TRANSMISSION TEST SET 806A TIMS

CLEI NUMBER: TETN76A1AA

CLEI NUMBER: TETYAEWUAA

MULTI-SERVICE TIMS (Transmission Impairment Measuring CONTROLS Front panel controls are simple and utilize large Set). The 806A supports a wide range of services including: bright LED displays and indicators which are grouped for ease POTS, DATA, Program, DDS, DSL (ISDN basic rate), and T1 of use. The 806A comes with software that runs under DOS or via HDSL. It measures: LEVEL, DELAY, FREQUENCY, Windows. The PC communicates with the test set through an , NOISE with TONE, S/N RATIO, NOISE to GROUND, RS-232 Port which is located on the side or rear of the test set. IMPULSE NOISE, IMPULSE NOISE with TONE, and IMPULSE NOISE to GROUND per IEEE Standard 743- 1995.The 806A is easy to operate from the front panel (or from a personal computer) and it has AUTO-TEST capability for VF, DSL and HDSL facilities. It is also accurate, rugged and economical STRAIGHTAWAY DELAY Expanded use of 2 Wire transmission (FAX, Modem, ISDN DSL, and HDSL) has accentuated the need for a 2 Wire, STRAIGHTAWAY Envelope Delay Distortion (EDD) Measurement. The 806A introduces a new, Patented EDD Technique which: handles VF, DSL, and HDSL Frequencies; measures on a 2 wire basis; is comparable to, and compatible with the Standard 4 Wire EDD Measurement. Extended Round Trip Delay was added to facicilitate alignment of delay lines in Simulcast Radio Systems. NOISE is measured with one of eight weighting filters. Noise- to-ground (or Power Influence) is measured directly using standard test leads. A 1010 Hz Notch Filter is provided to measure NOISE-with-TONE, Signal to Noise Ratio, or Signal to Total Distortion Ratio. FILTER APPLICATION C MSG POTS Voice Traffic D filter POTS modem or fax POTS power line / ringing interference 3.4 kHz The Portable 806A includes: a rechargeable battery, padded 15 kHz POTS Level, Delay, EDD / Program Noise field case, two miniature phone plug / clip test leads, an RS- 1010 Notch POTS S/N Ratio / Noise, S/N on PCM 232 PC Cable, PC Software, Operating Manual, and an AC E Filter ISDN (DSL) Level and Noise / DDS Power Cord.The battery powers the test set for 8 hours. HDSL Level and Noise, S/N Ratio F Filter The Rack Mounted 806AR has the I/O brought out on jacks 200 kHz ISDN (DSL) and DDS Attn Dist, EDD on the front panel and spade lugs on the rear panel. 115 VAC 500 kHz HDSL Level, Attenuation Distortion, EDD Power standard. 230 VAC, -24 or -48 VDC options available.

