5in. x 6in. Metal-Cutting Band Saw with Swivel Head

OWNER’S MANUAL

WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.

Item# 155792

Thank you very much for choosing a NORTHERN TOOL + EQUIPMENT CO., INC. Product! For future reference, please complete the owner’s record below: Model: ______Purchase Date: ______Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it.

This machine is designed for certain applications only. Northern Tool + Equipment cannot be responsible for issues arising from modification. We strongly recommend this machine is not modified and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted Northern Tool + Equipment to determine if it can or should be performed on the product.

For technical questions please call 1-800-222-5381. TECHNICAL SPECIFICATIONS

Motor 1/3 HP, 110V/220V, 60Hz, 1720 RPM Blade size 64-1/2" x 1/2" x .025" Blade speed 80, 120, 200 FMP

Angular Cut Maximum Capacity Circular 5" 0° Rectangular 5" x 6" Circular 3-3/4" 45° Rectangular 2-15/16" x 3-3/4" Circular 1-3/4" 60° Rectangular 1-3/4" x 2-3/16" FEATURES

1. Special designed horizontal and vertical band saw. 2. Offers three speeds for cutting metal plastic or wood. 3. Shuts off automatically when material is cut. 4. Scale for the mitering vise. 5. Low noise while operating. 6. Casters (optional) allow for quick and easy mobility. 7. Quick-positioning vise provides easy clamping on workpiece. 8. Built-in shelf for storing tools. GENERAL SAFETY RULES

WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood

Page 2 of 16 by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

WORK AREA

å Keep work area clean, free of clutter and well lit. Cluttered and dark work areas can cause accidents.

å Do not use your band saw where there is a risk of causing a fire or an explosion; e.g. in the presence of flammable liquids, gasses, or dust. Power tools create sparks, which may ignite the dust or fumes.

å Keep children and bystanders away while operating a band saw. Distractions can cause you to lose control, so visitors should remain at a safe distance from the work area.

å Be alert of your surroundings. Using band saws in confined work areas may put you dangerously close to cutting tools and rotating parts.

ELECTRICAL SAFETY

å WARNING! Always check to ensure the power supply corresponds to the voltage on the rating plate.

å Do not abuse the cord. Never pull tool cords from the receptacle. Keep power cords away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords may cause a fire and increase the risk of electric shock.

å Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. This unit is equipped with a 3-prong (grounded) plug for your protection against shock hazards and should be plugged directly into a properly grounded 3-prong receptacle. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.

å Extension Cord Use. A. Use only ‘Listed’ extension cords. If used outdoors, they must be marked “For Outdoor Use.” Those cords having 3-prong grounding type plugs and mating receptacles are to be used with grounded tools. B. Replace damaged or worn cords immediately. C. Check the name plate rating of your tool. Use of improper size or gauge of extension cord may cause unsafe or inefficient operation of your tool. Be sure your extension cord is rated to allow sufficient current flow to the motor. For the proper wire gauge for your tool, see chart.

Page 3 of 16

CHART FOR MINIMUM WIRE SIZE OF EXTENSION CORD: Nameplate AMPS CORD LENGTH 25' 50' 100' 150' 0-6 18 AWG 16 AWG 16 AWG 14 AWG 6-10 18 AWG 16 AWG 14 AWG 12 AWG 10-12 16 AWG 16 AWG 14 AWG 12 AWG 12-16 14 AWG 12 AWG (NOT RECOMMENDED) If in doubt, use larger cord. Be sure to check voltage requirements of the tool to your incoming power source.

å Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

å Do not let your fingers touch the terminals of plug when installing to or removing from the outlet.

å Ground fault circuit interrupters. If work area is not equipped with a permanently installed Ground Fault Circuit Interrupter outlet (GFCI), use a plug-in GFCI between power tool or extension cord and power receptacle.

å Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increase risk of electric shock if your body is grounded. PERSONAL SAFETY

å Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

å Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should be avoided.

