<^£mi-(2ondacto\ FELEPHONE: (973) 376-2922 20 STERN AVE. SPRINGFIELD, NEW JERSEY 07081 (212)227-6005 FAX: (973) 376-8960 U.S.A. Programmable Unijunction Transistor Programmable Unijunction Transistor Triggers Designed to enable the engineer to "program" unijunctioi characteristics such as RBB> T). IV an^ I? by merely selecting two resistor values. Application includes thyristor-trigger, oscillator, pulse PUTS and timing circuits. These devices may also be used in special thyristor applications due to the availability of an anode gate. Supplied in an 40 VOLTS inexpensive TO-92 plastic package for high-volume requirements, 300 mW this package is readily adaptable for use in automatic insertion equipment. • Programmable — RBB> *!> IV ar>d Ip • Low On-State Voltage — 1.5 Volts Maximum (2> IF = 50 mA AO- -OK • Low Gate to Anode Leakage Current — 10 nA Maximum • High Peak Output Voltage — 11 Volts Typical • Low Offset Voltage — 0.35 Volt Typical (Ro = 10 k ohms) • Device Marking: Logo, Device Type, e.g., 2N6027, Date Code MAXIMUM RATINGS (Tj = 25°C unless otherwise noted) Rating Symbol Value Unit "Power Dissipation PF 300 mW Derate Above 25°C 1/ejA 4.0 mW/'C *DC Forward Anode Current IT 150 mA TO-92 Derate Above 25°C 2.67 mA/°C *DC Gate Current IG ±50 mA Repetitive Peak Forward Current 'TRM Amps PIN ASSIGNMENT 100 us Pulse Width, 1% Duty Cycle 1.0 1 Anode •20 us Pulse Width, 1 % Duty Cycle 2.0 2 Gate Non-Repetitive Peak Forward Current 'TSM 5.0 Amps 10 us Pulse Width 3 Cathode 'Gate to Cathode Forward Voltage VGKF 40 Volts •Gate to Cathode Reverse Voltage VGKR -5.0 Volts 'Gate to Anode Reverse Voltage VGAR 40 Volts 'Anode to Cathode VoltageC1) VAK ±40 Volts Operating Junction Temperature Range TJ -50 to °C •MOO 'Storage Temperature Range Tstg -55 to C + 150 'Indicates JEDEC Registered Data (1) Anode positive, RQA = 1000 ohms Anode negative, RQA = °Pen NJ Semi-Conductors reserves the right to change test conditions, parameters limits and package dimensions without notice information rumished by NJ Semi-Conductors is believed to be both accurate and reliable at the time of going to press. However NJ Semi-Conductors assumes no responsibility for any errors or omissions discovered in its use. NJ Semi-Conductors encourages customers to verify that datasheets are current before placing orders. Quality Semi-Conductors 2N6027, 2N6028 THERMAL CHARACTERISTICS Characteristic Symbol Max Unit Thermal Resistance, Junction to Case RftJC 75 'C/W Thermal Resistance, Junction to Ambient ROJA 200 'C/W Maximum Lead Temperature for Soldering Purposes TL 260 c (< 1/16" from case, 10 sees max) ELECTRICAL CHARACTERISTICS (Tc = 25°C unless otherwise noted.) Characteristic Fig. No. Symbol Min Typ Max Unit *Peak Current 2,9,11 IP HA (VS = 1 0 Vdc, RQ = 1 MCi) 2N6027 — 1.25 2.0 2N6028 __ 0.08 0.15 (Vs = 10Vdc, RG = 10k ohms) 2N6027 — 4.0 5.0 2N6028 — 0.70 1.0 'Offset Voltage 1 VT Volts (VS = 10 Vdc, RG = 1 MQ) 2N6027 0.2 0.70 1.6 2N6028 0.2 0.50 0.6 (Vs = 10 Vdc, RG = 10 k ohms) (Both Types) 0.2 0.35 0.6 "Valley Current 1,4,5 iv MA (VS = 10 Vdc, RG = 1 MH) 2N6027 — 18 50 2N6028 — 18 25 (VS = 10 Vdc, RG = 10 k ohms) 2N6027 70 150 — 2N6028 25 150 — (VS = 1 0 Vdc, RG = 200 ohms) 2N6027 1.5 — — mA 2N6028 1.0 — — 'Gate to Anode Leakage Current — 'GAO nAdc (Vs = 40 Vdc, TA = 25°C, Cathode Open) — 1.0 10 (Vs = 40 Vdc, TA = 75°C, Cathode Open) — 3.0 — __ Gate to Cathode Leakage Current — IGKS 5.0 50 nAdc (VS = 40 Vdc, Anode to Cathode Shorted) 'Forward Voltage (Ip = 50 mA Peak)0) 1,6 VF — 0.8 1.5 Volts *Peak Output Voltage 3,7 V0 6.0 11 — Volt (VG = 20 Vdc, GC = 0.2 |iF) Pulse Voltage Rise Time 3 tr — 40 80 ns (VB = 20Vdc, Cc = 0.2nF) "Indicates JEDEC Registered Data (1) Pulse Test: Pulse Width < 300 usec, Duty Cycle < 2%..