29LTDC_CLASSC_MANL_ENG.qx_29LTDDEJR_manual.qx 11/5/13 3:17 PM Page 1 How to Use Your Contents Cobra 29 LTD Classic Features ..................................................................................................1 The CB Story .........................................................................................A1 FCC Regulations FCC Warnings Included Accessories Controls & Indicators ........................................................................A2 Our Thanks to You ..............................................................................A3 Customer Support Installation Location .............................................................................................2 Mounting and Connection .........................................................2 Features of This Product Antennas • 40 CB Radio Channels CB Antenna.......................................................................................6 Marine Installation.........................................................................7 • Heavy-Duty Dynamic Ignition Noise Interference ............................................................7 Microphone Operating Your 29 LTD Classic Turning On Your CB........................................................................8 • Full 4 Watts AM RF Power Output Setting Channel Selector.............................................................9 Calibrate For SWR (Standing Wave Ratio)..............................10 • SWR Calibration Meter To Receive..........................................................................................13 Selecting a Channel.......................................................................14 • Instant Channel 9 S-Meter ...............................................................................................14 NB-ANL/ANL/Off (Noise Blanker/Automatic.........................15 • 4-Pin Front Mount Microphone Noise Limiter Switch) Connector Bright/Dim Switch..........................................................................16 RF Gain Control................................................................................17 • Delta -Tune Setting Delta-Tune .........................................................................18 Setting Squelch ...............................................................................18 • Switchable Automatic Noise To Transmit........................................................................................20 Limiter & Noise Blanker Setting Dynamike®.........................................................................20 Transmit..............................................................................................21 • Adjustable Dynamike® Boost RF Meter.............................................................................................22 External Speaker .............................................................................23 • 9 Ft. Mic Cord PA (Public Address) ........................................................................24 • RF Gain Home And Office Set-Up .............................................................26 Temporary Mobile Set-Up ...........................................................27 How Your CB Can Serve You...........................................................28 A Few Rules You Should Know..................................................28 Channel 9 Emergency Messages..............................................28 CB 10 Codes......................................................................................30 Frequency Ranges..............................................................................32 29 LTD Classic Specifications.........................................................33 Warranty Information.......................................................................34 Optional Accessories ..................................................................35-36 Accessory Order Info.........................................................................37 If You Think You Need Service.....................................Back Cover 1 29LTDC_CLASSC_MANL_ENG.qx_29LTDDEJR_manual.qx 11/5/13 3:17 PM Page 2 Installation Installation Location Location Plan location of transceiver and microphone bracket before starting the installation. Select a location that is convenient for operation, yet does not interfere with the driver or passenger. The transceiver is usually mounted to the underside of the dash with the microphone bracket beside it. Mounting and Mounting and Connection Connection 1 Hold the radio with the mounting bracket in the exact desired location. If there is no Note interference, remove the bracket and use it as The transceiver is held in a template to mark the location for the the universal mounting bracket mounting screws. by two thumbscrews which 3 Connect the antenna cable plug to the allow for adjustment at a receptacle marked “ANT” on the back of convenient angle. the unit. The bracket includes two self-tapping screws and star washers. The mounting must be mechanically strong, conveniently located. 2 Drill the holes and secure the bracket. continued 2 3 29LTDC_CLASSC_MANL_ENG.qx_29LTDDEJR_manual.qx 11/5/13 3:17 PM Page 4 Installation Installation Note Connecting to an accessory fuse prevents the unit from being left on accidentally, and also 6 Plug power cable into back of unit marked permits operating the unit “Power”. Be sure to observe polarity markings. without running the engine. 7 Mount the microphone Note bracket on either side of In positive ground vehicles the the unit (driver’s left) red wire goes to the chassis and using two screws the black wire is connected to supplied. Bracket should the ignition switch. be placed under the dash so microphone is readily Note 4 In a negative grounded vehicle, connect the accessible. Before installing the CB radio, red lead of the DC power cord to an accessory visually check the vehicle’s 12 volt fuse. battery connection to determine which terminal, 5 Connect the black lead to the negative side of positive or negative, is the vehicle. This is usually the chassis. Any grounded (positive is the larger convenient location with a good electrical of the two) to the engine block contact (remove paint) may be used. (or chassis). A negatively grounded vehicle has its negative lead grounded to the 8 Attach the 4-pin microphone cable to chassis. receptacle, on the front of unit and install unit on bracket securely. 4 5 29LTDC_CLASSC_MANL_ENG.qx_29LTDDEJR_manual.qx 11/5/13 3:17 PM Page 6 Marine Installation Antennas Ignition Noise Interference CB Antenna Marine Installation Since the maximum allowable power output of the The transceiver will not operate at maximum transmitter is limited by the FCC and IC, the antenna is CB Antenna efficiency in a boat without a ground plate, (unless critical in affecting transmission distance. Only a it has a steel hull). Before attempting installation , properly matched antenna system will allow maximum consult your dealer for information regarding an power output*. Cobra loaded type antenna models are adequate grounding system and prevention of highly recommended for most installations. Consult electrolysis between fittings in the hull and water. Note your Cobra dealer for further details. For optimum performance in Iginition Noise Interference passenger cars the ideal The transceiver will not operate at maximuUse of antenna location is on the a mobile receiver at low signal levels is normally center of the roof. Second limited by the presence of electrical noise. The choice is on the primary source of noise in automobiles is from center of the trunk. 1 A standard antenna connector is provided the alternator and ignition system. Typically, on the transceiver for easy connection. when signal level is adequate, the background Note *Under Industry Canada regulations, this radio noise does not present a serious problem. Also, Because many newer trucks when extremely low level signals are being feature fiberglass door skins, transmiter may only operate using an antenna of a type and maximum (or lesser) gain approved for the received, the transceiver may be operated with the outside mirror must be the vehicle’s engine turned off. The unit requires grounded to the chassis via a transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type very little current and therefore will not ground strap when antenna is significantly discharge the vehicle’s battery. mounted on the mirror bracket. and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Even though the Cobra 29 LTD Classic has an Note automatic noise limiter, in some installations 3-way Combination Safety notice: The device complies with the MPE ignition interference may be high enough to Antennas are also available requirements by providing a safe separation distance make good communications impossible. Many which allow operation of all of 14.2 in (36 cm) between the antenna, including any possibilities exist and variations between vehicles three bands (AM-FM & CB), radiating structure, and any persons when normally require different solutions. Consult your COBRA using a single antenna. operated . This is based on a typical installation and dealer or a 2-way radio technician for help in However, this type of antenna an antenna with 3 dBi of gain. This device is approved locating the source of a severe noise. usually results in less than