Database Schema

User Guides

IDC DOCUMENTATION Database Schema

Revision 5 Notice This document was published by the Monitoring Systems Operation of Science Applications International Corporation (SAIC) as part of the International Data Centre (IDC) Documentation. It was first published in 1998 and was republished as Revision 1 in March 1999 and then again as Revision 2 in November 2000 to include major changes. This third revision of the document was published electronically as Revision 3 in October 2002. The fourth and fifth revisions of the document were published by Veridian Systems in August 2002 and October 2002, respectively; these include changes only to the radionuclide sections of the document. IDC documents that have been changed substantially are indicated by a whole revision number (for example, Revision 1).

Contributors Jerry A. Carter, Science Applications International Corporation Roger Bowman, Science Applications International Corporation Kendra Biegalski, Veridian Systems Mark D. Fisk, Mission Research Corporation Richard J. Carlson, Mission Research Corporation Pat Donohoe, Veridian Systems William E. Farrell, Science Applications International Corporation Bonnie MacRitchie, Science Applications International Corporation Hallie Magyar, Veridian Systems

Trademarks Ethernet is a registered trademark of Xerox Corporation. ORACLE is a registered trademark of Oracle Corporation. Solaris is a registered trademark of Sun Microsystems. SPARC is a registered trademark of Sun Microsystems. SQL*Plus is a registered trademark of Oracle Corporation. UNIX is a registered trademark of UNIX System Labs, Inc.

Ordering Information The ordering number for this document is TN2924 through Veridian Systems. Notice Page This document is cited within other IDC documents as [IDC5.1.1Rev5].

