SERIES ZRS STROBES, ZNS HORN STROBES AND SERIES ZNH HORNS Features • Approvals include: UL Standard 1971, UL SNAP Standard 464, New York City (MEA), California The EZ Mount State Fire Marshal (CSFM), Factory Mutual (FM) and Chicago (BFP). See approvals by model number in Specifications and Ordering Information • ADA/NFPA/UFC/ANSI and OSHA 29, Part 1910, 165 compliant • EZ Mount SNAP design, with separate base plate, provides ability to pre-wire the base and test the circuit wiring before the walls are covered • The base plate is protected by a disposable cover Series ZNS Series ZNH and the appliances can quickly snap onto the base after the walls are painted. • Patented EZ Mount Universal Mounting Plate – uses single plate for ceiling and wall mount installations • Wall Mount models feature field selectable candela settings of 15/30/75/110cd and 135/185cd • Ceiling Mount models feature field selectable candela settings of 15/30/75/95cd and Series ZRS Series ZRS 115/177cd • Strobes can be synchronized using the Wheelock Description sync modules or power supplies with built-in sync protocol The Wheelock Series Z notification appliances feature an easy snap on base that is designed to • 12 and 24 VDC models with UL “Regulated simplify the installation and testing of horns, strobes, Voltage” using filtered DC or unfiltered VRMS and horn/strobes. The separate Series Z snap on input voltage base can be pre-wired so circuit wiring can be fully • Strobes produce 1 flash per second over the tested before the appliance is installed and before “Regulated Voltage” range (ZNS, ZRS models) the walls are covered. Once all surrounding work • Selectable Continuous Horn or Temporal (Code- is complete, the appliance can be simply installed 3) Tones with selectable 90 or 95 dBA setting by snaping it on the base. Shorting contacts in the (ZNH, ZNS models) base, which provide continuity for circuit testing, are • Selectable 12 or 24VDC in 1 appliance (ZNH permanently opened when the appliance is installed model) so any subsequent removal of the appliance will indicate a trouble condition on that circuit at the control panel when circuit supervision is enabled. The same base is used for all Series Z horns, strobes and horn/strobes to provide consistent installation and easy replacement of appliances if required. A locking screw is also included for the appliance to provide extra secure installation. The Wheelock Series Z appliances incorporate ZNS, ZNH and ZRS appliances go the same dependable circuitry and high efficiency onto the base plate in a SNAP. optics that are used in Wheelock RSS strobes, NS horn/strobes and NH horns and have the same high performance ratings. The Series Z appliances are compatible with all UL listed “Regulated” panels and all panels that are compatibility listed with Wheelock MEA approved APPROVED RSS, NS and NH appliances. CATALOG NUMBER 5262 NOT TO BE USED FOR INSTALLATION PURPOSES. Mircom reserves the right to make changes at any time without notice in prices, colours, materials, components, equipment, specifications and models and also to discontinue models. NOTE: All CAUTIONS and WARNINGS are identified by the