Full-service, independent repair center -~ ARTISAN® with experienced engineers and technicians on staff. TECHNOLOGY GROUP ~I We buy your excess, underutilized, and idle equipment along with credit for buybacks and trade-ins. Custom engineering Your definitive source so your equipment works exactly as you specify. for quality pre-owned • Critical and expedited services • Leasing / Rentals/ Demos equipment. • In stock/ Ready-to-ship • !TAR-certified secure asset solutions Expert team I Trust guarantee I 100% satisfaction Artisan Technology Group (217) 352-9330 | [email protected] | artisantg.com All trademarks, brand names, and brands appearing herein are the property o f their respective owners. Find the GE PC2IP IIB at our website: Click HERE GE M EDICAL S YSTEMS DIRECTION 2300164-100, R EVISION 7 VIVID ™ 3 P RO /V IVID ™ 3 S ERVICE M ANUAL 7-4-4 External Keyboard Diagnostic Test The external keyboard diagnostic tests enable you to test the buttons and lights on the keyboard in different modes. Note: To test the keys on the alphanumeric keyboard, refer to the Keyboard Diagnostic Test section, on page 7-76. 7-4-4-1 Manual External Keyboard Test 1) Access the HW Diagnostics menu, as described in the Accessing the Back End Diagnostic Options section, on page 7-68. 2) Trackball to the External Keyboard button and press Select . The Extended Keyboard Test window is displayed, as shown below: Figure 7-48 Test Manager Tab - Extended Keyboard Test Window 3) In the Test Manager tab, trackball to the Manual radio button and press Select . 4) Trackball to the KB Panel tab and press Select . The KB Panel tab is displayed, as shown in Figure 7-49 on page 7-74. Chapter 7 - Diagnostics/Troubleshooting 7-73 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com GE M EDICAL S YSTEMS DIRECTION 2300164-100, R EVISION 7 VIVID ™ 3 P RO /V IVID ™ 3 S ERVICE M ANUAL Figure 7-49 KB Panel Tab - Extended Keyboard Test Window 5) Press each of the control panel buttons (except for Select , Menu and the On/Off button), and verify that the correct buttons are activated on-screen in the KB Panel tab. 6) Push each of the rocker switches, and verify that the correct rockers are activated on-screen in the KB Panel tab. 7) Rotate each of the rotaries, and verify that the correct rotaries are activated on-screen in the KB Panel tab. 8) Slide each of the sliders, and verify that only the correct sliders are activated on-screen in the KB Panel tab. 9) Press the soft keys, and verify that only the correct soft keys are activated on-screen in the KB Panel tab. 10) Connect the Footswitch to the connector on the front panel of the unit, and press the right, middle and left of the switch. Verify that the numbers {68}, {69} and {70} accordingly are displayed on the info bar. 11) When you are finished, trackball to the Exit button and press Select . 7-4-4-2 Automatic Lights Test 1) Access the HW Diagnostics menu, as described in the Accessing the Back End Diagnostic Options section, on page 7-68. 2) Trackball to the External Keyboard button and press Select . The Extended Keyboard Test window is displayed, as shown in Figure 7-48 on page 7-73. 3) In the Test Manager tab, trackball to the Lights (Auto) radio button and press Select . 4) Trackball to the Start button and press Select . Verify that all the LEDs are illuminated. 5) Press the Preset button on the keyboard, and then trackball to the Start button and press Select . Ensure that the Select checkbox is selected in the KB Panel tab. Verify that all the backlights on the alphanumeric and extended keyboards are illuminated. 6) When you are finished, trackball to the Exit button and press Select . 7-74 Section 7-4 - Performing Back End Diagnostics on the System Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com GE M EDICAL S YSTEMS DIRECTION 2300164-100, R EVISION 7 VIVID ™ 3 P RO /V IVID ™ 3 S ERVICE M ANUAL 7-4-4-3 Manual Lights Test 1) Access the HW Diagnostics menu, as described in the Accessing the Back End Diagnostic Options section, on page 7-68. 2) Trackball to the External Keyboard button and press Select . The Extended Keyboard Test window is displayed, as shown in Figure 7-48 on page 7-73. 3) In the Test Manager tab, trackball to the Lights (Manual) radio button and press Select . 4) In the KB Panel tab, deselect the Select checkbox. Verify that after the Select LED is off, the alphanumeric keyboards LEDs are dimmed. 5) When you are finished, trackball to the Exit button and press Select . 