10mm - 24mm Deep PSU Automotive Punches: 3", 6", 12" Extensions Center Service Required Tool Flex Handle (Breaker Bar) Brass Drift List Ratchet Pin 1/8", 3/16", 1/4", 5/16 " Spark Plug (Gap Tool) Taper 3/8", 1/2", 5/8" Tape Measure – Standard Air Blow Gun (meeting OSHA Safety Glasses (meeting and Metric requirements) OSHA requirements) Test Light (12V) Allen (Wrench or Socket) Set Scraper: - Standard (.050" - 3/8") Carbon 1" Tire Pressure Gauge Torque Wrench: Allen (Wrench or Socket) Set Gasket 1" 3/8" Drive (10 - 250 lb. in.) - Metric (2mm - 7mm, Screwdriver - Blade Type: 3/8" Drive (5 - 75 lb. ft.) 10mm, 12mm) Stubby Battery Post Cleaner 6", 9", 12" 1/2" Drive (50 - 250 lb. ft.) Battery Terminal Pliers Offset Torx Set (screwdrivers Battery Terminal Puller and/or sockets): Chisels: T-8 to T-60 Cape 5/16" Screwdriver - Phillips: Snap On 525 DVOM Cold 3/8", 3/4" Stubby #1, #2 required for meter Chisel Holder 6" #1, #2 certification (Multimeter Claw Type Pickup Tool 12" #3 preferred) Offset #2 Dial Indicator w/Vice Grip Screwdriver - Impact Driver Tool Chest (Must be able to Combination Wrenches: Set roll and lock) Standard (1/4" – 1 1/4") Metric (7mm - 24mm) Crowfoot Wrench Set - Metric Screw Starter: Suggested but not Crowfoot Wrench Set - Phillips required on the first Standard Standard day of school: Ear Protection Feeler Gauge (Blade Type): Bolt/Screw Extractor Kit .002" - .040" Logic Probe .006mm - .070mm Compression Gauge Socket Set - 1/4" Drive: Vacuum gauge 1/4" - 1/2" Standard Depth Hand Vacuum Pump Files: 1/4" - 1/2" Deep Fuel Pressure Gauge Coarse 6" and 12" 6mm - 12mm Standard Dial Calipers Fine 6" and 12" Depth ½ Electric Drill w/ Drill Index Half Round 12" 6mm - 12mm Deep ½ Air Impact Round 6" and 12" Flex/Universal Type 3/8 Air Impact Flare Nut (tubing) Wrenches: 3", 6" Extensions 3/8 Air Ratchet 3/8" - 3/4" Ratchet Remote hose clamp pliers 10mm - 17mm Air operated die grinder with Flashlight Socket Set - 3/8" Drive: 3m pad attachments Fuse Puller 5/16" - 3/4" Standard Depth Coolant Pressure Tester Fused Jumper Wire Set (with (6 point) Air Operated Chisel w/ tie rod various adapters) 3/8" - 3/4" Deep (6 point) Hack Saw attachment 10mm - 19mm Standard Magnetic Tool Tray Depth DVOM Inductive Clamp Hammers: 10mm - 19mm Deep 16 oz. Ball Peen 3", 5", 10" Extensions Brass Flexhead Ratchet Dead Blow Plastic Mallet Ratchet Plastic Tip Spark Plug Sockets 5/8", Rubber Mallet 13/16" Inspection Mirror Speed Handle Magnetic Pickup Tool Universal Joint Flexible Socket Set 3/8" - Pliers: 3/4" Combination 6" Flexible Socket Set 10mm - Hose Clamp 19mm Locking Jaw Needle Nose 6" Socket Set - 1/2" Drive: Side Cutting 7/16" - 1 1/8" Standard Slip Joint (Water Pump) Depth Pry Bars: 7/16" - 1 1/8" Deep Rolling Head 10mm - 24mm Standard Straight Depth Rev 3/25/21 .