Database Schema

October 2002 IDC-5.1.1Rev5 TABLE OF CONTENTS

About this Document xxi

• PURPOSE xxii

• SCOPE xxii

• AUDIENCE xxii

• RELATED INFORMATION xxii

• USING THIS DOCUMENT xxiii

Chapter 1: S/H/I Entity Relationships 1

• OVERVIEW 2

• FUNDAMENTAL TABLES 6

• REFERENCE TABLES 13

• S/H/I APPLICATION SOFTWARE TABLES 16

• HISTORICAL DATA TABLES 30

Chapter 2: S/H/I Table Descriptions 33

• AFFILIATION, STANET 34

• ALLOCATE_HOUR 35

• ALLOW_RESID 36

• ALPHASITE 37

• AMP3C 38

• AMPDESCRIPT 39

• AMPLITUDE 40

• APMA 42

• ARCH_DATA_TYPE 44

• ARRIVAL 45

• ASSOC, ASSOC_TEMP_GA 47

• ATTENCOEF 49

• BEAMAUX 50

• BULL_COMP 51

• CEPPKS 53

i TABLE OF CONTENTS

• CHAN_GROUPS 54

• CHANNAME 55

• COLORDISC 56

• COMPLEXITY 57

• DATADAYS 58

• DATAREADY 59

• DATAUSER 60

• DETECTION 62

• DISCARD 64

• DLFILE 65

• DLMAN 67

• EV_SUMMARY, EX_SUMMARY, AN_SUMMARY 68

• EVENT 70

• EVENT_CONTROL, IN_EVENT_CONTROL 71

• EVSC_HYDRO 73

• EVSC_PROD 74

• EVSC_REGIONAL 76

• EX_AN 78

• EXCEPTION_CHANMAP 80

• EXPLO 81

• FILEPRODUCT, FS_STAGEPRODUCT 83

• FKDISC 84

• FORBEAMAUX 86

• FPDESCRIPTION 87

• FSAVE 88

• FSDISC 89

• FSRECIPE 91

• FSTAG 92

ii TABLE OF CONTENTS

• FTPFAILED 93

• FTPLOGIN 94

• FWFILE 95

• FWGAP 96

• FWSITE 97

• GA_TAG 98

• GLOSSARY 99

• GREGION 100

• HYDRO_ARR_GROUP 101

• HYDRO_ASSOC 102

• HYDRO_FEATURES 103

• INFRA_FEATURES 105

• INSTRUMENT 107

• INTERVAL 108

• LASTID, PROBLASTID, RMS_LASTID 109

• LOCATION 110

• MAPCOLOR 111

• MAPDISC 112

• MAPOVER 114

• MAPPOINT 115

• MIG_DATE 116

• MIG_RULES 117

• MSGAUX 118

• MSGDATATYPE 119

• MSGDEST 120

• MSGDISC 121

• NA_VALUE 123

• NETMAG 124

iii TABLE OF CONTENTS

• NETWORK 125

• ORIGAUX 126

• ORIGERR, ORIGERR_TEMP_GA 127

• ORIGIN, ORIGINREF, ORIGIN_TEMP_GA 128

• OUTAGE 130

• OVERLAYDISC 131

• PARRIVAL 132

• PARTICIPATION 133

• PROBLEM 134

• PROBLEMLOG 135

• PROBLEMMAIL 136

• PRODTRACK 137

• PRODUCTCRITERIA 138

• PRODUCTTYPEEVSC 140

• PRODUCTTYPEORIGIN 142

• PRODUCTTYPESTA 144

• QCSTATS 145

• REBDONE_DATADAY_FLAG 147

• REF_LOC 148

• REGCOEF 149

• REMARK 150

• REQUEST 151

• REVAUDIT 153

• SCAN_DATE 154

• SEISGRID, DSEISGRID 155

• SEISINDEX, DSEISINDEX 156

• SENSOR 157

• SITE 159

iv TABLE OF CONTENTS

• SITE_ADDRESS 160

• SITEAUX 161

• SITECHAN 162

• SITEPOLL 163

• SPLP 164

• SPVAR 165

• SREGION 166

• STAMAG 167

• STASSOC 169

• STD_CHANMAP 170

• SUBS 171

• SUBSUSER 172

• THIRDMOM 173

• TIMEFREQ 174

• TIMESTAMP 175

• WEIGHTS 176

• WFAUX 177

• WFCONV 178

• WFDISC, WFPROTO 180

• WFTAG 182

• XTAG 183

Chapter 3: S/H/I Column Descriptions 185

• RANGES 186

• NA VALUES 186

• COLUMNS 187

Chapter 4: Radionuclide Database Overview 413

• TWO-TIER DATABASE SCHEMA 414

• DATABASE ORGANIZATION 414

v TABLE OF CONTENTS

• RADIONUCLIDE OBJECT DESCRIPTIONS 419

Chapter 5: Radionuclide Entity Relationships 441

• OVERVIEW 442

• RADIONUCLIDE TABLES 442

Chapter 6: Radionuclide Table Descriptions 455

• GARDS_ALERTS 456

• GARDS_AUTO_SAMPLE_CAT 457

• GARDS_AUX_LIB 458

• GARDS_AUX_LINES_LIB 459

• GARDS_B_ENERGY_PAIRS 460

• GARDS_B_ENERGY_PAIRS_ORIG 461

• GARDS_B_RESOLUTION_PAIRS 462

• GARDS_B_RESOLUTION_PAIRS_ORIG 463

• GARDS_BG_EFFICIENCY_PAIRS 464

• GARDS_BG_ENERGY_CAL 465

• GARDS_CAT_CRITERIA_TESTS 466

• GARDS_CAT_TEMPLATE 467

• GARDS_CODES 469

• GARDS_COMMENTS 470

• GARDS_COMMENTS_DEFS 471

• GARDS_CSC_MODCOEFF_LIB 472

• GARDS_DATA_LOG 473

• GARDS_DBROLE_OWNER 474

• GARDS_DETECTORS 475

• GARDS_DIST_SAMPLE_QUEUE 476

• GARDS_EFFICIENCY_CAL 477

• GARDS_EFFICIENCY_PAIRS 478

• GARDS_ENERGY_CAL 479

vi TABLE OF CONTENTS

• GARDS_ENERGY_CAL_ORIG 481

• GARDS_ENERGY_PAIRS 483

• GARDS_ENERGY_PAIRS_ORIG 484

• GARDS_ENVIRONMENT 485

• GARDS_FLAGS 486

• GARDS_FPE 487

• GARDS_HISTOGRAM 488

• GARDS_INTERVAL 489

• GARDS_MDAS2REPORT 490

• GARDS_MET_DATA 491

• GARDS_NOTIFY 492

• GARDS_NUCL2QUANTIFY 493

• GARDS_NUCL_IDED 494

• GARDS_NUCL_IDED_ORIG 497

• GARDS_NUCL_LIB 499

• GARDS_NUCL_LINES_IDED 500

• GARDS_NUCL_LINES_IDED_ORIG 502

• GARDS_NUCL_LINES_LIB 504

• GARDS_PEAKS 505

• GARDS_PEAKS_ORIG 508

• GARDS_PERMISSIONS 511

• GARDS_POC 512

• GARDS_PROC_PARAMS_TEMPLATE 513

• GARDS_PROCESSING_ERRORS 516

• GARDS_QAT_CONFIG 517

• GARDS_QAT_NOTIFY 518

• GARDS_QAT_QUERY_FILTER 519

• GARDS_QCHISTORY 520

vii TABLE OF CONTENTS

• GARDS_QCPARAMS 521

• GARDS_QCTARGETS 522

• GARDS_QUERY_RESULTS 523

• GARDS_READ_SAMPLE_STATUS 524

• GARDS_RECEIPT_LOG 525

• GARDS_REFLINE_MASTER 526

• GARDS_RELEVANT_NUCLIDES 527

• GARDS_RESOLUTION_CAL 528

• GARDS_RESOLUTION_CAL_ORIG 529

• GARDS_RESOLUTION_PAIRS 530

• GARDS_RESOLUTION_PAIRS_ORIG 531

• GARDS_RLR 532

• GARDS_ROI_CHANNELS 533

• GARDS_ROI_CONCS 534

• GARDS_ROI_COUNTS 535

• GARDS_ROI_LIB 536

• GARDS_ROI_LIMITS 537

• GARDS_ROLES 538

• GARDS_ROLES_PERMISSIONS 539

• GARDS_SAMPLE_AUX 540

• GARDS_SAMPLE_CAT 541

• GARDS_SAMPLE_CERT 542

• GARDS_SAMPLE_CERT_LINES 543

• GARDS_SAMPLE_DATA 544

• GARDS_SAMPLE_DESCRIPTION 546

• GARDS_SAMPLE_FLAGS 547

• GARDS_SAMPLE_PROC_PARAMS 548

• GARDS_SAMPLE_RATIOS 551

viii TABLE OF CONTENTS

• GARDS_SAMPLE_STATUS 552

• GARDS_SAMPLE_UPDATE_PARAMS 553

• GARDS_SAMPLE_XE_PROC_PARAMS 554

• GARDS_SOH_CHAR_DATA 555

• GARDS_SOH_CODE 556

• GARDS_SOH_HEADER 557

• GARDS_SOH_NUM_DATA 558

• GARDS_SOH_SENSOR_DATA 559

• GARDS_SPECTRUM 560

• GARDS_STADET 561

• GARDS_STATION_ASSIGNMENTS 562

• GARDS_STATIONS 563

• GARDS_STATIONS_SCHEDULE 564

• GARDS_STATUS_HISTORY 565

• GARDS_TOTAL_EFFIC 566

• GARDS_TRENDVUE 567

• GARDS_UPDATE_PARAMS_TEMPLATE 568

• GARDS_UPDATE_REFLINES 569

• GARDS_USER_COMMENTS 570

• GARDS_USERENV 571

• GARDS_USERS 572

• GARDS_USERS_ROLES 573

• GARDS_XE_NUCL_LIB 574

• GARDS_XE_NUCL_LINES_LIB 575

• GARDS_XE_PROC_PARAMS_TEMPLATE 576

Chapter 7: Radionuclide Column Descriptions 579

References 669

Glossary 673

ix LIST OF FIGURES

FIGURE 1. SAMPLE ENTITY RELATIONSHIP 4

FIGURE 2. RELATIONSHIPS BETWEEN FUNDAMENTAL S/H/I TABLES 7

FIGURE 3. EVENT TABLE RELATIONSHIPS 9

FIGURE 4. DETAIL TABLES RELATED TO ARRIVAL 10

FIGURE 5. MEASUREMENT TABLE RELATIONSHIPS 11

FIGURE 6. EVENT CHARACTERIZATION TABLE RELATIONSHIPS 12

FIGURE 7. WAVEFORM TABLE RELATIONSHIPS 13

FIGURE 8. REFERENTIAL CORE TABLE RELATIONSHIPS 14

FIGURE 9. NETWORK TABLE RELATIONSHIPS 15

FIGURE 10. CHANNEL TABLE RELATIONSHIPS 16

FIGURE 11. RELATIONSHIPS OF TABLES USED IN AUTOMATIC PROCESSING 17

FIGURE 12. EVENT SCREENING TABLE RELATIONSHIPS 18

FIGURE 13. TABLES INVOLVED IN ANALYST REVIEW OF TIME-SERIES DATA 19

FIGURE 14. MAP TABLE RELATIONSHIPS 20

FIGURE 15. RELATIONSHIPS AMONG TABLES USED TO RECORD SPECTRUMS OF TIME-SERIES DATA 21

FIGURE 16. TABLES USED BY DISTRIBUTED PROCESSING APPLICATIONS 22

FIGURE 17. CONTINUOUS DATA SUBSYSTEM TABLE RELATIONSHIPS 23

FIGURE 18. MESSAGE SUBSYSTEM TABLE RELATIONSHIPS 24

FIGURE 19. SUBSCRIPTION SUBSYSTEM TABLE RELATIONSHIPS 25

FIGURE 20. MESSAGE AND SUBSCRIPTION SUBSYSTEM SUPPORT TABLES 26

FIGURE 21. DATA ARCHIVING SUBSYSTEM TABLES 27

FIGURE 22. TABLES USED BY SYSTEM MONITORING APPLICATIONS 28

FIGURE 23. TABLES USED FOR PERFORMANCE MONITORING 29

FIGURE 24. TABLES USED TO SUPPORT SCHEMA 30

FIGURE 25. TABLES USED TO DESCRIBE EXPLOSIONS 31

FIGURE 26. RADIONUCLIDE EQUIPMENT 443

FIGURE 27. RAW SENSOR DATA 444

FIGURE 28. RAW PULSE HEIGHT DATA 445

FIGURE 29. RAW PARTICULATE CALIBRATION DATA 446

x LIST OF FIGURES

FIGURE 30. RAW NOBLE GAS DATA 447

FIGURE 31. CALCULATED PARTICULATE CALIBRATION DATA 448

FIGURE 32. CALCULATED PARTICULATE DETECTION AND CHARACTERIZATION DATA 449

FIGURE 33. PARTICULATE PARAMETER AND STATUS DATA 450

FIGURE 34. CALCULATED NOBLE GAS DETECTION DATA 451

FIGURE 35. NOBLE GAS PARAMETER AND STATUS DATA 452

FIGURE 36. ANALYST COMMENT DATA 453

FIGURE 37. MULTIPLE ANALYST REVIEW DATA 454

xi LIST OF TABLES

TABLE 1: SYNTAX USED TO INDICATE DATABASE TABLE RELATIONSHIPS 3

TABLE 2: AFFILIATION (STANET) 34

TABLE 3: ALLOCATE_HOUR 35

TABLE 4: ALLOW_RESID 36

TABLE 5: ALPHASITE 37

TABLE 6: AMP3C 38

TABLE 7: AMPDESCRIPT 39

TABLE 8: AMPLITUDE 40

TABLE 9: APMA 42

TABLE 10: ARCH_DATA_TYPE 44

TABLE 11: ARRIVAL 45

TABLE 12: ASSOC (ASSOC_TEMP_GA) 47

TABLE 13: ATTENCOEF 49

TABLE 14: BEAMAUX 50

TABLE 15: BULL_COMP 51

TABLE 16: CEPPKS 53

TABLE 17: CHAN_GROUPS 54

TABLE 18: CHANNAME 55

TABLE 19: COLORDISC 56

TABLE 20: COMPLEXITY 57

TABLE 21: DATADAYS 58

TABLE 22: DATAREADY 59

TABLE 23: DATAUSER 60

TABLE 24: DETECTION 62

TABLE 25: DISCARD 64

TABLE 26: DLFILE 65

TABLE 27: DLMAN 67

TABLE 28: EV_SUMMARY (EX_SUMMARY, AN_SUMMARY) 68

TABLE 29: EVENT 70

TABLE 30: EVENT_CONTROL (IN_EVENT_CONTROL) 71

xii LIST OF TABLES

TABLE 31: EVSC_HYDRO 73

TABLE 32: EVSC_PROD 74

TABLE 33: EVSC_REGIONAL 76

TABLE 34: EX_AN 78

TABLE 35: EXCEPTION_CHANMAP 80

TABLE 36: EXPLO 81

TABLE 37: FILEPRODUCT (FS_STAGEPRODUCT) 83

TABLE 38: FKDISC 84

TABLE 39: FORBEAMAUX 86

TABLE 40: FPDESCRIPTION 87

TABLE 41: FSAVE 88

TABLE 42: FSDISC 89

TABLE 43: FSRECIPE 91

TABLE 44: FSTAG 92

TABLE 45: FTPFAILED 93

TABLE 46: FTPLOGIN 94

TABLE 47: FWFILE 95

TABLE 48: FWGAP 96

TABLE 49: FWSITE 97

TABLE 50: GA_TAG 98

TABLE 51: GLOSSARY 99

TABLE 52: GREGION 100

TABLE 53: HYDRO_ARR_GROUP 101

TABLE 54: HYDRO_ASSOC 102

TABLE 55: HYDRO_FEATURES 103

TABLE 56: INFRA_FEATURES 105

TABLE 57: INSTRUMENT 107

TABLE 58: INTERVAL 108

TABLE 59: LASTID (PROBLASTID, RMS_LASTID) 109

TABLE 60: LOCATION 110

xiii LIST OF TABLES

TABLE 61: MAPCOLOR 111

TABLE 62: MAPDISC 112

TABLE 63: MAPOVER 114

TABLE 64: MAPPOINT 115

TABLE 65: MIG_DATE 116

TABLE 66: MIG_RULES 117

TABLE 67: MSGAUX 118

TABLE 68: MSGDATATYPE 119

TABLE 69: MSGDEST 120

TABLE 70: MSGDISC 121

TABLE 71: NA_VALUE 123

TABLE 72: NETMAG 124

TABLE 73: NETWORK 125

TABLE 74: ORIGAUX 126

TABLE 75: ORIGERR (ORIGERR_TEMP_GA) 127

TABLE 76: ORIGIN (ORIGINREF, ORIGIN_TEMP_GA) 128

TABLE 77: OUTAGE 130

TABLE 78: OVERLAYDISC 131

TABLE 79: PARRIVAL 132

TABLE 80: PARTICIPATION 133

TABLE 81: PROBLEM 134

TABLE 82: PROBLEMLOG 135

TABLE 83: PROBLEMMAIL 136

TABLE 84: PRODTRACK 137

TABLE 85: PRODUCTCRITERIA 138

TABLE 86: PRODUCTTYPEEVSC 140

TABLE 87: PRODUCTTYPEORIGIN 142

TABLE 88: PRODUCTTYPESTA 144

TABLE 89: QCSTATS 145

TABLE 90: REBDONE_DATADAY_FLAG 147

xiv LIST OF TABLES

TABLE 91: REF_LOC 148

TABLE 92: REGCOEF 149

TABLE 93: REMARK 150

TABLE 94: REQUEST 151

TABLE 95: REVAUDIT 153

TABLE 96: SCAN_DATE 154

TABLE 97: SEISGRID (DSEISGRID) 155

TABLE 98: SEISINDEX (DSEISINDEX) 156

TABLE 99: SENSOR 157

TABLE 100: SITE 159

TABLE 101: SITE_ADDRESS 160

TABLE 102: SITEAUX 161

TABLE 103: SITECHAN 162

TABLE 104: SITEPOLL 163

TABLE 105: SPLP 164

TABLE 106: SPVAR 165

TABLE 107: SREGION 166

TABLE 108: STAMAG 167

TABLE 109: STASSOC 169

TABLE 110: STD_CHANMAP 170

TABLE 111: SUBS 171

TABLE 112: SUBSUSER 172

TABLE 113: THIRDMOM 173

TABLE 114: TIMEFREQ 174

TABLE 115: TIMESTAMP 175

TABLE 116: WEIGHTS 176

TABLE 117: WFAUX 177

TABLE 118: WFCONV 178

TABLE 119: WFDISC (WFPROTO) 180

TABLE 120: WFTAG 182

xv LIST OF TABLES

TABLE 121: XTAG 183

TABLE 122: GUIDELINES AND EXAMPLES OF NA VALUES 187

TABLE 123: DATABASE TABLE GROUPS 416

TABLE 124: RMSAUTO INDEXES 420

TABLE 125: RMSAUTO UNIQUE DATA CONSTRAINTS 422

TABLE 126: RMSAUTO PRIMARY KEY CONSTRAINTS 422

TABLE 127: RMSAUTO FOREIGN KEY CONSTRAINTS 422

TABLE 128: RMSAUTO COLUMN CONSTRAINTS 426

TABLE 129: RMSAUTO SYNONYMS 426

TABLE 130: RMSAUTO TRIGGERS 429

TABLE 131: RMSMAN INDEXES 434

TABLE 132: RMSMAN UNIQUE DATA CONSTRAINTS 435

TABLE 133: RMSMAN PRIMARY KEY CONSTRAINTS 435

TABLE 134: RMSMAN FOREIGN KEY CONSTRAINTS 436

TABLE 135: RMSMAN COLUMN CONSTRAINTS 438

TABLE 136: RMSMAN SEQUENCES 438

TABLE 137: RMSMAN SYNONYMS 439

TABLE 138: RMSMAN TRIGGERS 440

TABLE 139: GARDS_ALERTS 456

TABLE 140: GARDS_AUTO_SAMPLE_CAT 457

TABLE 141: GARDS_AUX_LIB 458

TABLE 142: GARDS_AUX_LINES_LIB 459

TABLE 143: GARDS_B_ENERGY_PAIRS 460

TABLE 144: GARDS_B_ENERGY_PAIRS_ORIG 461

TABLE 145: GARDS_B_RESOLUTION_PAIRS 462

TABLE 146: GARDS_B_RESOLUTION_PAIRS_ORIG 463

TABLE 147: GARDS_BG_EFFICIENCY_PAIRS 464

TABLE 148: GARDS_BG_ENERGY_CAL 465

TABLE 149: GARDS_CAT_CRITERIA_TESTS 466

TABLE 150: GARDS_CAT_TEMPLATE 467

xvi LIST OF TABLES

TABLE 151: GARDS_CODES 469

TABLE 152: GARDS_COMMENTS 470

TABLE 153: GARDS_COMMENTS_DEFS 471

TABLE 154: GARDS_CSC_MODCOEFF_LIB 472

TABLE 155: GARDS_DATA_LOG 473

TABLE 156: GARDS_DBROLE_OWNER 474

TABLE 157: GARDS_DETECTORS 475

TABLE 158: GARDS_DIST_SAMPLE_QUEUE 476

TABLE 159: GARDS_EFFICIENCY_CAL 477

TABLE 160: GARDS_EFFICIENCY_PAIRS 478

TABLE 161: GARDS_ENERGY_CAL 479

TABLE 162: GARDS_ENERGY_CAL_ORIG 481

TABLE 163: GARDS_ENERGY_PAIRS 483

TABLE 164: GARDS_ENERGY_PAIRS_ORIG 484

TABLE 165: GARDS_ENVIRONMENT 485

TABLE 166: GARDS_FLAGS 486

TABLE 167: GARDS_FPE 487

TABLE 168: GARDS_HISTOGRAM 488

TABLE 169: GARDS_INTERVAL 489

TABLE 170: GARDS_MDAS2REPORT 490

TABLE 171: GARDS_MET_DATA 491

TABLE 172: GARDS_NOTIFY 492

TABLE 173: GARDS_NUCL2QUANTIFY 493

TABLE 174: GARDS_NUCL_IDED 494

TABLE 175: GARDS_NUCL_IDED_ORIG 497

TABLE 176: GARDS_NUCL_LIB 499

TABLE 177: GARDS_NUCL_LINES_IDED 500

TABLE 178: GARDS_NUCL_LINES_IDED_ORIG 502

TABLE 179: GARDS_NUCL_LINES_LIB 504

TABLE 180: GARDS_PEAKS 505

xvii LIST OF TABLES

TABLE 181: GARDS_PEAKS_ORIG 508

TABLE 182: GARDS_PERMISSIONS 511

TABLE 183: GARDS_POC 512

TABLE 184: GARDS_PROC_PARAMS_TEMPLATE 513

TABLE 185: GARDS_PROCESSING_ERRORS 516

TABLE 186: GARDS_QAT_CONFIG 517

TABLE 187: GARDS_QAT_NOTIFY 518

TABLE 188: GARDS_QAT_QUERY_FILTER 519

TABLE 189: GARDS_QCHISTORY 520

TABLE 190: GARDS_QCPARAMS 521

TABLE 191: GARDS_QCTARGETS 522

TABLE 192: GARDS_QUERY_RESULTS 523

TABLE 193: GARDS_READ_SAMPLE_STATUS 524

TABLE 194: GARDS_RECEIPT_LOG 525

TABLE 195: GARDS_REFLINE_MASTER 526

TABLE 196: GARDS_RELEVANT_NUCLIDES 527

TABLE 197: GARDS_RESOLUTION_CAL 528

TABLE 198: GARDS_RESOLUTION_CAL_ORIG 529

TABLE 199: GARDS_RESOLUTION_PAIRS 530

TABLE 200: GARDS_RESOLUTION_PAIRS_ORIG 531

TABLE 201: GARDS_RLR 532

TABLE 202: GARDS_ROI_CHANNELS 533

TABLE 203: GARDS_ROI_CONCS 534

TABLE 204: GARDS_ROI_COUNTS 535

TABLE 205: GARDS_ROI_LIB 536

TABLE 206: GARDS_ROI_LIMITS 537

TABLE 207: GARDS_ROLES 538

TABLE 208: GARDS_ROLES_PERMISSIONS 539

TABLE 209: GARDS_SAMPLE_AUX 540

TABLE 210: GARDS_SAMPLE_CAT 541

xviii LIST OF TABLES

TABLE 211: GARDS_SAMPLE_CERT 542

TABLE 212: GARDS_SAMPLE_CERT_LINES 543

TABLE 213: GARDS_SAMPLE_DATA 544

TABLE 214: GARDS_SAMPLE_DESCRIPTION 546

TABLE 215: GARDS_SAMPLE_FLAGS 547

TABLE 216: GARDS_SAMPLE_PROC_PARAMS 548

TABLE 217: GARDS_SAMPLE_RATIOS 551

TABLE 218: GARDS_SAMPLE_STATUS 552

TABLE 219: GARDS_SAMPLE_UPDATE_PARAMS 553

TABLE 220: GARDS_SAMPLE_XE_PROC_PARAMS 554

TABLE 221: GARDS_SOH_CHAR_DATA 555

TABLE 222: GARDS_SOH_CODE 556

TABLE 223: GARDS_SOH_HEADER 557

TABLE 224: GARDS_SOH_NUM_DATA 558

TABLE 225: GARDS_SOH_SENSOR_DATA 559

TABLE 226: GARDS_SPECTRUM 560

TABLE 227: GARDS_STADET 561

TABLE 228: GARDS_STATION_ASSIGNMENTS 562

TABLE 229: GARDS_STATIONS 563

TABLE 230: GARDS_STATIONS_SCHEDULE 564

TABLE 231: GARDS_STATUS_HISTORY 565

TABLE 232: GARDS_TOTAL_EFFIC 566

TABLE 233: GARDS_TRENDVUE 567

TABLE 234: GARDS_UPDATE_PARAMS_TEMPLATE 568

TABLE 235: GARDS_UPDATE_REFLINES 569

TABLE 236: GARDS_USER_COMMENTS 570

TABLE 237: GARDS_USERENV 571

TABLE 238: GARDS_USERS 572

TABLE 239: GARDS_USERS_ROLES 573

TABLE 240: GARDS_XE_NUCL_LIB 574

xix LIST OF TABLES

TABLE 241: GARDS_XE_NUCL_LINES_LIB 575

TABLE 242: GARDS_XE_PROC_PARAMS_TEMPLATE 576

xx IDC DOCUMENTATION User Guides

About this Document

This chapter describes the organization and content of the document and includes the following topics:

■ Purpose

■ Scope

■ Audience

■ Related Information

■ Using this Document

Database Schema

IDC-5.1.1Rev5 October 2002 xxi IDC DOCUMENTATION User Guides

About this Document

PURPOSE

This document describes the Prototype International Data Centre (PIDC) database schema. It is Revision 5 of Database Schema.

