<p>Honeywell H4W1F 720p WDR TDN Rugged Minidome IP Camera Guide Specifications in CSI Format www.honeywellvideo.com 800-13861V1 Rev A</p><p>SECTION 28 23 29</p><p>H.264 720p WIDE DYNAMIC TRUE DAY/NIGHT RUGGED INDOOR/OUTDOOR MINIDOME IP CAMERA, H4W1F SERIES</p><p>PART 1 GENERAL</p><p>1.1 SECTION INCLUDES</p><p>1.A. Provide a high definition 720p wide dynamic range true day/night rugged indoor/outdoor fixed minidome IP camera system for video surveillance, including design, supply, installation, and commissioning.</p><p>1.2 RELATED SECTIONS</p><p>NOTE TO SPECIFIER: Include related sections as appropriate if video surveillance system is integrated to other systems.</p><p>2.A. Section 26 05 00: Common Work Results for Electrical, for interface and coordination with building electrical systems and distribution.</p><p>2.B. Section 28 05 13: Conductors and Cables for Electronic Safety and Security, for cabling between system servers, panels, and remote devices. </p><p>2.C. Section 28 05 28: Pathways for Electronic Safety and Security, for conduit and raceway requirements.</p><p>2.D. Section 28 23 23: Video Surveillance Systems Infrastructure.</p><p>2.E. Section 28 23 29: Video Surveillance Remote Devices and Sensors.</p><p>1.3 REFERENCES</p><p>3.A. Reference Standards: Provide systems that meet or exceed the requirements of the following publications and organizations as applicable to the work of this Section.</p><p>28 23 29-9 Honeywell H4W1F 720p WDR TDN Rugged Minidome IP Camera Guide Specifications in CSI Format www.honeywellvideo.com 800-13861V1 Rev A</p><p>3.A.1. Canadian ICES-003.</p><p>3.A.2. Canadian Standards Association (CSA).</p><p>3.A.3. Conformity for Europe (CE).</p><p>3.A.4. Electronic Industry Association (EIA).</p><p>3.A.5. Federal Communications Commission (FCC).</p><p>3.A.6. Joint Photographic Experts Group (JPEG).</p><p>3.A.7. National Television Systems Committee (NTSC).</p><p>3.A.8. Phase Alternating Line (PAL).</p><p>3.A.9. Underwriters Laboratories Inc. (UL).</p><p>1.4 SYSTEM DESCRIPTION</p><p>4.A. The 720p wide dynamic true day/night rugged minidome IP camera shall use a compact, one-piece, vandal-resistant enclosure that can be mounted directly to, or recessed into, a ceiling, wall, or 4S electrical box. An optional wall/pendant mount kit shall also be available.</p><p>4.B. The 720p wide dynamic true day/night rugged minidome IP camera shall provide 720p (1280 × 720) resolution, a 1/3-inch progressive scan CMOS sensor with wide dynamic range and true day/night functionality, H.264 (primary stream) and H.264/MJPEG (secondary stream) compression formats, and ONVIF support.</p><p>1.5 SUBMITTALS</p><p>5.A. General: Submittals shall be made in accordance with the Conditions of the Contract and Submittal Procedure Section. </p><p>5.B. Manufacturer’s Product Data: Submit manufacturer’s data sheets indicating systems and components proposed for use, including instruction manuals.</p><p>5.C. Shop Drawings: Submit installation drawings, including connection diagrams for interfacing equipment, list of connected equipment, and locations for major equipment components. Shop drawings shall indicate surrounding construction as provided for the Project.</p><p>5.D. Project Record Drawings: Indicate location of equipment and wiring on project record drawings. Submit an electronic version of the project record drawings not later than Substantial Completion of the Project.</p><p>28 23 29-9 Honeywell H4W1F 720p WDR TDN Rugged Minidome IP Camera Guide Specifications in CSI Format www.honeywellvideo.com 800-13861V1 Rev A</p><p>5.E. Operation and Maintenance Data: Submit manufacturer’s operation and maintenance data customized to the system installed. Include operator manuals.