Mini-ITX MX700CX/ CXD VIA CX700/ C7 VIA ALL-IN-ONE SYSTEM PROCESSOR ITX Board With LVDS FP, HD Audio,6 USB 2.0, 2 Gigabit Ethernet User’s Manual http://www.bcmcom.com Disclaimer The information in this document is subject to change without notice. The manufacturer makes no representations or warranties regarding the contents of this manual and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, the manufacturer reserves the right to revise this publication or make changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or change. Trademarks Microsoft and Windows are registered trademarks of Microsoft Corp. Intel and Pentium is registered trademarks of Intel Corporation. Other product names used in this manual are the properties of their respective owners and are acknowledged. Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. BCM ©Copyright 2008 FCC Compliance Statement This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna 2. Move the equipment away from the receiver 3. Plug the equipment into an outlet on a circuit different from that to which the receiver is connected 4. Consult the dealer or an experienced radio/television technician for additional suggestions You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void your authority to operate such equipment. This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. Safety Precautions Warning! Always completely disconnect the power cord from your chassis or power cable from your board whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static- shielded bag when they are not in the chassis. WARNING: CMOS BATTERY DAMAGE Replace your system’s CMOS RAM battery only with the identical CR-2032 3V Lithium- Ion coin cell (or equivalent) battery type to avoid risk of personal injury or physical damage to your equipment. Always dispose of used batteries according to the manufacturer’s instructions, or as required by the local ordinance (where applicable). The damage due to not following this warning will void. TABLE OF CONTENT USER’S NOTICE DISCLAIMER COMPLIANCE STATEMENT SAFETY PRECAUTIONS TABLE OF CONTENT 1 MANUAL REVISION INFORMATION & ITEM CHECK LIST 2 CHAPTER 1 INTRODUCTION OF MX700CX/CXD MOTHERBOARD FEATURE OF MOTHERBOARD 3 SPECIFICATION 5 SYSTEM DIAGRAM 6 JUMPER & CONNECTOR SETTING 7 CHAPTER 2 HARDWARE INSTALLATION HARDWARE INSTALLATION STEPS 9 CHECKING MOTHERBOARD'S JUMPER SETTING 9 GLOSSARY 10 ABOUT VIA C7 CPU 11 INSTALL MEMORY 12 EXPANSION CARD 13 PROCEDURE FOR EXPANSION CARD INSTALLATION 13 ASSIGNING IRQ FOR EXPANSION CARD 13 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD 14 CONNECTORS, HEADERS 14 CONNECTORS 14 HEADERS 16 STARTING UP YOUR COMPUTER 20 CHAPTER 3 INTRODUCING BIOS ENTERING SETUP 22 GETTING HELP 22 THE MAIN MENU 23 MAIN 25 ADVANCED BIOS FEATURES 28 ADVANCED CHIPSET FEATURES 30 AGP & P2P BRIDGE CONTROL 31 DRAM TIMING SETTINGS 32 INTEGRATED PERIPHERALS 33 VIA ONCHIP IDE DEVICE 34 VIA ONCHIP PCI DEVICE 36 ONBOARD SERIAL PORT 1/ 2/ 3/ 4 37 USB DEVICE SETTING 39 POWER MANAGEMENT SETUP 40 WAKEUP EVENT DETECT 42 PC HEALTH STATUS 43 PC HEALTH 48 EXIT 49 MX700CX/ CXD Motherboard I/O Mechanical Draw 50 1 Manual Revision Information Reversion Revision History Date 1.0 First Release JUNE 2008 Item Checklist 5 1x MX700CX 5 1x 80 wire ATA66/100 IDE cable 5 1x Driver/ Manual utilities CD 5 1x Standard I/O Shield 5 1x MX700CX Quick Reference Guide 5 2x SATA Cables 2 VIA CX700 Series ALL-IN-ONE SYSTEM PROCESSOR z 800/ 400 MHz FSB VIA C7 Processor z DDR2 533/ 400 SDRAM Controller z Integrated UniChrome Pro II 3D/ 2D Graphics & Video Processor z Integrated HDTV Encoder and LVDS/ DVI Transmitter z High Definition Audio Controller z Two Serial ATA Ports z One UltraDMA-133 EIDE Channel z USB 2.0/ 1.1 Ports z PCI 32-bit 33MHz Bus z 2 RS-232 Serial Ports z RTC and LPC z ACPI and Power Management 3 Chapter 1 Introduction Feature