENT EARTH EARTH LATCHING RELAY GROUND GROUND ZENER TOWER K80 "KLY B COLLECTOR CURRENT" TO CONSOLE SCOPE CR5-CR9 C37-C41 R55 RG17u ANODE WIRES RUN CR9-CR13 C42-C46 150M 75 kV ACROSS FLOOR TO KLYSTRON VAULT TO KLYSTRON CR14-CR18 C47-C51 TO "BEAM VOLTAGE" SET COIL 100W BUSHING CATHODE (VIA R25), CR19-CR23 C52-C56 CONSOLE METER PROTECTION CIRCUIT - SHORTING BARS CROWBAR, CR24-CR29 C57-C61 RESET COIL R11 BODY CURRENT R22,R23 & HV METERING 0.16 METER SHUNT TOWER CR30-CR34 C62-C66 EACH 22k, 2W C88 R85 126W RG62 TO CONSOLE SCOPE SHORTING BARS CR34-CR39 C67-C71 E17 22K E13 1uF 2W R18 C28 C28/1 C29/1 1.5KV CR40-CR44 C72-C76 1uF 1uF .01uF R19 R93 100V 2.5 400V 4kV 600V CAPACITOR BANK CR45-CR49 C77-C81 400K 480W TO "KLY B COLLECTOR BLEEDER TOWER CR50-CR54 K80 CURRENT" 800W B- BUS (FULL HIGH VOLTAGE) C82-C86 R20 TO CROWBAR R21 TO MODULATOR VOLTMETER CONSOLE METER 50 CAPS FROM K57 (RESET) 5mV @ 5A PART B 50 ZENERS DWG J349C106 0.1uF, 600V EACH 50M 200Z K40A K39A R38 3.2M R1-1 R1-2 R1-3 R1-248 CROWBAR (200V EACH) K80 S79/1 TO INTERLOCK CHAIN R24 TO "BEAM CURRENT" CONSOLE METER R3-4 R3-3-B (32 x 100k) 1K .005 OHM 32 x 100K 150W "PULSE LENGTH" TO CROWBAR 32 x 100K @ 200W R56 @ 200W R39 R46 (DWG. 430_102) 240k K40B R90 3.2M 525k, R41 R89 (16 x 15k, 200W) 3120 (32 x 100k) C1-1 C1-2 C1-3 C1-248 7kW 1 uF 0.67 OHM, 1kW 6400 W 3120 0.15uF REMOVE 6400 W 120kV PULSECW METER SHUNT FRAME ON FLOOR AT END OF CAP BANK RACK B+ BUS (NEAR GROUND) B+ BUS (NEAR GROUND) SHORTING BAR C33 E13 R42 SOLENOIDS 1 uF 1.5KV 100 DISCONNECT 1kV 10W K40 K39 (5) (3) 31 mA AT 100kV BEAM VOLTAGE 3 CAPACITOR FAULT DISCONNECT DETECTOR (AT RIGHT- FROM DWG 2 M17 HAND END OF CAP BANK) R40 C32 J349C106 50mA FS E11 A 100 1uF 1.5KV 2W 200V EARTH GROUND 430 TRANSMITTER CAPACITOR FAULT STATUSTO K59 DWG 430_106 p2 DWG. 430_AGE THIS LINE IS GROUNDED IF CURRENT THROUGH METER M9 IS TOO LOW AC COMMON TITLE: CAPACITOR BANK KLYSTRON AGING SET-UP AND BEAM VOLTAGE CIRCUITRY DRAWN 12-98 TO REPLACE D349C105 TURN OFF MODULATOR VIA BREAKER NEAR file:430_105.ecw jbh 12-17-98 rev 8-7-02 DOOR OF KLYSTRON VAULT KLYSTRON AGING SET-UPfile:430_age.ecw jbh 2-24-03.