101.77 GREENGUARD ® PRODUCT CERTIFIED FOR LOW CHEMICAL EMISSIONS HARMONY UL.COM/GG UL 2818 Interior Latex GOLD Semi-Gloss As of 08/01/2013, Complies with: OTC Yes LEED® 09 CI Yes B10-500 Series SCAQMD Yes LEED® 09 NC Yes CARB Yes LEED® 09 SC Yes CARB SCM 2007 Yes LEED® H Yes MPI # No NGBS Yes CHARACTERISTICS SPECIFICATIONS SURFACE PREPARATION Harmony Interior Latex provides a dura- Block WARNING! Removal of old paint by ble, low-odor, anti-microbial*, interior 1 ct. Loxon Block Surfacer* sanding, scraping or other means may paint formulated without silica. 2 cts. Harmony Interior Latex generate dust or fumes that contain lead. You can use this product, without typical Exposure to lead dust or fumes may odor complaints, in occupied areas be- Drywall cause brain damage or other adverse cause of the very low odor during applica- 1 ct. Harmony Interior Latex Primer health effects, especially in children or tion and drying. 2 cts. Harmony Interior Latex pregnant women. Controlling exposure to In addition, this product is specially for- lead or other hazardous substances re- mulated with odor-reducing properties to Masonry quires the use of proper protective equip- help reduce common household odors. ment, such as a properly fitted respirator 1 ct. Loxon Concrete & Masonry (NIOSH approved) and proper contain- Primer* Color: Most Colors ment and cleanup. For more information, To optimize hide and color development, always use or Harmony Interior Latex Primer call the National Lead Information Center the recommended P-Shade primer 2 cts. Harmony Interior Latex at 1-800-424-LEAD (in US) or contact Coverage: 350-400 sq ft/gal your local health authority. @ 4 mils wet; 1.6 mils dry Plaster Drying Time, @ 77°F, 50% RH: 1 ct. Premium Wall & Wood Primer* Remove all surface contamination by Touch: 1 hour or Harmony Interior Latex Primer washing with an appropriate cleaner, Recoat: 4 hours 2 cts. Harmony Interior Latex Drying and recoat times are temperature, humidity, rinse thoroughly and allow to dry. Existing and film thickness dependent peeled or checked paint should be Flash Point: N/A Wood, Composition Board scraped and sanded to a sound surface. Finish: 35 - 45 units @ 60° 1 ct. Premium Wall & Wood Primer* Glossy surfaces should be sanded dull. Tinting with CCE only: or Harmony Interior Latex Primer Stains from water, smoke, ink, pencil, Base oz/gal Strength 2 cts. Harmony Interior Latex grease, etc. should be sealed with the Extra White 0-5 125% appropriate primer/sealer. Deep Base 4-12 125% * These primers contain relatively low Vehicle Type: Styrenated Acrylic/EVA amounts of VOCs, but could result in Drywall B10W00551 minor, noticeable odors. Fill cracks and holes with patching paste/ VOC (EPA Method 24): spackle and sand smooth. Joint com- <50 g/L; 0.42 lb/gal Other primers may be appropriate. pounds must be cured and sanded As per 40 CFR 59.406 and SOR/2009-264, s.12 smooth. Remove all sanding dust. Volume Solids: 45 ± 2% When repainting involves a drastic color Weight Solids: 56 ± 2% change, a coat of primer will improve the Masonry, Concrete, Cement, Block Weight per Gallon: 10.5 lb hiding performance of the topcoat color. All new surfaces must be cured according to the supplier’s recommendations— * Anti-microbial usually about 30 days. Remove all form This product contains agents which inhibit release and curing agents. Rough sur- the growth of microbes on the surface of faces can be filled to provide a smooth this paint film. surface. If painting cannot wait 30 days, allow the surface to cure 7 days and prime the surface with Loxon Concrete & Masonry Primer. 7/2013 www.sherwin-williams.com continued on back 101.77 ® HARMONY Interior Latex Semi-Gloss B10-500 Series SURFACE PREPARATION APPLICATION CAUTIONS Plaster Apply at temperatures above 50°F. For interior use only. Bare plaster must be cured and hard. No reduction necessary. Protect from freezing. Textured, soft, porous, or powdery plaster Brush—Use a nylon/polyester brush. Non-photochemically reactive. should be treated with a solution of 1 pint Roller—Use a 3/8" - 3/4" nap synthetic household vinegar to 1 gallon of water. roller cover. CAUTIONS Use only with adequate ventilation. To avoid overex- Repeat until the surface is hard, rinse Spray—Airless posure, open windows and doors or use other means with clear water and allow to dry. Pressure ................................ 2000 psi to ensure fresh air entry during application and dry- Tip .................................... .013"-.017" ing. If you experience eye watering, headaches, or Wood dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid Sand any exposed wood to a fresh sur- CLEANUP INFORMATION contact with eyes and skin. Wash hands after using. face. Patch all holes and imperfections Keep container closed when not in use. Do not trans- with a wood filler or putty and sand fer contents to other containers for storage. FIRST Clean spills, spatters, hands and tools AID: In case of eye contact, flush thoroughly with smooth. immediately after use with soap and large amounts of water. Get medical attention if irrita- warm water. After cleaning, flush spray tion persists. If swallowed, call Poison Control Center, Mildew equipment with mineral spirits to prevent hospital emergency room, or physician immediately. Remove before painting by washing with WARNING: This product contains chemicals known rusting of the equipment. Follow manu- to the State of California to cause cancer and birth a solution of 1 part liquid bleach and 3 facturer’s safety recommendations when defects or other reproductive harm. DO NOT TAKE parts water. Apply the solution and scrub using mineral spirits. INTERNALLY. KEEP OUT OF THE REACH OF the mildewed area. Allow the solution to CHILDREN. remain on the surface for 10 minutes. HOTW 03/25/2013 B10W00551 09 00 Rinse thoroughly with water and allow the surface to dry before painting. Wear pro- tective eyewear, waterproof gloves, and protective clothing. Quickly wash off any of the mixture that comes in contact with your skin. Do not add detergents or am- monia to the bleach/water solution. Caulking Gaps between walls, ceilings, crown moldings, and other interior trim can be filled with the appropriate caulk after priming the surface. The information and recommendations set forth in this Product Data Sheet are based upon tests con- ducted by or on behalf of The Sherwin-Williams Com- pany. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin-Williams representative to obtain the most recent Product Data Sheet. .