Phoenix ® Software V9 Series Programmer’s Reference for Hypertherm Touchscreen Shape Cutting Controls 806420 — Revision 4 Hypertherm, Inc. Etna Road, PO Box 5010 Hanover, NH 03755 USA Phone: 603-643-3441 Fax: 603-643-5352 DISCLAIMER The information in this document is subject to change without notice and should not be construed as a commitment by Hypertherm, Inc. Hypertherm Inc. assumes no responsibility for any errors that appear. TRADEMARKS Command, EDGE, HT 4400, HD3070 HyDefinition Plasma and HD4070 HyDefinition Plasma, HyperCAD, HyperNet, HyperNest, Phoenix, Powermax65, Powermax85 and ShapeWizard are registered trademarks of Hypertherm, Inc. Align, APC, ArcGlide, CutPro, EDGE Pro, FASTLaser, Gemini, HPR130, HPR260 HyPerformance Plasma, HyPath, Mariner, Nester, Remote Help, Sensor, and Voyager are trademarks of Hypertherm, Inc. HASP is a registered trademark of Aladdin Knowledge Systems Ltd. Indramat is a trademark of Bosch Rexroth. Pacific Scientific is a trademark of Danaher Motion. Pentium and Celeron are registered trademarks of Intel Corporation. Virus Scan is a registered trademark of McAfee Associates, Inc. Microsoft, the Microsoft logo, and Windows are registered trademarks of Microsoft Corporation. NJWIN is a registered trademark of NJStar Software Corporation. SERCOS Interface is a trademark of SERCOS North America. Norton AntiVirus and Norton Ghost are trademarks of Symantec Corporation. Other trademarks are the property of their respective holders. COPYRIGHT 2011 by Hypertherm, Inc. All rights Reserved Printed in USA Phoenix Software V9 Series Programmer’s Reference (P/N 806420) Revision 4 – August, 2011 Hypertherm, Inc. Hanover, NH USA www.hypertherm.com © 2011 Hypertherm, Inc. All Rights Reserved Hypertherm, Inc. Hypertherm Europe B.V. Etna Road, P.O. Box 5010 Vaartveld 9 Hanover, NH 03755 USA 4704 SE 603-643-3441 Tel (Main Office) Roosendaal, Nederland 603-643-5352 Fax (All Departments) 31 165 596907 Tel [email protected] (Main Office Email) 31 165 596901 Fax 800-643-9878 Tel (Technical Service) 31 165 596908 Tel (Marketing) [email protected] (Technical Service Email) 31 165 596900 Tel (Technical Service) 800-737-2978 Tel (Customer Service) 00 800 4973 7843 Tel (Technical Service) [email protected] (Customer Service Email) Hypertherm Japan Ltd. Hypertherm Automation Level 9, Edobori Center Building 5 Technology Drive, Suite 300 2-1-1 Edobori, Nishi-ku West Lebanon, NH 03784 USA Osaka 550-0002 Japan 603-298-7970 Tel 81 6 6225 1183 Tel 603-298-7977 Fax 81 6 6225 1184 Fax Hypertherm Plasmatechnik GmbH Hypertherm Brasil Ltda. Technologiepark Hanau Avenida Doutor Renato de Rodenbacher Chaussee 6 Andrade Maia 350 D-63457 Hanau-Wolfgang, Deutschland Parque Renato Maia 49 6181 58 2100 Tel CEP 07114-000 49 6181 58 2134 Fax Guarulhos, SP Brasil 49 6181 58 2123 (Technical Service) 55 11 2409 2636 Tel 55 11 2408 0462 Fax Hypertherm (S) Pte Ltd. 82 Genting Lane Hypertherm México, S.A. de C.V. Media Centre Avenida Toluca No. 444, Anexo 1, Annexe Block #A01-01 Colonia Olivar de los Padres Singapore 349567, Republic of Singapore Delegación Álvaro Obregón 65 6841 2489 Tel México, D.F. C.P. 01780 65 6841 2490 Fax 52 55 5681 8109 Tel 65 6841 2489 (Technical Service) 52 55 5683 2127 Fax Hypertherm (Shanghai) Trading Co., Ltd. Hypertherm Korea Branch Unit A, 5th Floor, Careri Building #3904 Centum Leaders Mark B/D, 432 West Huai Hai Road 1514 Woo-dong, Haeundae-gu, Busan Shanghai, 200052 Korea, 612-889 PR China 82 51 747 0358 Tel 86-21 5258 3330/1 Tel 82 51 701 0358 Fax 86-21 5258 3332 Fax 03/08/11 Contents Shrink-Wrap License Agreement .............................................................................. L-1 Safety .......................................................................................................................... S-1 Chapter 1 Editing Part Programs .............................................................................. 1-1 Shape Library ......................................................................................................................... 1-1 Text Editor .............................................................................................................................. 1-2 Shape Wizard ......................................................................................................................... 1-3 Teach Trace ........................................................................................................................... 1-6 Remnant Trace Mode ......................................................................................................... 1-6 Teach Trace Mode .............................................................................................................. 1-8 HyperCAD ............................................................................................................................ 1-12 Automatic Nesting ................................................................................................................ 1-13 Nesting Screen Layout ..................................................................................................... 1-13 Automatic Nesting Setup .................................................................................................. 1-14 Using Automatic Nesting .................................................................................................. 1-16 Chapter 2 ASCII Codes .............................................................................................. 2-1 Control Codes ........................................................................................................................ 2-1 All Codes ................................................................................................................................ 2-3 Chapter 3 EIA1B RS-274D Program Support ............................................................... 3-1 Directly10B Supported EIA Codes ................................................................................................ 3-1 Mapped EIA Codes ................................................................................................................ 3-9 Unsupported EIA Codes ....................................................................................................... 3-12 EIA13B Comments ..................................................................................................................... 3-14 Chapter 4 ESSI Code Support ................................................................................... 4-1 Mapped ESSI Codes .............................................................................................................. 4-1 Unsupported ESSI Codes ...................................................................................................... 4-5 ESSI Comments ..................................................................................................................... 4-6 i Chapter 5 Advanced Feature Codes ......................................................................... 5-1 Kerf Table Codes ................................................................................................................... 5-1 Special Kerf and G59 Code Settings ...................................................................................... 5-1 Kerf Override ...................................................................................................................... 5-1 G59 Code Override ............................................................................................................. 5-1 Parallel Kerf Enable for Hole Center Piercing ..................................................................... 5-1 Tilt / Rotator Part Codes ......................................................................................................... 5-2 Station Select Codes .............................................................................................................. 5-3 Process Select Codes ............................................................................................................ 5-4 Station Configuration Variables .............................................................................................. 5-4 Lifter .................................................................................................................................... 5-4 Power Supplies ................................................................................................................... 5-4 Laser ................................................................................................................................... 5-5 Automatic Torch Spacing ....................................................................................................... 5-5 Automatic Torch Spacing Program Codes ......................................................................... 5-7 Automatic Torch Spacing I/O .............................................................................................. 5-7 Automatic Plate Alignment Codes ...................................................................................... 5-7 Example Part Program ........................................................................................................... 5-8 Dual Transverse without Beveling .......................................................................................... 5-9 Beveling .................................................................................................................................