Attachment E205: Surface Coating or Printing Operations Supplemental Application Form DEEP USE ONLY Applicant Name: App. No.: Unit No.: Complete this form in accordance with the instructions (DEEP-NSR-INST-205) to ensure the proper handling of your application. Print or type unless otherwise noted. Note: Certain surface coating operations may be operated pursuant to RCSA section 22a-174-3b or -3c in lieu of a permit to construct and operate pursuant to RCSA section 22a-174-3a. Complete a separate form for each type of part to be coated or each printing operation. Questions? Visit the Air Permitting web page or contact the Air Permitting Engineer of the Day at 860-424-4152. Part I: General Manufacturer and Model Number Construction Date Is this unit subject to RCSA section 22a- 174-20, Control of Organic Compound No Yes, Subsection Emissions? Is this unit subject to Title 40 CFR Part 60, No Yes, Subpart(s) NSPS? Is this unit subject to Title 40 CFR Part 63, No Yes, Subpart(s) MACT? Type of Parts Coated or Printing Operation (check one) Can Coating Aerospace Specialty Coating Metal Coil Coating Aerospace Coating Fabric or Vinyl Coating Graphic Arts Rotogravures or Flexography Metal Furniture Coating Flexible Package Printing Paper, Film or Foil Coating Offset Lithographic or Letterpress Printing Wire Coating Large Appliance Coating Miscellaneous Metal Parts Coating Pleasure Craft Coating Miscellaneous Plastic Parts Coating Other (specify): Automotive-Transportation Plastic Parts Coating Business Machines Plastic Parts Coating Motor Vehicle Materials Coating Bureau of Air Management DEEP-NSR-APP-205 1 of 11 Rev. 01/13/14 Part II: Surface Coating Applicator Data Complete a separate Part II for each surface coating applicator. Applicator ID No. Continuous Manual Mode of Surface Coating Batch Automatic Other (specify): HVLP Gun Airless Electrostatic Spray Other (specify): Transfer Efficiency: % Tank Dimensions (in feet): Dip Tank Length Width Height Capacity gallons gallons Cover Yes No Rotogravure Flexographic Type of Applicator (check one) Lithographic Letterpress Printing Screen Plateless Other (specify): Flow Coating Knife Coating Brush Other (describe): Applicator Maximum Rated Capacity gal/hr Maximum Operating Schedule hours/day hours/year Printing Press Data Heatset or Non-Heatset Heatset (R = 20%) Non-Heatset (R = 95%) (Retention Factor - R) Other: (R = %) Maximum Web Speed: ft/min Web-fed Maximum Web Width: ft 2 Type of Press Maximum Ink Coverage: lb ink/ft Maximum Sheet Area: ft2 Sheet-fed Maximum Press Speed: sheets/hr Bureau of Air Management DEEP-NSR-APP-205 2 of 11 Rev. 01/13/14 Part III: Drying Method Information Drying Method Cured in an Oven (Baked) Air Dried Heat Polymerized Drying Temperature oF Oven Power Source Electric Fuel-Fired Other (specify) Oven Fuel Type (if fuel-fired) Oven Fuel Higher Heating Value Oven Burner Maximum Rated MMBtu per hour Capacity Oven Maximum Annual Fuel Usage Oven Fuel % Sulfur by Weight Bureau of Air Management DEEP-NSR-APP-205 3 of 11 Rev. 01/13/14 Part IV: Coatings Information A. Coatings Inventory This section should list all VOC containing materials used for any type of surface coating. Types of VOC containing materials can include, but are not limited to those listed in Part IV.D of this form which include: coatings, printing inks, fountain solutions, varnish, clear coatings, etc. Cleaning solvents should be listed in Part V of this form. Coating Data (as received) Coating ID: Coating ID: Coating ID: Coating ID: Coating Name Applicator ID(s) Type of Coating (code from Table D below) gal/hr gal/hr gal/hr gal/hr Maximum Coating Usage gal/day gal/day gal/day gal/day gal/yr gal/yr gal/yr gal/yr Coating Density, as received (lbs/gal) Total Volatiles Content (wt%) Solids Content (vol% or wt%) Water Content (wt%) Exempt VOC Content (wt%) Non-Exempt Coating Data (as mixed) Diluent(s) Used (IDs from Table B below) Diluent/Coating Ratio (gal diluent/gal coating) VOC Content Exempt (lb/gal of mixed coating) Non-Exempt Check here if additional sheets are necessary, and label and attach them to this sheet. Bureau of Air Management DEEP-NSR-APP-205 4 of 11 Rev. 01/13/14 B. Diluent Inventory None, go to Part IV.C. Diluent Data Diluent ID: Diluent ID: Diluent ID: Diluent ID: Diluent Name Diluent Density (lbs/gal) Water Content (wt%) Exempt VOC Content (wt%) Non-Exempt C. HAP Inventory If a HAP appears in more than one coating, list the HAP once and provide the highest HAP content in lb/gal. HAP Content, as HAP Content, as HAP Name Coating ID HAP Name Coating ID applied (lb/gal) applied (lb/gal) Check here if additional sheets are necessary, and label and attach them to this sheet. Bureau of Air Management DEEP-NSR-APP-205 5 of 11 Rev. 01/13/14 D. Type of Coating Table If the type of