© 2003 CONVEX CORP SPECIFICATIONS 806A TIMS / 806AR TIMS LEVEL EXTENDED ROUND TRIP DELAY Dynamic Range Dynamic Ranges 0 to 1,000,000 uSec, 0 to 3,000,000 uSec -80 to +24 dBm 15 kHz, 200 kHz-600/900 Resolution 1 uSec -70 to +24 dBm 200 kHz, 500 kHz Accuracy ?5 uSec -20 to +20 dB TLP offset ENVELOPE DELAY Freq. Range 20 Hz to 300 kHz Dynamic Range -3000 to +9000 uSec Resolution 0.1 dB Frequency Range200 Hz to 300 kHz Detector Average or RMS, Selectable RCV Level -40 to +20 dBm Accuracy SEND Level -40 to +7 dBm +24 dBm ?0.5 dB ?0.2 dB ?0.5 dB ?1 dB Modulation 50% AM, 83 1/3 Hz -40 dBm ?0.5 dB ?0.5 dB ?1.0 dB ?2 dB Resolution 1 uSec -80 dBm Accuracy ?10 uSec 20Hz 200Hz 15kHz 200kHz Operating Modes 2W Straightaway - Patented 22 tone , 300kHz Local, Forward / Return Reference 1002 to 1022 Hz / 0 to -19 dBm: ?0.1 dB Remodulation Forward / Return Reference Filters Hum Reject, IN/OUT High Pass, -60 dB at 60 Hz 15 kHz Flat, VF Low Pass, -3 dB at 15 kHz GENERATOR 200 kHz, Wide Band Low Pass, -3 dB at 200 kHz Dynamic Range -41 to +10 dBm 500 kHz, Extra WB Low Pass, -3 dB at 500 kHz Resolution 0.1 dB Steps Accuracy ?0.1 dB -19 to 0 dBm, ±0.2 dB -1 kHz FREQUENCY Freq. Range 20 to 300 kHz Count Range 20 Hz to 300 kHz Resolution 1 Hz - to 4 kHz, 10 Hz - to 30 kHz, Level Range -50 to +24 dBm - 15 kHz Bandwidth 100 Hz - to 300 kHz -40 to +24 dBm - 200 kHz Bandwidth Accuracy 1 Hz to 10 kHz, 30 Hz to 300 kHz, -30 to +24 dBm - 500 kHz Bandwidth Flatness 0.2 dB to 15 kHz, 1 dB to 300 kHz Resolution 1 Hz to 30 kHz, 10 Hz to 300 kHz TH Distortion -50 dB - 1004 Hz, -40 dB - 20 Hz to 300 kHz Accuracy 1 Hz to 30 kHz, 10 Hz to 300 kHz ? ? Quick Freq's 4 Programmable Frequency Keys NOISE, NOISE w TONE Auto Sweep:VF, DSL, HDSL / 500 kHz Dynamic Range 10 to 114 dBrn or -80 to +24 dBm for INPUT / OUTPUT PORTS C MSG, 3.4 kHz, D, E, 15 kHz Filters Quantity 2 Measure / Dial Ports - Portable: A/C, B/D 20 to 114 dBrn or -70 to +24 dBm for Rack Mount: A, B Ports on front and rear 200 kHz, F, 500 kHz Filters Operation 2 Wire, 4 Wire Holding Tone -40 to +10 dBm / 995 to 1025 Hz Impedance 100, 135, 600, 900 Ohms Resolution 0.1 dB Independent RCV / SEND Selection Detector RMS 135, 600, 900 30 dB / 100 15 dB Accuracy ?1 dB Receive Bridge Less than .2 dB S/N RATIO (S/TD RATIO, signal to total distortion) Hold Dual, 23 ma Nominal Dynamic Range 10 to 50 dB (excludes E and F Filters) GENERAL Holding Tone -40 to +10 dBm / 995 to 1025 Hz MONITOR Speaker with Volume Control Resolution 0.1 dB DIAL Parallel Bantam Jacks for Dial / Talk Accuracy ?1 dB TEMP Operate +0 to +50 C / Store -40 to +71 C NOISE to GROUND (Power Influence) PC CONTROL Serial Port: RS-232 / 9 pin D Connector, Dynamic Range POWER 115 VAC +/-10%, Option: 100 or 230 VAC 30 to 140 dBrn, or -60 to +50 dBm 806 Battery Run: 8 Hrs. / Recharge: 8 Hrs. 40 to 140 dBrn, -50 to +50 dBm -F / 500 kHz PORTABLE 9.0 x 11.0 x 3.5 Inches Resolution 0.1 dB 229 x 279 x 89 mm Accuracy ?1 dB WEIGHT 9.0 lbs. / 4.1 kg. including Battery

3-LEVEL IMPULSE NOISE, IMPULSE NOISE w TONE RACK MOUNT 7.5 x 19.0 x 1.7 Inches Dynamic Range 30 to 115 dBrn - C, D, 3.4, 15 kHz Filters 191 x 483 x 43 mm 40 to 115 dBrn - 200 kHz, E, F Filters WEIGHT 5.0 lbs. / 2.3 kg. 50 to 115 dBrn - 500 kHz Filter Impulse w Tone excludes E and F Filters WARRANTY All Convex products are warranted to be free of manufacturing Thresholds 3 /LOW, MID (+4 dB), HI (+8 dB) defects for a period of one year from the date of shipment. No other warranties are expressed or implied. Convex Corporation Accuracy ? 1 dB is not liable for consequential damages. Count Capacity 32,000 Count Rate 8, 100 Counts/Second PRODUCT REPAIR SERVICE Holding Tone -40 to +10 dBm / 1002 to 1022 Hz Post warranty repair service is available for Convex products. Loss of TONE Measurement halted, auto resume Where there is no observable mechanical damage, the Model 806A or 806AR will be repaired and/or recalibrated for a fixed TRANSIENT TIMER fee. Otherwise, Convex will advise as to the nature and cost of Timer Set 1 Minute Steps up to 8 Hours repair and, subject to customer instructions, will promptly Resolution 1 Second repair and return the product. Accuracy ? 1 Second Convex Corporation - 1319 Shepard Drive - Sterling, VA 20164 USA 703-433-9901 - fax 703-433-9904 - www.ConvexCorp.com