å Use safety apparel and equipment. Use safety goggles or safety glasses with side shields which comply with current national standards, or when needed, a face shield. Use as dust mask in dusty work conditions. This applies to all persons in the work area. Also use non-skid safety shoes, hardhat, gloves, dust collection systems, and hearing protection when appropriate.

å Avoid accidental starting. Ensure the switch is in the off position before plugging tool into power outlet. In the event of a power failure, while a tool is being used, turn the switch off to prevent surprise starting when power is restored.

å Do not overreach. Keep proper footing and balance at all times.

å Be especially careful to keep fingers and hands out of path of blade when using band saw in a vertical position.

å Remove adjusting keys or wrenches before connecting to the power supply or turning on the tool. A wrench or key that is left attached to a rotating part of the tool may result in personal injury. TOOL USE AND CARE

å Do not force the tool. Band saws do a better and safer job when used in the manner for which they are designed. Plan your work, and use the correct tool for the job.

Page 4 of 16 å Never use a tool with a malfunctioning switch. Any band saw that cannot be controlled with the switch is dangerous and must be repaired by an authorized service representative before using.

å Disconnect power from band saw and place the switch in the locked or off position before servicing, adjusting, installing accessories or attachments, or storing. Such preventive safety measures reduce the risk of starting the power tool accidentally.

å Secure work with clamps or a vise instead of your hand to hold work when practical. This safety precaution allows for proper tool operation using both hands.

å Store idle band saw. When not in use, store the band saw in a dry, secure place out of the reach of children. Inspect tools for good working condition prior to storage and before re-use.

å Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool.

å Never stand on band saw. Serious injury could occur if the band saw is tipped or if the cutting blade is accidentally contacted.

å Keep guards in place and in working order.

å Before operating the band saw EACH TIME, check for alignment of moving parts; binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

å Never leave saw running unattended.

å When moving the saw, ALWAYS have the head lowered to the horizontal position. ASSEMBLY — Refer to PARTS LIST Part Number

A 1/3 or 1/2 HP motor split phase or capacitor start is recommended for best economical performance. Counterclockwise is required. Note that rotation can be reversed by following the directions given on the terminal or nameplate. 1. Assemble the motor mounting plate (#84) to the head (#81) using the long bolt (#98). Note that the flat side of the plate faces up. 2. Assemble the guard plate (#59) to the head using the screw (#83), lock washer (#8) and the carriage bolt (#12). Washer (#8) and wing nut are used to secure the motor mounting plate to the guard plate through the slotted hole in the guard plate. These components also serve to position and lock the motor in place or properly adjust belt speed. 3. Place the spacer over the long bolt and secure it with the nut. 4. Secure the motor (#85) to the motor mounting plate with the four bolts (#1) and nuts (#12). Note that the motor shaft (#85) is placed through the large opening in the guard plate and must be parallel with the drive shaft (#94). 5. Assemble the motor pulley (#86), the smaller of the two provided to the motor shaft (#85). Note the larger diameter must be closest to the motor. Do not tighten the set screw (#20). 6. Assemble the drive pulley (#86), the larger of the two provided, to the protruding drive shaft (#94). Note the smaller diameter must be closest to the bearing (#72). Do not tighten the set screw (#101-1). 7. Place the belt (#112) into one of the pulley grooves (#101) and the other end into the respective grooves of the second pulley. 8. Line up the belt and both pulleys such that the belt is running parallel in the pulley grooves. Page 5 of 16 9. Tighten the set screws of both pulleys in this position. 10. Place the belt into proper pulley combination for proper blade speed. See material cutting chart. 11. Adjust the position of the motor to obtain approximately 1/2" depression in the belt when applying pressure with your thumb. 12. Tighten the head screw (#83) holding the motor mounting plate to the guard plate. 13. Connect the electrical harness (#330) to the motor terminal box (#327). The motor should be protected with a circuit breaker with a rated amperage slightly greater than the full-load amperage of the motor.

