2-WAY CAR ALARM SYSTEM WITH REMOTE ENGINE START EMODEL 8 IMPORTANT: Please read the entire manual for complete details on the features, accessories and operation before attempting to use your security system. This Security system must be installed by a qualified technician to ensure proper operation. Do not attempt to install or modify this system yourself as this way void your warranty. About Your System Congratulations on your purchase of this state-of-the-art vehicle security system. With proper installation this system will provide superior protection and performance for many years to come. What is included: A control module Tranceiver module One 5-button 2-way LCD remote transmitter One 4-button random code remote transmitter Dual stage shock sensor High output 6-tone siren (optional) Full set wire harness Pin switches Options and Accessories: This system includes several optional inputs and outputs allowing the creation of a completely personalized security and convenience system by offering many optional features such as: 2nd stage door unlock Window close control Channel programme time output Anti car-jack by ignition turn 2pulse signal door unlock Power trunk/hatch release Engine turbo time mode Glass breakage sensor Check range notification Micro-wave detector Arm/disarm chirp on/off Back-up battery siren *Many require additional parts and/or labor, see store for details NOTE: Some of the features described in this manual may required additional parts and/or labor, and may not be included as part of the standard installation of this unit. Additionally, many features of this security system have selectable options that must be activated or programmed during the system's installation. These items will be identified in the following sections. Please discuss these features and any questions you may regarding the installation of this product with your authorized dealer. Functions of remote transmitters The remote transmitters integrated with the security system use the most perfect and reliable radio frequency transfer as opposed to all car security systems being sold at the moment. Some of modern skilled car hijackers use the devices known as code grabbers allowing to accept and keep a signal transferred by the remote control of the car security system. As soon as the driver is out the code is used by the hijacker to disarm the system. Unlike the remote controls described above the remote transmitters integrated with your security system change the code of the transferred signal each time when the button is pressed, therefore, when a hijacker reproduces the signal grabbed from your remote transmitter, the security system just will not react. 2-way remote #TR-45 1-way remote #TX-4R Fig.1 Functions of remotetransmitter buttons Button to arm the system (ARM) Button to disarm the system (DISARM) Button to control remote engine start Button to control Trunk open / CH-1 active Button to check car status , to turn on LCD back light Standard LCD 2-way icon instructions Remote transmitting a signal. Check-in range turn ON status. 2way battery level indication. System Armed. System Disarmed. Silent Armed. Passive arming & Zone1 Zone1 Auto re-arming mode. 1st-stage sensor bypass. 2nd-stage sensor bypass. Zone2 Zone2 1st-stage sensor bypass. 2nd-stage sensor bypass. Panic mode. Door open when armed. Trunk open when armed. Hood open when armed. Zone1 Zone1 Zone2 1st stage sensor triggered. 2nd stage sensor triggered. 1st stage sensor triggered. Zone2 1st stage sensor triggered. Door switch triggered. Trunk switch triggered. Hood switch triggered. Ignition switch triggered. Immobilizer mode. Anti car-jacking mode. Valet mode. Safety mode/ Safe status Remote engine running mode. Clock time engine start mode. Fix time engine start mode. Temperature engine start mode. Turbo mode. Call / page mode. Battery conservemode. Remote button lock Vibrate mode. Remote Function Table: Functions Step Condition Arm and door lock Press once Disarmed & ACC off Arm without siren chirp Press over 2sec. until 1 beep given. Disarmed & ACC off Zone1- 1st-stage bypass Press once within 5sec. of arming. Arming within 5sec. Zone1- 2nd-stage bypass Press twice within 5sec. of arming. Arming within 5sec. Car search mode Press once after 5sec. of arming. Arming after 5sec. Standby Anti-Hi-Jack mode Press over 2sec. Until 1 beep given. ACC ON Disarm and door unlock Press once Armed Disarm without siren chirp Press over 2sec. until 1 beep given. Armed Arm with engine run mode Press over 2sec. Until 1 beep given. Engine running Remote engine start Press over 2sec. then press once. Armed with safe status Remote engine stop Press over 2sec. Engine running mode Safety mode (manual-type car) Press over 2sec. Engine running Zone2- 1st-stage bypass Press once within 5sec. of arming. Arming within 