1 NEC Group internal useonly

静電 25SG017 配布先 ITPF-P13-00172 NECST・プラットフォ-ム(事)・第一技術 G Satsuma2-STD 2013.12.13 高瀬 M 殿、佐川 S 殿 ITPF・第ニ開発統括 G (Hoju-C 搭載) 細谷殿、渡辺殿 承認 査閲 担当

静電気耐力試験結果報告書 村木 新井 Cc: 渡 M 殿, 村木 S 殿

表題の装置の環境試験を実施致しましたので、結果を下記に報告致します。

- 記 -

1.試験日 平成25年08月26~27日(2日間)

2.試験者 NECST・SP(事)・1技-G 渡辺殿 ITPF 第二開発統括 G 新井

3.試験場所 府中(事) 8号館1階 環境評価試験室

4.試験サンプル数 1台

5.試験結果及び放電箇所 (詳細は、表-1、図-1参照のこと。)

判定:合格 6.試験装置構成

機器概要 装置名:Satsuma2-STD(Hoju-C 搭載) 定格電圧値:200-240V 定格電流値:30A: 4P/S <装置ブロック図>

<Hoju-B> CPU-Blad SWM <Satsuma2 - STD> slot# slot#1 <10GbE-SW(L3)> 250GB SATA x 2 内 1 slot#2 <10GbE-SW(L3)> <Satsuma2 - STD> slot# slot#3 <10GbE-SW(L3)> 300GB SAS x 2 内蔵 2 slot#4 <10GbE-SW(L3)> <Satsuma2 - STD> slot# slot#5 <10GbE-SW(L3)> 250GB SATA x 2 内 3 slot#6 <10GbE-SW(L3)> <Satsuma2 - STD> slot# 100GB SSD x 2 内蔵 4 キーボード <Satsuma2 - STD> slot# マウス Disk Less Cage 5 <Satsuma2 - STD> slot# モニター PSU 300GB SAS x 2 内蔵 6 slot#1 <Satsuma2 - STD> slot# <80PLUS PSU> Disk Less Cage 7 slot#2 <80PLUS PSU> <Satsuma2 - STD> slot# slot#3 <80PLUS PSU> 100GB SSD x 2 内蔵 8 slot#4 <80PLUS PSU> 2 NEC Group internal useonly

環境試験実施装置構成 slot Nコード LAN ライ Mezzanine 装置 増設 CPU DIMM DiskCage TPM XB 組込Kit No (代表) ザ Type1 Type2 Satsuma2 - 1 N8400-221Y N8401-078 接続対象混載 N8403-059 N8403-061 2ch NIC 4ch NIC N8415-002 N8415-003 STD Satsuma2 - 2 N8400-222Y N8401-079 接続対象混載 N8403-059 N8403-062 2ch NIC 4ch NIC N8415-002 N8415-003 STD Satsuma2 - 3 N8400-223Y N8401-080 接続対象混載 N8403-057 N8403-064 2ch NIC 4ch NIC N8415-002 N8415-003 STD Satsuma2 - 4 N8400-224Y N8401-081 接続対象混載 N8403-057 N8403-061 2ch NIC 4ch NIC N8415-002 N8415-003 STD Satsuma2 - 5 N8400-225Y N8401-082 接続対象混載 N8403-056 N8403-062 2ch NIC 4ch NIC N8415-002 N8415-003 STD Satsuma2 - 6 N8400-221Y N8401-078 接続対象混載 N8403-059 N8403-064 2ch NIC 4ch NIC N8415-002 N8415-003 STD Satsuma2 - 7 N8400-221Y N8401-078 接続対象混載 N8403-056 N8403-061 2ch NIC 4ch NIC N8415-002 N8415-003 STD Satsuma2 - 8 N8400-221Y N8401-078 接続対象混載 N8403-059 N8403-062 2ch NIC 4ch NIC N8415-002 N8415-003 STD

3 NEC Group internal useonly

<装置銘板図>

7.実行T&D NECST・SP(事)・1WAS-G指定の TeDoLi を実施

・ Keyboard - Key Operation Check Test

・ Mouse - Cursor/Button Operation Check Test

・ Serial - Loopback Test

・ VRAM - VRAM Read/Write Test

・ Memory - Block Move Test - Address Test

・ Cache - Stuck Addresss Test - Compare XOR/SUB/MUL/DIV/OR/AND Test

・ USB Device (DVD Drive) - Random Read Test

・ USB Device (USB-DOM) - Random Read Test

・ HDD or SSD - Random Read/Write Test

・ Network (Onboard ch1/2) - Loopback Test

・ Network (1G NIC Mezz(2ch)) - Loopback Test

・ Network (1G NIC Mezz(4ch)) - Loopback Test

8.関連基準類 サーバ(事)設置環境・安全に関する基準とその評価試験手順 CASDL-92026(9版)

4 NEC Group internal useonly

静電耐力試験実施の写真

5 NEC Group internal useonly

静電気耐力試験 表-1-1/5

装置名: Satsuma2-STD(Hoju-C搭載) 試験日: 2013.08.26~27 試験場所: #8-1 環境評価試験室 試験担当者: 渡辺殿 試験電圧: 200 V~ V 周波数: 50 Hz 温度: 23 ℃ 湿度 50 % 装置№: - 製造年月: -

放 出力電圧 (KV) 備考欄 電 気中放電 物理的 箇 接触放電 許容 所 3 4 5 6 10 2 4 6 8 10 10 極性 + - + - + - + - + - + - + - + - + - + - + - 1 ○ ○ ○ ○ 1スロット 1 ○ ○ ○ ○ 2スロット 1 ○ ○ ○ ○ 3スロット 1 ○ ○ ○ ○ 4スロット 1 ○ ○ ○ ○ 5スロット 1 ○ ○ ○ ○ 6スロット 1 ○ ○ ○ ○ 7スロット 1 ○ ○ ○ ○ 8スロット 2 ○ ○ ○ ○ 1スロット 2 ○ ○ ○ ○ 2スロット 2 ○ ○ ○ ○ 3スロット 2 ○ ○ ○ ○ 4スロット 2 ○ ○ ○ ○ 5スロット 2 ○ ○ ○ ○ 6スロット 2 ○ ○ ○ ○ 7スロット 2 ○ ○ ○ ○ 8スロット 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2スロット 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3スロット 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4スロット 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5スロット 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6スロット 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 7スロット 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8スロット 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2スロット 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3スロット 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4スロット 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5スロット 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6スロット 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 7スロット 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8スロット 5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2スロット 5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3スロット 5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4スロット 5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5スロット 5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6スロット 5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 7スロット 5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8スロット 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2スロット 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3スロット 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4スロット 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5スロット 6 NEC Group internal useonly

