Page 1 of 35 EMC Technologies Pty. Ltd. ABN 82 057 105 549 Melbourne Sydney 176 Harrick Road Unit 3/87 Station Road Keilor Park, Vic 3042 Seven Hills, NSW 2147 Tel: +61 3 9365 1000 Tel: +61 2 9624 2777 Email: [email protected] Web: www.emctech.com.au 47 CFR PART 15, SUBPART B TEST REPORT REPORT NUMBER: M2003018-9 TEST STANDARD: 47 CFR PART 15 RADIO FREQUENCY DEVICES SUBPART B – UNINTENTIONAL RADIATORS CLIENT: SMART FOAL PTY LTD DEVICE: SMART FOAL HOME MODELS: BASE STATION: 2.0 REPEATER: 1.2 TRANSMITTER: 1.9 DATE OF ISSUE: 17 JUNE 2020 EMC Technologies Pty Ltd reports apply only to the specific samples tested under stated test conditions. It is the manufacturer’s responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. EMC Technologies Pty Ltd shall have no liability for any deductions, inferences or generalisations drawn by the client or others from EMC Technologies Pty Ltd issued reports. This report shall not be used to claim, constitute or imply product endorsement by EMC Technologies Pty Ltd. Accredited for compliance with ISO/IEC 17025 – Testing. The results of tests, calibration and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, medical testing, calibration and inspection reports. Except for the Certificate of Compliance, this document must only be reproduced in full. Page 2 of 35 Report No. M2003018-9 Equipment Under Test (EUT) Base station Transmitter Repeater REVISION TABLE Version Sec/Para Change Made Date Changed 1 Initial issue of document 17/06/2020 Except for the Certificate of Compliance, this document must only be reproduced in full. Page 3 of 35 Report No. M2003018-9 CONTENTS 1 Introduction ......................................................................................................................... 5 1.1 Test Facility ................................................................................................................ 5 1.1.1 Company Overview ............................................................................................... 5 1.1.2 NATA Accreditation ............................................................................................... 5 1.2 Test Laboratory/Accreditations .................................................................................. 6 1.3 Units of Measurements .............................................................................................. 6 1.4 Test Equipment Calibration ....................................................................................... 6 1.5 Test Configuration ..................................................................................................... 6 2 Test Procedure ................................................................................................................... 6 2.1 Summary of Test Results .......................................................................................... 6 2.2 General Information ................................................................................................... 7 2.3 Description supplied by Client ................................................................................... 7 2.4 Test sample block diagrams ...................................................................................... 8 2.5 Operating Conditions ................................................................................................. 9 2.6 Modifications .............................................................................................................. 9 3 Conducted Emissions Measurements .............................................................................. 10 3.1 Test Procedure ........................................................................................................ 10 3.2 Peak Maximising Procedure .................................................................................... 10 3.3 Calculation of Voltage Levels .................................................................................. 10 3.4 Plotting of Conducted Emission Measurement Data ............................................... 10 3.5 Test Results ............................................................................................................. 11 3.5.1 AC Mains power ports – Base Station ................................................................. 11 3.5.2 AC Mains power ports – Transmitter ................................................................... 13 3.5.3 AC Mains power ports – Repeater ....................................................................... 15 4 Radiated Emissions Measurements ................................................................................. 17 4.1 Test Procedure ........................................................................................................ 17 4.2 Plotting of Measurement Data for Radiated Emissions ........................................... 17 4.3 Calculation of Field Strength .................................................................................... 17 4.3.1 Test Results 30 – 1000 MHz ............................................................................... 18 4.3.2 Test Results Above 1 GHz Results ..................................................................... 20 5 Compliance Statement ..................................................................................................... 21 6 Measurement Uncertainty ................................................................................................ 22 Appendix A -Test Equipment ................................................................................................... 23 Appendix B - Device Identification Photographs ..................................................................... 24 Appendix C -Test Setup Photographs ..................................................................................... 27 Appendix D – Labelling and User Information Requirements ................................................. 32 Except for the Certificate of Compliance, this document must only be reproduced in full. Page 4 of 35 Report No. M2003018-9 47 CFR PART 15, SUBPART B CERTIFICATE OF COMPLIANCE Device: Smart Foal Home Model Numbers: Base Station: 2.0 Repeater: 1.2 Transmitter: 1.9 Manufacturer: Smart Foal Pty Ltd Tested for: Smart Foal Pty Ltd Address: 40 Gard Road, Mount Cottrell, Vic 3024 Australia Phone Number: 0404905084 Contact: Aimee Nizette Email: [email protected] Standard: 47 CFR Part 15 – Radio Frequency Devices Subpart B – Unintentional Radiators ANSI C63.4: 2014 American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz Result: The Test Sample complied with the applicable FCC Part 15B requirements. Refer to Report M2003018-9 for full details Test Dates: 27th – 28th April, 26th May 2020 Issue Date: 17 June 2020 Attestation: I hereby certify that the device(s) described herein were tested as described in this report and that the data included is that which was obtained during such testing Test Engineers: Ian Paul Ng Bernie Blanco Authorised Signatory: Chris Zombolas Technical Director EMC Technologies Pty Ltd Issued by: EMC Technologies Pty. Ltd., 176 Harrick Road, Keilor Park, VIC, 3042, Australia. Phone: +61 3 9365 1000 E-mail: [email protected] Web: www.emctech.com.au Except for the Certificate of Compliance, this document must only be reproduced in full. Page 5 of 35 Report No. M2003018-9 47 CFR PART 15, SUBPART B TEST REPORT 1 INTRODUCTION This report details the results of ElectroMagnetic Interference (EMI) tests performed on the Smart Foal Home. The measurements were made in accordance with: Federal Communications Commission (FCC) regulations as detailed in Title 47 CFR, Part 15 Subpart B for a Class B device, unintentional radiator. The results and technical details of the test sample are detailed in this report. The test sample was found to comply with the Class B limits for radiated emissions. The test sample was provided by the Client. The results herein apply only to the test sample. 1.1 Test Facility 1.1.1 Company Overview EMC Technologies Pty. Ltd. is an independently owned Australian company that is internationally accredited providing specialist Electromagnetic Compatibility (EMC), Electromagnetic Exposure (EME), Telecommunication and Electrical Safety testing and consultation services to all areas of the electrical and electronics industry. Comprehensive facilities in Melbourne, Sydney, and Auckland (NZ) are supported by over 40 technical specialists and administrative staff. Measurements were performed at EMC Technologies' laboratory in Keilor Park, Victoria Australia. EMC Technologies Pty Ltd has been designated as a Conformity Assessment Body (CAB) by Australian Communications and Media Authority (ACMA) under the APECTEL MRA and is designated to perform compliance testing on equipment subject to Supplier’s Declaration of Conformity (SDoC) and Certification under Parts 15 and 18 of the FCC Commission’s rules – Registration Number 494713 and Designation number AU0001. 1.1.2 NATA Accreditation NATA is the Australian National laboratory accreditation body and has accredited EMC Technologies to operate to the IEC/ISO17025 requirements. A major requirement for accreditation