SCOPE

This document describes the schema used in the PIDC databases. The schema includes relationships between tables, table descriptions, and definitions of the table columns.

This document does not describe the specific location and general use of these tables at the PIDC or how to manipulate them to obtain information. Nor does it provide the formats for external file representations of the tables. These topics are described in sources cited in Related Information.

AUDIENCE

This document is intended for software developers, engineers, scientists, processing operators, and anyone who needs to interact with the databases at the PIDC.

RELATED INFORMATION

This document supersedes [And90a], [Swa91], [Swa93], [Car97], [IDC5.1.1], [IDC5.1.1Rev1], and [IDC5.1.1Rev5].

External formats of all columns used with S/H/I data are described in “S/H/I Column Descriptions” on page 185, and most can also be found in [Car97].

Database Schema xxii October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

About this Document ▼

Tables used with specific application software are described in the software design documents (for example, [IDC7.1.1], [IDC7.1.3], [IDC7.1.4], [IDC7.1.5], [IDC7.1.6], [IDC7.1.10Rev3], [IDC7.1.11], [IDC7.1.12], [IDC7.3.1], [IDC7.4.1], [IDC7.4.2], [IDC7.4.3], [IDC7.4.4], and [IDC7.5.1]).

The following documents provide information and instructions for retrieving data from the PIDC databases:

■ Database Tutorial [IDC5.1.2]

■ Configuration of PIDC Databases [IDC5.1.3Rev0.1]

See “References” on page R669 for a listing of all the sources of information consulted in preparing this document.

USING THIS DOCUMENT

This document is part of the overall documentation architecture for the International Data Centre (IDC). It is part of the User Guides document category, which provides information relevant to understanding IDC processing.

This document is organized as follows:

■ Chapter 1: S/H/I Entity Relationships This chapter describes the relationships between the S/H/I database tables.

■ Chapter 2: S/H/I Table Descriptions This chapter describes each table in the S/H/I database schema (in alphabetical order). It includes information about the category to which the table belongs, the columns included in the table, ORACLE storage types for each column, keys (primary, alternate, and foreign), and column categories (descriptive, measurement, or administrative).

■ Chapter 3: S/H/I Column Descriptions This chapter provides detailed descriptions of the columns of the S/H/I database schema including the tables in which the columns may be found, a full description of the column, storage and external formats, NA values, units, and ranges.

Database Schema

IDC-5.1.1Rev5 October 2002 xxiii IDC DOCUMENTATION User Guides

▼ About this Document

■ Chapter 4: Radionuclide Database Overview This chapter provides an overview of the radionuclide database tables through an organizational description of the tables.

■ Chapter 5: Radionuclide Entity Relationships This chapter describes the relationships between the radionuclide database tables.

■ Chapter 6: Radionuclide Table Descriptions This chapter describes each table in the radionuclide database schema (in alphabetical order). It includes information about the columns included in the table, ORACLE storage types for each column, and keys (primary, alternate, and foreign).

■ Chapter 7: Radionuclide Column Descriptions This chapter provides detailed descriptions of the columns of the radionuclide database schema including the tables in which the columns may be found, a full description of the column, storage and external formats, NA values, units, and ranges.

■ References This section lists the sources cited in this document.

■ Glossary This section defines the terms, abbreviations, and acronyms used in this document.

Conventions

This document uses a variety of conventions, which are described in the following tables. Table I shows the conventions for entity-relationship diagrams. Table II lists typographical conventions. Table III explains certain technical terms that are not part of the standard Glossary, which is located at the end of this document.

Database Schema xxiv October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

About this Document ▼

TABLE I: ENTITY-RELATIONSHIP SYMBOLS

Description Symbol

One A maps to one B. AB

One A maps to zero or one B. AB

One A maps to many Bs. AB

One A maps to zero or many Bs. AB database table tablename primary key foreign key attribute 1 attribute 2 … attribute n

Database Schema

IDC-5.1.1Rev5 October 2002 xxv IDC DOCUMENTATION User Guides

▼ About this Document

TABLE II: TYPOGRAPHICAL CONVENTIONS

Element Font Example

database table bold dataready database table and column, prodtrack.status when written in the dot notation

database columns italics status processes, software units, and ParseSubs libraries user-defined arguments and delete-remarks object variables used in parameter (par) files or program command lines titles of documents BEA supplied server software Continuous Data Subsystem (all CAPS) BRIDGE

computer code and output courier >(list ‘a ‘b ‘c) filenames, directories, and web ars.scm sites text that should be typed in edit-filter-dialog exactly as shown

TABLE III:TECHNICAL TERMS

Term Description

Data: Administrative database columns used for administrative purposes

Data: Descriptive database columns that are qualitative

Data: Measurement database columns that are quantitative

field database column

Keys: Alternate set of alternate database columns that uniquely define a row in a database table (unique key)

Keys: Foreign primary key in a different table

Keys: Primary set of database columns that uniquely define a row in a database table (unique key)

Database Schema xxvi October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

About this Document ▼

Dates and Times

The time column used throughout the S/H/I schema is stored as epochal time, the number of seconds since January 1, 1970. Epochal time has a precision of one millisecond. Often time is matched by the more readable field, jdate. This “Julian date” represents a day in the form yyyyddd; for example, 1981231 where 1981 is the year (yyyy) and 231 is the day of year (ddd).

Oracle Data Types

The PIDC database uses four of the available ORACLE data types:

■ varchar2(n) All character data in the database are defined to be varchar2(n) where n is the maximum number of characters in the string. varchar2 does not store trailing blanks.

■ number(n) All integer fields in the database are defined to be number(n) where n is the maximum number of digits allowed in the field. Number may also be used without specifying the maximum number of digits.

■ float(n) ORACLE supports the float(n) data type where n is the maximum number of binary digits. Float allows the approximation of single and double precision floats commonly used in scientific programming. The decimal point may be specified anywhere from the first to the last digit (or not at all). All real numbers in the database are single precision float(24), except for epoch time fields such as time, endtime, and other time fields that are double precision float(53).

■ date The only columns in the database that are declared to be the ORACLE date data type are the lddate, moddate, last_mig_date, offdate, ondate, and initialdate columns, which store the day and time a record was inserted into the database or last modified.

Database Schema

IDC-5.1.1Rev5 October 2002 xxvii IDC DOCUMENTATION User Guides

▼ About this Document

Database Schema xxviii October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

Chapter 1: S/H/I Entity Relationships

This chapter describes the relationships between selected tables for the PIDC database schema. The following topics are covered:

■ Overview

■ Fundamental Tables

■ Reference Tables

■ S/H/I Application Software Tables

Database Schema

IDC-5.1.1Rev5 October 2002 1 IDC DOCUMENTATION User Guides

Chapter 1: S/H/I Entity Relationships

OVERVIEW

This chapter contains entity-relationship diagrams that show the relationships among database tables for the IDC database schema. The diagrams include the table names, and, in most cases, the keys as well as the names of all of the columns. The table name is always shown at the top of the table symbol. Keys (if present) are shown below the table name. The primary key of a table is indicated with a black key symbol. An optional foreign key is indicated with a white key symbol. Keys consisting of multiple columns are shown with a key symbol next to the first column of the key, and the remaining columns are listed beneath with no symbol. All column names (if present) are shown below the key section in the diagrams. Some of the key columns in the schema have been denormalized for convenience and usability. For readability, relationships for denormalized keys are not shown. Furthermore, the primary key, commid, of the table remark is not explicitly drawn in the tables in which it appears as a foreign key.

Column Relationships

Relationships between tables are usually indicated by naming the column or columns through which two tables are related. Table 1 explains the syntax used. In many cases the column names that must be compared in the two tables are not identical, or a column value in one table must be compared to more than one column value in another table. The delimiters in the syntax are the dash (-) and the slash (/). A dash (-) separates groups of column names from the two tables, and slashes (/) separate the columns that comprise the composite key. Other symbols, such as equal (=), vertical bar (|), ampersand (&), and brackets, specify how the columns are compared. Expressions within brackets in relationships between tables are evaluated first. The order of operations is: =, |, and &.

Database Schema

2 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

TABLE 1: SYNTAX USED TO INDICATE DATABASE TABLE RELATIONSHIPS

Syntax Definition

col This is the simplest case where the column names (col) of the keys in the tables at each end of the relationship are the same. Both keys consist of a single column.

col1/col2 A slash (/) is used when a key is comprised of multiple columns. Here, the keys in both tables are the same and consist of two columns, col1 and col2.

col1-col2 A dash (-) is used when the column names of the keys in the two tables are not the same. Col1 is the name of the key column in one table. Col2 is the name of the key column in the other table. Each key consists of a single column. Only one dash may be used, and the dash separates the keys of the two tables. A dash can be combined with slash (/) to show that the keys consist of multiple columns and that one or more of the columns have different names in the two tables as in col1/col2-col3/col4 (both parts of the key are different in the two tables), or col1/col2-col1/col3 (only the second part of the key is different in the two tables).

col1-col2/col3=value An equals sign (=) is used when a component of a key must be set to a particular value. Here col1 is the name of the key column in one table. Col2 and col3 are the names of the key columns in the other table, and col3 must be set to the shown value. See the arid-tagid/tagname=arid relationship between arrival and wftag and orid-tagid/tagname=orid relationship between origin and wftag.

col1-col2 | col3 A vertical line (|) is used to show that the key in a table could be one of a set of columns. This is different from a key that consists of multiple columns. Here col1 corresponds to either col2 or col3. See the magid-mbid|msid|mlid relationship between netmag and origin.

col1-col2 & col3 An ampersand (&) is used to show that a key in one table must have a value between the values of two keys in another table. Here the value of col1 must be between the values of col2 and col3. See the sta/chan/time-sta/chan/time&endtime relationship between wfdisc and sensor.

Database Schema

IDC-5.1.1Rev5 October 2002 3 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

TABLE 1: SYNTAX USED TO INDICATE DATABASE TABLE RELATIONSHIPS (CONTINUED)

Syntax Definition

(col1)-(col2) Brackets () are used to show that the keys within them have different formats and a conversion must be made to make the comparison. Here col1 corresponds to col2, but col1 and col2 have different storage formats (usually an epoch time versus a date). See the sta/chan/(time)-sta/chan/(ondate&offdate) relationship between sitechan and siteaux.

The relationship shown in Figure 1, with table_1 columns on the left and table_2 columns on the right, demonstrates the possible relationships between the columns of two different tables. The syntax of Table 1 is used to interpret the relationships between the columns of table_1 and table_2 in Figure 1. Col8 in table_2 has no matching column in table_1 and must be equal to value in this relationship. All other columns have one or more corresponding columns in the other table. Following the syntax, col1 in table_1 must have the same value as col1 in table_2, col2 in table_1 must have a value between col4 and col5 in table_2, and col3 in table_1 must match either col6 or col7 in table_2 for the one-to-many relationship indicated by the entity-relationship symbol (Table I on page xxv) to be true.

table_1 table_2 col1/col2/col3 - col1/(col4&col5)/col6|col7/col8=value col1 col1 col2 col4 col3 col5 col6 col1 col7 col2 col8 col3 … col1 col4 col5 col6 col7 col8 …

FIGURE 1. SAMPLE ENTITY RELATIONSHIP

Database Schema

4 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

Some of the entity-relationship diagrams show more than one relationship between two tables. For example, there are two relationships between the origin and event tables in Figure 2: a many-to-zero or many-to-one relationship through evid and a zero-to-one or one-to-one relationship through prefor-orid. The evid relationship states that for every origin entry, there is zero or one corresponding entry in event where the evid in origin equals the evid in event, and for every event entry, there are many origin entries where the evid in event equals the evid in origin. The prefor-orid relationship states that for every origin entry, there is zero or one corresponding entry in event where the orid in origin equals the prefor in event, and for every event entry, there is one origin entry where the prefor in event equals the orid in origin.

Table Categories

The database tables of the schema are grouped into natural categories. The first category contains the fundamental tables used with S/H/I data. These tables are used by many applications and are frequently updated. The fundamental tables contain a smaller set called the core tables. The core tables, which have remained essentially unchanged for many years, have been widely adopted by other seismological organizations, and therefore their definitions are virtually immutable. The relationships between the fundamental tables are shown in Figures 2 through 7.

Figures 8, 9, and 10 show the relationships of tables in the second category, referential tables for S/H/I data. These tables are read by many applications, but seldom if ever are the contents altered. Most of the data in these tables pertain to International Monitoring System (IMS) stations and seismic networks.

Relationships between tables used by only a few application programs are shown in 11 additional figures. These are further grouped according to the software configuration items of the software architecture. Figures 11 and 12 have tables associated with automatic processing; Figures 13, 14, and 15 have tables associated with interactive processing; and Figure 16 has tables associated with management of distributed processes. Figures 17 through 21 are related to the data services software; Figures 22 and 23 are used by system monitoring software; Figure 24 shows tables that facilitate use of the database; and finally, Figure 25 shows tables that contain information about historical explosions.

Database Schema

IDC-5.1.1Rev5 October 2002 5 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

FUNDAMENTAL TABLES

The fundamental tables have been part of seismic processing at the PIDC from its incep- tion. They hold data characterizing time-series signals as well as the collections of signals that are associated with a particular origin or event.

Figure 2 summarizes the fundamental tables. In this figure, only the table names and keys are shown. Those tables that are part of the core set are labeled 3.0 core and 3.1 core, indicating previous versions of the schema [And90a], [Swa91], [Swa93]. Figure 3 shows the tables that have data related to signal arrivals and the association of arrivals to origins and events. Additional data about signal arrivals are recorded in the tables shown in Figure 4, and Figure 5 shows tables holding data about source size.

Tables holding data used for event characterization are shown in Figure 6. Finally, Fig- ure 7 shows the relationships of tables that have information about the time-series data, which are themselves saved in conventional files.