静電気耐力試験 表-1-2/5

放 出力電圧 (KV) 備考欄 電 気中放電 物理的 箇 接触放電 許容 所 3 4 5 6 10 2 4 6 8 10 10 極性 + - + - + - + - + - + - + - + - + - + - + - 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6スロット 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 7スロット 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8スロット 7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2スロット 7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3スロット 7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4スロット 7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5スロット 7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6スロット 7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 7スロット 7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8スロット 8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2スロット 8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3スロット 8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4スロット 8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5スロット 8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6スロット 8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 7スロット 8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8スロット 9 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 9 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2スロット 9 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3スロット 9 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4スロット 9 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5スロット 9 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6スロット 9 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 7スロット 9 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8スロット 10 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 10 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2スロット 10 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3スロット 10 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4スロット 10 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5スロット 10 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6スロット 10 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 7スロット 10 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8スロット 11 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 11 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2スロット 11 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3スロット 11 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4スロット 11 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5スロット 11 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6スロット 11 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 7スロット 11 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8スロット 12 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 12 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2スロット 12 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3スロット 12 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4スロット 12 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6スロット 12 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 8スロット 13 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1スロット 7 NEC Group internal useonly

静電気耐力試験 表-1-3/5

放 出力電圧 (KV) 備考欄 電 気中放電 物理的 箇 接触放電 許容 所 3 4 5 6 10 2 4 6 8 10 10 極性 + - + - + - + - + - + - + - + - + - + - + -

14 ○ ○ ○ ○ 左

14 ○ ○ ○ ○ 右

15 ○ ○ ○ ○ 左 15 ○ ○ ○ ○ 右 16 ○ ○ ○ ○ 1P/S 16 ○ ○ ○ ○ 2P/S 16 ○ ○ ○ ○ 3P/S 16 ○ ○ ○ ○ 4P/S 17 ○ ○ ○ ○ 18 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 19 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

20 ○ ○ ○ ○ 21 ○ ○ ○ ○ 22 ○ ○ ○ ○ 左 22 ○ ○ ○ ○ 右 23 ○ ○ ○ ○ 1FAN-BOX 23 ○ ○ ○ ○ 2FAN-BOX 23 ○ ○ ○ ○ 3FAN-BOX 23 ○ ○ ○ ○ 4FAN-BOX 23 ○ ○ ○ ○ 5FAN-BOX 24 ○ ○ ○ ○ 1FAN-BOX

24 ○ ○ ○ ○ 2FAN-BOX 24 ○ ○ ○ ○ 3FAN-BOX 24 ○ ○ ○ ○ 4FAN-BOX 24 ○ ○ ○ ○ 5FAN-BOX 25 ○ ○ ○ ○ 1スロット 25 ○ ○ ○ ○ 2スロット 25 ○ ○ ○ ○ 3スロット 25 ○ ○ ○ ○ 4スロット 25 ○ ○ ○ ○ 5スロット 25 ○ ○ ○ ○ 6スロット

26 ○ ○ ○ ○ 1スロット 26 ○ ○ ○ ○ 2スロット 26 ○ ○ ○ ○ 3スロット 26 ○ ○ ○ ○ 4スロット 26 ○ ○ ○ ○ 5スロット 26 ○ ○ ○ ○ 6スロット 27 ○ ○ ○ ○ 1スロット 27 ○ ○ ○ ○ 2スロット 27 ○ ○ ○ ○ 3スロット

27 ○ ○ ○ ○ 4スロット

27 ○ ○ ○ ○ 5スロット 27 ○ ○ ○ ○ 6スロット

8 NEC Group internal useonly

静電気耐力試験 表-1-4/5

放 出力電圧 (KV) 備考欄 電 気中放電 物理的 箇 接触放電 許容 所 3 4 5 6 10 2 4 6 8 10 10 極性 + - + - + - + - + - + - + - + - + - + - + - 28 ○ ○ ○ ○ 1スロット 28 ○ ○ ○ ○ 2スロット 28 ○ ○ ○ ○ 3スロット 28 ○ ○ ○ ○ 4スロット 28 ○ ○ ○ ○ 5スロット 28 ○ ○ ○ ○ 6スロット 29 ○ ○ ○ ○ 1スロット 29 ○ ○ ○ ○ 2スロット 29 ○ ○ ○ ○ 3スロット 29 ○ ○ ○ ○ 4スロット 29 ○ ○ ○ ○ 5スロット 29 ○ ○ ○ ○ 6スロット 30 ○ ○ ○ ○ 1スロット 30 ○ ○ ○ ○ 2スロット 30 ○ ○ ○ ○ 3スロット 30 ○ ○ ○ ○ 4スロット 30 ○ ○ ○ ○ 5スロット 30 ○ ○ ○ ○ 6スロット 31 ○ ○ ○ ○ 左 31 ○ ○ ○ ○ 右 32 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1P/S 32 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2P/S 32 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 3P/S 32 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 4P/S 33 ○ ○ ○ ○ 1P/S 33 ○ ○ ○ ○ 2P/S 33 ○ ○ ○ ○ 3P/S 33 ○ ○ ○ ○ 4P/S 34 ○ ○ ○ ○ 左 34 ○ ○ ○ ○ 右 35 ○ ○ ○ ○ 左側 36 ○ ○ ○ ○ 右側 37 ○ ○ ○ ○ 左 37 ○ ○ ○ ○ 右 38 ○ ○ ○ ○ 39 ○ ○ ○ ○ 40 ○ ○ ○ ○ 9 NEC Group internal useonly

静電気耐力試験 表-1-5/5

放 出力電圧 (KV) 備考欄 電 水平結合板 垂直結合板 物理的 箇 接触放電 気中放電 許容 所 6 10 6 10 4 6 10 6 8 10 10 極性 + - + - + - + - + - + - + - + - + - + - + - A ○ ○ 前 B ○ ○ 前 C ○ ○ 後 D ○ ○ 右 E ○ ○ 左

動作許容値 直接放電 接触放電・・・・・±6KV(マージン値±10KV) 気中放電・・・・・±8KV(マージン値±10KV) 間接放電 ・・・・・・±6KV(マージン値±10KV) 物理的許容値 ・・・・・・クラスに関係なく±10KV OKの場合: 〇 (動作許容値) NGの場合: × と NG内容を記入する。

設備・構成装置名 資産№ 型番 製造業者名精度 有効年月 静電気放電シミュレータ 546-0B2102 ESS-2000 ノイズ研究所 2014.01 デジタル温度計 540-1A0041 TRH-CZ 神榮㈱ ±0.5% 2014.01 ±3%RH 10 NEC Group internal useonly

図-1

放電箇所

(試験指示書抜粋)

静電気試験印加ポイント

静電気試験の印加ポイントを下記に示します。 (接触):接触放電、(気中):気中放電を表します。 ※黄色の矢印や数字では、印加ポイントを一部しか示していませんが、CPUブレードは、8Slot、 電源は、4台、FAN BOX は、5 台、SW モジュールは 6 台、全てが対象。 前面

3 12 5 6 10 14 4 7 8 9 13 11

2 21 18

15 19

20 16 17

1:イジェクトレバーネジ部(接触) 2:SUV コネクタ部(接触) 3:POW LED(気中) 4:POW SW(気中) 11 NEC Group internal useonly