5sec. Zone2- 2nd-stage bypass Press twice within 5sec. of arming Arming within 5sec. Remote Function Table: Functions Step Condition Trunk open / CH-1 active Press over 2sec. until 1 beep given Prolong engine running time Press once, after LCD indicate 3min left. Engine running mode Enable check-in range Press once within 5sec. of arming. Arming within 5sec. Status check & Back light Press once Indoor temperature check Press over 2sec. Until 1 beep given. Silent armed Press over 2sec. Until 1 beep given. ACC OFF Valet mode Press over 2sec. until 1 beep given. ACC ON Panic mode Press over 2sec. until 1 beep given. ACC OFF Anti-Hi-Jack mode Press over 2sec. until 1 beep given. ACC ON FIX time engine start Press once Armed with safe status Temperature engine start Press over 2sec. until 1 beep given. Armed with safe status CH-2 active Press over 2sec. until 1 beep given. CH-3 active Press over 2sec. until 1 beep given. CH-4 active Press over 2sec. until 1 beep given. Functions Step Condition Remote button lock (on/off) Press over 2sec. until 1 beep given. Vibrate mode on/off Press over 2sec. until 1 beep given. Clock time adjust mode Press over 2sec. until 1 beep given. Clock time engine start Press over 4sec. until 2 beep given. Battery conserve mode Press over 2sec. until 1 beep given. Remote battery discharge/replacement If the battery becomes exhausted, the remote will emit extra long beep, While press any button on the remote, few seconds later the indicator will flashing for identify. The battery discharge is displayed on the LCD screen as the icon with the status indicator . Also you can pay your attention that the effective distance for the transmitter is being reduced. To replace the batteries of 2-way remote - Bend the top part of the cover a bit, move it up and remove, - Remove the discharged battery, - Place the new battery (AAA) observing polarity, - Carefully place the cover back. To replace the batteries of 1-way remote - Loose the screws on the back side of the transmitter housing and separate two halves of the transmitter housing, - Remove the discharged battery, - Place the new battery 12V 23A observing polarity, - Carefully place the cover back (please do not damage the LED and switchers on the Circuit board); tighten the screws on the back side of the transmitter housing. Programming of codes for new transmitters Important Please notice that during the programming of a new transmitter into the system memory all previous programmed codes of the transmitters will be erased so in case of programming for additional transmitters the available transmitters shall be programmed again. The system supports in memory up to four codes of remotes irrespective of the fact if the codes of four different remotes or the same code four times is recorded into the system. Programming of new transmitters. Important Please notice that each following operation shall be done within 10 sec after the previous operation. If the 10 second period is over the system will automatically exit the programming mode and two long chirps will acknowledge the exit. If the ignition is turned off during programming the system will immediately exit the programming mode and two long chirps will acknowledge the exit. 1. Disarm the system . 2. Turn the ignition from on to off. 3. Within 10 sec after switching off the ignition press and hold the Valet button over 3 sec , the LED starts flashing , release the Valet button. 4. Press and hold the Valet button, you will hear the siren start chirping (from 1~3 chirp), while give 2 chirp sound, immediately release the Valet button. 5. The LED will start flashing to acknowledging that the system is ready for programming of new transmitters. 6. Press any button of the first transmitter, you will hear 1-short chirp acknowledging that the first transmitter has been programmed Press any button of the second transmitter, you will hear 2-short chirp acknowledging that the second transmitter has been programmed. Repeat the operation 3 for other transmitters. 7. To exit the transmitter programming mode, Turn on the ignition and you will hear two long siren chirps. Programming 2-Way remote Battery conserve mode The mode can be turned on/off 2-way receiving in the Disarmed mode if you simultaneously press down the buttons until the zzz icon turn on. Being in the Disarmed mode the remote pager turns off its receiver in 30sec. To exit the mode, simply press the buttons until zzzz icon turn off. 2-way LCD display : 2way remote button lock ON/OFF For safety purpose, this 2-way remote can be lockout the remote button in order not to mis-touched the buttons. Press button for over 2sec. until one beep is heard, remote button is now locked. To turn on remote button, press button for over 2sec. until two beeps is heard, remote button is now unlocked.