Summary of Tables and Keys

Fundamental tables related to stored time series, detected signals, and relationships between signals and events are shown in Figure 2. This summary provides the table names, keys, and relationships, but each table is presented in its entirety in a subsequent figure.

Data from the IMS stations (wfdisc) are processed for detections (detection) from which arrivals and signal characteristics are extracted (amplitude, arrival, stassoc). The signals are used to infer event locations (assoc, event, netmag, origerr, origin, originref, parrival, stamag).

Database Schema

6 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

arid orid evid arrival assoc origin

sta arid orid time orid lat arid 3.0 core lon stassid depth chanid arid-tagid/tagname=arid time 3.0 core evid orid-tagid/tagname=orid mbid stassid msid mlid stassoc wftag 3.0 core orid stassid tagname 3.0 core tagid wfid origerr 3.0 core orid arid wfid 3.0 core detection wfdisc prefor-orid sta wfid time sta event arid chan time evid prefor 3.0 core orid 3.0 core arid magid-mbid | msid | mlid evid ampid amplitude stamag netmag

ampid magid magid magid arid ampid evid parid sta net amptype arid orid orid 3.0 core evid parid 3.1 core evid parrival originref orid parid orid sta lat time lon orid depth evid time evid mbid msid mlid

FIGURE 2. RELATIONSHIPS BETWEEN FUNDAMENTAL S/H/I TABLES

Database Schema

IDC-5.1.1Rev5 October 2002 7 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

Event

Figure 3 shows tables involved in forming origin hypotheses and events. Each table is part of the core set. Tables with information about event arrivals, location, origin time, and error are included. During automated processing, groups of arrivals from several stations are associated with presumed events. The initial origin estimate for an individual station is contained in the stassoc table, which is related to the arrival table through stassid. Specific arrivals listed in the arrival table are associated with origins in the origin table through the assoc table. An event may have several different origins, each of which is a different estimate. The preferred origin is indicated in the event table.

Measurements

The tables shown in Figures 4, 5, and 6 contain additional data about seismic and hydroacoustic signals and the magnitudes, locations, and characteristics of events. Most tables in this category lie outside the core set and are used by a smaller number of applications.

Figure 4 shows tables that have detailed data about arrivals. Figure 5 shows tables related to the location, origin time, and size of an event.

The event characterization tables in Figure 6 include spvar, complexity, splp, thirdmom, timefreq, and ceppks. The spvar table contains arrival-based information and is related to the arrival table through arid. The other tables contain origin-based measurements and are related to origin through orid.

Database Schema

8 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

arid orid evid arrival assoc origin event prefor-orid sta arid orid evid time orid lat prefor arid lon stassid arid depth evid chanid orid time evname sta evid prefor sta phase mbid auth time belief msid commid arid delta mlid lddate jdate seaz stassid esaz lat chanid timeres lon orid chan timedef depth iphase azres time stype azdef orid deltim slores evid origerr azimuth slodef jdate delaz emares nass orid slow wgt ndef delslo vmodel ndp orid ema commid grn sxx rect lddate srn syy amp etype szz per depdp stt logat stassid dtype sxy clip mb sxz fm mbid syz snr stassoc ms stx qual msid sty auth ml stassid stz commid mlid sdobs lddate algorithm stassid smajax auth sta sminax commid etype strike lddate location sdepth dist stime azimuth conf lat commid lon lddate depth time imb ims iml auth commid lddate

FIGURE 3. EVENT TABLE RELATIONSHIPS

Database Schema

IDC-5.1.1Rev5 October 2002 9 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

arrival

arid arid

arid arid amp3c infra_features apma hydro_features arid arid rid apmarid arid arid arid arid arid eng_time phase cfreq peak_time eng_dur arid vamp peak_level eng_deldur freq vsnr total_energy coh_time snr hamp mean_arrival_time coh_dur ampp hsnr time_spread coh_deldur amps htov onset_time coinc_time amplr rid termination_time coinc_dur rect lddate total_time coinc_deldur plans num_cross ford planlr ave_noise zrcr_freq hvratp arid skewness zrcr_delfreq hvrat kurtosis crnr_freq hmxmn detection cep_var_signal crnr_delfreq inang3 cep_delay_time_signal coh_per seazp sta cep_peak_std_signal coh_snr seazs time cep_var_trend total_energy seazlr arid cep_delay_time_trend auth inang1 cep_peak_std_trend commid ptime arid low_cut lddate stime jdate high_cut auth sta ford apmarid time ftype commid chan fzp lddate bmtyp prob_weight_time sproid sigma_time cfreq lddate arid seaz delaz slow hydro_arr_group hydro_assoc delslo hydro_id snr hydro_id arid stav net hydro_id fstat deltim hydro_id arid bandw az1 hydro_id fkqual az2 azcontrib commid slow lddate lddate delaz nhydarr net hyd_grp_phase lddate

FIGURE 4. DETAIL TABLES RELATED TO ARRIVAL

Database Schema

10 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

arid orid evid arrival assoc origin event prefor-orid arid orid magid-mbid | msid | mlid ampid magid amplitude stamag netmag evid

ampid magid magid arid ampid evid parid sta net amptype arid orid orid ampid evid magid arid net parid magid orid chan ampid evid originref amp sta magtype per arid nsta orid snr orid magnitude lat amptime evid uncertainty lon start_time phase auth depth duration delta commid time bandw magtype lddate evid amptype magnitude mbid units uncertainty msid clip magres mlid inarrival magdef auth mmodel orid lddate auth lat commid evid lon lddate depth parrival time orid evid parid mbid parid sta mlid amptype time msid orid ndef evid ndp ampdescript grn parid srn amptype orid etype evid depdp amptype sta dtype toff time mb tlen azimuth ms gvlo slow ml gvhi phase algorithm mtype delta auth descr vmodel commid lddate lddate lddate

FIGURE 5. MEASUREMENT TABLE RELATIONSHIPS

Database Schema

IDC-5.1.1Rev5 October 2002 11 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

arid orid arrival assoc origin

arid orid

spvar complexity splp

arid orid orid fmin sta orid sta fmax phase fsid orid orid sta arid sta rectype fsid phase ratio acoef rectype lddate bcoef complexity ccoef snr fmin lddate fmax svar lddate timefreq ceppks orid orid orid thirdmom sta orid sta ptyp arid orid arid sta orid arid rectype sta sta zavpct ptyp rectype navpct pkamp tmf eavpct pkqf tmfpct xavpct lddate lddate zavcep navcep eavcep zavcor navcor eavcor xcor lddate

FIGURE 6. EVENT CHARACTERIZATION TABLE RELATIONSHIPS

Waveforms

The waveform tables include wfdisc, wfaux, and wftag (see Figure 7). The wfdisc table is related to most other tables through the wftag table. However, sta, chan, and time are more frequently used to link the arrival and wfdisc tables directly.

Database Schema

12 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

arrival origin

wfdisc arid-tagid/tagname=arid orid-tagid/tagname=orid sta wftag chan wfid msgid-tagid/tagname=msgid time tagname wfid tagid chanid wfid msgdisc

sta tagname chan tagid time wfid wfid wfid lddate chanid jdate endtime nsamp wfaux samprate calib wfid calper instype wfid segtype length datatype clip dir dfile foff commid lddate

FIGURE 7. WAVEFORM TABLE RELATIONSHIPS

REFERENCE TABLES

The reference tables are fairly static and primarily contain look-up information. Figure 8 is an overview of the tables in this category. As with Figure 2, no column names are provided, and tables in the core set are noted. Tables shown by name only are core tables that were previously shown in Figure 2.

Network

Figure 9 shows tables related to networks, which are collections of stations across wide geographic areas. Network tables include information on the names of the networks, the stations included in them, the participation of the stations in the network, and geographic and seismic region information.

Database Schema

IDC-5.1.1Rev5 October 2002 13 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

stassid arid orid stassoc arrival assoc origin

sta srn sta grn sta net site affiliation network gregion

sta net net grn ondate sta 3.0 core 3.0 core 3.0 core 3.0 core

sta sta net

site_address participation sregion

sta net srn sta 3.0 core

sta/ondate

arid-tagid/tagname=arid wfid arid wfdisc wftag arrival amplitude

sta/chan/time- sta/chan/time- sta/chan/time&endtime sta/chan/time&endtime

sta/chan/jdate- sta/chan/ondate&offdate

sta/chan sitechan sensor inid instrument chanid sta sta inid chan chan ondate time 3.0 core chanid endtime inid 3.0 core chanid sta/chan/(time)- 3.0 core sta/chan/(ondate&offdate) siteaux

sta chan time

FIGURE 8. REFERENTIAL CORE TABLE RELATIONSHIPS

Database Schema

14 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

stassid arid orid stassoc arrival assoc origin

sta sta sta

srn grn

sta net site affiliation network gregion

sta net net grn ondate sta net grn sta net netname grname ondate sta nettype lddate offdate sta lddate auth lat commid lon net lddate elev staname statype refsta participation sregion dnorth deast net srn lddate sta srn net srname sta lddate sta begin_date end_date site_address lddate

sta

sta name locality stat_prov country lddate

FIGURE 9. NETWORK TABLE RELATIONSHIPS

Channel

Figure 10 shows tables that contain specific information about the data channels of the IMS stations. Instrument response information is identified in the instrument table. The sensor table is linked to it through inid and from there to wfdisc and amplitude through sta/chan/time. General data characteristics for any data channel are in siteaux.

Database Schema

IDC-5.1.1Rev5 October 2002 15 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

site wfdisc amplitude

sta/chan/time- sta/chan/time- sta/ondate sta/chan/time&endtime sta/chan/time&endtime sta/chan/jdate- sta/chan/ondate&offdate sta/chan/(time)- sta/chan/(ondate&offdate) sta/chan inid siteaux sitechan sensor instrument chanid sta sta sta inid chan chan chan time ondate time inid chanid endtime insname sta inid instype chan sta chanid band time chan digital nois ondate sta samprate noissd chanid chan ncalib amcor offdate time ncalper amcorsd ctype endtime dir snthrsh edepth inid dfile rely hang chanid rsptype ptmcor vang jdate lddate stmcor descrip calratio staper lddate calper auth tshift commid instant lddate lddate

FIGURE 10.CHANNEL TABLE RELATIONSHIPS

S/H/I APPLICATION SOFTWARE TABLES

The tables shown in this section are used by fewer applications than those previously described. The tables are organized by computer software configuration items (CSCIs).

Automatic Processing

The event_control table is used by the event location and magnitude programs to preserve the values of key parameters that analysts set while reviewing the bulletin (see Fig- ure 11), and it is also used in post-analysis processing. The seisgrid and seisindex hold historical seismicity data. The tables are also used by event quality control software.

Database Schema

16 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

event event_control origin arrival

evid arid-id/objtype=a orid evid orid ga_tag orid evid objtype prefer_loc orid-id/objtype=o id constrain_ot state constrain_latlon constrain_depth objtype src_dpnt_corr id loc_src_dpnt_reg state loc_sdv_screen loc_sdv_mult grdname allow_resid loc_alpha_only loc_all_stas seisgrid seisindex phase loc_dist_varwgt mindelta mag_src_dpnt_reg grdname grdname statype mag_sdv_screen icell mag_sdv_mult grdname phase mag_alpha_only grdname lat1 mindelta mag_all_stas icell lon1 maxdelta mb_min_dist magth dlat statype mb_max_dist magtype dlon timeres mmodel nevyr nlat azres cov_sm_axes lddate nlon slores cov_depth_time orderby lddate lddate lddate

FIGURE 11.RELATIONSHIPS OF TABLES USED IN AUTOMATIC PROCESSING

Event Screening Subsystem uses the tables shown in Figure 12.

Database Schema

IDC-5.1.1Rev5 October 2002 17 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

origin

orid orid orid

evsc_prod evsc_regional evsc_hydro

prodid orid orid orid sta sta chan prodid orid orid orid sta score sta cp_broad_band dscore chan snr_high_band mscore delta noise_high_band rscore pnsmax lddate hscore pnsmax_corr depth pnsmax_err deptherr pnsn moveout_pp pnlg moveout_sp pn_snr min_dt_pp sn_snr min_dt_sp lg_snr ndp_snr_pp pnsn_qual ndp_snr_sp pnlg_qual mbms lddate mbmserr mb ms producttypeevsc parrival nsta_mb nsta_ms smaj_sc producttypeorigin smin_sc attencoef strike pctoffsh attenid min_wdepth sta/delta-sta/dmin&dmax sta clrpth ratiotype consider chan lddate regcoef attenid rcoefid sta rcoeftype ratiotype chan rcoefid xcoef rcoeftype ycoef rcoefvalue zcoef ondate dmin offdate dmax lddate lddate

FIGURE 12.EVENT SCREENING TABLE RELATIONSHIPS

Database Schema

18 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

Interactive Processing

The tables in this group support the work of S/H/I data analysts, but they are not linked to any of the core tables. Figure 13 shows tables involved in scheduling the work of analysts and recording progress. Figure 14 shows tables for the Map application. The tables have information about the base maps, as well as overlays and colors.

