INSTALLATION GUIDE Thank you for purchasing an OWNER'S GUIDE American made product by Bulldog Security. To order additional transmitters or other accessories, visit our website at www.directwholesale.net or call Keyless Entry 1-800-659-0764 and Alarm System Model 1402 FOR TECHNICAL ASSISTANCE, CALL 1-800-878-8007 www.bulldogsecurity.com email: [email protected] Wiring diagrams for your vehicle can be accessed by visiting www.bulldogsecurity.com BULLDOG SECURITY Creating A Higher Standard CONTENTS SYSTEM FEATURES System Features ...............................................4-5 2 Four-Button Control your car from an extended Extended Range distance. Remote Control System Components .............................................6 Keyless Entry Remotely locks and unlocks your power Required Tools.....................................................6 door locks. Remote Locking Remotely locks your power door locks Technical Assistance .............................................6 and Unlocking when the ignition is turned on and unlocks with Ignition your power door locks when the ignition Switch is turned off. NOTE: This feature can also Before You Begin...............................................6-7 be used while the unit is wired as an alarm. Precautions ......................................................7-8 Remote Valet Lets you program off the alarm section when it is not needed. Testing Your Wires ...............................................8 Remote Full Time This system will perform all its functions Silent Arming except no chirping when arming or Making Connections .........................................8-10 disarming the system. Remotely Automatically arms the system one Locating & Making Connections .........................10-18 Programmable minute after the last door is closed. Passive Arming Connecting Wiring Harness ...................................18 Last Door When the last door is closed, a series of Indicator beeps or chirps (long, short, long) will Testing Door Locks .........................................18-19 Programmable be heard when the unit is programmed for passive arming. Connecting Door Locks ....................................20-21 Automatic If the same zone is violated three times Annoyance while the system is armed, that Override Using Your Remote Transmitter.........................22-26 zone will be deactivated until the unit is disarmed and rearmed. 3 4 SYSTEM FEATURES CONT. SYSTEM COMPONENTS On-Board Built-in relay provides a positive (+) Your system includes: 1-5-Pin Harness Parking parking light output. No relay needed. 1-Installation & Operation Guide 1-Momentary Switch Light Relay 1-Main Control Module 1-LED Status Indicator 2-Four Button Remote Transmitters and Bracket On-Board Door Built-in relay for Type A, Type B and 1-11-Pin Harness 1-Warranty Lock Relay Type C door locks. REQUIRED TOOLS Plug In Six A visual theft deterrent that flashes when Function LED the system is armed. Lets you know You will need a computer-friendly test light and a 5/16 drill bit Status Indicator which zone has been violated, and when mounting the hood pin switch. In most cases no additional and provides a visual reference for you. tools are required, however if the bottom of your dash on the drivers side will come off you must remove it. In this case a E Square The system will memorize its programmed screwdriver or socket set may be needed. Memory Backup features in the event that the power is lost. TECHNICAL ASSISTANCE Code Learning Allows your keyless/alarm to learn new Should you need help. First check our website at remotes, should you want to add remotes, www.bulldogsecurity.com or call our toll-free Tech Support or if remotes are lost. Hotline Monday through Friday 9AM-8PM and Saturday 10AM- 4PM EST at 800-878-8007. Starter Prevents a thief from starting your vehicle Immobilizer when your system is armed. (Optional You must give the following information: part #775 required) Name Telephone Number with Area Code (Fax number if applicable) Dome Light Illuminates the vehicles interior lights Supervision when the remote transmitter unlock/ disarm button is pressed. (Optional BEFORE YOU BEGIN part #775 required) Congratulations, you have purchased one of the most advanced Two Accessory Use for trunk release, power window alarm systems ever made. Your new system is a technological breakthrough utilizing the most advanced, state of the art Outputs roll up, etc. (Optional part #775 required for all options) Limited Lifetime Guarantees life-long protection. Warranty 5 6 BEFORE YOU BEGIN CONT. PRECAUTIONS CONT. technology and components. It is computer controlled and DO NOT plug the harnesses into the control module until all manufactured in the U.S.A. The dependability and variety of connections have