</p><p>5.F. Field Tests: Submit results of field testing of every device, including date, testing personnel, retesting date (if applicable), and confirmation that every device passed field testing.</p><p>5.G. Maintenance Service Agreement: Submit a sample copy of the manufacturer’s maintenance service agreement, including cost and services for a one year period for Owner’s review. Maintenance shall include, but not be limited to, labor and materials to repair the system, tests and adjustments, and regular inspections.</p><p>1.6 QUALITY ASSURANCE</p><p>6.A. Qualifications: Manufacturers shall have a minimum of 10 years full time experience in manufacturing and maintaining video surveillance systems. Manufacturer shall provide toll- free technical assistance and support available 24/7. Installers shall have a minimum of 2 years experience installing similar systems and shall be acceptable to the manufacturer of the video surveillance system.</p><p>6.B. Regulatory Requirements: </p><p>1.A.1. Emissions: FCC, Part 15; EN 55022.</p><p>1.A.2. Immunity: EN 50130-4.</p><p>6.B.1. Safety: UL/CSA 60950-1; EN 60950-1. </p><p>1.7 DELIVERY, STORAGE, AND HANDLING</p><p>7.A. Packing and Shipping: Deliver products in manufacturer’s labeled packages.</p><p>7.B. Storage and Protection: Store and handle products in accordance with manufacturer’s requirements in facility where environmental conditions are within recommended limits.</p><p>1.8 PROJECT CONDITIONS</p><p>8.A. Environmental Requirements: Comply with environmental requirements and recommendations of manufacturer for proper installation of products.</p><p>8.B. Temperature Criteria: </p><p>8.B.1. Operating temperatures shall be between −13° F (−25° C) and 131° F (55° C). </p><p>28 23 29-9 Honeywell H4W1F 720p WDR TDN Rugged Minidome IP Camera Guide Specifications in CSI Format www.honeywellvideo.com 800-13861V1 Rev A</p><p>8.B.2. Storage temperatures shall be between −40° F (−40° C) and 158° F (70° C).</p><p>8.C. Power Requirements: Input voltage shall be 24 V AC or PoE IEEE 802.3af.</p><p>1.9 WARRANTY</p><p>9.A. Manufacturer’s Guarantee: Three (3) years from the manufacture date code under normal use and service for the video surveillance system.</p><p>PART 2 PRODUCTS</p><p>2.1 MANUFACTURERS</p><p>1.A. Specified Manufacturer: Honeywell, www.honeywellvideo.com or www.honeywellintegrated.com</p><p>1.B. Accepted Part Numbers:</p><p>1.B.1. H4W1F1.</p><p>1.B.2. H4W1F1X.</p><p>2.2 SYSTEM COMPONENTS</p><p>2.A. Specified Product: Honeywell H4W1F 720p WDR TDN rugged minidome IP camera.</p><p>2.B. Cabling.</p><p>2.3 OPERATIONAL REQUIREMENTS</p><p>3.A. The 720p wide dynamic true day/night rugged minidome IP camera system shall meet or exceed the following camera specifications:</p><p>3.A.1. Image Sensor: 1/3-inch CMOS.</p><p>3.A.2. Total Pixels: 1280 (H) × 720 (V). </p><p>3.A.3. Lens Type: </p><p>28 23 29-9 Honeywell H4W1F 720p WDR TDN Rugged Minidome IP Camera Guide Specifications in CSI Format www.honeywellvideo.com 800-13861V1 Rev A</p><p>3.A.3.a. H4W1F1(X): True Day/Night (TDN) 3.3–12 mm, varifocal auto iris, F1.6.</p><p>3.A.4. Horizontal Angle of View: 89.8° at wide end, 23.9° at tele end.</p><p>3.A.5. Minimum Illumination: 0.14 lux color, 0.1 lux b/w @ 50 IRE, F1.6.</p><p>3.A.6. Automatic Electronic Shutter Speed: 1/30 to 1/87,000 seconds.</p><p>3.A.7. Video Output: Composite, 1.0 VP-P, 75 ohms.</p><p>3.A.8. White Balance: Auto White Balance Control (Auto), Manual, WBC Push.</p><p>3.A.9. Signal-to-Noise Ratio: 50 dB or higher (AGC off).</p><p>3.A.10. Synchronization: Internal.