FIRE FIRE FIRE 4100ES Fire Alarm System Operator’s Manual 579-197 Rev. G 574-xxx Rev. 4 Blank Page- Back of Front Cover Copyrights and Trademarks 2007, 2008, 2011 SimplexGrinnell LP. All rights reserved. Simplex and the Simplex logo are registered trademarks of Tyco International Ltd. and its affiliates and are used under license. Specifications and other information shown were current as of publication and are subject to change without notice. Cautions and Warnings READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in this installation manual. These instructions must be followed to avoid damage to this product and associated equipment. Product operation and reliability depend upon proper installation. ® DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED. Upon unpacking your Simplex product, inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify an authorized Simplex product supplier. ELECTRICAL HAZARD - Disconnect electrical field power when making any internal adjustments or repairs. All repairs should be performed by a representative or authorized agent of your local Simplex product supplier. STATIC HAZARD - Static electricity can damage components. Handle as follows: Ground yourself before opening or installing components. Prior to installation, keep components wrapped in anti-static material at all times. EYE SAFETY HAZARD - Under certain fiber optic application conditions, the optical output of this device may exceed eye safety limits. Do not use magnification (such as a microscope or other focusing equipment) when viewing the output of this device. FCC RULES AND REGULATIONS – PART 15 – This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. SYSTEM REACCEPTANCE TEST AFTER SOFTWARE CHANGES - To ensure proper system operation, this product must be tested in accordance with NFPA72 after any programming operation or change in site-specific software. Reacceptance testing is required after any change, addition or deletion of system components, or after any modification, repair or adjustment to system hardware or wiring. All components, circuits, system operations, or software functions known to be affected by a change must be 100% tested. In addition, to ensure that other operations are not inadvertently affected, at least 10% of initiating devices that are not directly affected by the change, up to a maximum of 50 devices, must also be tested and proper system operation verified. Table of Contents How8B to Use this Publication ............................................................................................ ix Introduction38B ................................................................................................................. ix General39B Conventions .................................................................................................. ix Keyboard40B Conventions ............................................................................................... ix Using41B the Mouse .......................................................................................................... x Chapter 1 0BBasic Concepts and Operations ....................................... 1-1 Introductio42B n .............................................................................................................. 1-1 In43B this Chapter ......................................................................................................... 1-1 Basic9B System Description ............................................................................................ 1-2 Overview4B .................................................................................................................. 1-2 Normal10B Appearance of Operator Interface Panel ........................................................ 1-4 Descriptio45B n ............................................................................................................... 1-4 Chapter 2 1BAlarm Conditions ............................................................... 2-1 Introductio46B n .............................................................................................................. 2-1 In47B this Chapter ......................................................................................................... 2-1 Acknowledging1B an Alarm ............................................................................................. 2-2 How48B the FACP Indicates that an Alarm has Occurred ............................................ 2-2 Overview49B – Acknowledging Alarms ......................................................................... 2-2 Globally50B Acknowledging Alarms .............................................................................. 2-3 Individually51B Acknowledging Alarms ......................................................................... 2-3 Silencing12B an Alarm ....................................................................................................... 2-5 Overview52B .................................................................................................................. 2-5 Using53B the Alarm Silence Key ................................................................................... 2-5 Resetting13B the System .................................................................................................. 2-6 Overview54B .................................................................................................................. 2-6 Resetting5B a System with Active Alarms ................................................................... 2-6 Performing56B a Hardware Reset ................................................................................. 2-7 Disabling14B a Point that Remains in Alarm ..................................................................... 2-8 Overview57B .................................................................................................................. 2-8 Important58B Notes ....................................................................................................... 2-8 Procedure59B ................................................................................................................ 2-8 Chapter 3 2BTrouble Conditions ............................................................ 3-1 Introductio60B n .............................................................................................................. 3-1 In61B this Chapter ......................................................................................................... 3-1 Overview15B ...................................................................................................................... 3-2 How62B the FACP Indicates the Presence of a Trouble ............................................... 3-2 What63B Acknowledge Does......................................................................................... 3-2 Global64B Versus Individual Acknowledge ................................................................... 3-2 Trouble65B Indications for TrueAlarm Sensors ............................................................. 3-3 What6B to Do when TrueAlarm Troubles Occur .......................................................... 3-3 Acknowledging16B Troubles ............................................................................................. 3-4 v Globally67B Acknowledging Troubles ........................................................................... 3-4 Individually68B Acknowledging Troubles ....................................................................... 3-4 If17B the Trouble Doesn’t Clear ......................................................................................... 3-6 Overview69B .................................................................................................................. 3-6 System70B Reset Key ................................................................................................... 3-6 Disabling71B a Point with a Trouble Condition .............................................................. 3-6 Chapter 4 3BSupervisory Conditions ..................................................... 4-1 Introductio72B n .............................................................................................................. 4-1 In73B this Chapter ......................................................................................................... 4-1 Overview18B ...................................................................................................................... 4-2 How74B the FACP Indicates the Presence of a Supervisory Condition ........................ 4-2 What75B Acknowledge Does......................................................................................... 4-2 Acknowledging19B Supervisory Conditions .....................................................................