Interactive analysis frequently includes calculation of frequency spectrums and frequency-wave number spectrums. Figure 15 shows tables that record the results of these calculations.

revaudit revtagid/revtagname=orid-orid discard evid revid origin evid revtagid1 revtagname1 evid revtagid2 reason revtagid/revtagname=arid-arid revtagname2 auth arrival lddate revid revfunction auth revtagid1 revtagid/revtagname=magid-magid scan_date revtagname1 revtagid2 stamag jdate revtagname2 netmag revstate jdate lddate scan

allocate_hour

jdate hour datadays rebdone_dataday_flag action jdate-dataday jdate dataday jdate hour jdate dataday action time state auth endtime donetime commid lddate lddate lddate

FIGURE 13.TABLES INVOLVED IN ANALYST REVIEW OF TIME-SERIES DATA

Database Schema

IDC-5.1.1Rev5 October 2002 19 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

colormapid mapid colordisc mapcolor mapdisc

colormapid mapid mapid colormapid colormapid mapid dfile mapid mapname dir colormapid dfile colormapname lddate dir lddate maptype mapfiletype projection dimx dimy reflon overlayid mapid overlaydisc mapover reflat refoffsetlon overlayid mapid refoffsetlat overlayid lonorigradians overlayid latorigradians overlayname mapid scale dfile overlaid rotation dir lddate latminor colorname latmajor lddate lonminor lonmajor bordercolor label gctp1 gctp2 gctp3 gctp4 mappoint gctp5 gctp6 lat gctp7 lon gctp8 mptype gctp9 gctp10 lat gctp11 lon gctp12 mplabel gctp13 mptype gctp14 mpdescrip gctp15 lddate lddate

FIGURE 14.MAP TABLE RELATIONSHIPS

Database Schema

20 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

arid-tagid/tagname=arid wfid fkdisc arrival wftag wfdisc

fkid arid sta/chan/time-sta/chan/time&endtime arid jdate wfid time fsid tlen afsid fsdisc fstag fsave sta fktyp fsid afsid afsid arid chanid fsid avtype maxkx wfid fstype maxsx fsrid afsid sta nx arid fsid maxky lddate sta maxsy fsid avtype ny chanid fstype cfreq wfid maxf bandw fsrid fsrid fsrecipe nf commid arid nave fkrid jdate fsrid afsid fkid time noissd datsw tlen fsrid datatype foff sta fsdesc dir dir chan taper dfile dfile fstype taperstart foff lddate maxf taperend forid nf winlen commid datatype overlap lddate dir nfft dfile smoothvalue foff response commid lddate lddate

FIGURE 15.RELATIONSHIPS AMONG TABLES USED TO RECORD SPECTRUMS OF TIME-SERIES DATA

Distributed Processing

The Distributed Processing CSCI has software that manages jobs and orchestrates the workflow. Two tables (shown in Figure 16) are used by this software as well as by some of the data services applications.

Database Schema

IDC-5.1.1Rev5 October 2002 21 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

interval timestamp

class proclass name procname time endtime procclass intvlid procname time intvlid lddate class name time endtime state moddate lddate

FIGURE 16.TABLES USED BY DISTRIBUTED PROCESSING APPLICATIONS

Data Services

The Data Services CSCI has software to receive and forward continuous time-series data, software of the Message and Subscription Subsystems, and software used to archive time-series data.

Figure 17 shows relationships between tables of the Continuous Data Subsystem. These hold data about computers from which data are provided, computers on which data are stored for processing, and computers to which data are forwarded. Tables are also used by applications that ensure the integrity and completeness of forwarded data.

Database Schema

22 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

dlid chanid alphasite dlid dlman dlfile wfconv

sta dlid dir sta address dfile chan dlid dlid dfid chanid machine chanid sta running dlid sta address connmanport chan prefdlid controlport dir chanid prefport archiveport dfile inauth dlid forwardport machine incomp time commid partition intype commid lddate dfid insamp lddate inloop outauth full outcomp archived outtype length outsamp tlen strip time commid fwsite fwfile reaptime lddate ndc sta ndc sta chan priority ndc chanid dlid ndc fwhid commid machine fwfid lddate port ndc priority sta lddate maxtime dir dfile dfilesize lddate

outage

otgid channame sitechan sta chan extern_sta sta time sta/chan-intern_sta/intern_chan extern_chan chan endtime intern_sta ondate intern_chan chanid intern_chanid otgid chanid-intern_chanid sta chan extern_sta auxid extern_chan time extern_auth endtime intern_sta status intern_chan auth intern_chanid available commid commid lddate lddate

FIGURE 17.CONTINUOUS DATA SUBSYSTEM TABLE RELATIONSHIPS

Database Schema

IDC-5.1.1Rev5 October 2002 23 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

Figure 18 shows relationships between tables of the Message Subsystem. These tables are used by applications that receive and reply to AutoDRM requests and that make requests for seismic data from stations in the auxiliary network.

msgdisc msgdatatype msgaux msgid msgid msgid msgid intid foff msgrow userid state_count msgid msgid msgdtype msgid userid msgdformat msgrow msgver status state_count msgtype foff command subtype msize sub_status extmsgid lddate lddate intid msgid intidtype msgsrc msgid itime ftpfailed idate imethod msgid isrc ftp_address msize intid/intidtype=reqid-reqid status msgid request subject numfailedattempt dir lastfailedtime dfile reqid ftp_address foff sta status mfoff chan lddate fileoff start_time filesize end_time sigtype orid verifstatus evid ftp_address commid lddate reqid sta chan ftplogin msgdest array msgid orid ftp_address msgdid evid msgid start_time ftp_address end_time username msgdid class password msgid state lddate transmeth statecount emailto complete status requestor itime modtime stime modauthor lddate lddate

FIGURE 18.MESSAGE SUBSYSTEM TABLE RELATIONSHIPS

Database Schema

24 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

Figure 19 shows tables used by the Subscription Subsystem, which notes when products are ready, maintains subscriptions, and tracks subscription processing.

prodid dataid subsuser productcriteria prodtrack dataready

userid prodid prodid dataid dataid userid prodid msgid dataid username prodname dataid tablename domain delivid msgid account status cycle_size tagname pocid cycle_time prodid tagid priority hour_to_send delivid tagid2 lddate dow_to_send dataid data_info dom_to_send msgid status userid prodtype status lddate prodsubtype lddate subs prodfmt supress_empty prodid delivid-intid msgid prodid timelastsend userid timenextsend msgdisc userid prodid lddate prodid msgid intid userid userid intid producttypeevsc fileproduct intidtype subsid prodid fpid subsname producttypeorigin typeid prodid address prodid fpid deliv_meth producttypesta typeid status dir ondate prodid dfile offdate sta fpdescription foff initialdate chan dsize lddate typeid time typeid endtime typeid sta prodtype chan name author msgdtype version msgdformat revision header_fpid obsolete lddate lddate

FIGURE 19.SUBSCRIPTION SUBSYSTEM TABLE RELATIONSHIPS

Database Schema

IDC-5.1.1Rev5 October 2002 25 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

The datauser table supports both the Message and Subscription Subsystems. The std_chanmap and exception_chanmap tables are used by the Message Subsystem (Auto- DRM) and in Performance Monitoring (stacap) to map external channel names to channel names used internally (Figure 20).

userid datauser subsuser

userid pocid std_chanmap exception_chanmap userid pocid ext_chan sta username int_chan ext_chan domain int_chan msgtype ext_chan status int_chan sta priority ondate ext_chan commid offdate int_chan emaillimit lddate ondate servicetime offdate lddate lddate

FIGURE 20.MESSAGE AND SUBSCRIPTION SUBSYSTEM SUPPORT TABLES

The tables of the data archiving subsystem contain information used by the software subsystems that migrate database tables between databases and that migrate time-series data to the mass-storage device (see Figure 21).

Database Schema

26 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

mig_date mig_rules weights

procclass task_num phase procname query_type statype src_tbl net procclass procname task_num phase last_mig_date query_type statype lddate src net src_tbl tweight dest aweight dest_tbl sweight query_seq_no ondate seq_type offdate seq_contents lddate

arch_data_type chan_groups interval

archid class class/name class name name archid time datatype class endtime table_name name intvlid primarykey sta secondkey chan merge_adjacent duration note_missing_data inwfactivity ondate ondate offdate offdate lddate lddate

FIGURE 21.DATA ARCHIVING SUBSYSTEM TABLES

System and Performance Monitoring

The tables of the System Monitoring CSCI track the state of the hardware and software as well as the quality of the scientific results. Xlogger is used to record problems discov- ered in the system. The sitepoll table is a list of auxiliary seismic stations and channels that are regularly “polled” to determine their availability. System and performance monitoring applications tables are displayed in Figure 22.

Database Schema

IDC-5.1.1Rev5 October 2002 27 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

procclass prid problemmail problem problemlog

procclass prid plid login prid prid procclass procclass plid login procname prid lddate time time endtime dir status dfile class login sitepoll descrip lddate sta login net lddate chan

sta net chan lddate

FIGURE 22.TABLES USED BY SYSTEM MONITORING APPLICATIONS

Figure 23 displays tables that hold data pertinent to monitoring scientific performance. The bull_comp table (used by an application of the same name) compares event origins first estimated by automatic analysis against origins finally accepted by analysts. In the figure, the origin table on the left exists in the database account for automatic processing, and the origin table on the right exists in the account for interactive processing. The orig- inaux table holds data that are in bulletins provided by other organizations, but do not fit elsewhere in the schema. The three tables at the bottom of the figure are used by other evaluation applications.

Database Schema

28 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

origin origin

orid-orid1 orid-orid2 orid bull_comp orid orid-eorid origaux orid1 ex_an orid2 ev_summary orid evid forid orid1 orid eorid orid2 grn event ddist refid otfixf forid ddepth epfixf eorid dtime orid nsta ddist ndef1 nearsta gap ddepth ndef2 neardist indent dtime dndef nearaz mindist did narr1 refid maxdist dnsta narr2 refdist antype dlsta dnarr refaz evidt dasta nmatch grn orid drsta ndef1arr2 nsta lddate dtsta ndef2arr1 lsta dndef asstr asta dprimp lddate rsta dsecondp tsta ddepthp orid-forid ndef qcstats rprimp adef rsecondp primp qcstatsid rdepthp ref_loc secondp sta added refid depthp chan retime refid lddate time splitev endtime multev refid sta/chan/time - kbscause refname sta/chan/time & endtime qcstatsid lddate lat sta lon wfdisc chan descrip time lddate jdate endtime dettime detendtime missing dropped nseg masked pointspike spike nconstseg const avgconstval stdconstval auth lddate

FIGURE 23.TABLES USED FOR PERFORMANCE MONITORING

Database Schema

IDC-5.1.1Rev5 October 2002 29 IDC DOCUMENTATION Chapter 1: User Guides

▼ S/H/I Entity Relationships

Database Support

Several tables facilitate use of the database (see Figure 24). The remark table holds text comments for all tables in the schema. Lastid is used by all applications that require unique values for surrogate keys. Na_value specifies not-available values for many columns of the schema.

remark lastid xtag

commid keyname thisid lineno thisname keyname commid keyvalue thisid lineno lddate thatid remark thisname lddate thatname thisdb thatdb lddate na_value

attribute

attribute na_value

FIGURE 24.TABLES USED TO SUPPORT SCHEMA

HISTORICAL DATA TABLES

Historical explosion data are kept in tables that describe the locations, times, sizes, names, and other information about the explosions.

Database Schema

30 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 1:

S/H/I Entity Relationships ▼

evid origin event orid-prefor orid-prefor orid evid explo location glossary

orid locid abbrev evid locid lat locid lon abbrev elev abbrevtype orid depth lineno evid descrip name locname dir elev sublocname dfile yield locid lddate yldmax lat medium lon moist tdepth waterdepth elev paleodepth descrip col_interval auth col_diameter commid col_depth lddate col_volume testsite expcode exptype locid auth commid lddate

FIGURE 25.TABLES USED TO DESCRIBE EXPLOSIONS

Database Schema

IDC-5.1.1Rev5 October 2002 31

IDC DOCUMENTATION User Guides

Chapter 2: S/H/I Table Descriptions

This chapter describes the tables that comprise the PIDC S/H/I Schema and defines the physical structure of each table as it exists within the ORACLE data dictionary. Brief descriptions of the columns are provided for convenience. “Chapter 3: S/H/I Column Descriptions” on page 185 contains detailed descriptions of the columns.

Database Schema

IDC-5.1.1Rev5 October 2002 33 IDC DOCUMENTATION User Guides

Chapter 2: S/H/I Table Descriptions

AFFILIATION, STANET

The affiliation table groups stations into networks. The stanet table groups array sites into an array “network.”

TABLE 2: AFFILIATION (STANET)

Column Storage Type Description

1 net varchar2(8) unique network identifier

2 sta varchar2(6) station identifier

3 lddate date load date

Category: Core, Reference Keys: Primary net/sta Data: Descriptive net, sta Administrative lddate

Database Schema

34 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

ALLOCATE_HOUR

The allocate_hour table is used by the analyst_log application to manage analyst sched- ules.

TABLE 3: ALLOCATE_HOUR

Column Storage Type Description

1 jdate number(8) Julian date

2 hour number(2) starting hour of analysis

3 action varchar2(16) analyst task

4 auth varchar2(16) name of analyst

5 commid number(8) comment identification

6 lddate date load date

Category: Interactive Processing Keys: Primary jdate/hour/action Foreign commid Data: Descriptive action, auth Measurement jdate, hour Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 35 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

ALLOW_RESID

The allow_resid table contains the allowable maximums for the absolute values of residuals for time, azimuth, and slowness. The allowed residuals are a function of phase type and station type (single station or array), and for each of these, the allowed residuals may vary for different distance ranges. A negative value for the residual indicates an arrival field that is not permitted to be defining for that phase, statype, and distance range.

TABLE 4: ALLOW_RESID

Column Storage Type Description

1 phase varchar2(8) associated phase

2 mindelta float(24) minimum station to event distance

3 maxdelta float(24) maximum station to event distance

4 statype varchar2(4) station type: single station, array

5 timeres float(24) time residual

6 azres float(24) azimuth residual

7 slores float(24) slowness residual

8 lddate date load date

Category: Automatic Processing Keys: Primary phase/mindelta/statype Data: Descriptive phase, statype Measurement mindelta, maxdelta, timeres, azres, slores Administrative lddate

Database Schema

36 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

ALPHASITE

The alphasite table is used for tracking continuous data connections by the DLMan application. For a given station, there must be a row in the table for each address from which the station may send continuous data. Prefdlid and prefport describe the preferred DLMan connection for the station. DLMan fills in dlid and time while a station is actively connected. Dlid indicates to which dlid the station is currently connected (may be different from prefdlid), and time is the system time for the last activity on the station’s connection (not the time of any data received). For stations that are not connected, time and dlid are zero (0).

TABLE 5: ALPHASITE

Column Storage Type Description

1 sta varchar2(6) station code

2 address varchar2(16) source internet address

3 prefdlid number(8) dlid for preferred DLMan

4 prefport number(6) preferred network port

5 dlid number(8) dlid handling station

6 time float(53) clock time of most recent activity

7 commid number(8) comment identifier

8 lddate date load date

Category: Data Services Keys: Primary sta/address Foreign dlid, commid Data: Descriptive sta, address, prefdlid, prefport, dlid Measurement time Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 37 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

AMP3C

The amp3c table contains amplitude measurements made on three-component data for a specific detection.