</p><p>3.B. The 720p wide dynamic true day/night rugged minidome IP camera system shall provide true day/night functionality with an infrared (IR) cut filter for day mode.</p><p>3.C. The 720p wide dynamic true day/night rugged minidome IP camera system shall provide 3D digital noise reduction, electronic light compensation, automatic light compensation, automatic gain control, flickerless mode, and digital slow shutter.</p><p>3.D. The 720p wide dynamic true day/night rugged minidome IP camera system shall provide, in high contrast lighting conditions, higher quality images and significantly better dynamic range (>100 dB) than conventional IP cameras.</p><p>3.E. The 720p wide dynamic true day/night rugged minidome IP camera system shall provide fully configurable motion detection settings.</p><p>3.F. The 720p wide dynamic true day/night rugged minidome IP camera system shall support ONVIF specification for interoperability between network video products.</p><p>3.G. The 720p wide dynamic true day/night rugged minidome IP camera system shall support remote firmware updates.</p><p>3.H. The 720p wide dynamic true day/night rugged minidome IP camera system shall support HTTP, TCP, RTSP, RTP, UDP, ARP, DNS, NTP, RTCP, FTP, ICMP, DHCP, Bonjour, IGMP, and SSH protocols.</p><p>3.I. The 720p wide dynamic true day/night rugged minidome IP camera system shall provide dual H.264 and/or H.264/MJPEG video streams. It shall also provide controllable frame rates and bandwidth and constant or variable bit rates.</p><p>3.J. The 720p wide dynamic true day/night rugged minidome IP camera system shall provide Network Time Protocol (NTP) synchronization support.</p><p>28 23 29-9 Honeywell H4W1F 720p WDR TDN Rugged Minidome IP Camera Guide Specifications in CSI Format www.honeywellvideo.com 800-13861V1 Rev A</p><p>3.K. The 720p wide dynamic true day/night rugged minidome IP camera system shall support embedded date/time stamps in the video stream.</p><p>3.L. The 720p wide dynamic true day/night rugged minidome IP camera system shall support Internet Explorer 8 and 9, Mozilla Firefox®, and Google Chrome web browsers.</p><p>3.M. The 720p wide dynamic true day/night rugged minidome IP camera system shall support input and output alarm contacts and bidirectional audio.</p><p>3.N. The 720p wide dynamic true day/night rugged minidome IP camera system shall provide an RJ45 connection and a second video service connector (2-pin Molex).</p><p>3.O. The 720p wide dynamic true day/night rugged minidome IP camera system shall provide 24 V AC or PoE IEEE 802.3af options.</p><p>3.P. The 720p wide dynamic true day/night rugged minidome IP camera system shall have a 3- axis (pan/tilt/rotation) gimbal bracket for precise camera positioning.</p><p>3.Q. The 720p wide dynamic true day/night rugged minidome IP camera system shall instantly convert to flush or surface mount for mounting to a ceiling, wall, or 4S electrical box.</p><p>3.R. The 720p wide dynamic true day/night rugged minidome IP camera system housing shall consist of die-cast aluminum with a cool gray powder coat finish, and the bubble shall consist of impact-resistant 1.5 mm-thick polycarbonate resin..</p><p>2.4 SYSTEM HARDWARE</p><p>4.A. The 720p wide dynamic true day/night rugged minidome IP camera system shall have the following mechanical specifications: </p><p>4.A.1. Unit Dimensions (W x H): 6.1 × 4.6 inches (156.0 × 117.1 mm).</p><p>4.A.2. Unit Weight: 3 lb (1.3 kg) camera only.</p><p>4.A.3. Connectors:</p><p>4.A.3.a. Network: RJ45 connector.</p><p>4.A.3.b. Aux Video Output: 2-pin Molex connector.</p><p>4.A.3.c. Power Input: Removable screw block.</p><p>4.A.3.d. Alarm I/O: Removable screw block.