INSTALLATION INSTRUCTIONS Instrucciones de instalación Istruzioni di installazione Installationsanleitung Installatie-instructies Instruções de Instalação Instructions d´installation WM-210SI WM-220SI WM-230SI WM-240SI Dual Stud Short Throw Wall Mounts Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description WM210-220-230-240S/SI WM210-220-230-240S/SI Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and WARNING: Failure to read, thoroughly understand, and subsidiaries (collectively "Milestone"), intend to make this follow all instructions can result in serious personal injury, manual accurate and complete. However, Milestone makes no damage to equipment, or voiding of factory warranty! It is the claim that the information contained herein covers all details, installer’s responsibility to make sure all components are conditions or variations, nor does it provide for every possible properly assembled and installed using the instructions contingency in connection with the installation or use of this provided. product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, WARNING: Failure to provide adequate structural strength regarding the information contained herein. Milestone assumes for this component can result in serious personal injury or no responsibility for accuracy, completeness or sufficiency of damage to equipment! It is the installer’s responsibility to the information contained in this document. make sure the structure to which this component is attached can support five times the combined weight of all equipment. Chief® is a registered trademark of Milestone AV Technologies. Reinforce the structure as required before installing the All rights reserved. component. IMPORTANT WARNINGS AND WARNING: Exceeding the weight capacity can result in CAUTIONS! serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to the short throw projector mounts up to (and including) the projector does not exceed 50 lbs A WARNING alerts you to the possibility of WARNING: (22.68 kg) for the WM210S/SI or WM220S/SI; or 25 lbs serious injury or death if you do not follow the instructions. (11.34 kg) for the WM230S/SI or WM240S/SI. • The weight capacity of the short throw projector mounts CAUTION: A CAUTION alerts you to the possibility of may be LIMITED to the lowest weight capacity of any damage or destruction of equipment if you do not follow the other component located between the short throw wall corresponding instructions. mount and the projector! TABLE OF CONTENTS Disclaimer . 2 WM2XXSI INTERACTIVE MOUNT . 13 Important Warnings and Cautions! . 2 Installing Mount Covers . 13 Table of Contents . 2 Cable Management (Optional) . 14 Dimensions . 3 Removing Mount Covers . 14 Legend . 4 Installation of Wall Bracket Covers . 16 Parts . 5 Adjustments . 17 Site Requirements (WM2XXSI and Security Screw Installation (Optional) . 18 WM2XXS Models) - Steel Stud Structure . 6 WM2XXS STANDARD MOUNT . 21 WS2XXSI Interactive Mount Only . 7 Installing Mount Covers . 21 ASSEMBLY AND INSTALLATION - (WM2XXSI Cable Management (Optional) . 21 and WM2XXS MOUNT MODELS) . 9 Removing Mount Covers . 21 Mounting Wall Bracket . 9 Installation of Wall Bracket Covers . 23 Installation to Wall Bracket . 11 Adjustments . 24 Projector Installation . 12 Security Screw Installation (Optional) . 25 2 Installation Instructions WM210-220-230-240S/SI DIMENSIONS WM2XXS (Standard Model) 240S, TRAVEL 37.2" - 65.6" 210S, TRAVEL 12.75" - 19.5" .75 16.00 .34 3.96 7.25 7.25 10.81 11.53 3 OF 5.64 5.36 19.63 1.42 1.09 CABLE CHANNEL DIMENSIONS: INCHES DIMENSIONS THRU ARM WM2XXSI (Interactive Model) 240SI, TRAVEL 37.2" - 65.6" 19.06 406.40 8.69 210SI, TRAVEL 12.75" - 19.5" .75 16.00 .34 102.87 4.05 184.14 7.25 292.85 3 OF 274.64 11.53 10.81 148.43 5.84 5.36 498.53 19.63 36.12 1.42 27.62 1.09 CABLE CHANNEL DIMENSIONS: [MILLIMETERS] DIMENSIONS THRU ARM INCHES 3 WM210-220-230-240S/SI Installation Instructions LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaien Gat boren Desserrez les fixations Percez un trou Phillips Screwdriver Adjust Destornillador Phillips Ajustar Kreuzschlitzschraubendreher Einstellen Chave de fendas Phillips Ajustar Cacciavite a stella Regolare Kruiskopschroevendraaier Afstellen Tournevis à pointe cruciforme Ajuster Open-Ended Wrench Remove Llave de boca Quitar Gabelschlüssel Entfernen Chave de bocas Remover Chiave a punte aperte Rimuovere Steeksleutel Verwijderen Clé à fourche Retirez By Hand Optional A mano Opcional Von Hand Optional Com a