TABLE 6: AMP3C

Column Storage Type Description

1 arid number(8) arrival identifier

2 cfreq float(24) center frequency of filter band amplitude is measured on

3 vamp float(24) vertical amplitude

4 vsnr float(24) vertical signal-to-noise ratio

5 hamp float(24) horizontal amplitude

6 hsnr float(24) horizontal signal-to-noise ratio

7 htov float(24) horizontal to vertical amplitude ratio

8 rid varchar2(8) recipe identifier

9 lddate date load date

Category: Fundamental Keys: Primary arid/rid Data: Descriptive rid Measurement cfreq, vamp, vsnr, hamp, hsnr, htov Administrative lddate

Database Schema

38 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

AMPDESCRIPT

The ampdescript table contains descriptions of how amplitude measurements in amplitude were made.

TABLE 7: AMPDESCRIPT

Column Storage Type Description

1 amptime varchar2(8) amplitude measure descriptor

2 toff float(24) offset from theoretical or observed arrival time

3 tlen float(24) duration of measurement window

4 gvlo float(24) low group velocity for measurement window (km/sec)

5 gvhi float(24) high group velocity for measurement window (km/sec)

6 mtype varchar2(8) measurement type

7 descr varchar2(255) description

8 lddate date load date

Category: Fundamental Keys: Primary amptype Data: Descriptive amptype, mtype, descr Measurement toff, tlen, gvlo, gvhi Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 39 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

AMPLITUDE

The amplitude table contains arrival-based and origin-based amplitude measurements. The amplitude measurement is described in ampdescript.

TABLE 8: AMPLITUDE

Column Storage Type Description

1 ampid number(8) amplitude identifier

2 arid number(8) arrival identifier

3 parid number(8) predicted arrival identifier

4 chan varchar2(8) channel code

5 amp float(24) amplitude (nm)

6 per float(24) period (s)

7 snr float(24) signal-to-noise ratio

8 amptime float(53) time of amplitude measure

9 start_time float(53) start time of measurement window

10 duration float(24) duration of measurement window

11 bandw float(24) bandwidth

12 amptype varchar2(8) amplitude measure descriptor

13 units varchar2(15) units

14 clip varchar2(1) clipped flag

15 inarrival varchar2(1) “y” or “n” flag indicating if amp is the same as the amp in the arrival table

16 auth varchar2(15) author

17 lddate date load date

Database Schema

40 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

Category: Fundamental Keys: Primary ampid Foreign arid, parid, amptype Data: Descriptive chan, amptype, units, inarrival Measurement amp, per, snr, amptime, start_time, duration, bandw, clip Administrative auth, lddate

Database Schema

IDC-5.1.1Rev5 October 2002 41 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

APMA

The apma table contains results of particle motion analysis for a specific detection.

TABLE 9: APMA

Column Storage Type Description

1 phase varchar2(8) phase

2 arid number(8) arrival identifier

3 freq float(24) frequency

4 snr float(24) signal-to-noise ratio

5 ampp float(24) P-phase amplitude

6 amps float(24) S-phase amplitude

7 amplr float(24) Rayleigh-phase amplitude

8 rect float(24) rectilinearity

9 plans float(24) S-phase planarity

10 planlr float(24) Rayleigh-phase planarity

11 hvratp float(24) P-phase horizontal-to-vertical ratio

12 hvrat float(24) S-phase horizontal-to-vertical ratio

13 hmxmn float(24) maximum-to-minimum horizontal ratio

14 inang3 float(24) short-axis incidence angle

15 seazp float(24) P-phase observed azimuth

16 seazs float(24) S-phase observed azimuth

17 seazlr float(24) Rayleigh-phase observed azimuth

18 inang1 float(24) long-axis incidence angle

19 ptime float(53) P-phase extraction time

20 stime float(53) S-phase extraction time

21 auth varchar2(15) author

Database Schema

42 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

TABLE 9: APMA (CONTINUED)

Column Storage Type Description

22 apmarid number(8) apma recipe identifier

23 commid number(8) comment identifier

24 lddate date load date

Category: Fundamental Keys: Primary apmarid Foreign arid, commid Data: Descriptive phase Measurement freq, snr, ampp, amps, amplr, rect, plans, planlr, hvratp, hvrat, hmxmn, inang3, seazp, seazs, seazlr, inang1, ptime, stime Administrative auth, lddate

Database Schema

IDC-5.1.1Rev5 October 2002 43 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

ARCH_DATA_TYPE

The arch_data_type table contains information used by the archiving software.

TABLE 10: ARCH_DATA_TYPE

Column Storage Type Description

1 archid number(8) Archive row identifier

2 datatype varchar2(24) data type (or class of data)

3 table_name varchar2(32) name of the table encapsulating the data type

4 primarykey varchar2(24) not used

5 secondkey varchar2(24) not used

6 merge_adjacent varchar2(2) y indicates Archive should merge adjacent rows

7 note_missing_data varchar2(2) indicates that this data type is for late arriving data

8 ondate number(8) first date this row is valid

9 offdate number(8) last date this row is valid

10 lddate date load date

Category: Core, Fundamental Keys: Primary archid Data: Descriptive datatype, table_name, primarykey, secondkey, merge_adjacent, not_missing_data, ondate, offdate Administrative lddate

Database Schema

44 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

ARRIVAL

The arrival table contains summary information about arrivals.

TABLE 11: ARRIVAL

Column Storage Type Description

1 sta varchar2(6) station code

2 time float(53) epoch time

3 arid number(8) arrival identifier

4 jdate number(8) Julian date

5 stassid number(8) stassoc identifier

6 chanid number(8) instrument identifier

7 chan varchar2(8) channel code

8 iphase varchar2(8) reported phase

9 stype varchar2(1) signal type

10 deltim float(24) time uncertainty

11 azimuth float(24) observed azimuth

12 delaz float(24) azimuth uncertainty

13 slow float(24) observed slowness, seconds/degree

14 delslo float(24) slowness uncertainty

15 ema float(24) emergence angle

16 rect float(24) rectilinearity

17 amp float(24) amplitude, instrument corrected, nm

18 per float(24) period

19 logat float(24) log(amp/per)

20 clip varchar2(1) clipped flag

21 fm varchar2(2) first motion

22 snr float(24) signal-to-noise ratio

Database Schema

IDC-5.1.1Rev5 October 2002 45 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

TABLE 11: ARRIVAL (CONTINUED)

Column Storage Type Description

23 qual varchar2(1) signal onset quality

24 auth varchar2(15) author

25 commid number(8) comment identifier

26 lddate date load date

Category: Core, Fundamental Keys: Primary sta/time Alternate arid Foreign stassid, chanid, commid Data: Descriptive sta, chan, iphase, stype Measurement time, jdate, deltim, azimuth, delaz, slow, delslo, ema, rect, amp, per, logat, clip, fm, snr, qual Administrative auth, lddate

Database Schema

46 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

ASSOC, ASSOC_TEMP_GA

The assoc table contains information that connects arrivals (entries in the arrival table) to a particular origin. The assoc_temp_ga table is used by the Global Association (GA) application to store temporary associations.

TABLE 12: ASSOC (ASSOC_TEMP_GA)

Column Storage Type Description

1 arid number(8) arrival identifier

2 orid number(8) origin identifier

3 sta varchar2(6) station code

4 phase varchar2(8) associated phase

5 belief float(24) phase confidence

6 delta float(24) station-to-event distance

7 seaz float(24) station-to-event azimuth

8 esaz float(24) event-to-station azimuth

9 timeres float(24) time residual

10 timedef varchar2(1) time = defining (d), nondefining (n)

11 azres float(24) azimuth residual

12 azdef varchar2(1) azimuth = defining (d), nondefining (n)

13 slores float(24) slowness residual

14 slodef varchar2(1) slowness = defining (d), nondefining (n)

15 emares float(24) incidence angle residual

16 wgt float(24) location weight

17 vmodel varchar2(15) velocity model

18 commid number(8) comment identifier

19 lddate date load date

Database Schema

IDC-5.1.1Rev5 October 2002 47 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

Category: Core, Fundamental Keys: Primary arid/orid Foreign commid Data: Descriptive sta, phase, belief, wgt, vmodel Measurement delta, seaz, esaz, timeres, timedef, azres, azdef, slores, slodef, emares Administrative lddate

Database Schema

48 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

ATTENCOEF

The attencoef table contains station-specific attenuation corrections for regional analysis.

TABLE 13: ATTENCOEF

Column Storage Type Description

1 attenid varchar2(20) attenuation coefficient set identifier

2 sta varchar2(6) station code

3 ratiotype varchar2(6) amplitude ratio identifier

4 chan varchar2(8) channel code

5 xcoef float(24) constant coefficient

6 ycoef float(24) geometrical spreading coefficient

7 zcoef float(24) attenuation coefficient

8 dmin float(24) minimum distance of applicability

9 dmax float(24) maximum distance of applicability

10 lddate date load date

Category: Fundamental Keys: Primary attenid/sta/ratiotype/chan Data: Measurement xcoef, ycoef, zcoef, dmin, dmax Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 49 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

BEAMAUX

The beamaux table is a view into the sensor and instrument tables.

TABLE 14: BEAMAUX

Column Storage Type Description

1 sta varchar2(6) station code

2 chan varchar2(8) channel code

3 ncalib float(24) nominal calibration

4 ncalper float(24) nominal calibration period

5 time float(53) epoch time of beginning of beam

6 endtime float(53) epoch time of end of beam

Category: Data Services Keys: Primary sta/chan/time Data: Descriptive sta, chan, ncalib, ncalper Measurement time, endtime

Database Schema

50 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

BULL_COMP

The bull_comp table contains results from the BullComp application of the comparison of two seismic bulletins. The information summarizes the differences between event solutions that share common associated arrivals, or (if no arrival information is available) whose locations and time uncertainties overlap.

TABLE 15: BULL_COMP

Column Storage Type Description

1 orid1 number(8) origin identifier from bulletin 1

2 orid2 number(8) origin identifier from bulletin 2

3 ddist float(24) difference in distance

4 ddepth float(24) difference in depth

5 dtime float(24) difference in epoch time

6 ndef1 number(8) number of time-defining phases for orid1

7 ndef2 number(8) number of time-defining phases for orid2

8 dndef number(8) difference in number of time-defining phases

9 narr1 number(8) number of associated arrivals for orid1

10 narr2 number(8) number of associated arrivals for orid2

11 dnarr number(8) difference in number of associated arrivals

12 nmatch number(8) number of matching arrivals (defining/ nondefining)

13 ndef1arr2 number(8) number of defining arrivals for orid1 that are arrivals (either defining or nondefining) for orid2

14 ndef2arr1 number(8) number of defining arrivals for orid2 that are arrivals (defining/ nondefining) for orid1

15 asstr varchar2(1) association strength (s or w)

16 lddate date load date

Database Schema

IDC-5.1.1Rev5 October 2002 51 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

Category: System Monitoring Keys: Primary orid1/orid2 Data: Descriptive asstr Measurement ddist, ddepth, dtime, ndef1, ndef2, dndef, narr1, narr2, dnarr, nmatch, ndef1arr2, ndef2arr1 Administrative lddate

Database Schema

52 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

CEPPKS

The ceppks table contains results of cepstral analysis and includes the amplitude and frequency of cepstral peaks that are consistent among multiple phases associated with the same event.

TABLE 16: CEPPKS

Column Storage Type Description

1 orid number(8) origin identifier

2 sta varchar2(6) station code

3 ptyp varchar2(6) consistent peak type code

4 pkamp float(24) consistent peak amplitude

5 pkqf float(24) consistent peak quefrency

6 lddate date load date

Category: Fundamental Keys: Primary orid/sta/ptyp Data: Descriptive sta, ptyp Measurement pkamp, pkqf Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 53 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

CHAN_GROUPS

The chan_groups table contains information used by the archiving software.

TABLE 17: CHAN_GROUPS

Column Storage Type Description

1 class varchar2(16) class (or data type)

2 name varchar2(16) name of the grouping

3 sta varchar2(6) station name

4 chan varchar2(8) channel name

5 duration number not used

6 inwfactivity number(1) not used

7 ondate number(8) first date this row is valid

8 offdate number(8) last date this row is valid

9 lddate date load date

Category: Data Services Keys: Primary class/name Data: Descriptive sta, chan, duration, inwfactivity, ondate, offdate Administrative lddate

Database Schema

54 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

CHANNAME

The channame table provides mapping between channel and station names.

TABLE 18: CHANNAME

Column Storage Type Description

1 extern_sta varchar2(6) external station name

2 extern_chan varchar2(8) external channel name

3 extern_auth varchar2(20) external authority using this name

4 intern_sta varchar2(6) internal station name

5 intern_chan varchar2(8) internal channel name

6 intern_chanid number(8) internal channel ID

7 commid number(8) comment identifier

8 lddate date load date

Category: Data Services Keys: Primary: extern_sta/extern_chan Foreign: intern_sta/intern_chan, intern_chanid, commid Data: Descriptive: extern_sta, extern_chan, intern_sta, intern_chan, intern_chanid Administrative: lddate

Database Schema

IDC-5.1.1Rev5 October 2002 55 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

COLORDISC

The colordisc table links a unique colormapid to a colormap name and disk file.

TABLE 19: COLORDISC

Column Storage Type Description

1 colormapid number(8) colormap identifier

2 dfile varchar2(32) data filename

3 dir varchar2(64) directory

4 colormapname varchar2(64) colormap name

5 lddate date load date

Category: Interactive Processing Keys: Primary colormapid Data: Descriptive colormapname, dfile, dir Administrative lddate

Database Schema

56 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

COMPLEXITY

The complexity table contains the complexity event characterization parameter estimated by the Detection and Feature Extraction (DFX) application.

TABLE 20: COMPLEXITY

Column Storage Type Description

1 orid number(8) origin identifier

2 sta varchar2(6) station name

3 phase varchar2(6) phase name

4 rectype varchar2(8) recipe type

5 complexity float(24) complexity measure

6 snr float(24) signal-to-noise ratio

7 lddate date load date

Category: Fundamental Keys: Primary orid/sta/phase Data: Descriptive sta, phase, rectype Measurement complexity, snr Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 57 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

DATADAYS

The datadays table contains the days and times for which analysis has been completed.