5:STATUS LED(気中) 6:DUMP SW(気中) 7:LAN1 LED(気中) 8:RESET SW(気中) 9:LAN2 LED(気中) 10:ID SW(気中) 11:ID LED(気中) ※1~11は、全スロット(8 スロット)で実施。 12:Disk#0 LED(接触) 13:Disk#1LED(接触) ※ 12~13は、スロット5~6で実施。 14:ハンドル(左右)(接触) 15:収納ユニット前面(左右)(接触) 16:電源ユニットのイジェクトレバーネジ部(接触) ※電源ユニット 4 台分全てで実施。 17:I/F BOX 固定用ネジ部(接触) 18:ExpressScope 操作ボタン付近(気中) 19:リセットボタン(気中) 20:USB コネクタ付近(接触) 21:I/F Box イジェクトレバー(接触)

※水平結合版、垂直結合板を設置しての試験も実施。 (水平結合板:前:A、垂直結合板:前:B/後:C/右:D/左:E)

水平結合板:A

C 垂直結合板 :B

D

E 12 NEC Group internal useonly

背面 P2 写真を使用して下さい

23 22

24

25 27 28 29 30 26

38 31 35 36

32 33 34 37 39 40

22:収納ユニットねじ部(2箇所)(接触) 23:FAN-BOXイジェクトボタン(接触) 24:FAN-BOXハンドル(接触) ※23~24は、FAN-BOX 5 個分全てで実施。

25:10GbE インテリジェントスイッチ(L3)のイジェクトレバー(接触) 26:GbE インテリジェントスイッチ(L3)の USB コネクタ付近(接触) 27:GbE インテリジェントスイッチ(L3)の SFP+ポート1~4(接触) 28:GbE インテリジェントスイッチ(L3)の SFP+ポート 5~8(接触) 29:GbE インテリジェントスイッチ(L3)の QSFP+ポート1(接触) 30:GbE インテリジェントスイッチ(L3)の QSFP+ポート 2(接触) ※25~30は、L3 スイッチ(slot#1~6)全てで実施。 31:収容ユニットねじ部(2 箇所)(接触) 32:AC インレット LED(気中) 33:AC インレットロック機構部(接触) ※32~33は、電源 4 台分全てで実施。 34:CON-BOX シリアルポートねじ部(左右両方)(接触) 35:CON-BOX LAN ポート(左の方)(接触) 36:CON-BOX LAN ポート(右の方)(接触) 37:CON-BOX VGA コネクタねじ部(左右両方)(接触) 38:CON-BOX イジェクトレバー(接触) 39:CON-BOX KB コネクタ(接触) 40:CON-BOX MOUSE コネクタ(接触) 13 NEC Group internal useonly

※垂直結合板を設置しての試験も実施。(垂直結合板:前:B/後:C/右:D/左:E)

側面

41

42 43

41:ハンドル(接触) 42:ハンドル(接触) 43:脱落防止ロック機構部(接触) ※左右側面それぞれで、垂直結合板を設置しての試験も実施。 (垂直結合板:前:B/後:C/右:D/左:E)

14 NEC Group internal useonly

上面

45 44

46 47

44~47:天板(接触) 15 NEC Group internal useonly

印加ポイント 1

印加ポイント 31

以上

Issue Date: 2012-06-18 Page 1 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

Test Report issued under the responsibility of:

TEST REPORT IEC 60950-1 Information technology equipment - Safety - Part 1: General requirements Report Reference No ...... : E140190-A55-CB-3 Date of issue ...... : 2012-06-18 Total number of pages ...... : 24

CB Testing Laboratory ...... : UL Northbrook Address ...... : 333 Pfingsten Road, Northbrook, IL, 60062-2096, USA Applicant's name ...... : NEC CORP OF AMERICA SUITE 910 Address ...... : 500 PARK BLVD ITASCA IL 60143 UNITED STATES Test specification: Standard ...... : IEC 60950-1:2005 (2nd Edition); Am 1:2009 Test procedure ...... : CB Scheme Non-standard test method ...... : N/A Test Report Form No...... : IEC60950_1B Test Report Form originator ...... : SGS Fimko Ltd Master TRF ...... : 2010-04 Copyright © 2010 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved.

This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context.

If this test Report is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed.

This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 2 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

Test item description ...... : Blade Server and Chassis Trade Mark ...... :

Manufacturer ...... : NEC CORP 1-10 NISSIN-CHO FUCHU-SHI 183-8501 Model/Type reference ...... : EXP416A EXP416AD Ratings ...... : EXP416A: 100-120/200-240 Vac, 50 Hz/60 Hz, 61.5 A/68.5 A

or

-48 Vdc, 355 A

EXP416AD: -48 Vdc, 355 A

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 3 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

Testing procedure and testing location: [ ] CB Testing Laboratory Testing location / address ...... : [ ] Associated CB Test Laboratory Testing location / address ...... : Tested by (name + signature) ...... : Approved by (name + signature) ... : [ ] Testing Procedure: TMP Tested by (name + signature) ...... : Approved by (+ signature) ...... : Testing location / address ...... : [x] Testing Procedure: WMT Tested by (name + signature) ...... : Yoshinori Watari

Witnessed by (+ signature) ...... : Kathy Betts

Approved by (+ signature) ...... : David Piecuch

Testing location / address ...... : NEC 1-10 Nisshin-cho, Fuchu-city, Tokyo, Japan, 183-8501 [ ] Testing Procedure: SMT Tested by (name + signature) ...... : Approved by (+ signature) ...... : Supervised by (+ signature) ...... : Testing location / address ...... : [ ] Testing Procedure: RMT Tested by (name + signature) ...... : Approved by (+ signature) ...... : Supervised by (+ signature) ...... : Testing location / address ...... :

List of Attachments Differences (2 pages) Enclosures (8 pages) Summary Of Testing Unless otherwise indicated, all tests were conducted at NEC 1-10 Nisshin-cho, Fuchu-city, Tokyo, Japan, 183-8501. Tests performed (name of test and test clause) Testing location / Comments Humidity (2.9.1, 2.9.2, 5.2.2) Summary of Compliance with National Differences:

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 4 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

Countries outside the CB Scheme membership may also accept this report. List of countries addressed: AT, BE, BG, BY, CA, CH, CN, CZ, DE, DK, ES, EU, FI, FR, GB, GR, HU, IE, IL, IT, JP, KR, NL, NO, PL, PT, RO, SE, SG, SI, SK, UA, US

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 5 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

Copy of Marking Plate The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks.

