Assembly & Operating THE Instructions For: GOLFWORKS Maltby Putter ® Bending Machine Code: MA2012 CONTENTS: FEATURES: In the box you should • Easily clamps, measures and bends all right and left handed putters. receive the following: • Heavy Duty CNC milled components. 1 Maltby Design Putter • Universal design eliminates the need for special attachments or disassembly regardless of the Bending Machine putter type. Traditional blade designs and modern oversized high MOI putters are equally easy (MA2012) to securely clamp, measure and bend. 1 Adjustable Brass Non- • Smooth sliding protractor quickly and accurately measures the loft and lie angles of all putters. Marring Bending Bar (BNMB) • Firm rubber, auto adjusting, soling pads help level the putter head and protect the sole against 1 Putter Hosel Bending Bar dents and scratching during bending. (GW1058) • Putter Hosel Bending Bar GW1058. 1 Allen Wrench • Can be bench mounted using the MA2013 bench mount stand. 4 Mounting bolts with nuts • Can be floor mounted using the MA2003AD heavy duty floor mount stand. *It is recommended that the The Maltby Putter Bending Machine (MA2012) was designed for the professional clubmaker. This Maltby Putter Bending machine needs no disassembly of parts or special attachments to safely clamp, bend and measure any Machine be mounted on right or left handed putter head. For the proper set up and operation, it is recommended the MA2012 either the Bench Top Stand Maltby Putter Bending Machine be mounted to either the Bench Mount (MA2013) or the Floor Mount (MA2013) or the Floor Stand (MA2003AD). Mount Stand (MA2003AD). SET-UP The MA2012 can also be 1 2 3 mounted to the heavy duty floor stand (MA2003AD) that is designed to be mounted to a solid floor (see photo 3). (Bolts not included for mounting the stand to the floor. Consult your local hardware store for the correct anchor bolts for Edge of your particular floor type). Bench The base of the machine has four countersunk The MA2012 can be bench mounted The base of the machine has four holes that easily line up using the Benchtop mount (photo 1). If countersunk holes that easily line up with with the base holes. Four using the Benchtop mount, position the the base holes. Four flat head bolts with flat head bolts with nuts front the machine to the front of the nuts are included, along with an Allen are included, along with an Allen wrench, for easy work bench to give easy access to the wrench, for easy installation. top clamp knob (see photo 2). installation. Once the Maltby Putter Bending Machine is mounted securely to either the bench top stand or the floor stand, it is ready for use. 4820 Jacksontown Road | P.O. Box 3008 • Newark, Ohio 43058-3008 | Toll Free: 800-848-8358 • FAX: 800-800-3290 | Canada Toll Free: 800-387-5331 SHIPPING e-mail: [email protected] CODE website: www.golfworks.com T OPERATION 4 5 6 7 The MA2012 is designed with There is also a brass knob machine. The square position Re-check the position of the several key features to aid in on the sliding protractor is achieved when the topline of putter, making sure the top installing putters into the assembly that is used to the putter is parallel to the line of the putter face is machine. Photo 4 shows the adjust the protractor to the straight top line of the face parallel to the top line of the two rubber, self adjusting sole needed height to insure the block (see photo 7). To secure face block. The MA2012 pads that helps position the measurements of loft and lie this style of putter in the also has a top clamp with putter square in the machine. are taken on the straight machine, position the putter, two round rubber inserts The face block (photo 5) is portion of the putter shaft visually aligning the top line (see photo 9). designed with a 4˚ angle (see photo 6). with the face block, and facing the putter face. This Any current style of putter can tighten the T-bar so that the angle helps secure the putter be clamped and measured in nylon pad on the back brace head in the machine and the Maltby Putter Bending is up against the back of the prevents slippage when machine. Photo 7 shows a putter (see photo 8). adjusting the lie of a putter. common style of cavity back putter (Ping Anser style) postioned squarely in the MEASURING THE LOFT & LIE 8 9 10 11 The rubber inserts are Once the putter head is square Once the putter is correctly Hold the shaft guide up designed to prevent marring in the machine, with the back positioned in the machine, against the shaft as shown in the top edge of the putter. It brace securely tightened, and position the sliding protractor photo 13. When the shaft may be necessary to snug the the top clamp