symbol . All warnings are printed in bold capital letters. WARNING: PLEASE READ THESE SPECIFICATIONS AND ASSOCIATED INSTALLATION INSTRUCTIONS CAREFULLY BEFORE USING, SPECIFYING OR APPLYING THIS PRODUCT. VISIT WWW.COOPERWHEELOCK.COM OR CONTACT COOPER WHEELOCK FOR THE CURRENT INSTALLATION INSTRUCTIONS. FAILURE TO COMPLY WITH ANY OF THESE INSTRUCTIONS, CAUTIONS OR WARNINGS COULD RESULT IN IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE, AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS. General Notes: • Strobes are designed to flash at 1 flash per second minimum over their “Regulatedoltage V Range”. • All candela ratings represent minimum effective strobe intensity based on UL Standard 1971. • Series ZNS Strobe products are listed under UL Standards 1971 and 464 for indoor use with a temperature range of 32°F to 120°F (0°C to 49°C) and maximum humidity of 93% (± 2%). • Series ZNH horns are listed under UL Standard 464 for audible signal appliances (Indoor use only). • “Regulated Voltage Range” is the newest terminology used by UL to identify the voltage range. Prior to this change UL used the terminology “Listed Voltage Range”. Table 1: Series ZNS Ratings Per UL Standard 1971 Table 2: Series ZNS/ZNH Horn dBA Ratings Reverberant dBA Anechoic dBA Input Regulated Voltage Strobe Candela @ 10ft per UL 464 @ 10 ft Model Voltage DescriptionVolume VDC Range (CD) 12 24 12 24 VDC/FWR VDC VDC VDC VDC ZNS-MCW 24 16.0 - 33.0 15/30/75/110 Continuous High 83 87 89 95 ZNS-MCWH 24 16.0 - 33.0 135/185 Horn Low 76 81 84 90 ZNS-MCC 24 16.0 - 33.0 15/30/75/95 Code 3 High 79 82 89 95 ZNS-MCCH 24 16.0 - 33.0 115/177 Horn Low 72 76 84 90 Table 3: Series ZNS Average RMS Current* Audible Wall Mount Strobe Models Ceiling Mount Strobe Models Series ZNS/ZNH ZNH-12/24 ZNS-MCW ZNS-MCWH ZNS-MCCZNS-MCCH 24 VDC @24VDC 15cd 30cd 75cd 110cd 135cd185cd 15cd 30cd 75cd 95cd 115cd177cd High (95) dBA 24VDC 0.044 0.074 0.107 0.184 0.244 0.3500.477 0.0820.124 0.2090.275 0.3500.477 Low (90) dBA 24VDC 0.018 0.066 0.101 0.177 0.232 0.3060.429 0.0710.114 0.2010.261 0.3060.429 Audible Series ZNS/ZNH ZNH-12/24 12VDC @12V High (89) dBA 12 VDC 0.021 Low (84) dBA 12VDC 0.012 Table 4: Series ZRS Average RMS Current* ZRS - Wall Mount ZRS - Ceiling Mount ZRS 24VDC MCW MCWH MCC MCCH Models 15cd 30cd 75cd 110cd 135cd 185cd 15cd 30cd 75cd 95cd 115cd177cd 24 vdc 0.060 0.092 0.165 0.220 0.300 0.420 0.065 0.1050.189 0.2490.300 0.420 * RMS current ratings are per UL average RMS method. UL max current rating is the maximum RMS current within the listed voltage range (16-33v for 24v units). For strobes the UL max current is usually at the minimum listed voltage (16v for 24v units). For audibles the max current is usually at the maximum listed voltage (33v for 24v units). For unfiltered FWR ratings, see installation instructions. CAT. 5262 NOT TO BE USED FOR INSTALLATION PURPOSES. page 2 of 4 ZNS/ZNH APPLIANCE ZNS AND ZNH APPLIANCES SYNCHRONIZED WITH SM MOD- Wiring Diagrams ULE SINGLE CLASS “B” NAC CIRCUIT WITH AUDIBLE SILENCE FEATURE ZNS/ZNH APPLIANCE ZNS AND ZNH APPLIANCES SYNCHRONIZEDSM WITH SM MOD- ULE SINGLE CLASS “B” NAC CIRCUIT WITH AUDIBLE+ STROBE SILENCE FEATURE