TABLE 21: DATADAYS

Column Storage Type Description

1 jdate number(8) Julian date

2 time float(53) epoch time of start of dataday

3 endtime float(53) epoch time of end of dataday

4 lddate date load date

Category: Interactive Processing Keys: Primary jdate Data: Measurement jdate, time, endtime Administrative lddate

Database Schema

58 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

DATAREADY

The dataready table indicates which data are ready to be processed by the Subscription Subsystem. Entries to the table are made by scripts running in the operational systems that process the data.

TABLE 22: DATAREADY

Column Storage Type Description

1 dataid number(8) data ready identifier

2 tablename varchar2(24) name of table

3 account varchar2(24) account name

4 tagname varchar2(12) name of reference field (for example, orid)

5 tagid number(10) value of tag name

6 tagid2 number(10) secondary tag value

7 data_info varchar2(24) miscellaneous data information

8 status varchar2(8) status of new entry (i=insert, c=change, d=delete)

9 lddate date load date

Category: Data Services Keys: Primary dataid Data: Descriptive tablename, account, tagname, data_info, status Measurement tagid, tagid2 Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 59 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

DATAUSER

The datauser table tracks authorized users of the Message and Subscription Subsystems. Each user is identified by a (unique) username and domain, which must match all email headers. The priority column specifies the class of user, and servicetime is the last time a request from the user was processed. Priority and servicetime are considered when select- ing the order in which requests will be processed. The status can either be active or inactive.

TABLE 23: DATAUSER

Column Storage Type Description

1 userid number(8) identifier for the user

2 pocid number(8) point of contact identifier

3 username varchar2(24) user name from the incoming subscription message

4 domain varchar2(48) domain name from the incoming subscription message

5 msgtype varchar2(16) message type

6 status varchar2(24) status of this user

7 priority number(2) user’s priority

8 commid number(8) comment identifier

9 emaillimit number(8) maximum size of message (in bytes) that will be delivered via email

10 servicetime float(53) last time a request from that user was ser- viced

11 lddate date load date

Database Schema

60 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

Category: Data Services Keys: Primary userid Foreign pocid, commid Data: Descriptive username, domain, msgtype, emaillimit Measurement status, priority, servicetime Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 61 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

DETECTION

The detection table contains summary information about S/H/I detections.

TABLE 24: DETECTION

Column Storage Type Description

1 arid number(8) arrival identifier

2 jdate number(8) Julian date

3 time float(53) epoch time

4 sta varchar2(6) station code

5 chan varchar2(8) channel code

6 bmtyp varchar2(4) beam type

7 sproid number(8) signal processor identifier

8 cfreq float(24) center frequency

9 seaz float(24) observed azimuth

10 delaz float(24) azimuth uncertainty

11 slow float(24) observed slowness, sec/km

12 delslo float(24) slowness uncertainty

13 snr float(24) signal-to-noise ratio

14 stav float(24) short-term average

15 fstat float(24) f-statistic

16 deltim float(24) time uncertainty

17 bandw float(24) bandwidth

18 fkqual number(4) f-k quality

19 commid number(8) comment identifier

20 lddate date load date

Database Schema

62 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

Category: Fundamental Keys: Primary sta/time Alternate arid Foreign commid Data: Descriptive sta, chan, bmtyp, sproid Measurement jdate, time, cfreq, seaz, delaz, slow, delslo, snr, stav, fstat, deltim, bandw, fkqual Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 63 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

DISCARD

The discard table contains the reason why an analyst discarded an event that was hypothesized by the automated system.

TABLE 25: DISCARD

Column Storage Type Description

1 evid number(8) event identifier

2 reason varchar2(30) reason event was discarded

3 auth varchar2(15) source/originator

4 lddate date load date

Category: Interactive Processing Keys: Primary evid Data: Descriptive reason, auth Administrative lddate

Database Schema

64 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

DLFILE

The dlfile table describes the files used in the diskloops managed by the DLMan application.

TABLE 26: DLFILE

Column Storage Type Description

1 dir varchar2(64) directory name

2 dfile varchar2(32) filename

3 machine varchar2(32) machine name

4 partition varchar2(64) disk partition name

5 dfid number(8) diskloop file identifier

6 inloop varchar2(1) file is part of a diskloop = y/n

7 full varchar2(1) file is full = y/n

8 archived varchar2(1) file is archived = y/n/a

9 length number(10) length of file, bytes

10 tlen float(24) length of file, seconds

11 time float(53) start time

12 reaptime float(53) clock time for expiration

13 sta varchar2(6) station name

14 chan varchar2(8) channel name

15 chanid number(8) channel identifier

16 dlid number(8) diskloop manager identifier

17 commid number(8) comment identifier

18 lddate date load date

Database Schema

IDC-5.1.1Rev5 October 2002 65 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

Category: Data Services Keys: Primary dir/dfile Alternate dfid Foreign chanid, dlid, commid Data: Descriptive dir, dfile, machine, partition, inloop, full, archived, length, tlen, time, sta, chan Administrative reaptime, lddate

Database Schema

66 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

DLMAN

The dlman table keeps track of currently running DLMan instances. Machine is the host on which this dlid runs (it may not run elsewhere). “Running” indicates whether that DLMan is currently operational. The table also provides the ports this dlid is currently using to listen to other processes.

TABLE 27: DLMAN

Column Storage Type Description

1 dlid number(8) diskloop manager identifier

2 machine varchar2(32) machine name

3 running varchar2(1) DLMan running = y/n

4 connmanport number(6) ConnMan port

5 controlport number(6) DataControl port

6 archiveport number(6) Archiver port

7 forwardport number(6) Forwarder port

8 commid number(8) comment identifier

9 lddate date load date

Category: Data Services Keys: Primary dlid Foreign commid Data: Descriptive machine, running, connmanport, controlport, archiveport, forwardport Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 67 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

EV_SUMMARY, EX_SUMMARY, AN_SUMMARY

The ev_summary, ex_summary, and an_summary tables contain statistical summary analysis of expert system solutions from the ExAnComp application.

TABLE 28: EV_SUMMARY (EX_SUMMARY, AN_SUMMARY)

Column Storage Type Description

1 orid number(8) origin identifier of analyst event

2 nearsta varchar2(6) code for nearest station

3 neardist float(24) distance to closest station

4 nearaz float(24) azimuth from nearest station

5 refid number(8) identifier of nearest reference point

6 refdist float(24) distance to nearest reference point

7 refaz float(24) azimuth to nearest reference point

8 grn number(8) geographic region number

9 nsta number(8) number of recording stations

10 lsta number(8) number of local observations

11 asta number(8) number of regional array observations

12 rsta number(8) number of non-array regional observations

13 tsta number(8) number of teleseismic observations

14 ndef number(8) number of time-defining phases

15 adef number(8) number of associated nondefining phases

16 primp number(8) number of primary time-defining phases used for location

17 secondp number(8) number of secondary phases used for location

18 depthp number(8) number of depth phases

19 lddate date load date

Database Schema

68 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

Category: System Monitoring Keys: Primary orid Foreign grn, refid Data: Descriptive nearsta, grn Measurement neardist, nearaz, refdist, refaz, nsta, lsta, asta, rsta, tsta, ndef, adef, primp, secondp, depthp Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 69 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

EVENT

The event table contains a list of events. Multiple origins may be defined for any one event. Prefor points to the preferred origin.

TABLE 29: EVENT

Column Storage Type Description

1 evid number(8) event identifier

2 evname varchar2(15) event name

3 prefor number(8) preferred origin

4 auth varchar2(15) source/originator

5 commid number(8) comment identifier

6 lddate date load date

Category: Core, Fundamental Keys: Primary evid Foreign prefor, commid Data: Descriptive evname, prefor Administrative auth, lddate

Database Schema

70 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

EVENT_CONTROL, IN_EVENT_CONTROL

The event_control and in_event_control tables contain event location and magnitude control parameters. This information acts as an archive of the specific user-defined controls that were used to determine the location and magnitude of a given orid. The table also includes two measurement columns (cov_sm_axes and cov_depth_time) that allow the coverage ellipse to be determined from the confidence ellipse axes.

TABLE 30: EVENT_CONTROL (IN_EVENT_CONTROL)

Column Storage Type Description

1 orid number(8) origin identification

2 evid number(8) event identification

3 prefer_loc varchar2(1) preferred location identifier (S, F, R)

4 constrain_ot number(1) flag to constrain origin time

5 constrain_latlon number(1) flag to constrain latitude/longitude

6 constrain_depth number(1) flag to constrain depth

7 src_dpnt_corr number(2) source-dependent correction code

8 loc_src_dpnt_reg varchar2(15) region name of source-dependent location correction

9 loc_sdv_screen number(1) flag to ignore large data residuals in location

10 loc_sdv_mult float(24) location large residual multiplier factor

11 loc_alpha_only number(1) flag to use only primary stations in location

12 loc_all_stas number(1) flag to use only stations with src_dpnt_corr

13 loc_dist_varwgt number(1) flag to use distance variance weighting

14 mag_src_dpnt_reg varchar2(15) region name of source-dependent magnitude correction

Database Schema

IDC-5.1.1Rev5 October 2002 71 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

TABLE 30: EVENT_CONTROL (IN_EVENT_CONTROL) (CONTINUED)

Column Storage Type Description

15 mag_sdv_screen number(1) flag to ignore large magnitude data residuals

16 mag_sdv_mult float(24) magnitude large residual multiplier factor

17 mag_alpha_only number(1) flag to limit station net used in magnitude

18 mag_all_stas number(1) flag to use only primary stations in magnitude

19 mb_min_dist float(24) minimum distance (degrees) for mb

20 mb_max_dist float(24) maximum distance (degrees) for mb 21 mmodel varchar2(15) network magnitude model

22 cov_sm_axes float(24) coverage ellipse semi-axes conversion factor

23 cov_depth_time float(24) coverage ellipse depth/time conversion factor

24 lddate date load date

Category: Automatic Processing Keys: Primary evid/orid Data: Descriptive prefer_loc, constrain_ot, constrain_latlon, constrain_depth, src_dpnt_corr, loc_src_dpnt_reg, loc_sdv_screen, loc_sdv_mult, loc_alpha_only, loc_all_stas, loc_dist_varwgt, mag_src_dpnt_reg, mag_sdv_screen, mag_sdv_mult, mag_alpha_only, mag_all_stas, mb_min_dist, mb_max_dist, mmodel Measurement cov_sm_axes, cov_depth_time Administrative lddate

Database Schema

72 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

EVSC_HYDRO

The evsc_hydro table contains station-specific hydroacoustic event-screening results for the standard and subscription criteria. One record per orid per sta is in the table.

TABLE 31: EVSC_HYDRO

Column Storage Type Description

1 orid number(8) origin identifier

2 sta varchar2(6) station code

3 cp_broad_band float(24) hydroacoustic cepstral peak amplitude in 2–80 Hz band

4 snr_high_band float(24) hydroacoustic signal-to-noise ratio in 32–64 Hz band

5 noise_high_band float(24) hydroacoustic noise level in 32–64 Hz band

6 lddate date load date

Category: Automatic Processing Keys: Primary orid/sta Data: Measurement cp_broad_band, snr_high_band, noise_high_band Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 73 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

EVSC_PROD

The evsc_prod table contains event screening results for the standard and subscription criteria. One record per orid is in the table for each subscription (prodid).

TABLE 32: EVSC_PROD

Column Storage Type Description

1 prodid number(8) product identifier

2 orid number(8) origin identifier

3 score float(24) composite screening score

4 dscore float(24) depth screening score

5 mscore float(24) mb minus Ms screening score 6 rscore float(24) regional P/S screening score

7 hscore float(24) hydroacoustic screening score

8 depth float(24) depth estimate

9 deptherr float(24) depth confidence interval

10 moveout_pp float(24) moveout of pP–P travel times

11 moveout_sp float(24) moveout of sP–P travel times

12 min_dt_pp float(24) pP–P travel time difference at nearest station beyond 25 deg.

13 min_dt_sp float(24) sP–P travel time difference at nearest station beyond 25 deg.

14 ndp_snr_pp number(8) number of pP phases with sufficient snr for moveout processing

15 ndp_snr_sp number(8) number of sP phases with sufficient snr for moveout processing

16 mbms float(24) mb minus Ms (including slope term)

17 mbmserr float(24) mb minus Ms confidence interval

18 mb float(24) mb magnitude used for event screening

19 ms float(24) Ms magnitude used for event screening

Database Schema

74 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

TABLE 32: EVSC_PROD (CONTINUED)

Column Storage Type Description

20 nsta_mb number(8) number of stations used in network mb estimate

21 nsta_ms number(8) number of stations used in network Ms estimate 22 smaj_sc float(24) scaled semi-major axis of location error ellipse

23 smin_sc float(24) scaled semi-minor axis of location error ellipse

24 strike float(24) strike angle of location error ellipse

25 pctoffsh float(24) percent of location error ellipse that is offshore

26 min_wdepth float(24) minimum water depth within location error ellipse

27 clrpth number(1) indicator of clear path to at least one hydroacoustic station

28 consider number(1) considered for event screening flag

29 lddate date load date

Category: Fundamental Keys: Primary prodid/orid Data: Descriptive consider Convenience mb, ms, strike, depth, nsta_mb, nsta_ms Measurement score, dscore, mscore, rscore, hscore, deptherr, moveout_pp, moveout_sp, min_dt_pp, min_dt_sp, ndp_snr_pp, ndp_snr_sp, mbms, mbmserr, smaj_sc, smin_sc, pctoffsh, min_wdepth, clrpth Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 75 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

EVSC_REGIONAL

The evsc_regional table contains station-specific regional seismic phase amplitude measurements and quality flags for the standard and subscription criteria. One record per orid per sta is in the table.

TABLE 33: EVSC_REGIONAL

Column Storage Type Description

1 orid number(8) origin identifier

2 sta varchar2(6) station name

3 chan varchar2(8) channel identifier

4 delta float(24) source-receiver distance

5 pnsmax float(24) maximum of Pn/Sn and Pn/Lg

6 pnsmax_corr float(24) amplitude ratio correction term

7 pnsmax_err float(24) amplitude ratio error term

8 pnsn float(24) Pn/Sn amplitude ratio

9 pnlg float(24) Pn/Lg amplitude ratio

10 pn_snr float(24) Pn amplitude snr ratio

11 sn_snr float(24) Sn amplitude snr ratio

12 lg_snr float(24) Lg amplitude snr ratio

13 pnsn_qual varchar2(10) Pn/Sn amplitude ratio quality flags

14 pnlg_qual varchar2(10) Pn/Lg amplitude ratio quality flags

15 lddate date load date

Database Schema

76 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

Category: Fundamental Keys: Primary orid/sta/chan Data: Descriptive pnsn_qual, pnlg_qual Convenience delta Measurement pnsmax, pnsmax_corr, pnsmax_err, pnsn, pnlg, pn_snr, sn_snr, lg_snr Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 77 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

EX_AN

The ex_an table contains analyses of expert system solutions compared to analyst solutions from the ExAnComp application.

