080303-1 Part Number: LEX-202-03 INSTALLATION INSTRUCTIONS LEXUS LX 470 (2003-2007) TOYOTA LAND CRUISER (2003-2007) SEE REVERSE SIDE FOR LEXUS RX330, RX350, RX400 AND LEXUS RX HYBRID (2006) NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT. All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break. Logo and part number will be right side up and readable when installed. TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), one 5/64” drill bit and hand drill, #2 Phillips screwdriver, protective cloth. marking pen. PARTS INCLUDED: One Custom Bezel Mount, instructions and one (1) #8x1/2” screw. LOCATION: To the Right of the Radio Step 1. FOR LEXUS LX470, Skip step #1 and moved to step #2 On the 2003 Toyota Land Cruiser, begin by removing the air vent and bezel on the right side of the radio using the Dash Trim tool. Insert the Dash Trim tool behind the upper right corner to release the first clip, working the remaining clips loose. Disconnect all wiring and set the bezel aside. Move to step #3 Step 2. On the Lexus LX 470, use the Dash Trim Panel tool to remove the bezel that surrounds the tape player and radio. Note: See the first picture. Work the top of the bezel loose, then continue with the bottom of the bezel where there are three plas- tic clips to release. These clips can be hard to loosen so be careful. Move the bezel out of the way. Move to step #4 Step 3. On the Toyota Land Cruiser, use the #2 Phillips screwdriver and remove the four (4) bolts that hold the radio in place. Set the screws aside. Set the emergency brake and shift the transmission into first gear. Lift the radio out and set it on a soft protective cloth on the console area. Step 4. Place the Custom Bezel Mount on the flat spot just below the center clip hole on the right side of the cavity. Use the hole in the mount as a guide to mark a spot for drilling a pilot hole. Set the mount aside. Use the 5/64” drill bit and hand drill to create a pilot hole. Place the mount back over the flat spot aligning the pilot hole and the hole in the mount. Insert the provided screw and tighten the mount down in place. Note: The tight fit between the bezel and the dash pad will provide additional support for the mount. Reinstall the dash in reverse order securing all components. Install any Bracketron phone holder or Amps compatible device to your Bezel Mount. Your installation is complete. Always check our website for the most updated model year compatibility information. compatibility year model updated most the for website our check Always © Bracketron Inc, 2007 All rights reserved. The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information. Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount. Bracketron Inc 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: 952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443 Web Address: www.bracketron.com 080303-1 Part Number: LEX-202-03 INSTALLATION INSTRUCTIONS LEXUS RX 330 & RX330H (2004-2006) LEXUS RX350 & RX350H (2007) LEXUS RX400 & RX400H (2006-2007) NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT. All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break. Logo and part number will be right side up and readable when installed. TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), one 5/64” drill bit and hand drill, #2 Phillips screwdriver, marking pen. PARTS INCLUDED: One Custom Bezel Mount, instructions and one (1) #8x1/2” screw. LOCATION OF MOUNT: To the right of the gear shifter.. Step 1. Insert the Dash Trim Tool in the lower left corner of the gear shifter bezel and carefully pry upward to release the first clip. Work the rest of the bezel loose with the trim tool releasing the remian- ing three (3) clips. Set the bezel aside. Step 2. Locate the upper right clip hole to the right of the gear shifter. Locate a flat area just below the clip hole. Place the mount on this flat spot and use a marking pen to mark a spot to drill a pilot hole, using the hole in the mount as a guide. When the pilot hole is drilled place the mount over the hole aligning the hole in the mount with the pilot hole. Insert the provided screw and tighten down the mount with the Phillips screwdriver. Step 3. Reinstall the gear shifter bezel securing the four clips that hold it in place. Install any Bracketron phone holder or Amps compatible device to your Bezel Mount. Your installation is complete. Always check our website for the most updated model year compatibility information. compatibility year model updated most the for website our check Always © Bracketron Inc, 2007 All rights reserved. The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information. Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount. Bracketron Inc 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: 952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443 Web Address: www.bracketron.com 100504-1 Part Number: LEX-202-03 INSTALLATION INSTRUCTIONS LAND ROVER FREELANDER (2002-2003) NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT. All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break. Logo and part number will be right side up and readable when installed. TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), #2 Phillips screwdriver. PARTS INCLUDED: One Custom Bezel Mount, instructions and one (1) #8x1/2” screw included but not needed for Freelander. LOCATION OF MOUNT: To the right of the climate control. Step 1. Grasp the three climate control knobs with your fingers tightly. Carefully pull toward you to remove the knobs. Set the knobs aside in a safe place. Locate two Phillips screws behind the left and right climate control knobs. Remove these screws with your #2 Phillips screwdriver and set aside. Step 2. Phillips Screws Insert the Dash Trim Tool in the lower left corner of the climate control bezel and pry toward you to release the first clip. Work the rest of the bezel loose. There are a total of four clips, two on each side of the bezel. Set the bezel aside. Step 3. Locate and remove the top right screw that holds the climate control. Place the Custom Bezel Mount over this screw hole and insert the factory screw and tighten the mount down in place. Reinstall the climate control bezel securing the four clips and two screws that hold it in place. Install any Bracketron phone holder or Top Right Screw Amps compatible device to your Custom Bezel Mount. Your installation is complete. Always check our website for the most updated model year compatibility information. compatibility year model updated most the for website our check Always © Bracketron Inc, 2007 All rights reserved. The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information. Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount. Bracketron Inc 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: 952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443 Web Address: www.bracketron.com.