GOBO LED Light DS-1404A USER MANUAL !2 1. Introduction Thank you for purchasing our GOBO LED light. Please read these instructions carefully before operating to avoid any possible damage and accidents caused by misuse. The GOBO LED light has a hydrodynamic aluminum shell. One 10W white LED is used to create a bright light output. It draws low power and is low weight. Packing List - LED GOBO Light - User manual - Power cord 2. Safety Information - Please consult skilled service technicians for any repairs required - Always disconnect from the power source before setting up, moving and servicing - Avoid direct eye contact to the light when in operation - Make sure the power supply voltage is compatible with this light - Before installation, please check the light’s fasteners and mechanical structure is in good condition and not damaged - The light is designed for indoor use, below 40 degrees celsius - The fixture may be mounted in any position provided there is adequate room for ventilation. Make sure there are no flammable and explosive items within 0.5 meters. - Please ensure the ground is always connected !3 3. Dimensions and Specifications Voltage: AC100V/264 VAC Frequency: 47-63 Hz Power Consumption: 25 W Lamp: 10W white LED Beam Angle: 13 degrees Net Weight: 2 Kg IP Rating: IP20 Dimensions: ! www.EddyLight.com 1-800-914-3538 !4 4. GOBO Installation Unscrew the 2 knobs on the top of the projector and remove the piece from inside Place the GOBO in the center hole. Squeeze the ring and place it on top of the GOBO to ensure the GOBO stays in place. After the GOBO is placed in the correct orientation, place the GOBO holder back into the projector and screw it on. !5 5. Operation The easiest way to operate your projector is through the remote control. You can also use the buttons on the projector to go through the options. All of the options are set using a scale of 0-255. To set it to the number you desire, move UP or DOWN to that number and press ENTER. The light will turn off, then press ENTER again. R - Red light intensity (0 off, 1 dimmest, 255 brightest) G - Green light intensity (0 off, 1 dimmest, 255 brightest) B - Blue light intensity (0 off, 1 dimmest, 255 brightest) W - White light intensity (0 off, 1 dimmest, 255 brightest) SHUT - Strobe effect. 0 = no strobe effect. 1-255 different strobe pattern and speed GOBO - Rotation feature. 000 = off 1-100 = different positions 101-170 = different speeds of counterclockwise rotation 185 - 250 = different speeds of clockwise rotation NOTE: R, G, B options are only for color projector. You can mix different values of red, green and blue to create any color. Focus x x x x x IR To focus the projector, rotate the lens. Every time you adjust the 0 MENU 0 UP RoHS x x distance of the projector to the 0 DOWN MADE IN CHINA 0 ENTER projection surface, you will need to adjust the focus x x www.EddyLight.com 1-800-914-3538 !6 6. DMX Control Function 3CH 5CH VALUE FUNCTION CH1 CH1 0-255 Intensity 0-5 No strobe 6-20 Random burst strobe(slow to fast) 21-60 Normal strobe(slow to fast) 61-100 Electronic Sinewave(slow to fast) CH2 101-140 Random Strobe(slow to fast) 141-180 Opening pulse(slow to fast) 181-220 Closing pulse(slow to fast) 221-255 Electronic Squarewave(slow to fast) 0-100 0-360° 101-170 CW(slow to fast) CH3 CH3 171-180 Stop 181-250 CCW(slow to fast) 251-255 Stop 0-70 No effect 71-75 AUTO 1(W + GOBO CW) 76-80 AUTO 2(W↑,W↓ + GOBO CW) 81-85 AUTO 3(W + GOBO CCW) - CH4 86-90 CHASE 1 91-95 CHASE 2 96-100 CHASE 3 101-255 Reserved 0-10 Use the dimmer mode which menu has set up 11-20 Dimmer off 21-30 Dimmer 1 - CH5 31-40 Dimmer 2 41-50 Dimmer 3 51-60 Dimmer 4 61-254 Use the dimmer mode which menu has set up !7 7. Display Operation Instruction MENU access the menu or return to a previous menu option ENTER select the current menu option UP menu selection or parameter increments DOWN menu selection or parameters decrease Instructions： Master mode sends a DMX signal to all other LED light units connected via DMX. Slave mode receives the incoming DMX signal from the Master, using the values set by the Master unit.This allows for a large group of lights to be connected and controlled by only one light. For Master mode, press ENTER on the unit to display “*” on the LED display. When there is no “*” being displayed on the LED display, the light is set to Slave by default. www.EddyLight.com 1-800-914-3538 !8 Tab Level 1 Level 2 Level 3 Level 4 ADDR(Address) 001-512 STAT(Static W 0-255* control) SHUT 0-255* GOBO 0-255* CHMD(Channe SET(Set) 5CH l mode) 3CH DIM(Dimming OFF mode) DIM1 DIM2 DIM3 DIM4 DISY(Display ON(Perma set) nent on) 2MIN (2 minutes off) CALP(Calibrate 0-255 position) AUTO(Auto) AT01 RUN..