F SM - STROBE Strobe + F A NACSTROBE - CircuitSTROBE NS NH Strobe NAC A C NS +AudiblNH e ZNS/ZNH APPLIANCE ZNS AND ZNH APPLIANCESCircuit SYNCHRONIZED WITH SM MOD- EOLR ULE SINGLE CLASS “B” NAC CIRCUIT WITH AUDIBLE SILENCE C P +Audible - Audible FEATURE SMAudiblEOLRe SIGNAL P NAC- Audible Audible + STROBECircuit SIGNAL NAC F - STROBE StrobeCircuit ZNS AND ZNH APPLIANCES SYNCHRONIZED WITH DSM MODULE NAC NOTE: ZNS/ZNH must be set on Code-3 horn tone A NS NH ZNSDUA ANDL CLASS ZNH APPLIANCES “A” NAC CIRCUIT SYNCHRONIZED WITH NO WITH AUDIBLE DSM MODULE SILENCE FEATURE NOTE:Circuit ZNS/ZNHto achieve must be synchronized set on Code-3 horn temporal tone (Code-3) tone. to achieve synchronized temporal (Code-3) tone. DUAL CLASS “A” NAC CIRCUIT WITH NO AUDIBLE SILENCE FEATURE C Refer+Audibl to installatione instruction (P83983, P83600 Refer to installation instruction (P83983, P83600 DUAL SYNC MODULE respectively).EOLR DUAL SYNC MODULE P respectively). - Audible Audible SYNC + # For detail using SM or DSM Sync Module refer SYNC + # ForNAC detail using SM or DSM Sync Module refer SIGNALSYNC - SYNC - to DataCircuit Sheetto S3000 Data Sheetor Installation S3000 Instructions or Installation Instructions + OU+T1 OUT1 P83123 for P83123SM and P83177for SM forand DSM. P83177 For for DSM. For NOTE: ZNS/ZNH must be set on Code-3 horn tone ZNS AND+ + ZNH APPLIANCES+ IN SYNCHRONIZED1+ IN1 WITH DSM MODULE wiring informationwiring on information the power supplies on the referpower to supplies refer to to achieve synchronized temporal (Code-3) tone. DUAL CLASS- - “A” NAC CIRCUITMINUS1MI NUS1WITH NO AUDIBLE SILENCE FEATURE Installation Instructions P84662 for PS-24-8MC. Refer to installationInstallation instruction Instructions (P83983, P84662P83600 for PS-24-8MC. F F DUAL SYNC+ AU MODUDI+BLAUELEDIBLE respectively). A A SIGNAL # C CIRCUISIGNT ALOUT SYNC + For detail using SM or DSM Sync Module refer C - AUDIBLE P CIRCUIT OUT SYNC- AU- DIBLE to Data Sheet S3000 or Installation Instructions P + OUT1 + OUT2 + - + - P83123 for SM and P83177 for DSM. For + + IN1 OUT2 + - APPLIANCE + - wiring information on the power supplies refer to + + IN2+ APPLIANCE - MINUS1 APPLIANCE - + MINUS2+ IN2 APPLIANCE Installation Instructions P84662 for PS-24-8MC. F - SIGNAL + AUDIMIBLENUS2 CIRCUIT RETURN A SIGNGNALAL C CIRCUIRCUITT OU RET TURN- AUDIBLE P Specifications and+ OUT2 Ordering Information+ - + - + + IN2 APPLIANCE APPLIANCE Sync w/ SM, Agency Approvals - OrderMI NUS2 Strobe 24 12 Mounting Model NumberSIGNAL DSM or CIRCUIT RETURNCode Candela Sync w/VDC SM, VDC Options# Agency Approvals Order Strobe PS-24-8MC 24 12 MountingUL MEA CSFM FM BFP Model Number DSM or Code Candela VDC VDC Options# ZNS-MCW-FR 0304 15/30/75/110XPS-24-8MCX- B, D, E, FX*XUL MEA**CSFM FM BFP ZNS-MCW-FW 0305 15/30/75/110XX- B, D, E, FX*X** Sync w/ SM, Agency Approvals ZNS-MCW-FR Order0304 Strobe15/30/75/ 110 X24 12 X-Mounting B, D, E, FX*X** ModelZNS-MCWH-FR Number 0306 135/185 DSMXX or - B, D, E, FX*X** Code Candela VDC VDC Options# ZNS-MCWH-FWZNS-MCW-FW 03070305 135/18515/30/75/11PS-24-8MC0XX X-X- B, D, E, FX B,UL D, E,MEA FX*XCSFM FM*X**BFP ** ZNS-MCWH-FR 0306 135/185 XX- B, D, E, FX*X**