Streamline® Bumper INSTALLATION INSTRUCTIONS Step 3: Installing Bumper E Snap bumper onto base, either by using your hands or a rubber mallet. NOTE: Cover mallet with a cloth so that you do not mar the bumper finish. Adjust bumper so it is centered on the base. E F Side View In the Box Tools Required n 1 x Streamline Bumper Top n #8 x 1" Screws n 2 x Hidden Endcaps n Drill with Phillips Driver Bit n 1 x Bumper Base n Tape Measure n Radial Arm Saw n Chalkline or Pencil n Rubber Mallet (optional) SECTION E-E SCALE 1 : 1 Questions? Call McCue Customer Service at 800.800.8503 ©2014 McCue Corporation, 13 Centennial Drive Peabody, MA 01960, USA. www.mccue.com F SECTION F-F SCALE 1 : 1 Thursday, June 05, 2014 Cutting the Base - 1" Profile (GGB-10AS) 9 Cut base 2 16" shorter than top piece length X 9 X - 2 16 " 1 Cutting the Base Thursday, June 05, 2014 Thursday, April 17, 2014 9 Cutting the Base - 1" Profile (GGB-10) Cut base 2 /16" shorter than top piece length Cutting the Base - 1" Profile (GGB-10AS) 9 Cutting the Base - 2" Profile (GGB-20) Cut baseCutting 3¾" the shorter Base - 2" thanProfileCut top (GGB-20AS) base piece 2 16" shorter length than top piece length Cutting the Base - 1" Profile (GGB-10AS) 3 9 Cut base 3 4" shorter than top piece length Cut base 2 16" shorter than top piece length 18" X X 7 15 16 " 9 3 X - 16 Cutting the Base - 2" Profile X(GGB-20AS) - 3 4 " 2 " 1 Cut base 3 2" shorter than top piece length 16" Cutting the Base - 2" Profile (GGB-20AS) 3 Cut base 3 4" shorter than top piece length 1 12 2 " Marking the Case X Use a tape measure and chalk line (or pencil) to mark a line on the case where the top of the bumper will be placed 2 Marking the Case (based on your bumper height specification) Marking the Case Use a tape measure and chalk line (or pencil)Step 1: to Installing mark a Anti-Shunting line on Usethe aEndcaps tapecase measure where to and Base chalk the line top(or pencil) of tothe mark bumper a line on the casewill where be the place. top of the bumper will be placed 3 X - 3 4 " Snap one anti-shunting endcap(based to on each your bumper end of height each specification) length of base to be installed. The tab on the anti-shunting endcaps should slide into the track of the base for a snug fit. Step 1: Installing Anti-Shunting Endcaps to Base Snap one anti-shunting endcap to each end of each length of base to be installed. The tab on the anti-shunting endcaps should slide into the track of the base for a snug fit. 3 Installing Hidden Endcaps to Base Marking the Case Snap one hidden endcap to each end of each length of Use a tape measure and chalk line (or pencil) to mark a line on the case where the top of the bumper will be placed (based on your bumper heightbase specification) to be installed. Step 1: Installing Anti-ShuntingThe Endcapstab on theto Base hidden endcaps should slide into the track of Snap one anti-shunting endcapthe base to each for end a ofsnug each fit. length of base to be installed. The tab on the anti-shunting Thursday, April 17, 2014 C endcaps should slide into the track of the base for a snug fit. 4 Installing the Base+Endcap Assembly Line up the top of the base with the penciled line on the case. Using a drill with a Phillips driver bit, attach the base and endcap assembly to the mounting surface by placing #8 x 1" screws in the endcap screw holes DO NOT over tighten screws. Thursday, April 17, 2014 C DETAIL A SCALE 1 : 1 A Step 2: InstallingStreamline® the Base+Endcap Assembly Bumper | Page 2 of 3 Line up the top of the base with the penciled line on the case. Using a drill with a Phillips driver bit, attached the Base+Endcap Assembly to the mounting surface by placing #8 x 1 sheet metal screws in the endcap screw holes. DO NOT over tighten screws. DETAIL A SCALE 1 : 1 A Step 2: Installing the Base+Endcap Assembly Line up the top of the base with the penciled line on the case. Using a drill with a Phillips driver bit, attached the Base+Endcap Assembly to the mounting surface by placing #8 x 1 sheet metal screws in the endcap screw holes. DO NOT over tighten screws. Thursday, April 17, 2014 Thursday, April 17, 2014 4" Thursday, April 17, 2014 5 Installing the Base Fix the base to the mounting surface by placing #8 x 1" screws in the screw guide 4" holes (Figure A) of the base every 4 inches. Screw guide hole Begin by measuring 4" from the inside 4" endcap screw that goes through the base Figure A and the endcap. This screw measures ¼" Step 2b: Installing the Base Fix the base to the mounting surface by placing #8 x 1 sheet metal screws in the screw guide holes (Figure A) from the start of the base (Figure B.) of the base every 4 inches. Begin by measuring 4" from the inside endcap screw that goes through the base and the endcap. 1 This screw measures 4" from the start of the base (Figure B.) DO NOT over tighten screws. DO NOT over tighten screws. Screw guideStep hole 3: Installing Bumper E Snap bumper onto base, either by using Figure A your hands or a rubber mallet. 4" NOTE: Cover mallet with a cloth so that you Step 2b: Installing the Base do not mar the bumper finish. Fix the base to the mounting surface by placing #8 x 1 sheet metal screws in the screw guide holes (Figure A) of the base every 4 inches. Adjust bumper so it is centered on the base. Screw guide hole Begin by measuring 4" from the inside endcap screw that goes through the base and the endcap. 1 This screw measures 4" from the start of the base (Figure B.) DO NOT over tighten screws. Figure A Step 2b: Installing the Base Fix the base to the mounting surface by placing #8 x 1 sheet metal screws in the screw guide holes (Figure A) 4" of the base every 4 inches. Begin by measuring 4" from the inside endcap screw that goes through the base and the endcap. 1 This screw measures 4" from the start of the base (Figure B.) Installing Bumper DO NOT over tighten screws. 6 Snap bumper onto base, either by using your hands or a rubber mallet. NOTE: Cover mallet with a cloth so that you do not mark the bumper finish. Adjust bumper so it is centered on the base. E 4" Step 3: Installing Bumper F Side View E Snap bumper onto base, either by using your hands or a rubber mallet. NOTE: Cover mallet with a cloth so that you do not mar the bumper finish. Adjust bumper so it is centered on the base. SECTION E-E SCALE 1 : 1 F SECTION F-F E SCALE 1 : 1 F Side View Streamline® Bumper | Page 3 of 3 SECTION E-E SCALE 1 : 1 F SECTION F-F SCALE 1 : 1.