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 6 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

Test item particulars : Equipment mobility ...... : stationary Connection to the mains ...... : pluggable A or B Operating condition ...... : continuous Access location ...... : operator accessible Over voltage category (OVC) ...... : OVC II Mains supply tolerance (%) or absolute mains supply values ...... : AC Mains: +10%, -10%, DC Mains: +20%, -15% Tested for IT power systems ...... : No IT testing, phase-phase voltage (V) ...... : N/A Class of equipment ...... : AC: Class I (earthed) Considered current rating of protective device as part of the building installation (A) ...... : 61.5A/68.5A Pollution degree (PD) ...... : PD 3 IP protection class ...... : IP X0 Altitude of operation (m) ...... : 2000m Altitude of test laboratory (m) ...... : up to 2000m Mass of equipment (kg) ...... : 199 kg Possible test case verdicts: - test case does not apply to the test object ...... : N / A - test object does meet the requirement ...... : P(Pass) - test object does not meet the requirement ...... : F(Fail) Testing: Date(s) of receipt of test item ...... : 2012-11-12 Date(s) of Performance of tests ...... : 2012-11-12, 2012-11-27 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the testing laboratory.

"(see Enclosure #)" refers to additional information appended to the report. "(see appended table)" refers to a table appended to the report.

Throughout this report a point is used as the decimal separator. Manufacturer's Declaration per Sub Clause 6.25 of IECEE 02: Not The application for obtaining a CB Test Certificate includes more than one factory and a Applicable declaration form the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided ......

When differences exist, they shall be identified in the General Product Information section. Name and address of Factory(ies): NEC COMPUTERTECHNO LTD 1088-3 OTSU-MACHI KOFU-SHI

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 7 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

YAMANASHI 400-0055 JAPAN

GENERAL PRODUCT INFORMATION:

Report Summary The original report was modified on 2013-01-14 to include the following changes/additions: E140190-A55-CB-3, Amendment 1 covers the evaluation of Model EXP416A to the National standard GB 4943.1-2011.

Product Description Blade Server

Model Differences Model differences are based on the power supply source used.

Additional Information Model EXP416A chassis may contain one or more of the following assemblies:

EXP405A up to 16 provided. EXP406A up to 16 provided. EXP407A up to 8 provided. EXP408A up to 8 provided. EXP409A up to 16 provided. EXP444A up to 8 provided. EXP443A up to 8 provided. EXP410A up to 16 provided. EXP417A up to 8 provided. EXP409B up to 16 provided. EXP410B up to 16 provided. EXP418A up to 16 provided. EXP419A up to 8 provided. EXP418B up to 8 provided. EXP433A up to 8 provided. EXP434A up to 8 provided. EXP435A up to 8 provided.

10Gb LL3 Switch (HUP700-HTGE) assembly up to 4 provided 4G FC Switch Assemblies up to 8 provided 8G FC Switch Assemblies up to 8 provided

Employs the marking: “Only used at altitude not exceeding 2000m.”

This Test Report is a reissue of CBTR Ref. No. E140190-A55-CB-2, CB Test Certificate Ref. No. US-17469- UL and US-15885-A2-UL. Based on previously conducted testing and the review of product technical documentation it was determined that the product complies with the upgrade of the Second Edition of the

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 8 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14 standard to Amendment 1. No sample was received for evaluation. All required tests were carried out during the original investigation. No testing was considered necessary to add alternate blades EXP418B, EXP433A, EXP434A, EXP435A, alternate SAS Controller manufactured by LSI Corp., type SAS9212-4i4e, to remove blade NX7700i from the Critical Component List, add an alternate instrumentation label type Carboglass C230C, manufactured by AGC POLYCARBONATE CO LTD, correct existing instrumentation label type 8B35 manufacturer to AGC POLYCARBONATE CO LTD, and to add alternate generic Lithium battery based on previous testing. Blades EXP434A and EXP435A are similar to EXP405A, and blades EXP418B and EXP433A are similar to EXP406A.

Technical Considerations  The product was submitted and evaluated for use at the maximum ambient temperature (Tma) permitted by the manufacturer’s specification of: 35°C  The means of connection to the mains supply is: Detachable power cord, Pluggable A or B  The product is intended for use on the following power systems: DC mains supply, TN  The equipment disconnect device is considered to be: Plug  The class of laser product is: Incorporates previously certified Class 1 laser source  The product was investigated to the following additional standards: IEC 60950-1 (2005) Second Edition, Additionally evaluated to EN 60950-1:2006/ A11:2009/A1:2010/, A12:2011; National Differences specified in the CB Test Report.  The following circuit locations (with circuit/schematic designation) were investigated as a limited power source (LPS): Output connectors  The following are available from the Applicant upon request: Specific data sheets for LEDs that are used for indicating purposes and are inherently Class 1 operating in the 400 - 700 nm wavelength range.,  The power supply in this equipment was: Not investigated. A test report for the power supply may be required when submitting this CB Report to a National Certification Body (NCB) to obtain a national mark.

Abbreviations used in the report: - normal condition ...... N.C.: - single fault condition ...... S.F.C: - operational insulation ...... OP: - basic insulation ...... BI: - basic insulation between parts of opposite - supplementary insulation ...... SI: polarity: BOP - double insulation ...... DI: - reinforced insulation ...... RI:

Indicate used abbreviations (if any)

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 9 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

2.9.2 Pass Humidity conditioning Evaluated during a separate power supply investigation. Tested for 120Hours. The entire unit was evaluated for 120 hours.

Relative humidity (%), temperature (°C) ... : - 95%, 40C

4.4.5.1 Considered to cause injury. c) ...... : Pass The inlet fan has an injury classification of c). (37.5mm, 8000rpm, & 0.07kg make a k-factor of 3780)

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 10 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

1.5.1 TABLE: list of critical components Pass object/part or manufacturer/ type/model technical data standard (Edition mark(s) of Description trademark or year) conformity1) Power Supply, Emerson (Astec AA25520L Input: UL 60950-1; UL, Nemko (up to 6 International Ltd) EN60950- provided) for AC 12.3 A, 100- 1:2001; A11 Version 120V, 50/60Hz (Additionally or 13.7A, 200- evaluated under 240V, 50/60Hz this evaluation)

Output:

80A +12V, 5A +5Vsb Maximum combined output power is 985W at 100-120V or

187A +12V, 5A +5Vsb Maximum combined output power is 2269W at 200-240V Power Supply Emerson (Astec AA26560L Input: UL 60950-1; EN UL, Demko (up to 6 International Ltd) 60950- provided) for 71A, -40.5 to - 1:2006/A11:2009 DCVersion 57V(DC) , EN 60950- 1:2006/A1:2010, Output: EN 60950- 1:2006 187A, +12V; (Additionally 5A, +5Vsb evaluated under Maximum this evaluation) combined output power is 2269W. Fan modules (up DENKI 9CR0812P8S04 12Vdc, 5.5 A UL 507, EN UL, TUV to 10 provided Co., Ltd. (160 CFM) 60950-1: 2001+A1 Enclosure Interchangeable Interchangeable Metal IEC 60950-1 -, Evaluated in this application PCB Interchangeable Interchangeable V-1, 105°C min UL796 UL, - Connectors Interchangeable Interchangeable V-2 min UL498, UL94, UL, - UL 1977 Connectors used Amphenol TCS AG722-00025 Suitable for UL498, UL94, UL, - for hot swapping (ATCS) current UL 1977 (female) (used interruption. V-2

