Verification of the Laws of Vibration of Stretched Strings

Verification of the Laws of Vibration of Stretched Strings

Lab Experiments 136 KamalJeeth Instrumentation and Service Unit Experiment-367 F VERIFICATION OF THE LAWS OF VIBRATION OF STRETCHED STRINGS Jeethendra Kumar P K, Ajeya PadmaJeeth and Santhosh K KamalJeeth Instrumentation & Service Unit, No-610, Tata Nagar, Bengaluru-560092. INDIA. Email: [email protected] Abstract Using a new type of metal sonometer, speaker vibrator and power oscillator, the three laws concerning vibration of stretched strings are verified. This sonometer is easier to handle compared the available sonometers and moreover the vibrations produced are of high amplitude which are normally not observed in case of other sonometers conventionally used in physics laboratories. Introduction Marin Mersenne, a French scientist first published correct theoretical equations and formulated laws of vibration of stretched strings in 1636. He studied the vibrations of musical tones by using brass-ball weights attached to brass wires, adjusting the tension with appropriate weight attached to the wires [1]. Mersenne observed that the frequency of oscillation is inversely proportional to vibrating length of the string, directly proportional to the square root of tension and inversely proportional to the square root of mass of the string. Based on these observations, he formulated an equation describing vibration of stretched string as ͥ …1 $ = ǯ( where , ϑ is frequency of vibration T is the tension (force) on the string, m is the unit mass of the string, and L is the vibrating length of the string. The tension T is applied by tying a weight (W) at the free end of the string. T = Wg …2 where W is weight tied to the string, and g is acceleration due to gravity. Vol-12, No-2, June-2012 Lab Experiments 137 KamalJeeth Instrumentation and Service Unit Based on Equation-1, Mersenne formulated three laws of stretched string vibration as a) Law of velocity, b) Law of tension, and c) Law of mass These three laws were formulated as a result of his earlier observations on vibration of stretched strings. When the tension and mass per unit length are constant, the frequency is proportional to 1/L. α ͥ , or ϑ ϑL is constant. ΀ This is known as the law of Velocity. The constant appearing in this equation is the velocity of the sound through the wire which remains constant under this condition. Therefore, a graph of 1/L versus is a straight line, with slope given by $ Slope = V = λ velocity ϑ where V is the velocity, and λ is the wavelength. From Equation-1 Έ gives the velocity, V, as ϑL = ǯΛ V= Έ and …3 ǯΛ L = λ …4 Keeping ‘m’ and ′ ′, constant, Equation-1 can be rewritten as ϑ √Έ ͥ or ϑ = Λ ΀ √ Ϝ ͥ ͥ ...5 = √Έ √Λ ΀ Equation-5 represents a straight line, with slope given by Slope mass = ͥ …6 √( This is the law of Mass Keeping and T constant, one obtains the law of tension for a stretched string as $ = ͥ …7 ϑ√m √T ΀ Vol-12, No-2, June-2012 Lab Experiments 138 KamalJeeth Instrumentation and Service Unit Equatuion-7 represents a straight line with slope given by Slope = …8 Tension √T This is the law of Tension. Therefore, one can summarize the three laws concerning vibration of stretched string, as given in Table-1. Table-1 Law of Held constant Proved constant Straight line Slope Velocity m, T υ L = V V 1 versus ϑ ͆ Mass m, υ/ = ͥ ͥ versus υ/ ϑ 1 √T √Λ ΀ √T √m Tension , T υ = ͥ ϑ m T versus √ √ ΀ $√m √T The three laws of vibration of stretched strings Stretched string vibrators A thread or a wire stretched fully with a weight hanging on its end is called a stretched string. Such a string can be made to vibrate with external excitation. One can make the string vibrate with different types of vibrators. A tuning fork is the simplest type of exciter. The sound produced by the tuning fork travels through the string with the velocity which is governed by (i) the weight of the string, (ii) tension in the string, and (iii) frequency of the exciter . An AC current when passed through a copper wire held as a stretched string and pair of magnets placed on both the sides produce vibration in the string. An electromagnet placed above the stretched string can also produce vibration. If the wavelength of the exciter frequency matches with the length of the wire, vibrations can be seen as wave motion on the string. Based on this principle, some of the vibrators generally used in Physics labs are: Melde’s tuning fork, electrical vibrator, and a set of tuning forks. In this experiment, a speaker vibrator is introduced which is much superior to the available vibrators because it can produce oscillations with large amplitude. The new metal Sonometer Sonometer [2] is an instrument generally used to verify the three laws of Mersenne, in which the sound box is designed using a wooden board. Sonometers made of teak wood are excellent but are not available now due to their high cost. Due to poor quality of wood used for making