of motherboard The MX700CX/ MX700CXD combines the high performance and exceptional value of VIA CX700 chipset with a full-featured, Embedded board. The VIA All-in-One chipset support 800/ 400MHz FSB C7 Processor, that memory base on the FSB 533/ 400 MHz operation supports DDRII SDRAM . In the meantime, the CX700M chipset integrated the LVDS & VGA function. The MX700CX/ MX700CXD system memory size can be up to 1GB DDRII memory, onboard dual Gigabit Ethernet controllers (support 10/100/1000 Base-TX Ethernet), HD Audio Line-Out and 4 COM ports, besides the MX700CX/ MX700CXD with four USB2.0 ports on rear panel plus two internal USB2.0 ports. The MX700CX/ MX700CXD mini ITX Board is a valuable and it is suitable for all the embedded applications, which also well support with the Windows® 98/ 2000/ XP and Linux operating system. MX700CX/ MX700CXD does provide scalability with high performance & Longevity for Embedded Application. It is really a wise choice of computing solution. 4 Specification Spec Description Design ∗ Mini ITX form factor 6.69”(W) x 6.69”(D) (170 x 170 mm) Chipset ∗ Single chip solution: VIA CX700M CPU ∗ 1.5GHz BGA (Optional 1GHz/ 2GHz). ∗ System bus Frequency 400/533MHz FSB Video Display ∗ UniChrome Pro II 2D/ 3D Graphics Memory Socket ∗ 240-pin DDRII SDRAM module socket 1x ∗ Support Memory Type 64/ 128/ 256/ 512Mbit (x8/ x16/ x32) Technology ∗ Support 1Gb (x16) ∗ Support DDR2 533/ 400 SDRAM ∗ Non ECC error correction in the frame buffer space Expansion Slot ∗ 1x 32-bit PCI slot ∗ PCI Rev 2.3 compliant Storage ∗ Single Channel IDE controllers support PCI Bus Mastering, ATA PIO/DMA and the ULTRA DMA 133 functions that deliver the data transfer rate up to 133 MB/s ∗ 2 SATA Support 150Gbit/s, 300Gbit/s complies with SATA specification 1.0 and SATA II . ∗ 1 CF Type II slot (Share with IDE Channel) LAN On Board ∗ Dual Gigabit 10/100/1000 PCI Ethernet LAN Audio ∗ AC’97 Digital Audio controller integrated ∗ 7.1 HD Audio CODEC on board ∗ Sound Blaster Pro compliant BIOS ∗ Phoenix/ Award 4MB Flash ROM I/O ∗ PS/2 keyboard and PS/2 mouse connectors ∗ Parallel port x1, Serial port x4 (two on header) ∗ USB 2.0 connector x6, (2 on header) ∗ Audio connector Line-out ∗ Fast IRDA pin header BIOS ∗ Award (Phoenix PNP BIOS) ∗ APM /ACPI compliant Power ∗ ATX standard 20-pin power connector (MX700CX) ∗ 12V DC 4 Pin Power & 1x 4 pin 5V/ 12V Disk Power (MX700CXD only) 5 System Diagram MX700CX/ MX700CXD Mainboard Diagram 6 Jumper & Connector 7 Jumper / Connector Name Description Note J1 I2C Bus Connector 1x 4 pin J2, J3, J4, COM1, COM2, COM3, COM4 Power 4x 3 pin J5 Jumper J7 LCD Power Source 1x 3 pin J8 Front Panel LAN LED 2 x 5 pin CLR_CMOS Clear CMOS Jumper 1x 3 pin JCF_SEL1 Compact Flash Select 1x 3 pin IDEB1 IDE 2x 20 pin (keyed) CF1 Compact Flash Slot SATA1 Serial ATA 1 SATA2 Serial ATA 2 JAUD1 Audio Amplifier 1x 4 pin JAUD2 Front Audio 2x7 pin (keyed) CPUFAN1 CPU fan 1x 3 pin SYSFAN1 System fan 1x 3 pin TV/CRT TV Out / CRT Out Select 1x 3pin JTV1 TV Out 2x3 pin (keyed) JFP1 Front Panel 2x5 pin (keyed) JLPT1 Parallel Port 2x13 pin (keyed) F_USB1 Front USB1 2x5 pin (keyed) PCI1 PCI Slot MINIPCI1 MINI PCI Slot JLVDS1 LVDS Connector 2x20 pin IRDA1 IRDA Header 2x 3 (keyed) JCD1 CD_IN Header 1x 4 pin CON1 Mini PCI-Express Slot ATX1 ATX Power Connector 2x 10 Block 8 Chapter 2 Hardware installation Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. Connect ATX Power cable 7. Power-On and Load Standard Default 8. Reboot 9. Install Operating System 10. Install Driver and Utility Checking Motherboard’s Jumper Setting (1) CMOS RAM clear (3-pin): CLR_CMOS A battery must be used to retain the motherboard configuration in CMOS RAM, short 2-3 pins of CLR_CMOS to store the CMOS data.
Details
-
File Typepdf
-
Upload Time-
-
Content LanguagesEnglish
-
Upload UserAnonymous/Not logged-in
-
File Pages59 Page
-
File Size-