* AT02 RUN..* AT03 RUN..* CHS1 RUN..* CHS2 RUN..* CHS3 RUN..* CHS1（Chase SC01（Sce PROG（Program） W 0-255 1） ne 1） . SHUT 0-255 . GOBO 0-255 . TIME 0-255(S) . WAIT 0-25.5(S) . USE YES/NO SC20（Sce . ne 20） CHS3（Chase 3） INFO（Information SOFT(Software Vx.x ） version) POW(Power 100%/80%/ reduction) 50% ST L（Setting LOAD(Load) YES/NO load) PR L（Program YES/NO load) SEND(Send) YES/NO !9 6.1 DMX Address Setting 1. Select the ADDR Menu by navigating to it and pressing ENTER. 2. Press the UP/DOWN buttons to navigate between channels 1 - 512. 3. Press ENTER to select your desired channel. 6.2 Static Setting 1. Select the STAT menu by navigating to it and pressing ENTER 2. Press the UP/DOWN buttons to select WHITE, SHUT, or GOBO. 3. Press the UP/DOWN buttons to set up the【0-255】numerical value. 4. Press the ENTER button to escape and save. 6.3 Channel Mode Setting 1. Select the SET menu by navigating to it and pressing ENTER 2. Select the CHMD menu by pressing ENTER 3. Press the UP/DOWN buttons to select 3CH or 5CH 4. Press the ENTER button to escape and save. 6.4 Dimming Mode Setting 1. Select the SET menu by navigating to it and pressing ENTER 2. Select the DIM menu by pressing ENTER 3. Press the UP/DOWN buttons to select OFF, DIM1, DIM2, DIM, 3 or DIM4 4. Press the ENTER button to escape and save. When off is selected there will be no delay dimming effect DIM1 is the slowest. DIM4 is the fastest. www.EddyLight.com 1-800-914-3538 !10 6.5 Display Setting 1. Select the SET menu by navigating to it and pressing ENTER 2. Select the DISY menu by pressing ENTER 3. Press the UP/DOWN buttons to select ON, 2MIN. 4. Press the ENTER button to escape and save. 6.6 Calibrating the GOBO to Original Position 1. Select the SET menu by navigating to it and pressing ENTER 2. Select the CALP menu by pressing ENTER 3. Press the UP/DOWN buttons to set up the 0-255 numerical value. 4. Press the ENTER button to escape and save. 6.7 Auto Run, Self-Program 1. Select the AUTO menu by navigating to it and pressing ENTER 2. Press the UP/DOWN buttons to select AT01, AT02,AT03, CHS1, CHS2, CHS3 3. Press the ENTER button to escape and save. !11 6.8 Edit Self-Program 1. Select the PROG menu by navigating to it and pressing ENTER 2. Press the UP/DOWN buttons to select CHS1, CHS2, or CHS3 3. Press the ENTER button for confirmation and enter to the next menu. 4. Press the UP/DOWN buttons to select from SC1-SC20 5. Press the ENTER button for confirmation and enter to the next menu. 6. Press the UP/DOWN buttons to select W, GOBO, TIME, WAIT, USE, or SHUT 7. Press the UP/DOWN buttons to set the parameter which are needed. 8. Press the ENTER button to escape and save. When USE is set to NO，or the parameter of TIME is 0, it will not run this scene. When WAIT is set to be FADE time, the running process is as the following chart showing. 6.9 Checking Lighting Information 1. Select the INFO menu by navigating to it and pressing ENTER 2. SOFT is for software version information. 3. POW is for the current information of power reduction. 100% is the normal output. Projector will reduce to 80% or 50% output to protect from over-heating. www.EddyLight.com 1-800-914-3538 !12 6.10 Lighting Setting Parameter Reset 1. Select the LOAD menu by navigating to it and pressing ENTER 2. Select the ST L menu by navigating to it and pressing ENTER 3. Press the UP/DOWN buttons to select YES or NO. 4. Press the ENTER button to escape and save. ADDR, CALP and “PROG” are not reset, the others reset to the underlined value of the word. 6.11 PROG: SELF-PROGRAMMING PARAMETER RESET 1. Select the LOAD menu by navigating to it and pressing ENTER 2. Select the PR L menu by navigating to it and pressing ENTER 3.