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 11 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

for modules min. LL3 Switch, 4GFC Switch, 8GFC Switch, FC Pass- Through, 1Gb Pass-Through, 10Gb LL3 Switch) Connectors used Teradyne Models 439- Suitable for UL498, UL94, UL, - for hot swapping 3266-000,324- current UL 1977 (male) (used for 4005-004,324- interruption. V-2 G7JSZ(Mid- 4010-004,325- min. plane Board)) 4010-004,325- 4110-004, Connectors used FCI 10039755- Suitable for UL498, UL94, UL, - for hot swapping 10001TLF current UL 1977 (male) (used for interruption. V-2 G7JTB(Fan BP)) min. Connectors used FCI 10025026- Suitable for UL498, UL94, UL, - for hot swapping 10103TLF current UL 1977 (male) (used for interruption. V-2 G7JSY(EM min. Tray)) DVD UJDA780NE1-N 5Vdc, 1.8A UL 60950-1; UL, TUV Communications EN60950- Co., Ltd. 1:2001+A11; EN60825- 1:1994+A1+A2 DVD – alternate Interchangeable Interchangeable 5Vdc, 1.8A max. UL 60950-1, IEC UL, CENELEC Laser Class 1. 60950-1 Fuse (A04A) KOA CCF1N6.3T-TE 125V/6.3A UL 198; UL, - (Provided in IEC60127 G7JWU(USB Hub)) - non-user replaceable Lithium Battery Panasonic Corp. CR2032 3Vdc, 220mAh UL 1642, UL, - on G7JSX(EM Protected by Additionally Card) Diode A04A1 evaluated in this and Resistor application A04A2 (1kohm) Alternate Lithium Interchangeable Interchangeable 3Vdc, UL 1642 UL, - Battery 220mAh Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - for Enclosure Inc. Film Dev. Min. 0.2mm thick Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - for DVD Tray Inc. Film Dev. Min. 0.5mm thick Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, -

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 12 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

for G7JSX(EM Inc. Film Dev. Min. 0.2mm thick Card) Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - for G7JSY(EM Inc. Film Dev. Min. 0.2mm thick Tray) Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - for G7JTA (Fan- Inc. Film Dev. Min. 0.2mm thick ctrl Board) Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - for LCD Monitor Inc. Film Dev. Min. 0.2mm thick Insulation Sheet Mitsubishi DIALAMY VTM-0 Min. UL94 UL, - for G7JWU (USB Plastics,Inc 0.2mm thick Hub) Internal Plastic Interchangeable Interchangeable V-2 Min. UL 94 UL, - External Cover Interchangeable Interchangeable HB min. UL 94 UL, - for front Bezel EXP405A Blade NEC EXP405A - IEC 60950-1 -, - Assemblies (consist of the following) up to 16 provided. PTC (2A12, Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA 3A26) Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Seagate ST9146802SS 5Vdc/12Vdc UL60950-1, IEC UL, TUV (Max two 1.3A/0.5A max 60950-1 provided) Hard Disk Drive Interchangeable Interchangeable 5Vdc/12Vdc UL 60950-1, IEC UL, CENELEC Alternate - (Max 1.3A/0.5A max 60950-1 two provided) HDD face plate Interchangeable Interchangeable rated V-0 min UL 94 UL, - Lithium Battery Battery CR2032 3Vdc, 220mAh UL 1642 UL, - Co., Ltd. Protected by Diode B7E1 and Resistor B7E (1kohm) max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh; UL 1642 UL, - Battery Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA Battery Dallas DS1314 3V IEC 60950-1 -, Evaluated in Protection Circuit Semiconductor this application

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 13 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - for CPU Blade Inc. Film Dev. Min. 0.2mm thick EXP406A Blade NEC EXP406A - IEC60950-1 -, Evaluated in Assemblies this application (consist of the following) up to 16 provided PTC (2A13, Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA 3A25, 2W24) Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Lithium Battery Toshiba Battery CR2032 3Vdc, 220mAh UL 1642 UL, - Co., Ltd. Protected by Diode B7E1 and Resistor 6A20 (1kohm) max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh; UL 1642 UL, - Battery Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - for CPU Blade Inc. Film Dev. Min. 0.2mm thick Insulation Sheet Toray Industries Lumirror V-0 UL 94 UL, - for CPU Blade Inc. Film Dev. Min. 0.5mm thick EXP407A Blade NEC EXP407A - IEC 60950-1 -, Evaluated in Assemblies this application (consist of the following) up to 8 provided PTC (2A13, Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA 3A25, 2W24) Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Hard Disk Drive Seagate ST9146802SS 5Vdc/12Vdc UL60950-1, IEC UL, TUV (Max two 1.3A/0.5A max 60950-1 provided) Hard Disk Drive Interchangeable Interchangeable 5Vdc/12Vdc UL 60950-1, IEC UL, CENELEC Alternate - (Max 1.3A/0.5A max 60950-1 two provided) HDD face plate Interchangeable Interchangeable rated V-0 min UL 94 UL, - Lithium Battery Toshiba Battery CR2032 3Vdc, 220mAh; UL 1642 UL, - Co., Ltd. Protected by Diode B7E1 and

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 14 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

Resistor 6A20 (1kohm) max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh; UL 1642 UL, - Battery Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA Battery Back-up LSI Logic 01-01058 SELV UL 60950-1; IEC -, Evaluated in Module 60950-1 this application Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - for CPU Blade Inc. Film Dev. Min. 0.2mm thick Insulation Sheet Toray Industries Lumirror V-0 UL 94 UL, - for CPU Blade Inc. Film Dev. Min. 0.5mm thick EXP408A Blade NEC EXP408A - IEC 60950-1 -, Evaluated in Assemblies this application (consist of the following) up to 8 provided PTC (10A8, Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA 8A12) Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Hard Disk Drive Seagate ST936701SS 5Vdc/12Vdc UL60950-1, IEC UL, TUV (Max four 1.3A/0.5A max 60950-1 provided) Hard Disk Drive Interchangeable Interchangeable 5Vdc/12Vdc UL60950-1, UL, CENELEC Alternate 1.3A/0.5A max IEC60950-1 HDD face plate Interchangeable Interchangeable rated V-0 min UL 94 UL, - Lithium Battery Panasonic Corp. CR2032 3Vdc, 210mAh UL 1642 UL, - Protected by Diode 3S19 and Resistor 3S23 (1kohm) max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 210mAh; UL 1642 UL, - Battery Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA Battery Back-up LSI Logic 01-01058 SELV UL 60950-1; IEC -, Evaluated in Module 60950-1 this applcation

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 15 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

