Data Sheet 1-491 Rev. April 2016 Fire prevention and control on construction sites Fire at a construction site can endanger the lives be closely followed throughout the course of workers and others who happen to be on the of construction. The fi re protection plan is site. A fi re during the course of construction also a vital segment of the overall project safety can result in severe structural damage; destruction program. Required detail will depend on of machinery, equipment or materials; and the size and complexity of the construction untimely delay in project completion. operations involved. This data sheet lists the 1. The fi re-loss potential during the construction elements that should be covered in the plan. phase is far greater than after project completion. During construction, hazards Assignment of responsibility inherently associated with building operations and authority are continually being generated. At the same 3. Project management—whether owner, time, permanent fi re protection systems and construction manager, prime contractor or equipment are usually not yet in place or, a combination thereof—must clearly assign at best, only partially in service. Likewise, and spell out the responsibility for site fi re vertical and horizontal fi re-related structures protection before the start of the project. (i.e. walls, fl oors, doors, etc.), designed All contractors and subcontractors should to minimize fi re spread, are usually not be made aware of this responsibility and completed until late in the construction authority assignment. Procedures should schedule. be established for expedient handling of “imminent danger”-type hazards. Fire protection plan 2. It is essential, therefore, that an effective Coordination with outside agencies fi re prevention and extinguishing plan be 4. Determine applicable requirements concerning developed before the onset of construction. such items as temporary power and lighting, The plan should be put into practice as soon blasting, storage of fl ammables and temporary as construction operations begin and should heating devices, and the like. 1 0416 900009145 ©2016 National Safety Council 5. The local fire department should be made aware 9. Each investigation should yield information for of construction plans and should be kept up to corrective measures designed to minimize the date during the course of construction regarding possibility of recurrence and, where needed, to items such as access to the site during both improve fire suppression. working and non-working hours; and the location of standpipe systems, pumper connections, fuel Training in emergency procedures storage, stairways, elevators, hoists, power and 10. Worker response in a fire-emergency situation fuel shutoffs, emergency generators, and fixed-fire is directly related to training. All workers on site extinguishing systems. The fire department also should be aware of the procedure for reporting may provide a source for training in the proper a fire and evacuating the worksite. These use of first aid, fire extinguishers and standpipe procedures should be posted in prominent hose systems. Inviting the local fire department areas. All workers should be trained concerning to inspect the worksite can be beneficial for both these procedures. parties. Fire departments should be made aware of 11. Emergency telephone numbers should be chemicals or hazardous substances on site. available to all workers. 6. Other agencies, such as local police authorities and 12. An alarm system should be provided to alert utility companies, should be consulted concerning all workers of a fire emergency. Designate a such items as site security; location of underground location where all workers will assemble following utilities; and emergency shutoff of electricity, evacuation and confirm that all personnel have gas and water. A liaison may be necessary with been safely evacuated. agencies such as the National Weather Service when the site is subject to tornadoes, hurricanes, 13. Selected workers on each work shift should floods or other natural hazards. Procedures should be trained in the proper use of portable fire be established for early warning, orderly shutdown extinguishers. Training should address the four of construction operations, and protection of classifications of fire, the type of extinguishers workers and property. List an appropriate “One suitable for each class and the proper technique Call” number. to be used in operating each type. Extinguisher suppliers or the local fire department may be Fire prevention inspections willing to provide, or assist in, this training. 7. Periodic site inspections should be conducted Notify fire department first. Then utilize fire by the person responsible for fire prevention and extinguishers by trained personnel for the initial control, or someone who has been delegated small stage of fire. to this duty. It is essential that the individual Types of fires making the inspection be competent in hazard identification as well as the corrective measures 14. Class A fires occur in wood, rubber, paper, required for elimination or control of all hazards cloth and most plastics. The most effective type noted. The fire prevention inspection report should of extinguishing agent is one using water, or be written and received by project management. solutions containing large concentrations of water, Include an inspection form. because the ‘‘quenching-cooling’’ effect reduces the temperature of the burning material below its Fire investigation ignition temperature. Fire extinguishers suitable for 8. Regardless of its size or resultant damage, this type of fire are designated with a classification every fire should be investigated to determine of “A” on the label. its cause and to evaluate the effectiveness of its 15. Class B fires occur in flammable or combustible extinguishment. liquids, such as petroleum products and greases. 2 A “blanketingsmothering” effect of an agent that Woodworking excludes oxygen or inhibits the chemical chain 20. When appropriate, the woodworking area should reaction is most effective. Extinguishers labeled be set up in a remote area of the project. Where “Class B” employ carbon dioxide, dry chemical, possible, dust-collecting apparatus should be Halon or foam. installed for power equipment. Dust, scraps and 16. Class C fires involve electrical equipment. The refuse should be removed regularly and properly extinguishing agent must be non-conductive. disposed of. Smoking should be prohibited in the Carbon dioxide, dry chemical and Halon are area. the normal types used for electrical fires. 17. Class D fires involve combustible metals such as Automatic sprinklers aluminum, magnesium, zirconium and titanium. 21. Expedite the installation of automatic sprinklers. The use of water and some other conventional Underground mains, hydrants and a source of types of extinguishing agents are ineffective and water should be provided in the earliest stages of may cause a violent reaction. These fires can construction. The goal should be to get sprinklers be extinguished with specially prepared agents. in service ahead of combustible occupancy and Where this hazard exists, extinguishing agents immediately following combustible construction. with a D-class rating should be provided. In multi-story buildings, capped standpipes All on-site fire extinguishers should be with hose connections should be extended serviced and inspected. upward as the various floors are constructed. There should be a conspicuously marked fire Cutting and welding department pumper connection on the outside 18. Cutting and welding sparks cause more of the building at street level. The local fire construction fires than any other ignition source. department should be aware of the existence The person responsible for fire safety should of the connection as soon as it is in service. implement fire protection systems and ensure adequate precautions are taken. Special Security service and fire alarms safeguards may be needed for combustible 22. Provide watch service at night and during materials, such as relocating the combustibles non-working days as soon as construction or covering them with flameproof tarpaulins. At is started for construction projects. Make some locations, it may be unsafe to use a torch sure the security service is familiar with regardless of the precautions taken. Store fuel special fire hazards. gas and oxygen cylinders upright and secure in safe locations, protected from high temperatures Temporary heating and adequately separated from each other. 23. Local codes may vary as to the types of heating Obtain hot work permits. Establish a fire watch equipment and fuel storage arrangements before and after cutting. permitted. All heating equipment must be provided with proper clearance from combustible Flammable and combustible liquids materials and with necessary ventilation. Fuels 19. The storage and use of flammable liquids is a must be properly stored and handled. Heating hazard. Fuels, solvents, paints and adhesives equipment must be properly maintained and are among those liquids requiring control and operated by trained personnel. Temporary safeguarding. Controls include proper storage enclosures should be made with flame-resistant and adequate ventilation. materials. 3 Figure 1. Recommended extinguisher marking labels. When an application is prohibited, the background is black and the slash is bright red. Otherwise the background is light blue. Combustible materials 24. A wide range of combustible