</p><p>4.A.3.e. Audio In: Removable screw block.</p><p>4.A.3.f. Audio Out: Removable screw block.</p><p>28 23 29-9 Honeywell H4W1F 720p WDR TDN Rugged Minidome IP Camera Guide Specifications in CSI Format www.honeywellvideo.com 800-13861V1 Rev A</p><p>4.B. The 720p wide dynamic true day/night rugged minidome IP camera system shall have the following electrical specifications:</p><p>4.B.1. Voltage: 24 V AC or PoE IEEE 802.3af.</p><p>4.B.2. Power Consumption:</p><p>4.B.2.a. 24 V AC: 5.0 watts max.</p><p>4.B.2.b. PoE: PD Type 1 Class 2.</p><p>4.C. The 720p wide dynamic true day/night rugged minidome IP camera system shall be designed to meet the following environmental conditions:</p><p>4.C.1. Operating temperature: −13° F (−25° C) and 131° F (55° C). </p><p>4.C.2. Storage temperature: −40° F (−40° C) and 158° F (70° C).</p><p>4.C.3. Ingress Protection Rating: IP66.</p><p>4.C.4. Relative Humidity: 0–85%, non-condensing.</p><p>4.C.5. Emissions: FCC, Part 15; EN 55022.</p><p>2.5 MANUFACTURER SUPPORT</p><p>5.A. Manufacturer shall provide customer service, pre-sales applications assistance, after-sales technical assistance, access to online technical support, and online training using Web conferencing. </p><p>5.B. Manufacturer shall provide 24/7 technical assistance and support by means of a toll-free telephone number at no extra charge.</p><p>PART 3 EXECUTION</p><p>3.1 EXAMINATION</p><p>28 23 29-9 Honeywell H4W1F 720p WDR TDN Rugged Minidome IP Camera Guide Specifications in CSI Format www.honeywellvideo.com 800-13861V1 Rev A</p><p>1.A. Examine site conditions prior to installation. Notify Architect and Owner in writing if unsuit- able conditions are encountered. Do not start installation until site conditions are accept- able.</p><p>3.2 INSTALLATION</p><p>2.A. All components of the camera system shall be thoroughly tested before shipping to the project location.</p><p>2.B. Camera system shall be installed, programmed, and tested in accordance with manufacturer’s instructions and recommendations.</p><p>2.B.1. Coordinate interfaces with other products with Owner’s representative where appropriate.</p><p>2.B.2. Provide conduit, cable, and wire for complete and reliable installation. Obtain Owner’s approval for exact location of cameras, boxes, conduit, cable, and wiring runs prior to installation.</p><p>2.B.3. Install conduit, cable, and wire parallel and square with building lines, including raised floors areas. Do not exceed 40 percent fill in conduits. Gather and tie wires for orderly installation.</p><p>2.B.4. Coordinate with other trades to provide proper sequencing of installation.</p><p>3.3 FIELD COMMISSIONING AND CERTIFICATION</p><p>3.A. Field Commissioning: Test bullet camera system as recommended by manufacturer, including the following:</p><p>3.A.1. Conduct complete inspection and testing of equipment, including verification of operation with connected equipment. </p><p>3.A.2. Test devices and demonstrate operational features for Owner’s representative and authorities having jurisdiction, as applicable.</p><p>3.A.3. Correct deficiencies until satisfactory results are obtained.</p><p>3.A.4. Submit written copies of test results.</p><p>3.4 TRAINING</p><p>28 23 29-9 Honeywell H4W1F 720p WDR TDN Rugged Minidome IP Camera Guide Specifications in CSI Format www.honeywellvideo.com 800-13861V1 Rev A</p><p>4.A. Conduct on-site system administrator and security/surveillance operator training in accordance with the manufacturer’s instructions and recommendations. Training shall include, but not be limited to: camera administration, provisioning, configuration, operation, and diagnostics.</p><p>END OF SECTION</p><p>28 23 29-9</p>