Voip V2 Loudspeaker Amplifier the IP Endpoint Company

Voip V2 Loudspeaker Amplifier the IP Endpoint Company

Now with up to 25 watts output (802.3at) VoIP V2 Loudspeaker Amplifier The IP Endpoint Company The new CyberData V2 SIP-enabled VoIP Loudspeaker Amplifier provides an easy method for implementing an IP-based overhead paging system for both new and legacy installations. With up to 25 watts of driving power (802.3at), the Amplifier provides direct drive of a standard Horn speaker and supports a line-out connector for connection to an external amplifier. The interface is compatible with most SIP-based IP PBX servers that comply with the SIP RFC 3261. For non-SIP environments, the Loudspeaker Amplifier can be configured to Loudspeaker (part #011068) must be purchased separately. listen to multicast address and port number combinations to Specifications form paging zones. Ethernet I/F 10/100 Mbps Ringer Mode Power Input PoE 802.3at or 802.3af o o o o The VoIP V2 Loudspeaker Amplifier supports two SIP Operating Temperature -10 C to 50 C (14 F to 122 F) extensions. One extension can be assigned to a page group for Protocol SIP RFC 3261 Payload Types G711 auto answer paging. The second extension can be assigned to a “First-to-Answer” ring group with IP phones. An audio ring file Warranty 2 Years Limited is activated when the second SIP extension of the ceiling Dimensions 14" x 10" x 4" speaker is dialed. If any of the IP phones in the ring group is Output 802.3af - up to 8 watts answered (or if the caller hangs up), the Loudspeaker Amplifier 802.3at - up to 25 watts stops ringing. Line In: Features Input Signal Amplitudes 2.0 VPP maximum Input Impedance 10k Ohm SIP and Simultaneous Multicast Dual-speed ethernet 10/100 Mbps Line Out: Web-based configuration Output Signal Amplitudes 2.0 VPP maximum Output Level +2dBm nominal PoE 802.3at and 802.3af-enabled Total Harmonic Distortion 0.5% maximum Output Impedance 10k Ohm Line-in for background music Boxed Weight 6.5 lbs. Line-out connector Part Number DTMF controlled relay Loudspeaker Amplifier, AC 011095 Direct 8 Ohm speaker drive Loudspeaker Amplifier, PoE 011097 Loudspeaker Part Number 011068 User-uploadable tones and messages Digital and manual volume control Second SIP endpoint "Night Ringer" Autoprovisioning Auto-call voice message from input port sense The IP Endpoint Company CyberData Corporation 3 Justin Court, Monterey, CA 93940 831.373.2601 Fax: 831.373.4193 www.cyberdata.net VoIP V2 LoudspeakerAmplifier Typical Installation - AC Version (Part# 011095) Generic Ethernet Switch 1 2 3 4 5 6 011095 VoIP V2 Loudspeaker Amplifiers – AC Required IP Phone IP-PBX Server High Power PoE Injector in Box Typical Installation - PoE 802.3af (Part# 011097) 802.3af Generic PoE Switch or 802.3at High Power Switch 1 2 3 4 5 6 011097 VoIP V2 Loudspeaker Amplifiers – No AC Required IP Phone IP-PBX Server CyberData Corporation 3 Justin Court, Monterey, CA 93940 831.373.2601 Fax: 831.373.4193 www.cyberdata.net 930340I/130422 VoIP V2LoudspeakerAmplifier Alert Strobe also beplayedtothephone. Audio messagewill answers, thestored pre-set phonenumberandwhenthat Amplifier canalsocalla The Loudspeaker repeat untiltheconditioniscleared. Audio filewillplayoutthelocalspeakerand When the“Sense-In”isactivated,stored to the Loudspeaker Amplifier. Amplifier. to theLoudspeaker User canuploadanaudiomessage CyberData Corporation CyberData Power Source AC orDC Configuring the V2 Loudspeaker Amplifier for Alarm Sensing Amplifierfor V2 Loudspeaker Configuring the 3 Justin Court, Monterey, CA 93940 Court, Monterey, 3Justin OUT Controlled Device Depending Upon Output Contacts AC orDCrated V Requirements V Mechanical Solid State 2 2 Relay or Loudspeaker Amplifier Loudspeaker AmplifierConnections 1-Sense (+) IN High PIVUltraFast Switching Diode C 2-GND to the“Sense-In”connection. Window Reedswitchisconnected L 3-Relay COM A S - 4-Relay NO S ( ) I POWER SUPPLY 30 VDC@1A I 831.373.2601 5-Line-In(+) W MAX. DC 6-Line-In(-) I R I w 7-Line-Out(+) N i G + t h Fax: 831.373.4193 Fax: 8-Line-Out(-) Strobe Alert 9-Spkr Out(+) Loudspeaker Amplifier blink and drive an Alert Strobe. blink anddrivean amplifier canbeprogrammedto phone, therelayonpaging Amplifier iscalledfromaremote When theV2Loudspeaker 10-Spkr Out (-) ReedSwitch Window IP Phone www.cyberdata.net.

View Full Text

Details

  • File Type
    pdf
  • Upload Time
    -
  • Content Languages
    English
  • Upload User
    Anonymous/Not logged-in
  • File Pages
    3 Page
  • File Size
    -

Download

Channel Download Status
Express Download Enable

Copyright

We respect the copyrights and intellectual property rights of all users. All uploaded documents are either original works of the uploader or authorized works of the rightful owners.

  • Not to be reproduced or distributed without explicit permission.
  • Not used for commercial purposes outside of approved use cases.
  • Not used to infringe on the rights of the original creators.
  • If you believe any content infringes your copyright, please contact us immediately.

Support

For help with questions, suggestions, or problems, please contact us