Ultra Slow Motion Camera 3-Chip High Definition High Speed Camera System Quick Guide Mar 14, 2014 1 Table of Contents 1 Firmware Version 2 Quick Overview of Specifications 3 Setup and Connections 4 CCU Quick Guide 5 Format Selection and H / V Phase Adjustment 6 Capture Size 7 Monitor Information Caption 8 OCP Quick Guide 9 Slow Controller Quick Guide 10 Table of Recording Speed and Time 11 Camera Head Menu 12 Trouble Shooting 13 Precautions when using SHED-HDX Systems of Telecast Fiber Systems, Inc. 14 Camera Head / CCU / OCP / Slow Controller / Pin Assignment of Connectors 2 1 Firmware Version This document is based on the following firmware versions. Please refer to the versions before you read this document. ・ Version : Camera Head You can check the versions at MENU(1/2) > OTHER INFO > VERSION in 11. Camera Head Menu I/F PART UPDATE ・ FW ：01.08.19 ・ PIF ：01.00.07 ・ MEM ：02.04.00 ・ SNS ：02.07.00 PROC PART UPDATE ・ FW ：01.12.05 ・ PROC1 ：01.37.41 ・ PROC2 ：01.74.00 ・ Version : OCP Press INFO button on OCP You can check the versions at INFORMATION 5/5 on the touch screen. Please check if the versions and Check Sum of OCP-200 / CCU-970HM are as follows. OCP-200 (SDHC) Hi-Moiton2 Program No. Program No. STR-5088V14.02.00 STR-5634V01.12.05 Check Sum 8099 Check Sum CCU-970HM Program No. Program No. STR-5633V01.00.04 Check Sum Check Sum 7444 ・ Version : Slow Controller Version information is displayed on the LCD panel approx. 2secs after turning on the power and “initialize…” message. Please confirm the version is “MDC50T-NAC09 S0130-53”. 3 2 Quick Overview of Specifications 2.1. Camera Head 1 Image Sensor 3x CMOS (Global Shutter), 2/3-inch Optical System 2 Effective picture elements 1920x1080 3 Lens Mount B4 Mount 4 Sensitivity F8 at 2000lx (5600K, 89.9% reflectance, at 1080 mode) 5 Signal-to-noise ratio 61.9dB at LIVE, 58.5dB at REPLAY* *FRCR-ON, FRGA-4, FRTH-3 at 1080 mode 6 Operation temperature -15 to +40 degrees C 7 Storage temperature -30 to +60 degrees C 8 Memory 96GB (32GB x 3ch) 9 Frame rate 24 to 1000 fps, 1fps step 10 Recording time 38 Sec. (300fps) 11 Power Consumption 186W (with Lens and 2”VF) 12 Dimensions (W x H x D) 146 x 326 x 456 mm 13 Weight 7 Kg (without VF and lens) 2.2. CCU 1 FORMAT 1080i or 720p / 59.94 or 50Hz 2 Power supply AC 100 / 110 / 117 / 220 / 240 V ±10% 3 Power consumption approx. 290 - 510VA (Camera , 9"VF and CCU) 4 Operating temperature -0 to +45 degrees C 5 Storage temperature -30 to +60 degrees C 6 Dimensions (W x H x D) 483 x 133 x 454 mm 7 Weight 28 Kg 4 3 Setup and Connections 3.1 OB Style 5 3.2 Standalone Style 6 4 CCU Quick Guide 4.1 Rear Panel A AC IN AC100V/110V/117V/220V/240V ±10% B OPT Optical Fiber Connection C MIC OUT MIC Direct Output from the MIC Input of Camera D SLOW-CTRL Slow Controller Connection E TRUNK RS-422 Communication with Camera Head(Optional) F TALLY IN Tally Signal Input G INTERCOM Intercom Signal Connection H RET IN Return Signal Inputs via max. 4ch x HD-SDI I OCP OCP Cable Connection J GENLOCK Genlock Signal Connection for either HD Tri-sync or SD-BB Signal K SYNC OUT HDTV tri-level Signal Output for external devices L WFM WFM Connection, 1 for LIVE-OUT, 2 for REPLAY-OUT (*) M HD-SDI OUT There are 6 (six) BNC Connections as follows 1 HD-SDI 1 Live Output at All Times (*) 2 HD-SDI 1 Live Output at All Times (*) 3 HD-SDI 2 Replay Output (*) 4 HD-SDI 2 Replay Output (*) 5 PM1(Picture Monitor 1) Output for OCP Operator. Characters Signal is overlaid 6 PM2(Picture Monitor 2) Output for V/T Operator. Characters Signal is overlaid (*) When the system format is set in 1080I59/720P59/1080I50/720P50, the output image becomes this. When the system format is set in 1080P59/1080P50, all the output images are Live or replay. SYNC OUT TRUNK SLOW-CTRL RET IN OCP OPT TALLY IN GENLOCK AC IN MIC OUT INTERCOM HD-SDI WFM OUT 7 4.2 Front Panel A POWER 1 MAIN Power switch of CCU 2 HEAD Power switch of Camera Head B CABLE Indicator 1 OPTICAL LEVEL Status of Optical communication of camera cable ・ ○●●● 1.OK The cable is in good condition ・ ○●●○ 2.ATTENTION Cleaning recommended, but still usable ・ ○●○○ 3.WARNING Problem in communication. Must clean the cable ・ ●○○○ 4.NG Not usable. Change the cable. 