<p> 18327 version 2 8-Apr-18 1 of 4</p><p>CAN MAKING Set up and monitor an automated can body necking machine</p><p> level: 3 credit: 5 planned review date: November 2009 sub-field: Manufacturing Skills purpose: This unit standard covers the operation of necking machines used to neck one end of a can body. entry information: Open. accreditation option: Evaluation of documentation and visit by NZQA. moderation option: A national moderation system of regional panels and assessor networks has been established by Competenz.</p><p>People credited with this unit standard are able to: perform a setup on; test run and monitor; and perform quality control checks on product from, an automated can body necking machine. special notes: 1 Definitions Key points describe anything that may: result in the success, or otherwise, of a given job; cause injury or damage; or make the task easier to perform. Key steps are actions that must be done, as a logical sequence of an operation, to advance the work. Necking means the necking in of the one end of a can body to allow the stacking of finished assembled components. Product specifications refers to the documented requirements of the manufactured item. Setup, in the context of this unit standard, is synonymous with the term changeover. Either term may be used in the reading and interpretation of this unit standard.</p><p>Ó New Zealand Qualifications Authority 2018 18327 version 2 8-Apr-18 2 of 4</p><p>CAN MAKING Set up and monitor an automated can body necking machine</p><p>Worksite procedures means all documented operational procedures put in place by the candidate’s employer. These include: site safety procedures; equipment operating procedures; standard job procedures; and procedures for the handling and disposal of materials and waste.</p><p>2 All work practices must meet recognised codes of practice and documented worksite safety procedures (where these exceed the code) for personal, product, and worksite safety, and must meet the obligations required under current legislation.</p><p>3 Legislation relevant to this unit standard includes but is not limited to the: Health and Safety in Employment Act 1992; Resource Management Act 1991; Hazardous Substances and New Organisms Act 1996.</p><p>Elements and Performance Criteria element 1</p><p>Perform a setup on an automated can body necking machine.</p><p>Range: one of – size change, component change. performance criteria</p><p>1.1 Necking machine is isolated and locked out in accordance with worksite procedures.</p><p>1.2 Tools and fittings for necking machine setting are identified and selected in accordance with worksite procedures.</p><p>1.3 Setup is explained in terms of sequence, potential safety hazards, and key points for each key step to ensure product conformance to specification.</p><p>1.4 Setup is performed in accordance with worksite procedures.</p><p>Ó New Zealand Qualifications Authority 2018 18327 version 2 8-Apr-18 3 of 4</p><p>CAN MAKING Set up and monitor an automated can body necking machine</p><p>Range: setup includes – necker assembly, necking dies, ejectors. Evidence of two is required.</p><p>1.5 Necking components removed are stored in accordance with worksite procedures. element 2</p><p>Test run an automated can body necking machine and monitor output. performance criteria</p><p>2.1 Raw materials, product, and necker operations are explained in terms of common problems and corrective actions in accordance with worksite procedures.</p><p>Range: common problems may include but are not limited to – dents in body, incorrect cylinder height.</p><p>2.2 Necking machine is test run and monitored in accordance with worksite procedures.</p><p>2.3 Necking machine adjustments are made until necking machine operates in accordance with worksite procedures. element 3</p><p>Perform quality control checks on product from an automated can body necking machine.</p><p>Range: quality control checks to include – necked diameter, cylinder height. performance criteria</p><p>3.1 Quality control checks are performed and recorded in accordance with worksite procedures.</p><p>3.2 Quality control check results are explained in terms of relationships with necking machine settings, product specification tolerances, and variance trends.</p><p>Ó New Zealand Qualifications Authority 2018 18327 version 2 8-Apr-18 4 of 4</p><p>CAN MAKING Set up and monitor an automated can body necking machine</p><p>Comments on this unit standard</p><p>Please contact Competenz [email protected] if you wish to suggest changes to the content of this unit standard.</p><p>Please Note Providers must be accredited by the Qualifications Authority or a delegated inter- institutional body before they can register credits from assessment against unit standards or deliver courses of study leading to that assessment.</p><p>Industry Training Organisations must be accredited by the Qualifications Authority before they can register credits from assessment against unit standards.</p><p>Accredited providers and Industry Training Organisations assessing against unit standards must engage with the moderation system that applies to those standards.</p><p>Accreditation requirements and an outline of the moderation system that applies to this standard are outlined in the Accreditation and Moderation Action Plan (AMAP). The AMAP also includes useful information about special requirements for providers wishing to develop education and training programmes, such as minimum qualifications for tutors and assessors, and special resource requirements.</p><p>This unit standard is covered by AMAP 0013 which can be accessed at http://www.nzqa.govt.nz/site/framework/search.html.</p><p>Ó New Zealand Qualifications Authority 2018</p>