<p> working in partnership to promote quality regulation</p><p>Authorised Person: Job Reference Number: Date of Verification:</p><p>Make Location of Verification: </p><p>Model</p><p>Type</p><p>Class Type Approval Certificate (TAC) No Peripherals etc Test Certificate (TC) No(s)</p><p>Serial No(s) Complies with TAC? Yes  No </p><p>Measures of length | Test Form | Version 3 | 1/4 working in partnership to promote quality regulation</p><p>Inspection Requirements Result Criteria 1. Intelligible Pass  Fail  2. Sufficiently detailed to ensure:  metrological characteristics defined Pass  Fail   the reproducibility of metrological performances of the MML  the integrity of the instrument 3. Includes insofar as is relevant:  a general description of the unit Technical  manufacturing drawings Documentation:  manufacturing procedures to ensure consistent production  descriptions and explanations necessary for understanding the above Pass  Fail   a list of the standards and /or normative documents the MML is required to conform to  descriptions of the solutions adopted to meet the essential requirements where standards/or normative documents have not been applied  results of design calculations, examinations etc 4. Specifies details of markings applied Pass  Fail  Declaration of Conformity  Available and identifiable to each model of MML submitted Pass  Fail  (issued by manufacturer) Certificate of conformity  Issued for each batch (lot) of MML examined, tested and Pass  Fail  (issued by approved notified body)  50, 30, 20, 10, 5, 3, 2, 1.5, 1, 0.5 metre Permitted  1 decimetre Pass  Fail  nominal lengths  1 centimetre Abbreviations  metre m, decimetre dm, centimetre cm, millimetre mm Pass  Fail  Maximum  See schedule 1, paragraph 14 to SI 2006/1267 Permitted Pass  Fail  Errors  MPEs may be marked on the appropriate test comparator  The MML shall maintain an adequate stability of its metrological Durability characteristics over the period of time estimated by the Pass  Fail  manufacturer.</p><p>Measures of length | Test Form | Version 3 | 2/4 working in partnership to promote quality regulation</p><p> The MML to be designed so that any defect has minimal effect on Reliability Pass  Fail  its accuracy or so that such a defect is obvious.  A MML shall have no feature likely to facilitate fraudulent use  The possibility for misuse should be minimal  A MML should be suitable for its intended use and straightforward Suitability Pass  Fail  to use.  A MML shall be robust and its materials of construction suitable to allow it to remain within MPE when in use.  Manufacturer’s mark or name Information to  Information in respect of it’s accuracy (e.g. class ll) be borne by the Pass  Fail   Nominal value and unit of measurement (e.g. 1cm) measure  Identification mark where appropriate  Reference temperature 20°C unless otherwise specified and Reference marked on the MML Pass  Fail  conditions  Tapes of 5m or more shall meet MPE when subjected to 50 N or other force specified/marked  Such that length variations due to temperature changes up to +/- 8 C do not exceed MPE Materials Pass  Fail   MMLs made from materials which are likely to be affected by changes in humidity may only be class II or class III Nominal length  The nominal length (e.g.1m) Pass  Fail  marking  Symbol “CE” as laid down in paragraph 1.B (d) of Annex to CE Marking Decision 93/465/EEC. Pass  Fail   CE mark 5mm high minimum  Capital letter “M” and the last two digits of the year of its affixing, M Mark and surrounded by a rectangle. Pass  Fail  year mark  Height of the rectangle the same as the CE mark.  M marking immediately follow CE marking Notified Body  Notified body number follows the “CE” and the “M” marking Pass  Fail  Mark Location of  The markings shall be clearly visible or easily accessible Pass  Fail  markings  Shall be clear, non-erasable, unambiguous and non-transferable Indelibility of  CE and M markings indelible Pass  Fail  marking  Notified body number indelible or self-destructive upon removal </p><p>STATISTICAL TEST RESULTS FORM</p><p>Measures of length | Test Form | Version 3 | 3/4 working in partnership to promote quality regulation</p><p>Use one form for each group of measures, referred to in the directive as a “homogenous lot”, which can be considered as being the same for the purposes of statistical sampling, i.e., manufactured by the same production process, and belong to the same precision class. (NB. maximum lot size is 10,000) Product Batch No. Declaration of Nominal Type (e.g. Material Number Code Conformity Length (m) tape, folding, Submitted Reference single / double number sided)</p><p>Total number of measures submitted for approval (Lot size) =</p><p>1st sample size 2nd sample size</p><p>1st sample number Incorrect 2nd sample number Incorrect</p><p>Comparator ID</p><p>Pass  Fail  Verification marks applied Yes  No  Serial no. of certificate of conformity / non-conformity where applicable If fail, ‘Rights of Appeal’ notice issued? Yes  No </p><p> dd / mm / yyyy</p><p>Authorised verification officer Date</p><p> dd / mm / yyyy</p><p>Reviewing Officer Date</p><p>Measures of length | Test Form | Version 3 | 4/4</p>