sonometers, they usually get damaged during transit and/or storage. Further, their long size (1m) adds to the possibility of their damage. Hence we have replaced wood with metal box of small size; the maximum size being 60cm. Smaller length together with lower weights and thin wire make them more suitable for frequencies between 30-130 Hz. In general, in the sonometer experiments a tuning fork or an electromagnet is used as the exciter. In this experiment we have used a tweeter (speaker) as the exciter. Vol-12, No-2, June-2012 Lab Experiments 139 KamalJeeth Instrumentation and Service Unit Tweeter vibrator Figure-1: Tweeter vibrator A three inch (7.5 cm) tweeter is selected for this application with 16 Ω dc resistance. The cap of the voice coil is reshaped. A light weight, 15mm long aluminum tube with 10mm dia is glued to the voice coil cap. A rubber rod is fixed on the aluminum tube. An aluminum strip, 10mm wide 1mm thick and 10cm long is fixed such that it remains in contact with the rubber rod, as shown in Figure-1. This picks up the vibrations from the voice coil and starts vibrating. A cotton thread or metal wire is tied to the aluminum plate which passes over a pulley and two bridges that are used to adjust the vibrating length of the string. Figure-2: The new sonometer with vibrator The entire unit is fitted to one end of the sonometer as shown in Figure-2. A power oscillator with variable frequency is provided along with the instrument which can be connected to the speaker. The power oscillator generates sinusoidal waveform; with frequency varying from 50Hz to 130Hz. Figure-3 shows the power oscillator. Figure-3: Variable frequency power oscillator Vol-12, No-2, June-2012 Lab Experiments 140 KamalJeeth Instrumentation and Service Unit B Amplitude Input sine wave B E C A Equilibrium position 0 T/4 T/2 3T/4 T Time A C E Voice coil movement D D Figure-4: Vibrations of the voice coil (left) and the input sine wave (right) A sine wave of period T drives the speaker; the voice coil of the tweeter moves up and down as shown in Figure-4. When T=0, the voice coil is at its equilibrium position A. When the time is T/4, the voice coil moves to the upper position B; when time is T/2, the voice coil comes to the equilibrium position; when time is 3T/4 the voice coil is at the position D; and when the time is T the voice coil comes back to its equilibrium position. Hence during the period T, the voice coil completes one oscillation and, therefore, the period of the voice coil is the same as that of the sine wave. B A,C,E Loop on string Metal strip D Speaker Figure-5: Vibration of the string A string or thread tied to the vibrator will oscillate, as shown in Figure-5. There will be a loop with the maximum amplitude when the wavelengths of the vibrating string match with the input frequency in which case the vibrating length of the string is given by L= λ …9 where L is length of the loop vibrating with the maximum amplitude, and λ is the wavelength of the input signal driving the speaker Vol-12, No-2, June-2012 Lab Experiments 141 KamalJeeth Instrumentation and Service Unit Hence if we determine the length of loop with the maximum amplitude, the velocity of the sound travelling on the string can be determined and the three laws of vibration of stretched strings can be verified experimentally [2]. Apparatus used Sonometer fitted with tweeter vibrator, power oscillator 50-130Hz variable frequency, slotted weights 5 numbers each of 20gm, and wires of iron (0.3mm dia), cotton thread, twin thread, nylon thread, and digital scale to weigh up to 300gm. The complete experimental set-up is shown in Figure-2. Experimental procedure The experiment consists of three parts, namely Part-A: Law of Velocity Part-B: Law of Tension Part-C: Law of Mass Part-A: Law of Velocity In this part of the experiment, m and T are held constant throughout the experiment, frequency of vibration is varied and the corresponding vibration length is determined. 1. The twin thread (green color) is selected for this part of the experiment. Thread of exactly one meter length is taken and its mass (M) is determined using the digital balance.

View Full Text

Details

  • File Type
    pdf
  • Upload Time
    -
  • Content Languages
    English
  • Upload User
    Anonymous/Not logged-in
  • File Pages
    10 Page
  • File Size
    -

Download

Channel Download Status
Express Download Enable

Copyright

We respect the copyrights and intellectual property rights of all users. All uploaded documents are either original works of the uploader or authorized works of the rightful owners.

  • Not to be reproduced or distributed without explicit permission.
  • Not used for commercial purposes outside of approved use cases.
  • Not used to infringe on the rights of the original creators.
  • If you believe any content infringes your copyright, please contact us immediately.

Support

For help with questions, suggestions, or problems, please contact us