mão Opcional A mano Opzionale Met de hand Optie À la main En option Hex-Head Wrench Security Wrench Llave de cabeza hexagonal Llave de seguridad Sechskantschlüssel Sicherheitsschlüssel Chave de cabeça sextavada Chave de segurança Chiave esagonale Chiave di sicurezza Zeskantsleutel Veiligheidssleutel Clé à tête hexagonale Clé de sécurité 4 Installation Instructions WM210-220-230-240S/SI TOOLS REQUIRED FOR INSTALLATION 3/16" 5/32" (included) (included) (security) 5/32" - 6" long 1/2" (12.7mm) (included) 1/2" (12.7mm) (security) 3/8" (9.5mm) 7/32" (5.6mm) #2 PARTS All Models (WM2XXS Models Only) A (1) [Short throw wall mount] AJ (1) [Upper cover] WM-210 WM-220 WM-230 WM-240 AK (1) [Lower cover] (WM2XXSI Interactive Models Only) All Models X (1) [Cover-top] Y (1) B (1) C (2) D (2) [Interactive cover] [wall bracket] [wall bracket [wall bracket bottom cap] Quick Start top cap] Guide E (2) G (4) AA (4) F (10) 1/4-20 x 3/8" 8-32 x 3/8" 1/4-20 x 5/8" #8-32 x 1/2" Z (1) (security) AB (4) 5/32" 8-32 x 3/8" (security) H (4) AE (1) 1/4-20 x 1-1/2" [Stylus] M (6) J (4) L (4) K (4) 5/16" #10-24 x 1-3/8" [concrete 5/16 x 2-1/2" anchor] AF (4) AD (1) [Stylus AC (1) [AAA battery] [Interactive replacement R (1) S (4) tips] #10-24 x 3/8" software] N (4) P (4) Q (4) 3/16" 1/4-20 x 1-3/4" 1/4" 1/4-20 AH (1) AG (1) [Interactive [Stylus USB cable] W (1) wrist strap Interactive T (2) U (4) 5/32" kit] Software 1/4-20 x 1/2" V (10) 1/4-20 x 3/4" (security) Guide (security) #8-32 x 1/2" (security) (security) 5 WM210-220-230-240S/SI Installation Instructions SITE REQUIREMENTS (WM2XXSI and WM2XXS Models) - Steel Stud Structure WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation. It should also be noted that no other equipment should be mounted to the same stud. (See Figure 1) 16" or 24" (on center) Studs Display Mount Installation Location (Must be centered on stud) If back side of wall is unfinished, drywall must be installed to a minimum of one stud left and right of the stud(s) being used to install the mount. Drywall must be secured to studs with screws 12" on center There must be a minimum of 1-7/8" (48mm) clearance inside wall FRONT Drywall **1/2" minimum Drywall Thickness (Both Sides of Stud) **See hazard statement on page 2! Steel Stud (2 x 4 / 25ga minimum) Stud type and structural strength must conform to the North American Specification for the Design of Cold-Formed Steel Structural Members. [362, 125 18, C-Shape, S - Stud Section] Figure 1 6 WM210-220-230-240S/SI Installation Instructions WS2XXSI INTERACTIVE MODEL ONLY Connection Requirement • The interactive mount includes a USB cable. The Chief Interactive Mount (WM2XXSI) works with standard projectors and Windows® and Macintosh® computers. The Interactive Mount will transform existing whiteboards or other hard, flat surfaces, into interactive whiteboards and allows Screen Recording Requirements users to present, annotate, and interact with their projected (Currently available only on Windows platform.) content and all of their desktop applications. IMPORTANT ! : After adding batteries to the stylus (AE), • Pentium™ IV processor tighten the cap only to the point of being fingertip-tight. • 1.4GHz, with 512MB RAM Overtightening cap may cause the stylus to stop Environmental Interference Guide transmitting signals. Ultrasound Reflections Minimum System Requirements General proximity guideline: A distance of 12 feet • Windows® System (approximately 4 meters) between the motion sensor and the eBeam receiver will normally allow good performance with the • Compatible PC with Pentium™ II 400 MHz+ maximum board size. (See Figure 2) processor and 256 MB RAM • Windows 2000, XP, Server 2003, Vista, or 7 Interference can be reduced by reducing the size of the • 30 MB available hard drive space projection area. • Available USB port • Macintosh® System • Power PC®/Intel™ 1.42 GHz+ processor and 1G RAM • Mac OS X 10.5 through 10.6 • 25 MB available hard drive space • Available USB port Active Capture Area Size • The maximum active capture area supported is: 4 ft x 7 ft or up to 94 inches diagonal measure. • The minimum active capture area supported is: 1.7 ft x 1.1 ft. Motion sensor OK Motion Sensor Free Zone 12 feet Motion sensor Drawing surface Figure 2 7 Installation Instructions WM210-220-230-240S/SI WM2XXSI Placement and Projection Area Constraints (See Figure 3) • There should be a minimum distance of 12 inches between the base of the dual mount and the top of the projection image.