1 An Analytical Approach to Broadband Matching David Sobel, Johan Vanderhaegen Abstract— The purpose of this project is to study differ- ent broadband matching techniques for microwave ampli- fiers. Two different methodologies for broadband amplifier design are developed and employed. The first method in- volves the design of a 6 dB/octave roll-up filter to com- pensate for the 6 dB/octave roll-off inherent to the active device. The second method seeks a closed form solution to the gain-matching problem with the use of second order matching networks. For each technique a two-octave gain- compensated amplifier is designed. I. Introduction HE ideal microwave amplifier would have constant Tgain and good input matching over the desired fre- Fig. 1. Broadband matching problem. quency bandwidth. Conjugate matching will give maxi- mum gain at the center of the band but results in unpre- dictable bandwidth and ripple. Another problem is the method is the use of two element matching networks. 6 dB/octave roll-off of S . Some of the common ap- 21 II. Network synthesis of sloped bandpass filters proaches to this problem| are| listed below[1] ; in each case an improvement in bandwidth is achieved only at the ex- This theory[2] assumes the transistor to be unilateral, pense of gain, complexity or other factors. so that the input and output networks can be designed seperately. In order to determine whether a transistor can A. Commonly used broadband techniques be considered unilateral from the standpoint of transducer Compensated matching networks: Input and output net- power gain, the unilateral figure of merit u can be used : • works can be designed to compensate for the gain roll-off in S21 , but generally at the expense of the input and output S S S S | | u = 11 22 12 21 (1) match. | | | 2 | | | | |2 Resistive matching networks: Good input and output 1 S11 1 S22 • − | | − | | matching can be obtained by using resitive matching net- If the transistor can be considered as unilateral, the in- works, with a corresponding loss in gain and increase in put can be approximated by a series RC-network and the noise figure. output by a parallel RC-network. In the case of discrete Negative feedback: Negative feedback can be used to flat- • transistor, inductors representing leads have to be added. ten the gain response of the transistor, improve the input and output match, and improve the stability of the device. A. General lumped broadband matching theory Amplifier bandwidths in excess of a decade are possible with this method, at the expense of gain and noise figure. Consider the broadband matching problem in figure 1, Balanced amplifiers: Two amplifer having 90◦ couples where N denotes a passive lossless matching network that • at their input and output can provide good matching over has to match ZL to R. Then an octave bandwidth, or more. The gain is equal to that 2 2 2 2 G(ω ) = S21(jω) = 1 S11(jω) = 1 S22(jω) of a single amplifier, however, and the design requires two | | − | | − | | transistors and twice the DC power. (2) Distributed amplifiers: Several transistors are cascaded • or (using analytic continuation) together along a transmission line, giving good gain, and 2 2 G( s ) = 1 S22(s) (3) noise figure over a wide bandwidth. The circuit is large, − − | | and does not give as much gain as a cascade amplifier with One can prove[2] that the same number of stages. Z2(s) ZL( s) B. This project S22(s) = − − (4) Z2(s) + ZL(s) The purpose of this project is to study different method- ologies to design matching networks that compensate for The poles of S22(s) in the right half plane are the poles of the 6 dB/octave roll-off of S21 . One method consists of ZL( s), since the other terms in equation (4) are positive- network synthesis of a sloped| bandpass| filter, i.e. a filter real− and cannot have poles in the right half-plane. Let with a 6 dB/octave roll-up over the passband. The second si (i = 1, 2, . , m) denote the the poles of ZL( s) (real − 2 or complex conjugate pairs). Define B(s) as low frequency 2 GHz high frequency 8 GHz m s si ripple 1 dB B(s) = − (5) Y s + s filter order 2 i=1 i TABLE I Then B(s) has only poles in the left half-plane, is real for Broadband amplifier specifications. real s and B(s)B( s) = 1 (B(s) is an all-pass function). Define then ρ(s) as− ρ(s) = B(s)S22(s) (6) would