7-4-4-4 Commands History Select the Commands History tab in the Extended Keyboard Test window to view a report of the activity of the extended control panel during the test, as shown below: Figure 7-50 Commands History Tab - Extended Keyboard Test Window 7-4-4-5 General Configuration Select the General Configuration tab in the Extended Keyboard Test window to set the type of log files that is generated, for example an error log or no log at all. Chapter 7 - Diagnostics/Troubleshooting 7-75 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com GE M EDICAL S YSTEMS DIRECTION 2300164-100, R EVISION 7 VIVID ™ 3 P RO /V IVID ™ 3 S ERVICE M ANUAL 7-4-5 Keyboard Diagnostic Test The keyboard diagnostic test enables you to check the functionality of the alphanumeric keyboard keys. 1) Access the HW Diagnostics menu, as described in the Accessing the Back End Diagnostic Options section, on page 7-68. 2) Trackball to the Keyboard button and press Select . The Keyboard Test dialog box is displayed, as shown below: Figure 7-51 Keyboard Test Dialog Box 3) Follow the on-screen instructions. 4) When you are finished, trackball to the Close button and press Select . 7-76 Section 7-4 - Performing Back End Diagnostics on the System Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com GE M EDICAL S YSTEMS DIRECTION 2300164-100, R EVISION 7 VIVID ™ 3 P RO /V IVID ™ 3 S ERVICE M ANUAL 7-4-6 Media Driver Diagnostic Test The media driver diagnostic test enables you to check the functionality of the MOD, if installed, as well as the functionality of the CD Writer, if installed. 7-4-6-1 MOD Diagnostic Test WARNING: Do not run an MOD Diagnostic Test on MO media that is being used by the customer as a back-up device, since this test may cause unrecoverable damage to any backed-up patient information on the MO media. 1) Insert a new MO Media Sony EDM-2300B (2.3G) into the MOD. 1) Access the HW Diagnostics menu, as described in the Accessing the Back End Diagnostic Options section, on page 7-68. 2) Trackball to the Media Driver button and press Select . The Util_MO_CDR_App dialog box is displayed, as shown below: Figure 7-52 Util_MO_CDR_App Dialog Box 3) Trackball to the MO radio button and press Select . 4) Trackball to the IsMediaAccess button an press Select . The message Media in drive G is accessible is displayed. 5) Trackball to the Eject button and press Select . The message Media is outside is displayed. Verify that the media has actually been ejected. 6) Trackball to the Load button and press Select . The message Media is inside is displayed. Verify that the media is actually inside. 7) Trackball to the Format button and press Select . The message Media in drive G was formatted successfully is displayed. 8) Trackball to the GetVolInfo button and press Select . The message Media in drive G has following properties: Media Label = MY_LABEL, Media File-System Name = FAT is displayed. 9) Trackball to the GetBtPSector button and press Select . The message The Bytes Per Sector value of media in drive G is 512 is displayed. 10) Trackball to the SetVolLabel1 button and press Select .The message Media Label set to TEST_LABEL1 is displayed. Chapter 7 - Diagnostics/Troubleshooting 7-77 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com GE M EDICAL S YSTEMS DIRECTION 2300164-100, R EVISION 7 VIVID ™ 3 P RO /V IVID ™ 3 S ERVICE M ANUAL 11) Trackball to the <GetVolInfo> button and press Select . The message Media in drive G has following properties: Media Label = TEST_LABEL, Media File-System Name = FAT is displayed. 12) Trackball to the Exit button and press Select . 7-4-6-2 CD Writer Diagnostic Test 1) Insert a new recordable CD X16 in the CDR drive. 2) Access the HW Diagnostics menu, as described in the Accessing the Back End Diagnostic Options section, on page 7-68. 3) Trackball to the Media Driver button and press Select . The Util_MO_CDR_App dialog box is displayed, as shown in Figure 7-52 on page 7-77. 4) Trackball to the CDR radio button and press Select . 5) Trackball to the IsMediaAccess button and press Select . The message Media in drive H is accessible is displayed. 6) Trackball to the Eject button and press Select . The message Finalize Media? is displayed. 7) Select No . The message Media is outside is displayed. Verify that the media has actually been ejected. 8) Trackball to the Load button and press Select . The message Media is inside is displayed. Verify that the media is actually inside. 9) Trackball to the Format button and press Select . The message Media in drive H was formatted successfully is displayed.