MATEC Web of Conferences 220, 0 3 00 6 (2018) https://doi.org/10.1051/ matecconf/201822003006 ICMSC 2018 Measuring the Torque of a Combustion Engine. 1 1 Josef Popelka , Celestýn Scholz 1technical University of Liberec, Studentská 1402/2, Liberec, Czech Republic, Abstract. This paper deals with the measurement of torque using a designed torque sensor. To determine the indicated engine parameters, the torque along with the torque in the combustion space of the individual cylinders are measured. I worked on the measured values to determine the dependence of the torque moments on the engine load. The obtained data was used to assess the possible use for further measurements. 1 Introduction RPMs of electric machine. Using of this method is not very common because measure is influenced by Over the past few decades, the requirements and criteria significant error of measurement a lot of physical quality. that must be met by car manufacturers are constantly If we improve this measure by adding a torque sensor we increasing. Legislators have considerably contributed to can use electric generator to put load on the engine which this by directly influencing production in the individual is proper and common use alternative. sectors through the creation of various emission regulations and standards. The other side of the coin is 2.1.2 Torque measure with piezoelectric pressure the price, which is of interest to the end consumer. In sensor. addition to price, potential customers are interested in the parameters of the vehicle, such as consumption and the This method is an exclusive solution by AVL Company quantity of pollutants produced. Of course, these two and it is mostly used for the special measuring powertrain parameters are directly proportional to the performance stands or engine dynamometers. Method measures parameters and, therefore, a reasonable compromise pressure directly with pressure sensors inside the needs to be found. Car makers, of course, are searching combustion chamber. If we put normal force into for more ways of achieving better performance with piezoelectric sensor’s silicon plate it generates electric lower or equal consumption. As a way of saving power or charge which is direct proportional to force. We need a fuel, a direct option is to reduce internal engine losses. In characteristic indicated pressure depended on crank shaft order to understand this issue and reduce losses as much angle to get characteristic of indicated torque. We use as possible, there is no suitable measurement method at incremental sensor connected to crankshaft to present. determinate its angle. To get effective torque we need to know friction moment and inertia moment of the engine. 2 Basic methods for measuring torque [3], [4] Torque measuring methods are divided into two basic 2.1.3 Torque determination from inertia moment. groups: Indirect torque measure We can determinate engine’s power, respectively torque Direct torque measure (Measure using torque or by measuring RMPs and time needed to spin body of force sensor) known inertia moment. It is the simplest measuring Special way (Combination) technique and nowadays it is just used at amateur conditions because of great error in measurement. It cannot be used during long-term measure. It can be used 2.1 Indirect torque measure as comparison method with some success. 2.1.1. Torque measure with electric machine. 2.2 Direct torque measure (Measure using In case when combustion engine is connected to electric torque or force sensor) generator is the possibility to measure power, Measure using torque sensors is mostly used of its respectively torque by measuring of voltage, current and accuracy and repeatability. Principe is based on the direct © The Authors, published by EDP Sciences. This is an open access article distributed under the terms of the Creative Commons Attribution License 4.0 (http://creativecommons.org/licenses/by/4.0/). MATEC Web of Conferences 220, 0 3 00 6 (2018) https://doi.org/10.1051/ matecconf/201822003006 ICMSC 2018 torque measure. Differences between each type of sensor 2.2.5 Capacitive sensor. are in physical method used for torque measure. Most of torque sensor is using shaft as a deformation Capacitive sensor is made from two tooth shaped element. Differences between these sensors are that some electrodes which are bonded into a shaft with enough uses own shaft and others use shaft from measured device. tooth space. Shaft deformation causes decreasing of the Second option can by inaccurate sometimes. [1], [5], [6] tooth space by electrode rotation which leads into change Torque sensors types: of capacitive. One of electrodes has to be perfectly • Resistive sensor isolated from the shaft otherwise capacity will not change. • Induction sensor [1], [5], [6] • Capacitive sensor 2.3 Measuring torque by measuring the force on 2.2.1 Resistive sensors a known arm Resistive sensors are most widespread with simply This is a sophisticated method based on measuring the construction. Measure is based on deformation of reaction in the storage of the measured unit. The method measuring element which is shaft in most cases. Sensors s commonly used, for example, with older types of can be divided into two groups. First one uses own shafts dynamometers. An advantage is the simplicity of the putted into measuring track. Second one uses shaft of measuring device, and a disadvantage is measuring errors measured device. [1], [5], [6] affected by the storage of the measured unit. [1] 2.2.2 Sensor with resistive potentiometer. 