WORK SETUP NOTE: Make sure the switch is in the OFF position and the saw is unplugged. 1. Raise the saw head (#81) to vertical position. 2. Open vise (#302) to accept the piece to be cut by rotating the wheel (#28) at the end of the base. 3. Place workpiece on saw bed. If the piece is long support the end. 4. Clamp workpiece securely in vise.

WORK STOP ADJUSTMENT NOTE: Make sure the switch is in the OFF position and the saw is unplugged. 1. Loosen the thumb screw (#302) holding the work stop casting to the shaft (#28). 2. Adjust the work stop casting to the desired length position. 3. Rotate the work stop to as close to the bottom of the cut as possible. 4. Tighten thumb screw. 5. Do not allow the blade (#113) to rest on the work while the motor is shut off.

BLADE SPEEDS When using your band saw always change the blade speed to best suit the material being cut. The material cutting chart gives suggested settings for several materials:

3- SPEED MATERIAL CUTTING CHART Speed FPM Belt Groove Used Material Motor Saw 60Hz pulley pulley Tool, stainless alloy steels, 24 Small Large bearing bronze Mild steel, hard brass or 36 Medium Medium bronze

Aluminum plastic 60 Large Small BLADE DIRECTION OF TRAVEL Be sure the blade is assembled to the pulleys so that the vertical edge engages the workpiece first.

Page 6 of 16 CAUTION: NEVER OPERATE SAW WITHOUT BLADE GUARDS IN PLACE. Be sure the blade is not in contact with the workpiece when the motor is started. First start the motor, allow the saw to come to full speed, then begin the cut by letting the head down slowly onto the work. DO NOT DROP OR FORCE THE SAW HEAD. Let the weight of the saw head provide the cutting force. The saw automatically shuts off the end of the cut.

BLADE SELECTION AN 8 TPI, general-use blade is furnished with this metal cutting band saw. Additional blades in 4-, 6-, 8- and 10-tooth sizes are available. The choice of the blade pitch is governed by the thickness of the work to be cut; the thinner the workpiece, the more teeth recommended. A minimum of three teeth should engage the workpiece at all times for proper cutting. If the teeth of the blade are so far apart that they straddle the work, severe damage to the workpiece and to the blade can result.

CHANGING BLADE NOTE: Make sure the switch is in the OFF position and the saw is unplugged. Raise saw head to vertical position and open the blade guards. Loosen tension screw knob (#79) sufficiently to allow the saw blade to slip off the wheels. Install the new blade with teeth slanting toward the motor as follows: 1. Place the blade in between each of the guide bearings. 2. Slip the blade around the motor pulley (bottom) with the left hand and hold in position. 3. Hold the blade taut against the motor pulley by pulling the blade upward with the right hand which is placed at the top of the blade. 4. Remove left hand from bottom pulley and place it at the top side of the blade to continue pulling upward on the blade. 5. Remove right hand from blade and adjust the position of the top pulley to permit left hand to slip the blade around the pulley. 6. Adjust the blade tension knob clockwise until it is tight enough so no blade slippage occurs. Do not over tighten. 7. Replace the blade guards. 8. Place 2-3 drops of oil on the blade.

BLADE GUIDE BEARING ADJUSTMENT

ATTENTION: This is the most important adjustment on your saw. It is impossible to get satisfactory work from your saw if the blade guides are not properly adjusted. The blade guide is depending on your metal. Cutting Band Saws are adjusted and power tested with several test cuts before leaving the factory to insure proper setting. The need for adjustment should rarely occur when the saw is used properly. If the guides do get out of adjustment, it is extremely important to readjust immediately. If proper adjustment is not maintained, the blade will not cut straight, and if the situation is not corrected it will cause serious blade damage. Because guide adjustment is a critical factor in the performance of your saw, it is always best to try a new blade to see if this will correct poor cutting before beginning to adjust. If a blade becomes dull on one side sooner than the other, for example, it will begin cutting crooked. A blade change will Page 7 of 16 correct this problem — the guide adjustment will not. If a new blade does not correct the problem, check the blade and guides for proper spacing. NOTE: There should be from 000 (just touching) to 001 clearance between the blade and guide bearings. To obtain this clearance adjust as follows: NOTE: Make sure the switch is in the OFF position and the saw is unplugged. 1. The inner guide bearing is fixed and cannot be adjusted. 2. The outer guide bearing is mounted to an eccentric bushing and can be adjusted. 3. Loosen the nut while holding the bolt with an Allen wrench. 4. Position the eccentric by turning the bolt to the desired position of clearance. 5. Tighten the nut. 6. Adjust the second blade guide bearing in the same manner.

