<p> Paint Shaker Safe Work Procedure WSHMS-02C-SWP-108</p><p>Page 1 of 3</p><p>Division: RETSD Analysis By: Kildonan-East Staff Date: Jun/15/2007</p><p>Department: Kildonan-East Collegiate Supervisor: Frequency: Hourly</p><p>Job Title: Auto Body Paint Approved By: JSA Number: ABP5</p><p>Job Title: Paint Shaker ABP5 Job Performed By: Teacher and or students</p><p>REQUIRED PERSONAL PROTECTIVE EQUIPMENT: CSA approved safety glasses or face-shield, CSA approved steel-toed boots/shoes, coveralls, rubber gloves, disposable mask</p><p>GENERAL NOTES: Operators of this machine must be trained by a qualified instructor, demonstrate operational competency and have received pre- operating approval by the instructor of the Body Shop. Operators should be wearing the personal protective equipment recommended above.</p><p>No lighters, matches or cell phones allowed in shop area. Long necklaces and or bracelets are to be removed. Long hair should be tied back. Strings hanging from pullovers/sweaters should be removed or tucked inside pullover/sweater. Hoods from pullovers/sweaters should be tucked inside pullover/sweater or removed.</p><p>Page 1 of 3 Print Date: Jun/15/2007 Paint Shaker Safe Work Procedure WSHMS-02C-SWP-108</p><p>Page 2 of 3</p><p>JOB SAFETY ANALYSIS:</p><p>Step Description Hazard Controls 1 Conduct a pre-operation walk Trip, fall--Suspected malfunction of Good house keeping - clean/clear area of any clutter or spills. around inspection, be aware of machine-- --Report damages to instructor. Do not attempt to operate machine. surrounding to prevent bump injury. --Observe surrounding work area for proper house keeping. Remove all clutter or spills. --Observe condition of paint shaker, check for visible signs of wear. --Report all damages to instructor. Do not attempt to operate a damaged machine. --Observe location of others in or near the area, warn them of paint shaker operation, helpers/observers must always be in view of or behind the operator in a safe location. 2 Place paint can on paint shaker Dropping paint can - foot injury Wear personal protective equipment - CSA safety glasses or face- in between the two metal plates shield, CSA steel-toed safety shoes/boots and rubber gloves. - cradle. --Ensure both ends of paint can are fully within cradle plates. 3 Tighten plates by turning lever Hand or finger placed too close to lever Hold paint can firmly with, one hand under the can/plate and the clockwise until firmly secured. and post - skin or finger pinch. other hand tightening the lever. Do not over-tighten to prevent damaging the paint can. Do not use plastic mixing containers with paint shaker. 4 Turn switch to on position, allow Unprotected, rapid movement/agitation of Hands must be free of machine. -- paint to shake for 2 to 3 paint shaker components. minutes, or as recommended by the manufacturer.</p><p>Page 2 of 3 Print Date: Jun/15/2007 Paint Shaker Safe Work Procedure WSHMS-02C-SWP-108</p><p>Page 3 of 3</p><p>5 If paint shaker becomes noisier Unprotected, rapid movement/agitation of Wait until machine has stopped completely before repositioning and during operation, shut off power paint shaker components. tightening paint can. switch, reposition and retighten paint can. 6 Turn switch to off position. Unprotected, rapid movement/agitation of Hands must be free of machine except button finger. --Wait until paint shaker components. machine has stopped completely before proceeding to next step. 7 Loose clamps by turning lever Hand or finger placed to close to lever Place one hand under the can/plate while loosing the clamps with the counterclockwise and post - skin or finger pinch. --Dropping other. paint can - foot injury 8 Remove paint can from holder. Dropping paint can - foot injury Cradle paint can with both hands and remove from machine.</p><p>AUTHORIZED EMPLOYEE INFORMATION:</p><p>ID NUMBER: LAST NAME: FIRST NAME: REMARKS: JOB HISTORY INFORMATION:</p><p>DATE: REMARKS:</p><p>Approval Signature: Date: </p><p>Page 3 of 3 Print Date: Jun/15/2007</p>