securely to the right side of the machine guide is in place, the top clamp down onto the top tightened (if necessary), the (for a right handed putter). protractor will register the lie edge of the putter to prevent putter is ready for measuring The protractor assembly is of the putter on the lie scale slippage when adjusting the and bending (see photo 11). designed to give you (see photo 14). In photo 14 loft and lie of the putter. If it is simultaneous readings of both the lie reading of the putter is deemed necessary to use this the loft and lie of a putter. To 71˚. The loft scale is on the clamp, position the rubber position the protractor in place side of the protractor (see inserts over the top of the for reading, slide the protractor photo 15). putter and tighten the top arm forward as seen in photo clamp by turning the black 12. The sliding arm has a knob on the bottom side of slotted shaft guide that rests the machine (see photo 10). up against the shaft for both right and left hand putters. 12 13 14 15 In this instance, the loft There is no disassembly To install a standard size mallet Turn the T-bar bolt until reading of the putter is 2˚. For required to install a left hand putter in the machine, you enough space is available to left handed putters, install the putter in the machine and read must first move the back cavity allow the mallet style putter to putter in the same manner as the loft and lie specifications. brace out of the way to allow be placed in the machine. for a right handed putter. Multiple types of putter the T-bolt to be pulled far Place the mallet style putter in Once the putter is in place, designs, both right and left enough back to accommodate the machine in the same simply slide the protractor to handed, can be registered in the mallet design. To do this, manner as the standard style the left hand side of the the Maltby Putter Bending simply raise the back brace and putter, with the face flush up machine, pull the shaft guide machine. For most mallet turn it to the side (see photo against the face block. While into position and read the lie styles of putters, the back 17). Lay it down so the nylon holding the putter in position and loft readings in the same cavity brace is not necessary to end of the brace is touching with the face flush against the manner as the right hand secure a mallet style putter in the base. As you are facing face block, tighten the T-bar putters (see photo 16). the machine. the machine from the front, bolt by turning counter turn the T-bar bolt clockwise clockwise. to retract the clamp towards the back of the machine. 16 17 18 19 Tighten until the curved back brass knob to raise the shaft For larger style mallet putters, The same procedures used for brace is snug up against the guide arm to a position where the same procedures as used registering the standard and back of the putter (see photo it can be placed flush on the for the small style mallet are mallet styles apply for a center 18). If necessary, position the shaft, above the bend in the used. The T-bar bolt will have shafted putter, with the top line bracket as shown in shaft. Photo 19 shows a to be pulled further back to possible exception of the top photo 18 and tighten snug by double bend shaft style putter accommodate the larger style clamp application. Depending turning the black knob on with the shaft guide properly in mallet. Photo 20 shows a large on the style of the center the under side front of the position to take the lie and loft style mallet properly registered shafted putter and the length machine. Photo 18 shows a readings. in the machine. of the blade, the top clamp popular style two ball putter Center shafted putters can also may need to be positioned with a double bend shaft be registered in the Maltby toward the toe of the putter. correctly registered in the Design Putter Bending Photos 21A and 21B show a machine. It may be necessary machine for measuring and mid size, center shafted mallet to adjust the height of the bending. properly positioned in the protractor arm using brass machine, ready for measuring. height control knob (refer to photo 6). If needed, turn the ADJUSTING (BENDING) THE LOFT & LIE STANDARD STYLE PUTTER 20 21 AB21 22 The Maltby Putter Bending A short, quick application of After pressure is applied to After bending, slide the machine comes with an pressure or a constant pressure bend the lie of the putter protractor assembly into adjustable brass bending bar are the two techniques that are flatter or more upright, position and check the (BNMB).
Details
-
File Typepdf
-
Upload Time-
-
Content LanguagesEnglish
-
Upload UserAnonymous/Not logged-in
-
File Pages6 Page
-
File Size-