INMARSAT-C MOBILE EARTH STATION MODEL FELCOM 15 SAFETY INSTRUCTIONS WARNING WARNING Do not open the equipment. Any repair work must be done by a licensed radio technician. Hazardous voltage which can cause electrical shock, burn Improper repair work can cause electrical or serious injury exists inside shock or fire. the equipment. Only qualified personnel should work inside the equipment. CAUTION Hazardous microwave. Use the proper fuse. Do not approach within Use of a wrong fuse can result in fire or 60 cm of the antenna radome permanent damage to the equipment. when it is transmitting. Microwave radiation can be harmful to the human body, NOTICE particularey the eyes. A warning label is attached to the Radiation Level At terminal and antenna units. Do not remove the labels. If a label is missing 2 10W/m 60 cm or damaged, contact your dealer about replacement. Leave the equipment powered while Antenna Unit underway. Distress cannot be communicated unless the equipment is powered. Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. Name: Warning Label Type: 16-013-2013-1 Turn off the power immediately if water Code No.: 100-251-640 leaks into the equipment or the equip- ment is emitting smoke or fire. Terminal Unit Continued use of the equipment can cause fire or electrical shock. Do not operate the equipment with wet hands. Electrical shock can result. Keep heater away from equipment. Heat can alter equipment shape and melt Name: Warning Label(1) the power cord, which can cause fire or Type: 16-003-1011-0 electrical shock. Code No.: 100-236-230 i (This page intentionally left blank.) ii TABLE OF CONTENTS FOREWORD........................................................................................................vii SYSTEM CONFIGURATION ................................................................................ix PROGRAM NUMBER ...........................................................................................x INMARSAT C SYSTEM.........................................................................................1 Introduction ......................................................................................................................1 Inmarsat C System Configuration ....................................................................................2 Communications Network ................................................................................................4 Peripheral Equipment.......................................................................................................5 1. OPERATIONAL OVERVIEW .........................................................................1-1 1.1 Terminal Unit ....................................................................................................... 1-1 1.1.1 Turning the power on/off ........................................................................... 1-1 1.1.2 DISTRESS button..................................................................................... 1-1 1.1.3 Diagnostics ............................................................................................... 1-1 1.1.4 Floppy disk drive, floppy disks .................................................................. 1-1 1.1.5 Audio alarm .............................................................................................. 1-2 1.2 Printer PP-510 (optional supply).......................................................................... 1-2 1.3 Keyboard............................................................................................................. 1-3 1.3.1 Key description ......................................................................................... 1-3 1.3.2 Shortcut keys............................................................................................ 1-5 1.4 Function Menus................................................................................................... 1-5 1.4.1 Choosing menu, menu options ................................................................. 1-6 1.4.2 Function menu description........................................................................ 1-6 1.4.3 Sample menu operation............................................................................ 1-7 1.5 Display Indications .............................................................................................. 1-8 1.6 Error Messages and Alerts ................................................................................ 1-10 1.7 Silencing the Audio Alarm...................................................................................1-11 2. SYSTEM INITIALIZATION.............................................................................2-1 2.1 System Settings .................................................................................................. 2-1 2.1.1 Connecting to main terminal ..................................................................... 2-1 2.1.2 System setup............................................................................................ 2-2 2.2 Terminal Setup .................................................................................................... 2-6 2.3 Login and Logout ................................................................................................ 2-8 2.3.1 Login......................................................................................................... 2-8 2.3.2 Logout..................................................................................................... 2-10 2.4 EGC Settings .....................................................................................................2-11 2.4.1 What is the EGC (Enhanced Group Call) service? ..................................2-11 2.4.2 EGC setup .............................................................................................. 2-12 2.4.3 Adding EGC channels ............................................................................ 2-15 2.4.4 Saving, printing EGC messages automatically ....................................... 2-16 2.5 Adding NCS Channels ...................................................................................... 2-17 iii TABLE OF CONTENTS 2.6 LES List ............................................................................................................. 2-18 2.6.1 Adding stations to the LES list................................................................. 2-18 2.6.2 Editing the LES list .................................................................................. 2-20 2.6.3 Printing the LES list................................................................................. 2-21 2.7 Station List ......................................................................................................... 2-22 2.7.1 Adding stations to the station list ............................................................. 2-22 2.7.2 Editing the station list .............................................................................. 2-25 2.7.3 Printing the station list ............................................................................. 2-25 2.8 Entering Own Ship’s Position............................................................................. 2-26 2.9 Setting Directories ............................................................................................. 2-27 2.10 E-mail Service List............................................................................................. 2-28 2.11 E-mail Setup...................................................................................................... 2-30 2.12 Network Setup ................................................................................................... 2-31 2.13 Automatic Mode Setup ...................................................................................... 2-33 2.14 Saving, Loading System Settings ....................................................................... 2-34 2.14.1 Saving system settings to a floppy disk................................................... 2-34 2.14.2 Loading system settings to the terminal unit............................................ 2-34 3. FILE OPERATIONS.......................................................................................3-1 3.1 Preparing Files.....................................................................................................3-1 3.1.1 Preparing a routine file ..............................................................................3-1 3.1.2 Preparing a confidential file .......................................................................3-2 3.1.3 Editor menu setup.....................................................................................3-3 3.1.4 Working with text.......................................................................................3-4 3.2 Saving Files .........................................................................................................3-7 3.2.1 Formatting a floppy disk ............................................................................3-7 3.2.2 Saving files................................................................................................3-8 3.3 Opening Files .................................................................................................... 3-10 3.3.1 Opening files ........................................................................................... 3-10 3.3.2 Switching between files..........................................................................