easymotoculture easymotoculture Fill fuel tank * Use anyautomotive gasoline. Fuel ffiler cap easymotocultureCAUTION: Gasolinesubstitutes are not recommended, they may be harmful to the fuel system components. Recoil starter Check cleaner fordirt orobstruction of ele- ructionof ele- ments. Check reduction gear oil level. Fill with SE rated SAElOW-40 engine oil if necessary. easymotoculture Turn the fuel valve ON. Turn the en-@ne switch ON. Loosenthe wing nutand raise the throttle lever slightly. Move the throttlelever cdown fully. Close choke lever. Turn the fuel valve OFF. b Set the throttle by tightening the wing nut at the desired speed. Turn the engine switch OFF. NOTE: Donot use thechoke if the engine is warm or the air temperature 1s high. First 20 Hrs. operating Every 50 Hr'S. operating CLEAN AIRCLEANER ELEMENT I Clean more frequently if operating in I CHANGE ENGINE OIL ANLmDUCI'IONGEAROIL I a dusty area. *Remove dust from paper element "B" B by applying compressed air from inside of theelement or tapping the case lightly. If the element is excessively easymotoculture dirty replace or wash it in liquid detergent and water and flush until water isclear. Dryit thoroughly by applying compressed air before install- Ing. * Wash part "A" (element) in clean- *Wash the foam element in "C" liquid ing solvent. After drying, soak in detergent and water and flush until water is clear. Dry itthoroughly by .~ oil and squeeze out the excess. applying compressed air. After drying, ~ with a lever. - soak in oil and saueeze out the excess. Every 100 Hrs. operating CLEAN SPARK PLUG AND CHECK GAP CHANGE ENGINEOIL CLEANSTRAINER FUEL D 0.6 - 0.7 mm *Wash removed parts (.024 - .028 in) in solvent, dry them 0.. Use NGK B4H, BR4HS or :. ' '. .-> thoroughlyandin- ND W14F-U, W14FR-U , stall securely.Turn I . CDI type .- ._. thefuel valve ON and check for leaks. 0.9 - 1.0 mm t Wash "D" and "E" in cleaning (.035 - .039 in) solvent. After drying, refillwith Use NGK BP4HS-IO clean en-he oil upto oil level BPR4HS-10 or, ND W 14FP- mark. ULIO, W14FPR-ULIO Every 300 Hrs. operating Check fuel line for cracks or leaks. Replace, * Do not use gasoline or low flash point solvents for cleaning. They are flammable and * explosive under certain conditions. if necessary. ADJUST IGNITION TIMING ADJUST VALVECLEARANCE ADJUST CARBURETOR SCREWS t Measure at TDC on compressionstroke t Startthe engine and adjust idle speed by CarDuretor with pilot "Iew f Adjust contact breaker points so thatthey 1) Tighten the pilot screw untilit bottoms just start to open when the "F" mark on the whenthrottle'stop engine theturning is cold. Screw. lightly, then back it off the number of turns flywheel aligns with the mark on crankcase. STANDARD: shown below: t IGNITION TIMING: 20 BTDC. IN 0.08 - 0.16 n LO03 - ,006 in) 0.11 - 0.19 mm LO04 - ,007 in) G300 I,"% turns EX G400 2 turns t If the clearance is less thanthe standard 2) Adjust idle speed as outlined at left. limit, grind valve stem or replace valve. THROTTLE STOPSCREW CONTACT BREAKER ASSY does not require adjustme? require notThe CDI Type does MAI~JET -- wire end. easymotoculture ~~ ~ ~~ Cycle, valve arrangement 4 cycle, side valve Displacement cc (cu in) 1 272 (16.61 I 406 (24.8) Max. output hp/rpm I 7/3,600 I 10/3,600 Max. torque kg-m (ft-lb) 1 1.5 (11) 1 2.3 (16.6’1 Solid wire core Fuel consumptiongjhp-h(lb/hp-h) 285 (0.62) 270 (17) mounting I 1 PTO shaft rotation Counterclockwise Dry weight kg Ob) 1 22 (49) I 33 (72.8) A return spring and wire end may be used with a flexible core cable. I ALL INFORMATION, ILLUSTRATIONS, DIREC- TIONSAND SPECIFICATIONS INCLUDED IN THIS PUBLICATIONARE BASED ON THE LATEST Flexible wire core mounting PRODUCT INFORMATION AVAILABLE AT THE TIME OF APPROVAL FOR PRINTING. HONDA MOTORCO., LTD. RESERVES THE RIGHT TO MAKE CHANGES AT ANY TIME WITHOUT NOTICE AM) WITHOUT INCURRING ANY OBLIGATION WHATEVER. NO PART OF THIS PUBLICATION MAY BE RE- PRODUCEDWITHOUT WRITTEN PERMISSION. PROPERTY OF SERVICE COMllClUNICATIONS. ’* DO NOT REMOVE. (AH) 31 88900 Current customer service contact information: Servicing dealership personnel are trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager, General Manager, or Owner can help. Almost all problems are solved in this way. Unitedeasymotoculture States, Puerto Rico, and U.S. Virgin Islands: If you are dissatisfied with the decision made by the dealership's management, contact the Honda Regional Engine Distributor for your area (www.honda-engines.com/dea.htm). If you are still dissatisfied after speaking with the Regional Engine Distributor, you may contact the Honda Office as shown. American Honda Motor Co., Inc. Power Equipment Division Customer Relations Office 4900 Marconi Drive Alpharetta, GA 30005-8847 Or telephone: (770) 497-6400 M-F, 8:30 am - 7:00 pm EST When you write or call, please provide the following information: • Equipment manufacturer's name and model number that the engine is mounted on • Engine model, serial number, and type • Name of the dealer who sold the engine to you • Name, address, and contact person of the dealer who services your engine • Date of purchase • Your name, address, and telephone number • A detailed description of the problem .