Battery Back-up LSI Logic L4-25126 SELV UL 60950-1; IEC -, Evaluated in Module 60950-1 this applcation Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - Inc. Film Dev. Min. 0.2mm thick Instrumention AGC 8B35 or VTM-2 UL 94 UL, - Label (Not POLYCARBONA Carboglass Marking Plate) TE CO LTD C230C Label Hashimoto Corp. Synthetic Paper 90 ºC, for UL 969, IEC UL, Evaluated in 80 application to 60950-1 this application steel EXP409A Blade NEC EXP409A - IEC 60950-1 -, Evaluated in Assemblies this application (consist of the following) up to 16 provided. PTC (2A9, 4A14) Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, TUV Corp. It 3.0A 60730-1, 3rd Hard Disk Drive Seagate ST9146802SS 5Vdc/12Vdc UL60950-1, IEC UL, Evaluated in (Max two 1.3A/0.5A max 60950-1 this application provided) to the current requirements of the standard. Hard Disk Drive Interchangeable Interchangeable 5Vdc/12Vdc UL 60950-1, IEC UL, Evaluated in Alternate - (Max 1.3A/0.5A max 60950-1 this application two provided) to the current requirements of the standard. HDD face plate Interchangeable Interchangeable rated V-0 min UL 94 UL, - Lithium Battery Toshiba Battery CR2032 Rated 3Vdc, UL 1642 UL, - Co., Ltd. 10mA max. charge current. Protected by Diode 7A31 and Resistor 7A44 (1kohm) Max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh; UL 1642 UL, - Battery Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - for CPU Blade Inc. Film Dev. Min. 0.2mm thick Rear Blade - - - IEC60950-1 -, Evaluated in Assemblies this application

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 16 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

(consist of the following) up to 8 provided PCB Interchangeable Interchangeable V-1, 105°C min UL796 UL, - LL3 Switch CISCO WS-CBS3020- 12Vdc, UL60950-1; -, Evaluated in (EXP423A) HPQ 30W max IEC60950-1 this application Assemblies (consist of the following) up to 8 provided Optical Avago AFBR-5715Z - 3.3Vdc, 300mA, UL 60950-1, EN UL, TUV Transceivers Technologies, may contain Class 1 Laser 60950-1, (optional) Agilent additional Product (850 EN 60825- Technologies suffixes nm) 1, EN 60825-2 4G FC Switch Brocade HSTNS-1B10 12Vdc, 3Ah UL 60950-1; IEC -, Evaluated in Assemblies 60950-1 this application (consist of the following) up to 8 provided Optical JDS Uniphase JSH-42S3AB3 3.3Vdc, 200mA, EN 60950, UL, TUV Transceivers Class 1 Laser EN 60825- (used on 4G FC Product, Optical 1, EN 60825-2 Switch) wavelength 850nm (U.S. Code of Federal Regulations, 21 CFR 1040 ) PCB Interchangeable Interchangeable V-1, 105°C min UL796 UL, - 8G FC Switch Brocade HSTNS-BC23-N 12Vdc, 3Ah UL 60950-1; IEC -, CSA, CE Assemblies 60950-1 (consist of the following) up to 8 provided Optical Brocade 57-1000012-01 3.3Vdc, 300mA, UL 60950-1, EN UL, TUV Transceivers Class 1 Laser 60950-1, (used on 8G FC Product (850 EN 60825- Switch) nm) 1, EN 60825-2 PCB Interchangeable Interchangeable V-1, 105°C min UL796 UL, - FC Pass- NEC EXP444A - IEC 60950-1 -, Evaluated in Through this application Assembly (consists of the following) up to 8 provided PCB Interchangeable Interchangeable V-1, 105°C min UL796 UL, - Insulation Sheet Toray Industries Lumirror VTM-2, Min 0.2 UL 94 UL, - Inc. Film Dev. mm thick

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 17 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

Optical Finisar FTLF8524P2BN Class 1 Laser UL 60950-1, EN UL, TUV; Transceivers V Product 60950:2000, EN Additionally (optional) , 3.3Vdc, 180mA 60825-1:1994 + evaluated during Optical A1+A2, EN end product Up to 16 wavelength 60825-2:2000. investigation and provided. 850nm (U.S. meet current Code of Federal requirements. Regulations, 21 CFR 1040 ) 1Gb Pass- NEC EXP443A - IEC 60950-1 -, Evaluated in Through this application Assembly (consists of the following) up to 8 provided PCB Interchangeable Interchangeable V-1, 105°C min UL796 UL, - Insulation Sheet Toray Industries Lumirror VTM-2, Min 0.2 UL 94 UL, - Inc. Film Dev. mm thick 10Gb LL3 Switch NEC 856-850991- 12 Vdc, 6A EN 60950-1 -, TUV (HUP700-HTGE) 026-A assembly (consists of the following) up to 4 provided PCB NEC EXP443A V-1, 105°C min UL796 UL, - EXP410A Blade NEC EXP410A - IEC 60950-1 -, Evaluated in Assemblies this application (consist of the following) up to 16 provided. PTC (2A10, Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA 4A27) Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Lithium Battery Toshiba Battery CR2032 3Vdc, 220mAh UL 1642 UL, - Co., Ltd. Protected by Diode 7T6 and Resistor 7T8 (1kohm) Max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh; UL 1642 UL, - Battery Protected with 1K ohm resistor in series with diode. Max reverse charging

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 18 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

current 10mA Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, - for CPU Blade Inc. Film Dev. Min. 0.2mm thick EXP417A Blade NEC EXP417A - IEC 60950-1 --, Evaluated in Assemblies this application (consist of the following) up to 8 provided Hard Disk Drive Seagate ST9146802SS 5Vdc/12Vdc UL60950-1, IEC UL, TUV (Max six 1.3A/0.5A max 60950-1 provided) Hard Disk Drive Interchangeable Interchangeable 5Vdc/12Vdc UL 60950-1, IEC UL, - Alternate - (Max 1.3A/0.5A max 60950-1 six provided) HDD face plate Interchangeable Interchangeable rated V-0 min UL 94 UL, - Lithium Battery Panasonic Corp. CR2032 3Vdc, 210mAh UL 1642 UL, - Protected by Diode 4B11 and Resistor 4B8 (1kohm) max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, UL 1642 UL, - Battery 210mAh; Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA Battery Back-up LSI Logic 01-25034 SELV UL 60950-1; IEC UL, UL Listed Module (incorporates 60950-1 (E257743); SCSI/SATA Further controller model evaluated in this 01144) application TAG Sheet Interchangeable Interchangeable V-2 min. UL 94 UL, - Insulation Sheet SUMITOMO PHF150 VTM-2 min. UL 94 UL, - BAKELITE CO (Rated VTM-0) LTD Instrumention AGC 8B35 or VTM-2 min UL 94 UL, - Label (Not POLYCARBONA Carboglass Marking Plate) TE CO LTD C230C Light Pipe Interchangeable Interchangeable HB UL 94 UL, - SAS Raid LSI Corp. 25121 3.3 Vdc/12Vdc UL 60950-1, IEC UL, Evaluated as Controller - 0.3A/1.81A max 60950-1 part of this optional investigation. SAS Raid LSI Corp. 01144 3.3 Vdc/12Vdc UL 60950-1, IEC UL, Evaluated as Controller – 17.6W max 60950-1 part of this