ADJUSTING BLADE TENSION NOTE: Make sure the switch is in the OFF position and the saw is unplugged. 1. Press the blade lightly with left hand, aligning the rear blade against the flange of the blade wheel and test the blade tension. 2. Adjust the blade tension adjustable knob with the right hand until the blade obtains the proper tension.

ADJUSTING THE BLADE TRACKING This adjusting has been completed and tested at the factory. The need for adjustments should rarely occur when the saw is used properly. If the tracking goes out of adjustment, proper blade readjustment is listed below:

Step 1: Turn simultaneously with adjusting set screw to make the blade track against the shoulder of the pulley.

To increase blade tension To relieve blade tension Step 2: Loosen this S tep 5: Adjust blade adjustable hex-head screw before s eat according to the material turning the adjusting set s ize. scSretewp. 4: Tighten after adjusting The arrow indicates the moving direction Step 3: Turn simultaneously with blade tension knob to make Step 6: Adjust guide assembly to blade track against shoulder of where the blade just touches the pulley b ack-up bearing.

Page 8 of 16

CUTTING Close switch, letting the head down slowly onto the work. Do not drop or force. Let the weight of the saw head provide the cutting force. The saw automatically shuts off at end of the cut. Method of adjusting blade: A. Loosen the screw #11. B. Adjust the blade adjustable seat (#64) to make the blade vertical to bed. C. Place a square on the bed to check if the blade is vertical, if not, repeat the process A to C. D. Tighten the screw (#11).

TELL TALE CHIPS Chips are the best indicator of correct feed force. Monitor chip debris and adjust feed accordingly. If you see thin or powdered chips, increase feed rate or reduce band speed.

Burned heavy

Chips: Reduce feed rate and/or band speed.

Curly silvery and warm chips: Optimum feed rate and band speed.

MAINTENANCE

CAUTION: MAKE CERTAIN THE BAND SAW IS DISCONNECTED FROM THE POWER SOURCE BEFORE ATTEMTING TO SERVICE OR REMOVE ANY COMPONENT!

LUBRICATION Lubricate the following components using SAE-30 oil as noted. 1. Ball-bearing: None. 2. Driven pulley bearing: 6-8 drops a week. 3. Vise lead screw: As needed. 4. The drive gears run in an oil bath and will not require a lubricant change more often than once a year, unless the lubricant is accidentally contaminated or a leak occurs because of improper replacement of the gearbox cover. During the first few days of operation, the worm gear drive will run hot. Unless the temperature exceeds 200°F, there is no cause for concern. The following lubricants may be used for the gear box: 1. Atlantic Refinery Co., Mogul Cyl. Oil 2. Cities Service Optimus No.6 3. Gulf Refinery Co Medium Gear Oil 4. Pure Oil co. Park Clipper Page 9 of 16 TROUBLE SHOOTING CHART Symptom Possible Cause (s) Corrective Action 1. Material loose in vise 1. Clamp work securely 2. Incorrect speed or feed 2. Adjust speed or feed Excessive 3. Blade teeth spacing too large 3. Replace with a smaller teeth Blade 4. Material too coarse spacing blade Breakage 5. Incorrect blade tension 4. Use a blade of slow speed 6. Teeth in contact with and small teeth spacing material before saw is 5. Adjust so blade does started not slip on wheel 7. Blade rubs on wheel flange 6. Place blade correctly in 8. Misaligned guide bearings relation with workpiece 9. Cracking at weld 7. Adjust wheel alignment 8. Adjust guide bearings 9. Weld again 1. Teeth too coarse 1. Use finer teeth 2. Too much speed 2. Decrease speed Premature 3. Inadequate feed pressure 3. Decrease spring tension on Blade 4. Hard spots or scale on side of saw Dulling material 4. Reduce speed, increase feed 5. Work hardening of material pressure 6. Blade twist 5. Increase feed pressure by 7. Insufficient blade reducing spring tension 6. Replace with a new blade and adjust blade tension 7. Tighten blade tension adjusting knob Unusual 1. Blade guides worn 1. Replace Wear on 2. Blade guide bearings not 2. Adjust as per operator’s Side/Back of adjusted properly manual Blade 3. Blade guide bearing bracket 3. Tighten is loose