coating is not listed below, use “NS” to designate the coating as a non-specific coating. Code Type of Coating Code Type of Coating Can Coating G16 Pretreatment coating A1 Sheet basecoat (exterior and interior) G17 Repair and touch-up A2 Sheet overvarnish G18 Silicone release A3 Two-piece can exterior basecoat G19 Solar-absorbent A4 Two-piece can exterior overvarnish G20 Vacuum-metalizing A5 Two-piece can interior body spray G21 Drum coating, new, exterior A6 Two-piece can exterior end spray or rollcoat) G22 Drum coating, new, interior A7 Two-piece can exterior end rollcoat G23 Drum coating, reconditioned, exterior A8 Three-piece can interior body spray G24 Drum coating, reconditioned, interior A9 Three-piece can side-seam spray Miscellaneous Plastic Parts A10 End sealing compound H1 General one-component Metal Coil Coating H2 General multi-component B1 Primecoat Electric dissipating coatings and shock-free H3 B2 Topcoat coating B3 Single Coat H4 Extreme performance multi-component Fabric and Vinyl Coating H5 Metallic C1 Fabric coating H6 Mold-seal Vinyl coating (decorative or protective H7 Multi-colored coating C2 topcoats or printing) H8 Optical Coating Metal Furniture Coating H9 Vacuum-metalizing D1 General, one component Automotive-Transportation Plastic Parts Coating D2 General, multi-component High bake coatings – interior and exterior parts D3 Extreme high gloss I1 Flexible Primer D4 Extreme performance I2 Non-flexible Primer D5 Heat-resistant I3 Base Coat D6 Metallic I4 Clear Coat D7 Pretreatment I5 Non-base coat/clear coat D8 Solar-absorbent Low bake/air dried coatings – exterior parts Paper, Film and Foil Coating I6 Primer E1 Paper Coating I7 Base Coat E2 Film Coating I8 Clear Coat E3 Foil Coating I9 Non-base coat/clear coat E4 Pressure sensitive tape and label coating Low bake/air dried coatings – interior parts E5 Pressure sensitive adhesive I10 All Wire Coating Touchup and repair coating F2 Wire Coating I11 All Miscellaneous Metal Parts Business Machines Plastic Parts G1 General one-component J1 Primers G2 General multi-component J2 Top Coat G3 Camouflage J3 Texture Coat G4 Electric-insulating varnish J4 Fog Coat G5 Etching filler J5 Touchup and Repair G6 Extreme high-gloss Motor Vehicle Materials G7 Extreme performance K1 Motor vehicle cavity wax G8 Heat-resistant K2 Motor vehicle sealer G9 High performance architectural K3 Motor vehicle deadener G10 High temperature Motor vehicle gasket/gasket sealing K4 G11 Metallic material G12 Mold-seal K5 Motor vehicle underbody coating G13 Pan backing K6 Motor vehicle trunk interior coating G14 Prefabricated architectural multi-component K7 Motor vehicle bedliner coating G15 Prefabricated architectural one-component K8 Motor vehicle lubricating wax/compound Bureau of Air Management DEEP-NSR-APP-205 6 of 11 Rev. 01/13/14 Code Type of Coating Code Type of Coating Aerospace Specialty Coating L50 Sealant - Sprayable L1 Ablative coating L51 Silicone insulation material L2 Adhesion promoter L52 Solid film lubricant Adhesive bonding primers cured at 250°F or L53 Specialized function coating L3 below L54 Temporary protective coating Adhesive bonding primers cured above L55 Thermal control coating L4 250°F L56 Wet fastener installation coating L5 Adhesive - Commercial interior L57 Wing coating L6 Adhesive - Cyanoacrylate Aerospace Coating L7 Adhesive - Fuel tank M1 Primer – general aviation rework facilities L8 Adhesive - Nonstructural Exterior primer – large commercial aircraft M2 L9 Adhesive - Rocket motor bonding components L10 Adhesive - Rubber-based Exterior primer – fully assembled, large M3 L11 Adhesive - Structural autoclavable commercial aircraft L12 Adhesive - Structural nonautoclavable M4 Primer L13 Aerospace high-temperature coating M5 Topcoat L14 Antichafe coating M6 Topcoat – general aviation rework facilities L15 Bearing coating M7 Self-priming topcoat L16 Caulking and smoothing compounds Self-priming topcoat – general aviation M8 L17 Chemical agent-resistant coating rework facilities L18 Clear coating M9 Type I chemical milling maskant Commercial exterior aerodynamic structure M10 Type II chemical milling maskant L19 primer Graphic Arts Rotogravures and Flexography L20 Compatible substrate primer N1 Publication rotogravure L21 Corrosion prevention compound N2 Packaging rotogravure L22 Cryogenic flexible primer N3 Flexographic printing L23 Cryoprotective coating Flexible Package Printing L24 Dry lubricative material O1 Flexible package printing coatings L25 Electric or radiation-effect coating O2 Flexible package printing adhesives Electrostatic discharge and electromagnetic Offset Lithographic Printing and Letterpress L26 interference (EMI)coating Printing Elevated-temperature Skydrol-resistant P1 Web offset lithographic – fountain solution L27 commercial