P17 Important Precautions—Please Read! Read! Precautions—Please Important P13 Tuning weight performance guide guide performance weight Tuning P11 How to change tuning weights weights tuning change to How P09 QTS sleeve performance guide guide performance sleeve QTS P07 QTS sleeve position overview position sleeve QTS P05 How to remove and install QTS sleeve (sleeve installation) (sleeve sleeve QTS install and remove to How P17 Important Precautions—Please Read! Read! Precautions—Please Important P03 How to remove and install QTS sleeve (torque wrench operation) wrench (torque sleeve QTS install and remove to How P13 Tuning weight performance guide guide performance weight Tuning SRIXON Zシリーズ P01 Part names and features features and names Part P11 How to change tuning weights weights tuning change to How P09 QTS sleeve performance guide guide performance sleeve QTS 取扱説明書/セッティング調整マニュアル P07 QTS sleeve position overview position sleeve QTS Instruction Manual / Setting Adjustments Setting / Manual Instruction P05 How to remove and install QTS sleeve (sleeve installation) (sleeve sleeve QTS install and remove to How P03 How to remove and install QTS sleeve (torque wrench operation) wrench (torque sleeve QTS install and remove to How SRIXON Z Z SRIXON Series 各部の名称と機能SRIXON Zシリーズ P01 P01 Part names and features features and names Part QTSスリーブの脱着方法（トルクレンチの操作） P03 取扱説明書/QTSスリーブの脱着方法セッティング調整マニュアル（スリーブの装着） P05 QTSスリーブのポジション一覧表 P07 Instruction Manual / Setting Adjustments Setting / Manual Instruction QTSスリーブのパフォーマンスガイド P09 チューニングウエイト交換方法 P11 SRIXON Z Z SRIXON Series 各部の名称と機能 P01 チューニングウエイQTSスリーブの脱着方法トのパフォーマンスガイ（トルクレンチの操作）ド P03P13 QTSスリーブの脱着方法重要事項“必ずお読みください”（スリーブの装着） P05P17 QTSスリーブのポジション一覧表 P07 QTSスリーブのパフォーマンスガイド P09 チューニングウエイト交換方法 P11 チューニングウエイトのパフォーマンスガイド P13 重要事項“必ずお読みください” P17 Part names and features Tuning weight Tuning weight Part names and features Able to adjust swing weight and Able to adjust swing weight and Tuning weight preciselyTuning set weight depth of center of precisely set depth of center of gravity (CG) by adjusting weights. gravity (CG) by adjusting weights Able to adjust swing weight and Able to adjust swing weight and on toe and heel. precisely set depth of center of precisely set depth of center of gravity (CG) by adjusting weights. QTSgravity sleeve (CG) by adjusting weights Changeon toe andposition heel. to set desired QTS sleeve face angle, lie angle, and loft angle. Change position to set desired Part names and features face angle, lie angle, and loft angle. Tuning weight Weight port (back) Tuning weight Weight port (toe) Weight port (heel) Part names and features Able to adjust swing weight and Able to adjust swing weight and Tuningprecisely weight set depth of center of Z765 Driver Tuningprecisely weight set depth of center of Weight port (back) Weight port (toe) Weight port (heel) *This product is only available in Ablegravity to adjust (CG) swing by adjusting weight weights.and Z565 Driver Ablegravity to adjust (CG) swing by adjusting weight weightsand Z765 Limited Model Driver selected areas (countries) due to limited quantities. Z765 Driver precisely set depth of center of preciselyon toe setand depth heel. of center of gravity (CG) by adjusting weights. *This gravityproduct (CG) is only by availableadjusting in weights Accessories Custom torque wrench Use only the torque wrench Z565 Driver QTS sleeve Z765 Limited Model Driver selectedon toe areas and (countries heel. ) due to limited quantities. Part names and features Change position to set desired and tuning weights provided. QTSface sleeve angle, lie angle, and loft angle. Accessories Custom torque wrenchTuning weight Use only the torque wrenchTuning weight Use of damaged or Change position to set desired Able to adjust swing weight and Able to adjust swing weight and face angle, lie angle, and loft angle. and tuning weights provided. improperly installed precisely set depth of center of Use of damaged or precisely set depth of center of tuning weights may result gravity (CG) by adjusting weights. gravity (CG) by adjusting weights improperly installed on toe and heel. in injury or product damage. Weight port (back) Weighttuning port (toe) weightsWeight may port result (heel) QTS sleeve Z765 Driver in injury or product damage. Weight port (back) Change position to set desired 01 Weight port (toe) Weight port (heel) *This product is only available in 02 Z565 Driver face angle, lie angle, and loft angle. Z765 Limited Model Driver selected areas (countries) due to limited quantities. Z765 Driver *This product is only available in Z56501Accessories Driver Custom torque wrench Z765 LimitedUse only Model the Drivertorque wrench selected areas (countries) due to limited quantities. 