LS 4000i Series Product Reference Guide LS 4000i Series Product Reference Guide 70-37898-03 Revision A — October 2000 2 Symbol Technologies, Inc. One Symbol Plaza, Holtsville N.Y. 11742-1300 LS 4000i Series Product Reference Guide 70-37898-03 Revision A October 2000 1999-2000 by Symbol Technologies, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Symbol. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Symbol grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Symbol. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from Symbol. The user agrees to maintain Symbol’s copyright notice on the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof. Symbol reserves the right to make changes to any software or product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any Symbol Technologies, Inc., intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Symbol products. Symbol, Spectrum One, and Spectrum24 are registered trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Symbol Technologies, Inc. One Symbol Plaza Holtsville, New York 11742-1300 http://www.symbol.com ii Contents About This Manual Chapter Descriptions . .ix Notational Conventions . x Related Publications . x Service Information . x Symbol Support Center . xi Warranty . xiii Warranty Coverage and Procedure . xiv General. xiv Chapter 1. LS 4000i Series Scanners Introduction . 1-1 Chapter 2. Set Up Introduction . 2-1 General . 2-1 Unpacking. 2-1 Scanner Cable . 2-1 LS 4004i. 2-3 Power Options . 2-3 Connecting to a Host: 1-D Scanning . 2-4 LS 4005i. 2-6 Power Options . 2-6 Connecting to a Host: 1-D Scanning . 2-6 LS 4006i. 2-8 Power Options . 2-8 Connecting to a Host: 1-D Scanning . 2-9 LS 4007i. 2-9 Power Options . 2-9 iii LS 4000i Series Product Reference Guide Connecting to a Host: 1-D Scanning . 2-9 Connecting to a Host: PDF Scanning . 2-11 Chapter 3. Scanning Scanning 1-D Bar Codes . .3-1 Aiming . .. 3-1 Scanning PDF417 (2-D) Bar Codes . 3-2 Chapter 4. Maintenance & Specifications Maintenance . 4-1 Accessories. .. 4-1 Standard Accessories . 4-1 Optional Accessories . .4-1 Technical Specifications . 4-3 LS 400Xi 1-D Decode Zone . 4-5 LS 400Xi 2-D Decode Zone . 4-6 Pin-outs. .. 4-7 Beeper Indications . 4-8 Troubleshooting . 4-9 Chapter 5. Parameter Menus Operational Parameters . 5-1 Set Default Parameter. .5-6 Host Type . 5-7 IBM 46XX Host Types . .5-7 RS-232C Host Types. .5-8 Keyboard Wedge Host Types . 5-11 Beeper Tone . 5-12 Beeper Volume . 5-13 Laser On Time . 5-14 Power Mode . 5-15 Beep After Good Decode . 5-16 Transmit “No Read” Message . ..