perform matching and 6 dB/octave roll-up at the same time. G(ω2) can be specified as : This reflection coefficient ρ(s) has only poles in the left 2 half-plane. Substituting equation (6) in equations (3) and 2 Kn (f/fc) G((2πf) ) = · 2 (14) (4) yields 2 f f f0 1 + ε Cn B f0 − f 2rL(s)B(s) Z2(s) = ZL(s) (7) f0 is the center frequency, B is the bandwidth. The B(s) ρ(s) − 2 − maximum ripple is given by 1/(1 + ε ). Kn and fc are ZL(s) + ZL( s) proportionality constants so that 0 G(ω2) 1 for all rL(s) = − (8) ≤ ≤ 2 frequencies. Cn(x) are the Chebychev polynomials of the ρ(jω) 2 = 1 G(ω2) (9) first kind : | | − 2 For ρ(s) to be real, it is necessary that 0 G(ω ) 1. T0(x) = 1 (15) Once G(ω2) is given, ρ(s) can be determined≤ by spectral≤ T1(x) = x (16) factorisation (and using analytic continuation) : 2 T2(x) = 2x 1 (17) 2 − 2 N(s ) ρ(s)ρ( s) = 1 G( s ) = 2 (10) The equivalent input network of the transistor consists − − − M(s ) of a series RC-network. This means that, using the termi- nology of section II-A, N(s2) and M(s2) are respectively the numerator and the 2 denominator of G(s ), and they both can be decomposed 1 1 + sRCi as : ZL = Ri + = (18) sCi Ci N(s2) = n(s)n( s) (11) For the EE217 transistor at high frequencies : − M(s2) = m(s)m( s) (12) − Ri = RI + RS = 11.25 Ω (19) These n(s) and m(s) are formed by the left half-plane Ci = CGS = 0.31 pF (20) zeros of respectively N(s) and M(s). Therefore : Using the specifications in table I and going through the n(s) steps described in section II-A, Z2(s) turns out to be : ρ(s) = (13) ±m(s) 2s4 + 2.71s3 + 8.75s2 + 3.16s + 2 Z2(s) = (21) So, given G(ω2), ρ(s) can be determined by spectral fac- 0.630s3 + 0.283s2 + 0.179s torisation. If also Z (s) is given, then Z (s) can be deter- 11.2 1 L 2 = 3.17s + + (22) mined by using equation (8). Under certain conditions[2] s 0.156 1 for ρ(s), a passive network can be derived that implements s + 1.82 s + 2.87 Z2(s). This is a second order chebychev bandpass filter with a B. Input lossless matching 6 dB/octave roll-up over the passband. All the numbers Examining the unilateral figure of merit u for the EE217 are normalized to a center pulsation ω0 of 1 rad/s. The transistor (figure 6), this transistor can be considered corresponding ciruit is given in figure 2 and the element highly non-unilateral (or bilateral). This means first of all values are given in table II. Note that CGS fullfills the that there is a risk of making the transistor unstable. Fur- function of C1, R1 is the input resistance Ri of the transis- thermore the input and ouput matching networks cannot tor. R2 is the source resistance. be designed independently. The input matching network expects a source resistance The reason that u is so high for this transistor, is that R2 of 32.3 Ω. This can be converted to 50 Ω by an ideal S11 is so close to 1. This also means that we can get a transformer. The ideal transformer can be removed by in- considerable gain from the input network. Taking all this troducing an extra element (L2) and changing the other into account, we decided to add only an input match, that element values. Table III gives the final input matching 3 (a) (b) Fig. 2. Second order chebychev bandpass filter with a 6 dB/octave Fig. 3. General form of a 2-element L-match (a) and π-match (b) roll-up over the passband. networks. C1 310 fF L1 1.42 nH L12 2.86 nH C2 1.95 pF L2 0 nH R2 32.3 Ω TABLE II Broadband matching network. (a) (b) network. This network can be obtained by equating the Z-matrix of the network in table II with an ideal trans- Fig. 4. Acheivable impedances of two inductor L-match (a) and former and the Z-matrix of a similar network without an CL π-match (b). The shaded regions correspond to unattainable impedances. ideal transformer but with an additional inductor L2. The final circuit, including the transistor, is shows in figure 7. Figure 8 shows the simulated results this circuit to provide exact gain compensation at the band edges; a and confirms the specifications given in table I. byproduct of this process is a flattened gain response over the bandwidth of interest. C. Conclusion A. Topology Selection Network synthesis of sloped bandpass filters is an inter- esting technique to compensate for the 6 dB/octave roll- The circuit topology used in the mathematical derivation off of the transistor.