1. Tooth too coarse for work 1. Use finer tooth blade 2. Too heavy pressure, too slow 2. Decrease pressure, increase Teeth speed speed Ripping from 3. Vibrating workpiece 3. Clamp workpiece securely Blade 4. Gullets loading 4. Use coarse tooth blade or brush to remove chips 1. Blade tension too high 1. Reduce tension on blade 2. Drive belt tension too high 2. Reduce tension on drive belt Motor 3. Gears need lubrication 3. Check oil bath running too 4. Cut is binding blade 4. Decrease feed and speed hot 5. Gears aligned improperly 5. Adjust gears so that worm is in center of gear

Page 1 0o f 16 1. Feed pressure too great 1. Reduce pressure by Bad Cuts 2. Guide bearing not adjusted increasing spring tension on properly side of saw 3. Inadequate blade tension 2. Adjust guide bearing, the 4. Dull blade clearance can not be greater 5. Speed incorrect than 0.2mm. 6. Blade guide spaced out too 3. Increase blade tension by much adjust blade tension 7. Blade guide assembly loose 4. Replace blade 8. Blade truck too far away from 5. Adjust speed wheel flanges 6. Adjust guides space 7. Tighten 8. Re-track blade according to operating instructions Bad Cuts 1. Too much speed or feed 1. Decrease speed or feed (Rough) 2. Blade is too coarse 2. Replace with finer blade 3. Blade tension loose 3. Adjust blade tension Blade is 1. Cut is binding blade 1. Decrease feed pressure twisting 2. Too much blade tension 2. Decrease blade tension

Page 1 1o f 16 PARTS LIST

Part Description Qty. Part Description Qty. No. No.