3 Design of measuring devices for monitoring engine torque Its function is based on angle deviation of measured shaft. Sensor requires significant deformations of measured From the principle of torque measurement, we offer two element. Sensor electronic transforms a resistivity into solutions for obtaining the torque directly from the engine. electric signal that is directly proportional by sensor’s The simplest solution is to use a suitable cylindrical part, deformation. [1], [5], [6] such as a flywheel, to which strain gauges are attached. This method can be used to measure the surface tension 2.2.3 Sensor with resistive tensometer. on the selected part in order to determine the torque. Unfortunately, this method has several pitfalls. Probably Sensor principle is based on the measure of shear stress the largest one is the signal transmission from the rotating with tensometer. Tensometer is very often used sensor part. Another is the very tight space for attaching the because of no requirement of measuring element. strain gauges and the harsh environment between the Unfortunately is necessary to solve signal transmission engine and the gearbox, mainly in terms of temperature. from rotating part. Measured element is mostly cylinder The last important factor is the lack of experience with shape part with several glued tensometer by 45° angle to attaching and subsequently using the strain gauges. The axis of rotation. This assemble creates so called second solution involves the use of industrially- tensometric bridge. [1], [5], [6] manufactured measuring elements. In our case, the measuring flange is the most suitable. A significant disadvantage of this solution is the installation dimensions of the flange, but we have a functional and tested measuring element that can be used. [4] Figure 1. Schema of Tensometric Bridge [1] 2.2.4 Induction sensor. Induction sensor got small air cavity. Angle deviation of shaft is dependable on air cavity change. Sensor’s coil is placed on the stator part, Figure 2. Kistler 4504B measuring flange [2] which also solve signal transmission from rotating shaft. 2 MATEC Web of Conferences 220, 0 3 00 6 (2018) https://doi.org/10.1051/ matecconf/201822003006 ICMSC 2018 Figure 4. Overall view of the measurement elements mounted Figure 3. Model of measuring device [6] on the engine. [3] 3.1 Sensor installation In order to define the space required for installing the measuring flange, we selected a very simple method using composite steel sheet fragments. This is a test design so it is possible to consider a case made from aluminium alloy in the future. The measuring flange is designed by the manufacturer to be subjected to torsional stress only, any other stresses are not permitted. Therefore, the whole system is mounted inside a ball bearing, which captures the axial forces from the clutch disengagement and possible radial forces from the bending stress of the system due to its own weight. [5] Measuring device is designed that by adding another rotating mass into crank shaft it follows that is necessary to remove some material from it for gain get acceptable inertia moment. Table 1. Moment of inertia. Figure 5. Overall view of the measurement elements mounted on the engine. [3] Moment of Weight inertia m [Kg] I [Kg*m2] 4 Experiment flange of crank shaft 0.00452 1.135 sensor 0.01164 1.100 The experimental work was carried out on a supercharged flange of flying wheel 0.01106 2.850 EA 211 1, 4 TSI engine fitted with a sensor for measuring bearing 0.00707 0.910 the pressure inside the cylinders, and the torque, which is original flying wheel 0.073 6.521 measured directly on the crankshaft. The development of adjusting flying wheel 0.03871 4.157 the individual variables was displayed and processed using an AVL Indicom 619 signalling device. Along with To put measuring element into measuring track, the above engine parameters, the courses of the signals on between engine and transmission, is necessary to create the ignition modules and the fuel injectors were measured the case enough which will be a part of the engine. For using the clamp probes. With an engine set up in this way, quite simple manufacture, case is made if you like it is possible to obtain an overview of all of the required assembled from several pieces of plasma cut metal sheet.