MF1337-02a CMOS 8-BIT SINGLE CHIP MICROCOMPUTER S5U1C88816P Manual (Peripheral Circuit Board for S1C88816/8F360) NOTICE No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from the Ministry of International Trade and Industry or other approval from another government agency. © SEIKO EPSON CORPORATION 2001 All rights reserved. Configuration of product number Devices S1 C 88104 F 0A01 00 Packing specifications 00 : Besides tape & reel 0A : TCP BL 2 directions 0B : Tape & reel BACK 0C : TCP BR 2 directions 0D : TCP BT 2 directions 0E : TCP BD 2 directions 0F : Tape & reel FRONT 0G : TCP BT 4 directions 0H : TCP BD 4 directions 0J : TCP SL 2 directions 0K : TCP SR 2 directions 0L : Tape & reel LEFT 0M : TCP ST 2 directions 0N : TCP SD 2 directions 0P : TCP ST 4 directions 0Q : TCP SD 4 directions 0R : Tape & reel RIGHT 99 : Specs not fixed Specification Package D: die form; F: QFP Model number Model name C: microcomputer, digital products Product classification S1: semiconductor Development tools S5U1 C 88348 D1 1 00 Packing specifications 00: standard packing Version 1: Version 1 Tool type Hx : ICE Ex : EVA board Px : Peripheral board Wx : Flash ROM writer for the microcomputer Xx : ROM writer peripheral board Cx : C compiler package Ax : Assembler package Dx : Utility tool by the model Qx : Soft simulator Corresponding model number 88348: for S1C88348 Tool classification C: microcomputer use Product classification S5U1: development tool for semiconductor products S1C88 Family CONTENTS S5U1C88816P Manual (Peripheral Circuit Board for S1C88816/8F360) In this manual we will provide explanations covering such areas as the installation of the S1C88816/8F360 Peripheral Circuit Board (S5U1C88816P) that provides the S1C88816/8F360 emulation functions to the debugging tool ICE (S5U1C88000H5) for the 8-bit single chip microcomputer S1C88 Family, and the operating test procedure. For details on the functions and operation of the ICE, refer to the manual that has been prepared for it. Contents 1 INTRODUCTION ______________________________________________ 1 1.1 S5U1C88816P Outline ............................................................................................. 1 1.2 S5U1C88816P Components ..................................................................................... 1 1.3 S5U1C88816P External Diagram ............................................................................ 1 2 INSTALLATION INTO THE ICE (S5U1C88000H5) __________________ 2 3 PRECAUTIONS ________________________________________________ 3 3.1 Precaution for Operation ......................................................................................... 3 3.2 Differences from Actual IC....................................................................................... 3 4 NAMES AND FUNCTIONS OF PARTS ____________________________ 5 5 CONNECTION TO TARGET SYSTEM_____________________________ 6 6 OPERATION CHECK ___________________________________________ 9 7 PRODUCT SPECIFICATIONS ___________________________________ 10 S5U1C88816P MANUAL EPSON i (PERIPHERAL CIRCUIT BOARD FOR S1C88816/8F360) 1 INTRODUCTION 1.1 S5U1C88816P Outline The S5U1C88816P board provides the peripheral 1 INTRODUCTION circuits other than the core CPU, for the S1C88816/ 8F360. Consequently, you should install it into the ICE and use it as the emulator for the S1C88816/ 1.2 S5U1C88816P Components 8F360 models. The S5U1C88816P is equipped with LEDs and When unpacking the S5U1C88816P, check that the terminals for monitoring the internal operating following goods are present: conditions, I/O connection connectors for the (1) S5U1C88816P board .......................................1 target system and other appropriate devices. (2) I/O connection cable (80-pin/40-pin flat type (3) I/O connector for target system (40-pin) ......... 4 (60-pin/30-pin flat type × 2) .. 2 sets × 2) .. (4) Cable for monitor terminal (10-pin) ................ 1 1 set (5) S5U1C88816P Manual (Peripheral (30-pin)Circuit ......... 2 Board for S1C88816/8F360) (this manual) ..... 1 (6) Warranty ..........................................................1 (7) Warranty registration card ...............................1 1.3 S5U1C88816P External Diagram (8) Report on the factory test ................................. 