been made. Be careful to line up the pins on features make Bulldog Security the leader in the industry. Enjoy the unit with the wiring harness plug (lip up - Red wire to the your new system for years to come! right). Failure to do this will cause severe damage to the unit and possibly to the vehicle. Since there are many different makes and models of vehicles, look at the wiring chart on our website, TESTING YOUR WIRES www.bulldogsecurity.com/wires.htm. Read this manual thoroughly before starting the installation. When testing for a positive or negative voltage, you must use a computer friendly test light (logic probe) or a volt/ohm meter. Make PRECAUTIONS sure to probe and test each wire before making your connections. This system will add remote keyless entry features to any vehicle MAKING CONNECTIONS with power door locks. This will also work as a replacement system for the factory installed keyless entry system. NOTE:If it is necessary to cut a factory wire to make a connection, see diagram on page 8. Use masking tape to indicate the preferred mounting locations of interior components, LED and override switch. 1. Strip back two inches of insulation on the wire from the remote starter. Two Inches of Bare Wire Disconnect the dome light fuse until you are ready to plug the unit in. 2. Strip back one inch of insulation on the wire you need to connect to. DO NOT use mechanical wiring connections, such as crimp or One Inch of Bare Wire snap together taps. Follow instructions on pages 2-3. DO NOT disconnect the battery if the vehicle has an anti-theft- 3. Separate the vehicle wire as shown. Make the separation large coded radio or is equipped with an airbag. Doing so may cause enough to fit the other wire through. a warning light to be displayed and may require a trip to the dealer to be corrected. 4. Insert the wire(s) from the starter through the hole as shown. if two DO NOT leave the interior or exterior lights on for an extended or more wires are inserted, wrap them in opposite directions. period of time as it may cause battery drain. DO NOT mount the control module until all connections have been made and tested. Using wire ties or double sided tape, MOUNT THE MODULE UNDER THE DASH. 7 8 MAKING CONNECTIONS CONT. MAKING CONNECTIONS CONT. 5. Wrap the wire around one side then the other and finally around 3. Lay upper twisted pair of wires itself as shown. 2 1 over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 3 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them together. Use this method for all connections. 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. Electrical Tape Electrical Tape Wire Tie CAUTION: All wires must be wrapped with tape and wire Wire Ties tied. Use this method ONLY when connecting two separate wires end to end. LOCATING & MAKING MAKING END TO END CONNECTIONS FOLLOW THESE INSTRUCTIONS CONNECTIONS 1. When tying two separate wires together at their ends, strip back 1 CONSTANT POWER (+12V, key in any position including off) of insulation on both wires and separate the strands of wire as shown This system operates on constant 12 volts, the system also needs a source below. of power that is only on when the ignition is turned on (usually referred to as Ignition Power. 1. Locate the wires going to your vehicles ignition switch (usually located 2. Twist upper wires together, twist lower wires together as shown. coming down the steering column). When looking for constant 12 volts: Usually a large gauge wire located at the ignition switch harness. Probe these wires until you find one that turns a computer-friendly test light, or shows 12 volts when the ignition switch is turned to the ON, OFF, START and ACCESSORY positions. If this wire cannot be located at the ignition switch harness, run at least a 16 gauge wire from the positive battery terminal fused at 6 inches from the positive battery post to the inside of the vehicle through the firewall. (Additional hardware is needed.) 2. Mark this with its function Constant Power. 9 10 LOCATING & MAKING LOCATING & MAKING CONNECTIONS CONT. CONNECTIONS CONT. 3. Turn the ignition ON. Probe for a wire that shows 12 volts only when the CONNECTING THE NEGATIVE Optional Part #775 ignition is on. Confirm this by turning the ignition on and off while probing OUTPUT #1, BUTTON #2 TO FACTORY TRUNK each wire. THE BLUE wire is used to operate a WIRE OR OTHER remote car starter, window roll-up POSITIVE 4. Mark this wire with its function Ignition Power. ACTIVATED module, etc. for as long as ACCESSORY 5. If these wires cannot be located, please call our technical support staff at transmitter Button #2 is depressed. BLUE 87a 800-878-8007. NOTE: A SPST or SPDT relay must be used if you want to convert CONNECTING THE POWER AND GROUND the negative signal to positive 1.