TL-2020 PE ACCESSORY BOX INSTRUCTION MANUAL ❾ ❶ ❸ ❹ ❷ ❽ ❺ ❼ ❻ Accessory box No. 1 Accessory box No. 2 Accessory bag ❶ 1/5" Quilting Foot ❻ 1/4" Presser Foot Even Feed Foot ❷ 1/4" Quilting Foot ❼ Compensating Foot (Right 1/4") ❸ Quilting Foot Front Open Toe ❽ Hemming Foot ❹ 1/4" Quilting Foot (for Ruler) ❾ Zipper Attaching Foot ❺ Echo Quilting Foot Quilt Guide for Even Feed Foot Changing the presser foot CAUTION: Turn OFF the power switch when replacing the presser foot. 1 Turn off power and remove the presser foot. Install the presser foot. Presser 2 Screw in the foot presser foot Accessory box No. 1 ❶ 1/5" Quilting Foot This quilting foot is convenient for free motion quilting, quilting along with ❷ 1/4" Quilting Foot the pattern, free-hand embroidery, etc. ❸ Quilting Foot Front Open Toe ● 1/5 inch = ● 1/4 inch = ● Front open type 5.0 mm type 6.5 mm type This type is suited for This type is suited This type is suit- free-motion quilting. 1/4 inch for free-motion 1/5 inch ed as a guide for The needle entry point 1/5 inch quilting in general. (5.0 mm) sewing stitches (6.5 mm) (5.0 mm) is easily observed at regular inter- since the front section vals. 1/8 inch 1/8 inch 1/8 inch (3.2 mm) is open. (3.2 mm) (3.2 mm) Install the Position Feed Dog in lower Position stitch length Lower the foot and 1 quilting foot. 2 position. 3 adjusting dial ”0”. 4 start sewing. Needle clamp screw Plate Presser bar Screw in the presser foot Put the plate on the needle clamp Rotate presser foot pres- screw, insert the installing portion into sure regulator until blue the presser bar, and securely tighten bar in pressure indication the screw in the presser foot. window is at top. - 1 - ❹ 1/4" Quilting Foot (for Ruler) This quilting foot is useful for free-motion quilting while guiding the material along with the ruler. Install the quilting Position Feed Dog in lower Position stitch length 1 foot. 2 position. 3 adjusting dial ”0”. 4 ❶ ❷ Rotate presser foot pressure Place the material under the quilt- regulator until blue bar in pres- ing foot. Lower the quilting foot. sure indication window is at Adjust the quilting foot height with top. screw ❶ in accordance with the material thickness. Put ruler ❷ on the material. Carry out quilting while guiding the material so that the quilting foot is always posi- tioned along the ruler. ❺ Echo Quilting Foot This quilting foot is useful for free-motion echo quilting. CAUTION: Be sure to carefully lower the presser foot since it can be broken if it is lowered abruptly. Assemble the echo quilting Install the echo quilting Position Feed Dog in lower 1 foot. 2 foot. 3 position. ❶ Detach screw ❶ that is temporarily secured to the holder. Insert the Position stitch length holder into the presser foot. 4 adjusting dial ”0”. 5 Tighten screw ❶ . * Once you have assembled the ❷ Echo quilting foot, it cannot be stored in the accessory box. If you want to store the Echo quilting foot in the accessory box, ❸ it is necessary to disassemble it into the holder and the presser foot. Rotate presser foot pressure Place the material under the quilting foot. Lower the regulator until blue bar in pres- quilting foot. Adjust the quilting foot height with screw ❷ sure indication window is at in accordance with the material thickness. Sew echo line top. ❸ using the red line on the quilting foot that the quilting foot is always positioned along the ruler. - 2 - Accessory box No. 2 ❼ Compensating Foot ❻ 1/4" Presser Foot (Right 1/4") 1/4" 1/4" Guide Guide Sew the material while aligning its edge Sew the material while aligning its edge with the guide. with the guide. Stitches can be sewn at the position Stitches can be sewn at the position which is 1/4" away from the guide. which is 1/4" away from the guide. ❽ Hemming Foot Cut the corner of the mate- Fit the trimmed material edge into the Hem the material edge while helping the 1 rial. 2 vortex groove in the hemming foot. 3 material to go into the groove by hand. 5 mm 8 mm Material Trim the corner part of the materi- Fit the material into the vortex groove in Draw the needle and bobbin thread ends with your al to help make the hemming foot the hemming foot until the descended left hand, turn the handwheel by 3 or 4 rotations hem the material edge. needle reaches the material, and lower the until you are sure that the material edge is rolled hemming holder. into the groove. Then hem the material edge while pinching the ma- terial edge with your right-hand thumb and index finger to make sure that the appropriate amount of material is fed into the hemming foot with consis- tency. ❾ Zipper Attaching Foot Turn the presser position selector screw to move Install a zipper attaching the presser foot until the correct needle entry 1 foot. 2 point is obtained. 3 Presser position selector screw Presser bar Screw in the presser foot Loosen the screw in the presser When sewing the left-hand side of the zipper, move the foot, and attach the zipper attach- presser to the left. When sewing the right-hand side of it, ing foot from the far side of the move the presser to the right. presser foot. - 3 - Quilt Guide for Even Feed Foot Stitches can be sewn at regular intervals using the walking foot. * Use the sewing machine at medium speed. 1 Check the relevant parts. 2 Assembling and installing the stitch ruler. Remove walking foot setscrew which fixes the walking foot. C A Aligning the mounting B sections of the stitch D ruler and walking foot A Stitch guide bar × 1 with each other, securely B Stitch guide base × 1 tighten the walking foot C Stitch guide × 1 D setscrew D. D Screw × 1 (Example: In the case of guiding the material so that it is kept Carry our sewing using 3 Adjusting the guide position. 1 cm away from the needle position) 4 the guide as reference. In the case of setting the guide on In the case of setting the guide on the right side of needle the left side of needle ❸ ❸ ❹ The interval of ❹ B A A B scale marks on the guide bar is 5 mm. C C ❶ ❷ Stitches can be sewn while keeping the regular stitch intervals. 1 cm 1 cm ① Aligning the leftmost scale mark ① Aligning the rightmost scale mark on guide bar A with the left edge Remove setscrew ❶ . on guide bar A with the right edge of guide base B, tighten setscrew The stitch ruler can of guide base B, tighten setscrew ❸ . be used on both the ❸ . ② Aligning guide C with the first right and left sides by ② Aligning guide C with the second scale mark from the right edge of changing the mounting scale mark from the left edge of guide base B, tighten setscrew position of guide sec- guide base B, tighten setscrew ❹. ❹ . The distance from the needle tion ❷ from right to left The distance from the needle posi- position to the guide is 1 cm. or left to right. tion to the guide is 1 cm. Adjust the guide position referring to the needle position and positional relation between the bar scale and guide. Securely tighten the setscrew. Accessory bag Even Feed Foot Generally, this presser foot is used for hard-to-feed or for difficult-to-feed materials such as velvet, jersey, vinyl, cloth artificial leather, leather, etc. This smoothly feeds the material and prevents the material from slipping. Turn the presser foot pressure regulator to set 1 Install the even feed foot. 2 the presser foot pressure to “low”. Needle clamp Increase Decrease Screw in the screw presser foot Turn to to decrease the Actuating presser foot lever pressure. Fit forked portion of the actuating lever Set the pressure to “lowest” when sewing the velvet to the needle clamp, insert the installing material. portion into the presser bar, and securely Use the sewing machine at medium speed. tighten the screw in the presser foot. 40246462 - 4 -.