Electric Currents and Simple Circuits

I-1Electric Currents and Simple CircuitsElectrons can flow along inside a metal wire if there is an E-field present to push them along (   F= q E ). The flow of electrons in a wire is similar to the flow of water in a pipe.DQ Definition: electric current I = = rate of flow of charge Dt units [ I ] = coulomb/second = 1 C / 1 s = 1 ampere (A) = "amp""It's not the voltage that kills you, it the amps." About 0.05 A is enough to kill you. If current I = 1 A in a wire, then 1 coulomb of charge flows past any point every second. I In electrostatic problems, E= 0 inside a metal, but if I  0, then the situation is not static, the E-field is not zero. Electrons flow in metals, not protons, so (–) charges are moving when there is a current. The r r electron feel a force F= - e E and goes E "upstream" against the E-field.The flow of (–) charge in one direction is electrically equivalent to the flow of (+) charge in the opposite direction: neutral either way, + + + + () or (+) plates get:    Last update: 4/4/2018 Dubson Phys2020 Notes, University of Colorado I-2By convention, we define current I as the flow of imaginary (+) charges, when it is really (–) charges flowing the other way: I(Some texts refer to I as the "conventional current" to distinguish it from the "electron current".)Example: How many electrons flow past per second when the current is 1 A? DQ D N譊 e N I 1 A 1C / s 18- 1 I= =� = =-19 = - 19 5.6 10 s Dt D t D t e 1.6创 10 C 1.6 10 CAbout 0.01 A = 10 mA flowing though your heart is lethal, yet I could grab a wire carrying 1000A and be safe! Why? Because my body has a much higher electrical resistance than the metal. The electrons prefer to flow through the metal wire.For most materials, the current I is proportional to the voltage difference between the ends. r r I礑 E (since F = q E) and V 档 E, so I D V hi V lo V E IV From now on, we usually follow the (bad) convention and write "V" when we really mean "V". V I档 V ( really I D V)� constant I V Definition of resistance R (of a piece of wire or other material): R I The experimental fact that (for most materials) the ratio R = V / I is a constant, independent of V or I, is called V Ohm's Law : R= = constant , usually written V = I R (R constant) I Units: [R] = volt / ampere = ohm () ["" is Greek letter omega]Last update: 4/4/2018 Dubson Phys2020 Notes, University of Colorado I-3Ohm's Law should be written V = I R, but the bad convention is to write V = I R. "Ohm's Law" is not really a law, because it is not always true. For many materials, Ohm's Law is approximately true, the resistance R is approximately constant, independent of V or I. Materials that obey Ohm's Law are called "ohmic materials". But some materials are "non- ohmic"; they do not obey Ohm's Law. The average speed of electrons in a current-carrying wire results from a competition between two r r r effects: (1) the E-field, which causes an acceleration according to F= q E = m a , making the electrons go faster and faster, and (2) the scattering of electrons due to impurities and thermal vibrations, which act like friction, making the electrons slow down.For typical currents in real wires, the average electron speed (often called the drift velocity) is actually quite slow, typically less than 0.1 mm/s. (Incidentally, the term drift velocity is incorrect, it should be called the drift speed.)A material with lots of electron scattering has a high resistance:5 Rwire << 1 , Rhuman  10  V 10V - 4 I= =5 = 10 A (harmless) R 10 W  10 V safe, 100 V dangerous ! V 100V - 3 I= =5 = 10 A (painful!) R 10 WThe resistance R of a piece of material depends on its shape and composition. Shape: long and skinny  R big short and fat  R small — just like the flow of water through a pipe. Long skinny water pipes resist flow of water. L Turns out that R , L A area A so big L means big R, big A means small RLast update: 4/4/2018 Dubson Phys2020 Notes, University of Colorado I-4 r L R =  (Greek letter "rho") = resistivity A ( We show were this comes in the next section below.) Resistivity  depends on the material composition, not on the shape.  is a measure of the scattering of electrons in that material, like viscosity of fluid in a pipe. Big  means lots of scattering (friction), big resistance to flow. A r = R Units: {L [  ] = [R]  length = m length length length material  use Cu 1.7  10-8 m house wiring Al 2.7  10-8 m power lines W (tungsten) 5.3  10-8 m (cool) light bulb filaments 60  10-8 m (hot) Fe 9.8  10-8 m not used in wiring glass 10+10 m electrical insulatorMicroscopic view of Ohm's Law. I Definition: current density J = (current per area in a conductor). We also define current A density vector J where direction of J is the direction of the current.J is related to the average speed vdrift of the charge carriers (usually electrons) by J = n q vdrift , n is the number of carrier per volume, q is the charge per carrier (usually q = e). Proof: Consider a wire with carrier density n (#/volume), cross-sectional area A, and drift speed vdrift. In a time t, all the charges move an average distance x = vdrift t. area A volume = A  xJx = v t Last update: 4/4/2018 Dubson Phys2020 Notes, Universitydrift of Colorado I-5The charge Q in the length of wire x is number of carriers charge DQ= 创 volume = n q A D x volume carrierID Q 1 n q A D x So the current density is J= =� = n q vdrift Done. AD t A A D tIn ohmic materials, the current density J is proportional to the electric field E v v J= s E , where the proportionality constant  is called the conductivity. 