02 and tuning weights provided. Accessories Custom torque wrench Use only the torque wrench Use of damaged or Weight port (back) Weightand port tuning (toe) weightsWeight portprovided. (heel) improperly installed Driver Use of damaged or Z765 tuning weights may result*This product is only available in improperly installed Z565 Driver Z765 Limitedin injury Model or product Driver damage. selected areas (countries) due to limited quantities. tuning weights may result Accessories Custom torque wrench inUse injury only or the product torque damage.wrench 01 and tuning weights provided. 02 Use of damaged or 01 improperly installed 02 tuning weights may result in injury or product damage. 01 02 How to remove and install QTS sleeve (torque wrench operation) Hold the club upright with Supporting the head in your hand, Loosen Tighten 1 the grip resting on the ground. 2 gently insert the torque wrench 3 With the torque wrench 4 With the torque wrench Use this position when loosening into the screw hole. and tightening. aligned with the shaft, aligned with the shaft, turn it counterclockwise. turn it clockwise until you hear a 'click'. Click Shaft and torque Improperly aligned wrench should torque wrench * Be careful not to loosen the screw too much, form a straight line as you may drop the screw and lose the washer. Do not use any tool other than the supplied torque wrench. Always tighten until you hear a 'click'. Also do not use the supplied torque wrench on any other products. Failure to tighten until you hear a 'click' may result in separation Damaged QTS sleeve and/or improperly installed of the club head or product damage. QTS sleeve may result in injury or product damage. * Not compatible with SRIXON Z-STAR series torque wrenches. Position the torque wrench so that it is correctly aligned with the shaft. Failure to insert the tip of the torque wrench firmly into the screw hole may result in damage to the screw. 03 04 How to remove and install QTS sleeve (sleeve installation) 5 Insert the shaft into the head 6 QTS setting examples Align the position line with For -1LOFT(LOFT-1°) For +1LOFT(LOFT+1°) the mark and press straight in. Align the mark on the head with Align the mark on the head with * Illustration shows neutral position “-1LOFT” on the QTS sleeve and press “+1LOFT” on the QTS sleeve and press straight in. straight in. The shaft may not insert fully if the position line and sleeve mark are not correctly aligned. Press the shaft all the way in until the QTS sleeve is completely covered. 05 06 QTS sleeve position overview Initial Position Loft Face positioning Lie angle STD LOFT STD UR Standard loft -1LOFT Standard Upright +1LOFT ±0° −0.5° −1.0° −1.0° −1.0° −0.5° ±0° +0.5° +1.0° +1.0° +1.0° +0.5° Straight face Open face Straight face Closed face ±0° −1.0° −1.5° −2.0° −1.5° −1.0° ±0° +1.0° +1.5° +2.0° +1.5° +1.0° Standard Moderate upright Upright Moderate upright ±0° ±0° +0.5° +1.0° +1.5° +2.0° +2.0° +2.0° +1.5° +1.0° +0.5° ±0° 07 08 QTS sleeve performance guide “If ball flight is too low “If ball flight is too high (ball tends to drop)” (ball tends to rise)” High launch angle for longer carry distance. Stronger flight and more roll(especially into the wind). Example of Example of +1 LOFT -1 LOFT sleeve position sleeve position ( Loft +1˚) on Pg.8. ( Loft -1˚) on Pg.7. *Image *Image Trajectory at initial settingg TrajectoryT after tuningg Trajectory at initial settingg TrajectoryT after tuningg 09 10 How to change tuning weights Hold the clubhead securely in one hand Pull the torque wrench directly Place the desired tuning weight on 1 and the custom torque wrench in the other. 2 up to remove the weight. 3 the tip of the custom torque wrench, Insert the custom torque wrench * If the weight is difficult to remove insert it into the weight port, straight into the hole in the center of lightly jiggle and pull the tuning weight and rotate it clockwise to lock. at the same time with torque wrench the tuning weight and rotate it still inserted. counterclockwise to unlock. Do not use any tool other than the supplied torque wrench. Always tighten until you hear a 'click'. Also do not use the supplied torque wrench on any other products. Failure to tighten until you hear a 'click' may result in separation Improper installation of the tuning weight may result in injury or product damage. of the club head or product damage. Ensure that the tip of the custom torque wrench is fully inserted into the hole of the tuning weight. Hold both the custom torque wrench and the clubhead securely while exchanging the weights. 11 12 Tuning weight performance guide Z765 Driver Z565 Driver Able to adjust to optimal swing weight by changing weights. Weight port (back) Light Swing weight Heavy Extra weight cartridges Made in China 3g 5g 7g 9g 11g 13 g 15 g 3g (aluminum) 5g (titanium) 7g (stainless) 9g (stainless) -3 -2 -1 +1 +2 +3 Points Points Points 0 Points Points Points 11g (tungsten-nickel) 13g (tungsten-nickel) 15g (tungsten-nickel) *9g weight is installed at purchase.