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 19 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

alternate - investigation. optional EXP419A Blade NEC EXP419A - IEC 60950-1 UL, Evaluated as Assemblies part of this (consist of the investigation. following) up to 8 provided Lithium Battery Panasonic Corp. CR2032 3Vdc, 210mAh UL 1642 UL, - Protected by Diode 6B19 and 1k ohm Resistor 6B9 Alternate Lithium Interchangeable Interchangeable 3Vdc, UL 1642 UL, - Battery 210mAh; Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA TAG Sheet Interchangeable Interchangeable V-2 min. UL 94 --, - Insulation Sheet TORAY Lumirror VTM-2 UL 94 UL, - INDUSTRIES INC Instrumention AGC 8B35 or VTM-2 UL 94 UL, - Label (Not POLYCARBONA Carboglass Marking Plate) TE CO LTD C230C Light Pipe Interchangeable Interchangeable HB UL 94 UL, - Cable Clump du Pont PA66 V-2 UL 94 UL, - (101F) LTO4 Drive HEWLETT BRSLA-0703-DC 5Vdc/12Vdc UL 60950-1, IEC UL, Further PACKARD LTD 3.5A/1.5A max 60950-1 Evaluated in this investigation SAS Controller LSI Corp. 01094 SELV, V-1 PWB, UL 94, IEC UL, Further Plastics Rated V- 60950-1 Evaluated in this 2 min. Rated investigation. 12Vdc 0.5A max. SAS Controller LSI Corp. SAS9212-4i4e 12Vdc, 0.67A IEC 60950-1 UL, - (Alternate) EXP409B Blade NEC EXP409B - IEC 60950-1 -, -- Assemblies (consist of the following) up to 16 provided. PTC (2A9, 4A14) Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3.

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 20 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

Clause 2.5 Hard Disk Drive Seagate ST9146802SS 5Vdc/12Vdc UL60950-1, IEC UL, TUV (Max two 1.3A/0.5A max 60950-1 provided) Hard Disk Drive Interchangeable Interchangeable 5Vdc/12Vdc UL 60950-1, IEC UL, CENELEC Alternate - (Max 1.3A/0.5A max 60950-1 two provided) HDD face plate Interchangeable Interchangeable rated V-0 min UL 94 UL, -- Lithium Battery Toshiba Battery CR2032 3Vdc, 220mAh UL 1642 UL, -- Co., Ltd. Protected by Diode 7A31 and 1K ohm Resistor, 7A44. Max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh UL 1642 UL, -- Battery Protected by Diode 7B7 and 1K ohm Resistor 7B3 Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, -- for CPU Blade Inc. Film Dev. Min. 0.2mm thick Air duct MITSUBISHI PC(0.38t) Rated V2 UL 94 UL, -- ENGINEERING S-3000VR PLASTICS CORP EXP410B Blade NEC EXP410B - IEC 60950-1 -, -- Assemblies (consist of the following) up to 16 provided. PTC (2A10, Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA 4A27) Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Lithium Battery Toshiba Battery CR2032 3Vdc, 220mAh UL 1642 UL, -- Co., Ltd. Protected by Diode 7T6 and 1 K ohm Resistor 7T8. Max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh; UL 1642 UL, -- Battery Protected with 1K ohm resistor in series with diode. Max reverse charging

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 21 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

current 10mA Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, -- for CPU Blade Inc. Film Dev. Min. 0.2mm thick EXP418A Blade NEC EXP418A - IEC 60950-1 -, -- Assemblies (consist of the following) up to 16 provided. PTC (2A, 4A5) Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Lithium Battery Toshiba Battery CR2032 3Vdc, 220mAh UL 1642 UL, -- Co., Ltd. Protected by Diode B7V6 and 1K ohm Resistor B7V4. Max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh; UL 1642 UL, -- Battery Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, -- for CPU Blade Inc. Film Dev. Min. 0.2mm thick Air duct MITSUBISHI PC(0.38t) Rated V2 min UL 94 UL, -- ENGINEERING S-3000VR PLASTICS CORP Duct Insulator TORAY Polyethylene Rated VTM-2 UL 94 UL, -- INDUSTRIES Terephthalate INC EXP418B Blade NEC EXP418B - - -, - Assemblies (consist of the following) up to 16 provided. PTC (2A, 4A5) Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Lithium Battery Toshiba Battery CR2032 3Vdc, 220mAh UL 1642 UL, -- Co., Ltd. Protected by Diode B7V6 and 1K ohm Resistor

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 22 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

B7V4. Max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh; UL 1642 UL, -- Battery Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, -- for CPU Blade Inc. Film Dev. Min. 0.2mm thick EXP433A Blade NEC EXP433A - - -, - Assemblies (consist of the following) up to 16 provided. PTC (B4A, Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA B2A4) Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Lithium Battery Toshiba Battery CR2032 3Vdc, 220mAh UL 1642 UL, -- Co., Ltd. Protected by Diode B6V20 and 1K ohm Resistor B6V17. Max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh; UL 1642 UL, -- Battery Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, -- for CPU Blade Inc. Film Dev. Min. 0.2mm thick EXP434A Blade NEC EXP434A - -, - Assemblies (consist of the following) up to 16 provided. PTC (4A15, 2A8) Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Lithium Battery Toshiba Battery CR2032 3Vdc, 220mAh UL 1642 UL, --

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 23 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

Co., Ltd. Protected by Diode 7B7 and 1K ohm Resistor 7B3. Max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh UL 1642 UL, -- Battery Protected by Diode 7B7 and 1K ohm Resistor 7B3 Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, -- for CPU Blade Inc. Film Dev. Min. 0.2mm thick EXP435A Blade NEC EXP435A - -, - Assemblies (consist of the following) up to 16 provided. PTC (4A15, 2A8) Tyco Electronics MiniSMDC150 Vmax 6V, UL 1434, IEC UL, CSA Corp. It 3.0A 60730-1, 3rd; IEC 60950, ed 3. Clause 2.5 Lithium Battery Toshiba Battery CR2032 3Vdc, 220mAh UL 1642 UL, -- Co., Ltd. Protected by Diode 7B7 and 1K ohm Resistor 7B3. Max reverse charging current 10mA Alternate Lithium Interchangeable Interchangeable 3Vdc, 220mAh; UL 1642 UL, -- Battery Protected with 1K ohm resistor in series with diode. Max reverse charging current 10mA Insulation Sheet Toray Industries Lumirror VTM-2 UL 94 UL, -- for CPU Blade Inc. Film Dev. Min. 0.2mm thick Supplementary information: 1) Provided evidence ensures the agreed level of compliance. See OD-CB2039.