1 The resistivity  is defined as r = and so E =  J. s J= s E or E= r J , where  = 1/ = constant is the microscopic version of Ohm's Law. We now show that this is equivalent to V = I R : Consider a cylindrical section of conductor, length L, cross-sectional area A, with current density J, and E-field E.Start with E= r J , now multiply both sides by L and write A J, E I J as J = I / A.  E L= r L . Notice that V = E L. A L r L So we have DV= I , or DV= I R , where we A r L have defined the resistance R as R = . We have just shown that E= r J is the same as A r L Ohm's Law V = I R, where R = . ALast update: 4/4/2018 Dubson Phys2020 Notes, University of Colorado I-6A Simple Circuit Some electrical circuits symbols:R C resistor capacitor switch battery E or V(–) side (+) sideA battery's job is to maintain a constant voltage difference between its terminals. It acts like a charge pump, pushing (+) charge inside the battery from the (–) side to the (+) side. This is the direction that the charges don't want to go. The battery has to do chemical work to push the charges "uphill" (toward higher electrostatic PE)."10-volt battery" means voltage across battery = E or V (or just V) = 10 volts = 10 V. Hence the confusing equation: V = 10 V, meaning "the voltage difference across battery is 10 volts". switch open switch closed V = +10V V = +10V R = 50  V battery I R (carbon V = 0V resistor) wire V = 0VAlways assume that the wires connecting circuit elements have zero resistance Rwire = 0  no voltage change along the wire, since Vwire = I Rwire = I  0 = 0.V 10V Current around the circuit is: I= = = 0.2A R 50WRecall that (+) charge tends toward low voltage. Can think of voltage as a kind of "electrical pressure". Water in a pipe flows from high pressure to low pressure. Likewise, (+) charges in a wire flow from hi V to lo V. In the water-pipe analogy, we can think of a resistor as like a porous plug of gravel in the pipe. The gravel plug offers resistance to the flow of water, so we need a large pressure difference to push the water through.Last update: 4/4/2018 Dubson Phys2020 Notes, University of Colorado I-7If no pressure difference across a pipe plug, then no water flows. If no voltage difference across a resistor, then no current flows. I flow hi V lo V hi P lo P gravel plug in water-filled V = V = I R pipe Inside a resistor, (+) charge flows from hi V  lo V ("downhill") Inside a battery, (+) charge flows from lo V  hi V ("uphill"). Current I is the same in the battery and the resistor, just as water flow (in gallons per minute) is same through pump and through gravel plug. hi pressure hi VPump gravel V I R lo pressure lo VElectrical Power When I is big, R gets hot because the flowing electrons are scattered  friction. Recall that power P = rate at which energy is transformed = rate at which work is doneW joule P D , [ P]= = 1 watt (W) Dt secondIn a resistor, the rate at which electrostatic PE is converted into thermal energy (heat) is P = I V ( really, P = I V )If I = constant, then the average speed of electrons is constant  KE = (1/2)mv2 = constant.Last update: 4/4/2018 Dubson Phys2020 Notes, University of Colorado I-8When an amount of charge Q flows through a resistor in a time t, from the high V side to the low V side, the change in PE of that charge is PE = Q V. The PE of the charge Q is decreased, but KE = constant. Where did the energy go? Answer: into thermal energy PE骣 Q P=D =譊 V = I V 桫 { t{ t V IP = I V and V = I R  P = I ( I R ) = I2 R or P = (V / R) V = V2 / R V2 3 equivalent expressions for power: P= I V = I2 R = R"100 W bulb" uses P = 100 W. Light bulbs and most other appliances (TV, coffee grinder) are designed to work with voltage V = 120 V (really V = 120 V). example of electrical power: What is the current through a 100 W light bulb? What is its resistance (when on and hot).2 P 100 W V2 V 2 (120V) I= = = 0.83A , P=� R = = W 144 V 120V R P 100 WLast update: 4/4/2018 Dubson Phys2020 Notes, University of Colorado

Electric Currents and Simple Circuits

Details

Download

Copyright

We respect the copyrights and intellectual property rights of all users. All uploaded documents are either original works of the uploader or authorized works of the rightful owners.

Support