User Manual EtherNet/IP and ControlNet to PROFIBUS PA Linking Devices Catalog Numbers 1788-EN2PAR, 1788-CN2PAR Important User Information Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards. Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams. No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited. Throughout this manual, when necessary, we use notes to make you aware of safety considerations. WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence. IMPORTANT Identifies information that is critical for successful application and understanding of the product. Labels may also be on or inside the equipment to provide specific precautions. SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present. BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous temperatures. ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE). Allen-Bradley, Rockwell Automation, ControlLogix, FactoryTalk, Studio 5000, Logix Designer, and RSNetWorx are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies Table of Contents Important User Information . 2 Preface Introduction. 7 About the Linking Devices . 7 Network Diagrams . 8 1788-EN2PAR Linking Device and EtherNet/IP Network . 8 1788-CN2PAR Linking Device and ControlNet Network . 9 Features . 9 General Precautions . 10 Prevent Electrostatic Discharge . 10 Environment and Enclosure. 11 European Hazardous Location Approval . 12 North American Hazardous Location Approval . 13 Additional Resources . 14 Chapter 1 Installation Hardware . 15 Power Connection . 15 PA Network Connections . 16 ControlNet and EtherNet/IP Connections. 18 Shielding . 18 PROFIBUS PA Physical Network Design Guidelines . 19 Power Supply . 19 Grounding/Earthing . 19 Cable Path. 20 Cable Lengths. 20 Cable Type and Minimum Requirements . 21 Cable Color Coding . 21 Termination Guidelines . 21 Set the Linking Device Network Address. 22 Hardware Switches Location . 22 Set the ControlNet Node Address . 22 Set the EtherNet/IP Address . 23 Ethernet Switch Settings . 24 ControlNet Switch Settings . 24 Software Installation . 25 AOP Version . 25 Firmware Revision. 25 Chapter 2 Set Up in the Studio 5000 Add the 1788-EN2PAR Linking Device to the I/O Tree . 27 Logix Designer Application Add the 1788-CN2PAR Linking Device to the I/O Tree. 28 Configure the Linking Device . 29 Configure the PA Master . 31 Configure the Field Devices. 32 Configure PV with Single Format. 32 Rockwell Automation Publication XXXX-X.X.X - Month Year 3 Table of Contents Configure PV with Multiple Formats . 33 Valve Positioner Configuration. 34 PROFIBUS PA Redundancy Setup . 36 Hardware . 36 Software . 39 MultiMaster Mode . 41 Redundant PA Code Example . 43 Chapter 3 Logix Assemblies PA Master Input Image . 45 Field Device Input Image . 46 Field Device Output Image. 48 Chapter 4 Diagnostics Linking Device is Offline. 49 Field Device is Not Detected . 50 Field Device is Not Configured. 52 Field Device Faults . 52 Web Interface. 54 Device Type Manager. 54 Appendix A Linking Device Display Status Main Page . 57 PA Master Page . 58 Field Device Page. 59 Appendix B PA Topology Master Mode 0 . 61 Master Mode 1 . 61 Master Mode 2 . 61 Master Mode 3 . 62 Master Mode 4 . 62 Master Mode 5 . 62 Master Mode 6 . 62 Master Mode 7 . 63 Master Mode 8 . 63 Master Mode 9 . 63 Master Mode 10. ..