Hydronic Air Handler for 5100 Series Comfort Plus Furnaces

Hydronic Air Handler for 5100 Series Comfort Plus Furnaces

Hydronic Air Handler for 5100 Series Comfort Plus Furnaces FEATURES: GENERAL: Heavy duty The Steffes Air Handler is insulation an optional device provides designed to interface with maximum the Comfort Plus sound control Hydronic (5100 Series) for quiet furnace to allow it to operation provide forced air heating Durable design as a stand alone furnace with urethane or as a supplement to exterior paint other ducted heating finish systems such as a heat Built-in, pump. When used with a automatic static heat pump, it allows the heat recovery Comfort Plus Hydronic system furnace to serve as the back-up heat source and 5-Year Limited provide comfort Manufacturer’s modulation. Heat pumps Warranty can be operated to much lower temperatures allowing for full utilization of their efficiency while optimizing system performance. A duct sensor constantly monitors outlet air temperature and modulates the precise amount of stored off-peak heat needed to eliminate uncomfortable discharge air temperatures typically associated with heat pump systems during cool outdoor temperatures. The air handler also directs the heat lost statically through the furnace’s outer panels into the ductwork for delivery to the living space (automatic static heat recovery). The internal controls of the Comfort Plus Hydronic furnace automatically regulate the operation of the air handler. OPERATION: A heat call from the room thermostat will energize the pump to circulate a water/glycol solution through the Comfort Plus Hydronic’s heat exchanger where it is heated to the appropriate temperature. This heated water solution is then circulated through the air handler’s water coil. As it passes through the coil, the air handler’s blower system extracts the heat and delivers it to the living space through the ductwork. DIMENSIONAL DIAGRAM: The Steffes Air Handler includes a return plenum, supply air blower, water coil, 21 15/16” (1/2 HP) and air filter. 16 5/8” 24 15/16” (3/4 HP) The air handler’s variable speed blower Supply Air incorporates an ECM motor that Opening automatically adjusts its speed to achieve the appropriate CFM for the Supply Air Blower thermostat input received. Benefits include: Quiet operation Better dehumidification Offers greater operating efficiency by consuming 25% less energy Water Coil during normal operating mode which provides operating cost ) HP HP) savings to the consumer. In Heating/Cooling A-Coil Tray - 1/2 1/2 3/4 continuous fan mode, low speed Front Access ” ( ” ( energy savings can be greater than 1/2 HP: 30” x 22 5/16” x 22 3/4” 11/16 70% in comparison to a standard 11/16 3/4 HP: 33 x 25 5/16” x 22 3/4” 75 fixed motor speed. 72 Interfaces with single or multi-speed air conditioners or heat pumps. With multi-speed systems, it operates at Filter Access a lower speed most of the time 1/2 HP: Fits 20” x 20” x 2” Filter while higher speeds may occur but 3/4 HP: Fits 25” x 20” x 2” Filter only on extremely hot or cold days. This staged heating and cooling Return Air Plenum (opening eliminates temperature swings, into right side, back or enhances comfort and optimizes bottom panel must be cut in efficiency. the field) Improved air filtration in continuous fan mode 23 7/8” 23 1/2” (1/2 HP) Constant air flow over a wide range 26 1/2” (3/4 HP) of static conditions, even if filters are dirty or registers are closed. SPECIFICATIONS: 1/2 HP, 60 HZ 3/4 HP, 60 HZ Variable Speed (ECM) Variable Speed (ECM) Air Handler Air Handler Order Item Number 1302132 1302134 Approximate Weight 200 lbs 225 lbs Maximum Static Pressure (inches water column) .75 inches H20 .75 inches H20 Maximum Water Coil Output 60,000 BTU/hr 90,000 BTU/hr Maximum Outlet Temperature 120oF 120oF A-Coil Tray Dimensions (H x W x D) 30” x 22 5/16” x 22 3/4” 33” x 25 5/16”x 22 3/4” Voltage 240/208 VAC 240/208 VAC Wattage 560W 1,050W CFM ratings 1000, 1200, 1400, 1600 1200, 1400, 1600, 2000 1/2 HP variable speed accommodates most 1.5 to 4 ton heating/cooling systems 3/4 HP variable speed accommodates most 3 to 5 ton heating/cooling systems Steffes 701-483-5400 www.steffes.com [email protected] .

View Full Text

Details

  • File Type
    pdf
  • Upload Time
    -
  • Content Languages
    English
  • Upload User
    Anonymous/Not logged-in
  • File Pages
    2 Page
  • File Size
    -

Download

Channel Download Status
Express Download Enable

Copyright

We respect the copyrights and intellectual property rights of all users. All uploaded documents are either original works of the uploader or authorized works of the rightful owners.

  • Not to be reproduced or distributed without explicit permission.
  • Not used for commercial purposes outside of approved use cases.
  • Not used to infringe on the rights of the original creators.
  • If you believe any content infringes your copyright, please contact us immediately.

Support

For help with questions, suggestions, or problems, please contact us