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 24 of 24 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1 Clause Requirement + Test Result - Remark Verdict

5.2 TABLE: electric strength tests, impulse tests and voltage surge tests Pass Test voltage applied between: Voltage shape Test voltage Breakdown (AC, DC, (V) Yes / No impulse, surge) Functional: Test voltage applied between: Voltage shape Test voltage Breakdown (AC, DC, (V) Yes / No impulse, surge) Basic/supplementary: Test voltage applied between: Voltage shape Test voltage Breakdown (AC, DC, (V) Yes / No impulse, surge) Primary to Ground (Humidity) DC 2798 NO Reinforced: Test voltage applied between: Voltage shape Test voltage Breakdown (AC, DC, (V) Yes / No impulse, surge) Primary to Secondary (Humidity) AC 3000 NO supplementary information:

TRF No. : IEC60950_1B This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 1 of 2 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

Enclosure National Differences

Austria** Belarus* Belgium** Bulgaria** China* Czech Republic** Denmark Finland France** Greece** Group Hungary** Ireland Israel Italy** Japan* Korea ** Norway Poland** Portugal** Romania** Singapore* Slovakia** Slovenia** Spain Sweden Switzerland USA / Canada Ukraine* United Kingdom

* No National Differences Declared ** Only Group Differences

This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 2 of 2 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14

IEC 60950-1:2005 SubClause Difference + Test Result - Remark Verdict

NOTE: National differences are not listed for countries that have no declared national differences or that conform to previously stated Group differences.

This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 1 of 8 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14 Enclosures

Enclosures

Type Supplement Id Description Photographs 3-01 (EXP416A) Front Photographs 3-02 (EXP416A) Rear Photographs 3-03 EXP405A Blade Server Internal Photographs 3-04 EXP406A Blade Server Internal Photographs 3-05 EXP407A Blade Server Internal Photographs 3-06 EXP408A Blade Server Internal Photographs 3-07 NX7700i Blade Server Internal Photographs 3-08 LL3 Switch (EXP423A) Internal Photographs 3-09 FC Pass-Through Card (EXP444A) Internal Photographs 3-10 1Gb Pass-Through Card (EXP443A) Internal Photographs 3-11 10Gb LL3 Switch (856-850991-026-A) Internal Photographs 3-17 EXP409A Blade Server Internal Photographs 3-18 EXP410A Blade Server Internal View Photographs 3-19 EXP417A Blade Server Internal View Photographs 3-20 8G FC Switch Internal - Brocade Model HSTNS-BC23-N Photographs 3-23 EXP409B Blade Server Front Photographs 3-24 EXP409B Blade Server Internal Photographs 3-25 EXP409B Blade Server Rear Photographs 3-26 EXP410B Blade Server Front Photographs 3-27 EXP410B Blade Server Internal Photographs 3-28 EXP410B Blade Server Rear Photographs 3-29 EXP418A Blade Server Front Photographs 3-30 EXP418A Blade Server Internal (with air ducts removed) Photographs 3-31 EXP418A Blade Server Rear Photographs 3-32 EXP418A Blade Server Internal with Air Ducts Photographs 3-34 EXP419A Blade Server Internal View Photographs 3-35 EXP419A Blade Server Overall View Photographs 3-36 Rear View with DC Source Photographs 3-37 EXP418B Blade Server Front Photographs 3-38 EXP418B Blade Server Internal with air ducts removed Photographs 3-39 EXP418B Blade Server Internal with air ducts Photographs 3-40 EXP433A Blade Server Internal View

This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 2 of 8 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14 Enclosures

Photographs 3-41 EXP433A Blade Server Overall View Photographs 3-42 EXP434A Blade Server Internal View Photographs 3-43 EXP434A Blade Server Overall View Photographs 3-44 EXP435A Blade Server Internal View Photographs 3-45 EXP435A Blade Server Overall View Diagrams Schematics + PWB 5-01 EXP408A Blade Server battery circuit Schematics + PWB 5-02 EXP408A Blade Server ROMB battery circuit Schematics + PWB 5-03 EXP405A Blade Server battery circuit Schematics + PWB 5-04 EXP406A Blade Server battery circuit Schematics + PWB 5-05 EXP407A Blade Server battery circuit Schematics + PWB 5-06 G7JSX(EM Card) battery circuit Schematics + PWB 5-08 EXP409A Blade Server battery circuit (representative of EXP409B) Schematics + PWB 5-09 Schematic EXP410A PTC (representative of EXP410B, EXP418A) Schematics + PWB 5-10 Schematic EXP410A Lithium Battery Protection Circuit (representative of EXP410B, EXP418A) Schematics + PWB 5-11 Schematic EXP417A Lithium Battery Protection Circuit Schematics + PWB 5-12 Schematic, EXP419A Lithium Battery Protection Schematics + PWB 5-13 Schematic, EXP418B Lithium Battery Protection Schematics + PWB 5-14 Schematic, EXP433A Lithium Battery Protection Schematics + PWB 5-15 Schematic, EXP434A Lithium Battery Protection Schematics + PWB 5-16 Schematic, EXP435A Lithium Battery Protection Manuals 6-01 EXP416A Installation (N8405-040F Blade Enclosure (SIGMABLADE-H) User's Guide) Manuals 6-02 EXP405A Installation (Express5800/120Bb-6 User's Guide) Manuals 6-03 EXP406A Installation (Express5800/120Bb-d6 User's Guide) Manuals 6-04 EXP407A Installation (Express5800/120Bb-m6 User's Guide) Manuals 6-05 EXP408A Installation (Express5800/B140a-T User's Guide) Manuals 6-06 NX7700i Installation (NX7700i/5010B-4 User's Guide) Manuals 6-07 LL3 Switch (EXP423A) Installation (N8406-023 1Gb Intelligent L3 Switch User's Guide) Manuals 6-08 1Gb Pass-Through Card (EXP443A) / FC Pass-Through Card (EXP444A) Installation (N8406-029 1Gb Pass-Through Card / N8406-030 FC Pass-Through Card User's Guide) Manuals 6-09 10Gb LL3 Switch Installation (N8406-026 10Gb Intelligent L3 Switch User's Guide) Miscellaneous 7-02 Caution/Warning Label Miscellaneous 7-04 Cal Certs

This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 3 of 8 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14 Enclosures

Miscellaneous 7-05 Letter of Assurance Miscellaneous 7-06 China National Differences (National standard GB 4943.1--2011) Licenses 8-01 Power Supply Licenses 8-02 Transceivers, Finisar Licenses 8-03 Fans Licenses 8-04 PTC Licenses 8-07 DVD ROM Licenses 8-09 Transceiver, Avago Technologies Licenses 8-10 Transceiver, JDS Uniphase Licenses 8-11 10Gb LL3 Switch Licenses 8-12 Panasonic Battery Licenses 8-13 Toshiba Battery Licenses 8-14 License, TUV, Transceiver, Brocade, Model 57-1000012-01 Licenses 8-15 License, VDE, Fan, Delta GFC0812DW Licenses 8-16 Power supply AA26560L Marking Plate

This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 4 of 8 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14 Enclosures

Misc ID 7-06

This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 5 of 8 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14 Enclosures

Misc ID 7-06

This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 6 of 8 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14 Enclosures

Misc ID 7-06

This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 7 of 8 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14 Enclosures

Misc ID 7-06

This report issued under the responsibility of UL Issue Date: 2012-06-18 Page 8 of 8 Report Reference # E140190-A55-CB-3 Amendment 1 2013-01-14 Enclosures

Misc ID 7-06

This report issued under the responsibility of UL