1 (9) Note for using ..................................................1 Monitor pins Mother board J1 connector OSC1CR GND OSC3CR Mother board J2 connector VR3 (OSC3CR ADJ) VR2 (OSC1CR ADJ) I/O#1 connector ∗ The name 'PRC88816' on the VSVD MONITOR development tool is the old RESET VDC1 OSCC SVDON LCDC LCD5.5V I/O #1 name of the product. VDC0 VDC2 MODE HVLD LCD4.5V EXLCD I/O #3 I/O #2 PRC88816 E0C88816/F360 Peripheral circuit board EPSON VSVD volumeMonitor connectorI/O#2 for LEDconnector RESET switch LED I/O#3 connector Fig. 1.3.1 S5U1C88816P external drawing Note: Keep the JP switch on the S5U1C88816P board as it was set prior to factory shipment. In no case should you remove it or change it. S5U1C88816P MANUAL (PERIPHERAL CIRCUIT BOARD FOR S1C88816/8F360) EPSON 1 2 INSTALLATION INTO THE ICE (S5U1C88000H5) 2 INSTALLATION INTO THE ICE (S5U1C88000H5) S5U1C88816P.Insert the S5U1C88816P along by the upper guide rail of the ICE, until it touches the edge of the ∗ The name 'ICE88UR' on the development tool is the old name of the product. Note: The S5U1C88816P may fail to operate ifICE88UR it is not adequately mounted, so be sure to mount it VSVD RESET VDC1 OSCC SVDON LCDC LCD5.5V MONITOR I/O #1 securely. VDC0 VDC2 MODE HVLD LCD4.5V EXLCD I/O #3 I/O #2 PRC88816 E0C88816/F360 Peripheral circuit board EPSON 2 EPSON (PERIPHERAL CIRCUIT BOARD FOR S1C88816/8F360) S5U1C88816P MANUAL 3 PRECAUTIONS 3 PRECAUTIONS Take the following precautions when using the S5U1C88816P: 3.1 Precaution for Operation 3.2 Differences from Actual IC (1) Turn the power of all equipment off before Caution is called for due to the following function connecting or disconnecting cables. and property related difference with the actual IC. If these precautions are overlooked, it may not (2) In normal use, other than when evaluating operate on the actual IC, even if it operates on the power voltage changes, you should turn the ICE with the S5U1C88816P installed. VSVD volume completely to the right. When the SVD reset function has been selected (1) I/O differences using the mask option, resetting will occur The logic level (5 V for the S5U1C88816P), when the VSVD volume is completely to the output drive capability and pull up resistance left, due to the detection of low voltage, causing are different. For this reason, an added circuit the operation of the S5U1C88816P to stop. such as a level shifter may be necessary when Even if the SVD reset function has not been interfacing with the target system. Also input selected using the mask option, since it will be setup time is different therefore, when a circuit set to SVD reset function ON by default setting requiring consideration of the input response until loading the mask option therefore, be sure time, such as a key matrix, is used, you should to turn the VSVD volume all the way to the design the system and the software according right when starting. to the spec. for the actual IC. (3) The ICE has a built-in power supply fixed at 5 V. When the LCD drive power is externally (2) LCD differences supplied to the S5U1C88816P installed in the The output drive capability is different. ICE, it must be 5 V or less. If an external LCD Since there will be difference with the actual IC drive power of more than 5 V is used to supply even for the drive voltage, you should design the VC1–VC5 terminals of the S5U1C88816P, the system and the software in order to adjust both units may be destroyed due to the differ- the characteristics. ence of the interface voltage in the ICE. (3) Analog comparator differences If external power is selected by mask option, it is impossible to adjust contrast by setting the The response time and characteristics of the LCD contrast adjustment registers LC0 to LC3 analog comparator are different. Consequently, (register settings become invalid). you should design the system and the software according to the spec. for the actual IC. (4) The ICE discriminates between maximum mode and minimum mode according to the (4) Current consumption differences value set in the bus mode setup register The current consumption evaluation is impos- (FF00H•D6, D7). Note, however, that maxi- sible. mum/minimum mode is selected by mask option in the S1C88816 and address FF00H is a (5) Function differences general-purpose register that does not indicate <SVD circuit> the