1 Hex. Head screw 4 84 Motor mount plate 1 2 Hex. nut 1 85 Motor 1 3 Spring washer 3 86 Motor pulley 1 8 Washer 8 89 Oil seal 1 9 Wheel (option) 2 90 Worm gear assembly 1 11 Hex. Head screw 2 92 Gear box gasket 1 12 Hex. nut 4 93 Gear box cover 1 16 Motor cable 1 94 Worm gear shaft assembly 1 17 Pivoting rod 1 98 Plum screw 1 19 Distance set bracket 1 100 Flat cross head screw 18 20 Hex. Socket headless screw 2 101 Worm gear pulley 1 21 Stock stop rod 1 101-1 Headless hexagon socket 1 28 Hand wheel assembly 1 screw 1 31 Hex. Head screw 1 102 Spring washer 1 35 Flat washer 2 103 Blade tension sliding plate 1 44 Power cable 1 104 Headless hexagon socket 48 Cross round head screw 4 screw 2 50 Hex. Head screw 3 108 Shaft block 1 51 Washer 3 109 Blade tension sliding guide 2 54 Pivot 1 110 Motor pulley cover 1 55 Vertical saw table 1 110-1 Motor pulley cover 1 56 Table supporting plate 111 Motor pulley cover assy. 1 57 Adjustable bracket (left) 1 112 Belt 1 58 Plum screw 1 113 Blade 1 59 Blade back safety cover 4 117 Spring washer 4 59 Blade back safety cover 1 120 Bushing 1 63 Blade adjustable assembly 123 Hex. Head screw 1 (rear) 1 124 Fixed plate 1 64 Blade adjustable assembly 125 Hex. Head screw 1 (front) 1 126 Hex. Head screw 1 65 Adjustable bracket (right) 1 132 Safety guard (right) 1 66 Lock knob 1 132-1 Safety guard (left) 1 68 Flat cross head screw 1 182 Washer 2 71 Blade wheel assembly (front) 1 183 Hex. Nut 1 72 Bearing cover 1 194 Washer 1 74 Key 1 196 Hex. Head screw 1 75 Hex. Head screw 10 197 Hex. Head screw 1 76 Switch cut off tip 1 198 C-retaining ring 1 77 Blade wheel assembly (rear) 1 199 Hex. Head screw 1 78 Blade wheel assembly (rear) 1 200 Hex. Head screw 1 79 Blade tension adjustable 201 Hex. Nut 1 knob 1 202 Hex. Nut 1 80 Spring 1 254 Support rod 1 81 Body fame 1 255 Headless hex. Screw 1 83 Hex. Head screw 2 256 Spring washer 1 257 Hex. Head screw 1 341 Hex. Nut 6 258 Cylinder assembly 1 342 Balancing bracket 1 259 Cylinder upper support 1 343 Flat washer 2 261 Hex. Socket headless screw 1 344 Hexagon head screw 2 262 Hex. Head screw 2 345 Flat briquette 1 263 Spring washer 2 346 Screw rod 1

Page 1 2o f 16 300 Hex. Socket head screw 1 347 Balancing spring 1 301 Vise jaw bracket (rear) 1 348 Leg 4 302 Vise jaw bracket (front) 1 349 Built-in shelf (option) 1 303 Wall plate 1 350 Front plate 1 304 Swivel base (upper) 1 351 Hex. Head screw 14 305 Bracket 1 352 Flat screw 14 306 Acme nut 1 353 Hex. Nut 14 307 Acme screw 1 354 Hex. Nut 4 308 Bushing 2 355 Flat washer 4 309 Flat washer 2 356 Hexagon head screw 4 310 Hexagon screw 2 357 Walking wheel set 2 311 Hex. Head screw 3 359 Stand complete assy. 1 312 Flat screw 5 360 Wheel setting bracket 2 313 Hexagon screw 2 361 Wheel rod 1 314 Hex. Socket headless screw 2 362 Hex. Head screw 4 315 Positioning ring 1 363 Spring washer 8 316 Hex. Nut 1 364 Hex. Nut 4 317 Flat washer 1 365 Hex. Head screw 4 318 Hexagon screw 1 366 Rubber head screw 4 319 Hex. Nut 1 367 Spring washer 16 320 Hex. Head screw 1 368 Cross round head screw 16 321 Position pin 1 369 Knob w/shaft 1 322 Plum handle 1 370 Knob 1 323 Screw 2 371 Cotter pin 1 324 Handle 1 372 Handle shaft stopper 1 325 Carriage screw 1 373 Screw plate 1 326 Screw 1 374 Pivot pin 1 327 Electrical box 1 375 Ball 1 328 Switch base 1 376 Ring 1 329 Cross round head screw 2 377 Cross round head screw 2 330 On-off switch 1 378 Chain 1 331 Screw 2 332 Cable connector 2 333 Cotter pin 2 334 Protect plate 1 338 Scale 1 339 Hex. Head screw 6 340 Flat washer 6

For replacement parts and technical questions, please call 1-800-222-5381.

Page 1 3o f 16 DIAGRAM

Page 1 4o f 16

Page 1 5o f 16

WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints, • Crystalline silica from bricks and cement and other masonry products, and • Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of w ork. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Northern Tool + Equipment Co., 2800 Southcross Drive West P.O. Box 1499 Burnsville, MN 55337-0499 Made in China

Page 1 6o f 16