2 CAMERA CABLE Status of camera cable ・ ●NORMAL Status is normal. ・ ●OPEN The cable may be disconnected or snapped ・ ●SHORT The cable may be short-circuited. C MIC 1 ON Turns ON Sound communication from MIC of CCU front to Camera Head 2 OFF Turns OFF Sound communication from MIC of CCU front to Camera Head 3 PTT Turns ON MIC of CCU front only while the switch is at PTT position. D INCOM 1 PRIV Deactivates Engineer line of INTER COM connector on the rear panel of the CCU. 2 COMM Activates Engineer line of INTER COM connector on the rear panel of the CCU E REMOTE / LOCAL Please set to LOCAL. REMOTE is inactive. F FAN ALARM The indicator lights on when CCU fan stops. 8 5 Format Selection and H / V Phase Adjustment 5.1 Format Selection The Hi-Motion II supports 1080I59, 720P59, 1080P59, 1080I50, 720P50 and 1080P50 system format. These are selectable as the image signal output. A How to change System Format of different frequency (e.g. 1080/59.94i <-> 1080/50i) Change both settings on the Camera Head and the CCU as follows. The Camera must be changed first and the CCU second. NOTE: GENLOCK must be disconnected before the setting. 1. Open the HEAD MENU on the VF output and change the FORMAT SELECT of CAMERA HEAD FORMAT on ENGINEER(1//2). 2. Turn off the power of the Camera 3. Show the color bar on PM1 output of the CCU by pressing BARS button on the OCP. 4. Press SETUP button on the OCP and press CHARACTER button on the touch screen. 5. Keep pressing MENU button on the OCP to open the Main Menu of the CCU 6. Select one in the SYSTEM FORMAT by turning the Select Knob or the Next Knob, and press ENTER button. 7. Change the Frame Rate that is the same as the Camera Format. 8. Turn off the power of the CCU and reboot the system to complete the settings. B How to change System Format of the same frequency (e.g. 1080/59.94i <-> 720/59.94p) Change settings on the CCU as follows, so that the Camera settings are changed automatically. NOTE: GENLOCK must be disconnected before the setting. 1. Show the color bar on PM1 output of the CCU by pressing BARS button on the OCP. 2. Press SETUP button on the OCP and press CHARACTER button on the touch screen. 3. Keep pressing MENU button on the OCP to open the Main Menu of the CCU 4. Select one in the SYSTEM FORMAT by turning the Select Knob or the Next Knob, and press ENTER button. 5. Change the Frame Rate. At that time, the camera reboots automatically. 6. Turn off the power of CCU and reboot the system to complete the settings. 9 5.2. Output video when set to 1080P When the system format is set to 1080P, unlike 1080I/720P setting, all output images of the camera head and CCU become the common image. - When select the LIVE image, all output images become the LIVE image. - When select the PLAY image, all output images become the PLAY image. This section explains the switching the output image when set to 1080P. A Switching between LIVE and PLAY images The Switching between LIVE and PLAY images is applied to all output images by performing the following operation. 1. Set the value of the selection item [PM1] of the OCP to either LIVE or PLAY. 2. Press the STANDBY button on the slow controller, and set LIVE or PLAY image. 3. Select VIDEO OUTPUT MODE on the head menu MENU (1/2) page, select VF OUT SEL, and then set LIVE or PLAY. 4. Select VIDEO OUTPUT MODE on the head menu MENU (1/2) page, select MON OUT SEL, and then set LIVE or PLAY. * When set the PLAY image, VF output becomes the same PLAY image. Like 1080I/720P setting, you cannot always output LIVE image. B Switching between recording and playing When operating recording and playing, the output image is sometimes different from the image set in 1080l/720P. ●Operation when outputting LIVE image 1. Showing a selected block which is on recording - Once the trigger is inputted, recording ends and the image switches from LIVE to PLAY showing still image of the block. 2. Showing a selected block which has been already recorded - Press STOP button and then switches from LIVE to PLAY showing still image of the block. - Press PLAY button and then switches from LIVE to PLAY showing replay image of the block. - Operate by JOG/SHTL/T-Bar and then switches from LIVE to PLAY showing replay image of the variable speed of the block. 3. Moving to the other block - When the other block is selected, LIVE/PLAY image switches according to the status of the selected block.