<p>Cutoff Grinder – Rotary Die Cut Off Grinder Safe Work Procedure</p><p>Page 1 of 3 WSHMS-02C-SWP-045</p><p>Division: RETSD Analysis By: Kildonan- Date: Sep/13/2006 East Staff</p><p>Department: Kildonan-East Collegiate Supervisor: Frequency: Hourly</p><p>Job Title: Climate Control Approved By: JSA Number: CC28</p><p>Job Title: Rotary Die Grinder CC28 Job Performed By: Teacher and or stude nts</p><p>REQUIRED PERSONAL PROTECTIVE EQUIPMENT: CSA approved safety glasses or goggles, CSA approved steel-toed footwear, 100% cotton coveralls preferred, and hearing protection required in confined space/area and/or per RETSD policy. If required the use of leather gloves to handle work piece.</p><p>GENERAL NOTES: No lighters, matches or cell phones are allowed in the shop area. Long necklaces, bracelets and rings should be removed. Long hair should be tied back. Strings and hoods hanging from pullovers/sweaters should be removed or tucked inside of coveralls.</p><p>JOB SAFETY ANALYSIS:</p><p>Step Description Hazard Controls 1 Inspect the work area. Be aware 1) Trip, fall, slip. 1) Clean up work area. Practice good housekeeping. of surroundings to prevent 2) Fire, explosion. 2) Remove all flammable or combustible materials prior to starting injury. any work. 1) Observe surrounding work area for proper housekeeping. 2) Remove all clutter, and flammable or combustible materials to ensure a safe work area. 2 Prior to starting project, note Note location of fire extinguisher/s and fire blankets. location of fire extinguisher/s and fire blankets.</p><p>Page 1 of 3 Print Date: Sep/13/2006 3 Inspect die grinder components 1) Flying grinding head. 1) Inspect grinding head. for safe operation. 2) Electrocution. 2) Do not use equipment with damage electrical cord (worn out 1) Inspect grinding head to insulation, or damage receptacle). ensure it is properly secure to the tool. 2) Inspect cord for worn insulation. Do not use with worn insulation. Tag-out and advise instructor or notify instructor right away and ask instructor to Tag-out. 4 Before plugging in the die 1) Possible electrocution (when machine 1) Watch the placement of the electrical cord - keep away from heat grinder, ensure it is in the "off" has stopped and you grab the cord to find and sharp edges that can damage cord. position. out why). 2) Keep the compressed air blowing away from your skin. Wear long 1) Do not route electrical cords 2) Compressed air can cause air bubbles sleeves. near sharp objects and or hot that enter the blood stream. surfaces that may damage the insulation. 2) Compressed Air - do not allow the compressed air to blow toward your skin 5 Energize the die grinder: Rotating grinding wheel. Keep grinding head pointed away from you and others. 1) Ensure that the grinding head Abrasion, Entanglement. is pointed away from you and anyone else in the area. 6 Operate the die grinder. Flying metal shavings. Apply steady, even pressure, ensure safety glasses and or face shield 1) Apply steady, even pressure. Excessive noise. are on. Hearing protection when required per RETSD policy. 7 Do not apply excessive force to Sparks. Do not apply excessive force. Ensure coveralls are 100% cotton the die grinder. May cause it to nothing flammable in coveralls (no lighters, matches). Nothing stall/overheat and create flammable in surrounding area. excessive sparks. 8 Turn die grinder off, unplug and Electrocution. Always unplug electrical tools from the base of the cord. place in its proper storage area. 9 Clean area and remove all waste Trip, fall, slip. Clean up work area and practice good housekeeping. material. Cutoff Grinder – Rotary Die Cut Off Grinder Safe Work Procedure</p><p>Page 3 of 3 WSHMS-02C-SWP-045</p><p>AUTHORIZED EMPLOYEE INFORMATION:</p><p>ID NUMBER: LAST NAME: FIRST NAME: REMARKS: JOB HISTORY INFORMATION:</p><p>DATE: REMARKS:</p><p>Approval Signature: Date: </p><p>Page 3 of 3 Print Date: Sep/13/2006</p>