TABLE 34: EX_AN

Column Storage Type Description

1 forid number(8) final origin identifier

2 eorid number(8) expert system origin identifier

3 ddist float(24) distance between forid and eorid

4 ddepth float(24) depth difference

5 dtime float(24) origin time difference

6 did varchar2(4) identification difference

7 dnsta number(8) difference in recording stations

8 dlsta number(8) difference in local stations

9 dasta number(8) difference in regional array stations

10 drsta number(8) difference in non-array regional station

11 dtsta number(8) difference in teleseismic station

12 dndef number(8) difference in defining phases

13 dprimp number(8) difference in primary phases

14 dsecondp number(8) difference in secondary phases

15 ddepthp number(8) difference in depth phases

16 rprimp number(8) renamed primary phases

17 rsecondp number(8) renamed secondary phases

18 rdepthp number(8) renamed depth phases

19 added number(8) number of added phases

20 retime number(8) number of retimed phases

21 splitev varchar2(4) split event (y/n)

Database Schema

78 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

TABLE 34: EX_AN (CONTINUED)

Column Storage Type Description

22 multev varchar2(4) multiple events (y/n)

23 kbscause varchar2(7) knowledge system explanation

24 lddate date load date

Category: System Monitoring Keys: Primary forid Foreign eorid Data: Measurement ddist, ddepth, dtime, did, dnsta, dlsta, dasta, drsta, dtsta, dndef, dprimp, dsecondp, ddepthp, rprimp, rsecondp, rdepthp, added, retime, splitev, multev, kbscause Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 79 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

EXCEPTION_CHANMAP

The exception_chanmap table contains exception channel mappings for specific stations.

TABLE 35: EXCEPTION_CHANMAP

Column Storage Type Description

1 sta varchar2(6) station code

2 ext_chan varchar2(8) external channel name

3 int_chan varchar2(8) internal channel name

4 ondate number(8) Julian start date

5 offdate number(8) Julian off date

6 lddate date load date

Category: Data Services Keys: Primary. sta, ext_chan Foreign. int_chan Data: Descriptive sta, ext_chan, int_chan Measurement ondate, offdate Administrative lddate

Database Schema

80 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

EXPLO

The explo table contains information on explosions.

TABLE 36: EXPLO

Column Storage Type Description

1 orid number(8) origin identifier

2 evid number(8) event identifier

3 name varchar2(32) shot name

4 elev float(24) surface elevation (km)

5 yield float(24) yield (kT)

6 yldmax float(24) upper limit of yield range

7 medium varchar2(48) shot medium

8 moist float(24) moisture content

9 waterdepth float(24) depth of static water table (km)

10 paleodepth float(24) depth of Paleozoic layer (km)

11 col_interval float(24) collapse interval (seconds)

12 col_diameter float(24) collapse diameter (km)

13 col_depth float(24) collapse depth (km)

14 col_volume float(24) collapse volume (km3)

15 testsite varchar2(15) test site name

16 expcode varchar2(10) explosion type code

17 exptype varchar2(15) explosion type

18 locid varchar2(30) location identification code

19 auth varchar2(15) author

20 commid number(8) comment identifier

21 lddate date load date

Database Schema

IDC-5.1.1Rev5 October 2002 81 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

Category: Historical Keys: Primary orid Foreign evid, locid, commid Data: Descriptive name, medium, testsite, expcode, exptype Measurement elev, yield, yldmax, moist, waterdepth, paleodepth, col_interval, col_diameter, col_depth, col_volume Administrative auth, lddate

Database Schema

82 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

FILEPRODUCT, FS_STAGEPRODUCT

The fileproduct table contains descriptions of files containing products.

TABLE 37: FILEPRODUCT (FS_STAGEPRODUCT)

Column Storage Type Description

1 fpid number(8) file product identifier

2 typeid number(8) identifier for the product type

3 dir varchar2(64) directory where the file is stored

4 dfile varchar2(32) filename containing the file product

5 foff number(10) file offset (in bytes) where the data begins

6 dsize number(10) size of the data (in bytes)

7 time float(53) beginning time of the data

8 endtime float(53) end time of the data

9 sta varchar2(6) station code

10 chan varchar2(8) channel code

11 author varchar2(16) author of the file product

12 version float(53) version of the author

13 revision number(4) revision number of the file product

14 obsolete number(1) flag to indicate if the data are obsolete

15 lddate date load date

Category: Data Services Keys: Primary fpid Foreign typeid Data: Descriptive dir, dfile, foff, dsize, time, endtime, sta, chan, author, version, revision, obsolete Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 83 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

FKDISC

The fkdisc table contains descriptions of frequency-wave number (.fk) files.

TABLE 38: FKDISC

Column Storage Type Description

1 jdate number(8) Julian date

2 time float(53) epoch time

3 tlen float(24) time window

4 sta varchar2(6) station code

5 fktyp varchar2(4) f-k type

6 arid number(8) arrival identifier

7 maxkx float(24) maximum x-wavenumber

8 maxsx float(24) maximum x-slowness

9 nx number(4) number of x-samples

10 maxky float(24) maximum y-wavenumber

11 maxsy float(24) maximum y-slowness

12 ny number(4) number of y-samples

13 cfreq float(24) center frequency

14 bandw float(24) bandwidth

15 commid number(8) comment identifier

16 fkrid number(8) f-k recipe identifier

17 fkid number(8) f-k identifier

18 datsw number(10) data switch

19 foff number(10) byte offset of data segment within file

20 dir varchar2(64) f-k directory

21 dfile varchar2(32) f-k data file

22 lddate date load date

Database Schema

84 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

Category: Interactive Processing Keys: Primary fkid Alternate arid Foreign commid Data: Descriptive sta, datsw, foff, dir, dfile Measurement jdate, time, tlen, fktyp, maxkx, maxsx, nx, maxky, maxsy, ny, cfreq, bandw Administrative fkrid, lddate

Database Schema

IDC-5.1.1Rev5 October 2002 85 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

FORBEAMAUX

The forbeamaux table contains the channels for which amplitude measurements in the event lists and bulletins have been made.

TABLE 39: FORBEAMAUX

Column Storage Type Description

1 sta varchar2(6) station code

2 chan varchar2(8) channel code

Category: Data Services Keys: Primary sta/chan Data: Descriptive sta, chan

Database Schema

86 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

FPDESCRIPTION

The fpdescription table contains descriptions of product types used with file products.

TABLE 40: FPDESCRIPTION

Column Storage Type Description

1 typeid number(8) identifier for the product type description

2 prodtype varchar2(12) name of the product (should be the same as the protocol defining name)

3 name varchar2(64) descriptive listing of the product name

4 msgdtype varchar2(16) type of data (ASCII1, GIF89, and so on)

5 msgdformat varchar2(16) format of the data (GSE2.0, RMS1.0, and so on).

6 header_fpid number(8) fpid pointing to the header row for this product type

7 lddate date load date 1. American Standard Code for Information Interchange

Category: Data Services Keys: Primary typeid Data: Descriptive prodtype, name, msgdtype, msgdformat, header_fpid Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 87 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

FSAVE

The fsave table contains descriptions of an averaged Fourier spectrum (.fs) file.

TABLE 41: FSAVE

Column Storage Type Description

1 sta varchar2(6) station code

2 avtype varchar2(8) Fourier spectrum channel (ave, med, 95 percent, and so on)

3 fstype varchar2(4) Fourier spectrum type

4 maxf float(24) maximum frequency

5 nf number(8) number of frequency values

6 nave number(4) number of spectrums averaged

7 afsid number(8) averaged Fourier spectrum identifier

8 noissd float(24) standard deviation of log noise

9 datatype varchar2(2) numeric storage

10 dir varchar2(64) Fourier spectrum directory

11 dfile varchar2(32) Fourier spectrum data file

12 foff number(10) byte offset of data within file

13 commid number(8) comment identifier

14 lddate date load date

Category: Interactive Processing Keys: Primary afsid Alternate avtype/fstype/sta Foreign commid Data: Descriptive sta, avtype, fstype, datatype, dir, dfile, foff Measurement maxf, nave, nf, noissd Administrative lddate

Database Schema

88 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

FSDISC

The fsdisc table contains descriptions of a Fourier spectrum (.fs) file.

TABLE 42: FSDISC

Column Storage Type Description

1 fsid number(8) Fourier spectrum identifier

2 chanid number(8) channel identifier

3 wfid number(8) waveform identifier

4 fsrid number(8) fs recipe identifier

5 arid number(8) arrival identifier

6 jdate number(8) Julian date

7 time float(53) epoch time

8 tlen float(24) time window

9 sta varchar2(6) station code

10 chan varchar2(8) channel code

11 fstype varchar2(4) Fourier spectrum type

12 maxf float(24) maximum frequency

13 nf number(8) number of frequency values

14 datatype varchar2(2) numeric storage

15 dir varchar2(64) Fourier spectrum directory

16 dfile varchar2(32) Fourier spectrum data file

17 foff number(8) byte offset of data segment within file

18 commid number(8) comment identifier

19 lddate date load date

Database Schema

IDC-5.1.1Rev5 October 2002 89 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

Category: Interactive Processing Keys: Primary fsid Foreign chanid, wfid, fsrid, arid, commid Data: Descriptive sta, chan, datatype, dir, dfile, foff Measurement jdate, time, tlen, fstyp, maxf, nf Administrative lddate

Database Schema

90 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

FSRECIPE

The fsrecipe table contains recipe descriptions for generating Fourier spectrum (.fs) files.

TABLE 43: FSRECIPE

Column Storage Type Description

1 fsrid number(8) recipe identification

2 fsdesc varchar2(15) Fourier spectrum description

3 taper varchar2(8) type of taper (Hanning, Hamming, Cosine, and so on)

4 taperstart number(8) starting percent for cosine taper

5 taperend number(8) end percent for cosine taper

6 winlen number(8) number of points per window

7 overlap number(8) percent overlap of windows

8 nfft number(8) number of data points in the fft

9 smoothvalue float(24) amount of smoothing (Hz)

10 response varchar2(1) flag specifying instrument response correction

11 lddate date load date

Category: Interactive Processing Keys: Primary fsrid Data: Descriptive fsdesc, taper, taperstart, taperend, winlen, overlap, nfft, smoothvalue, response Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 91 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

FSTAG

The fstag table links individual spectrum files to the average spectrum file.

TABLE 44: FSTAG

Column Storage Type Description

1 afsid number(8) average Fourier spectra recipe identification

2 fsid number(8) Fourier spectrum identification

3 lddate date load date

Category: Interactive Processing Keys: Primary afsid/fsid Data: Administrative lddate

Database Schema

92 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

FTPFAILED

The ftpfailed table contains information on FTP data retrieval for AutoDRM.

TABLE 45: FTPFAILED

Column Storage Type Description

1 msgid number(8) message identifier

2 numfailedattempt number(4) number of failed attempts

3 lastfailedtime float(53) time of most recent attempt

4 ftp_address varchar2(64) FTP address

5 status varchar2(8) status of FTP attempt (retry or failed)

6 lddate date load date

Category: Data Services Keys: Primary msgid Foreign ftp_address Data: Descriptive status, ftp-address Measurement numfailedattempt, lastfailedtime Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 93 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

FTPLOGIN

The ftplogin table contains log on information for FTP data retrieval. The rows are used by the auxiliary data retrieval system to obtain data via FTP from auxiliary stations.

TABLE 46: FTPLOGIN

Column Storage Type Description

1 ftp_address varchar2(64) FTP address for auxiliary data

2 username varchar2(16) user name for FTP access

3 password varchar2(16) user password for FTP access

4 lddate date load date

Category: Data Services Keys: Primary ftp_address Data: Descriptive ftp_address, username, password Administrative lddate

Database Schema

94 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

FWFILE

The fwfile table contains file information used for buffering continuous data. An entry in this table describes the source station (sta) and the destination (ndc) for a particular stream of continuous data. A one-to-one relationship exists between a source station and a destination station. Fwhid and fwfid designate the identifiers (IDs) of the AlphaDLHeap and AlphaForward processes that service this file. This table is configured by an opera- tor, and the IDs are specified as parameters to the AlphaDLHeap and AlphaForward applications. Maxtime designates the maximum time that a gap in the data can span for a given station.

TABLE 47: FWFILE

Column Storage Type Description

1 fwhid number(8) identifier of the AlphaDLHeap process

2 fwfid number(8) identifier of the AlphaForward process

3 ndc varchar2(6) destination of the forwarded data

4 sta varchar2(6) station code

5 maxtime float(53) greatest time period for a gap

6 dir varchar2(64) directory name

7 dfile varchar2(32) heap filename

8 dfilesize number(9) buffer file size

9 lddate date load date

Category: Data Services Keys: Primary sta/ndc Data: Descriptive ndc, sta, fwfid, fwhid, dir, dfile, dfilesize Measurement maxtime Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 95 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

FWGAP

The fwgap table was used for tracking gaps in continuous data. Gap management is now handled by the continuous data subsystem but the table is still required by the Message Subsystem software.

TABLE 48: FWGAP

Column Storage Type Description

1 sta varchar2(6) station code

2 chan varchar2(8) channel code

3 ndc varchar2(6) destination of the forwarded data

4 time float(53) start time of gap

5 fwgid number(8) forward gap identifier

6 endtime float(53) end time of gap

7 framesize float(53) delta time of data frame

8 lddate date load date

Category: Data Services Keys: Primary fwgid Alternate sta/chan/ndc Data: Descriptive sta, chan, ndc Measurement time, endtime, framesize Administrative lddate

Database Schema

96 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

FWSITE

The fwsite table contains the possible destinations for forwarding data. An entry in this table describes the destination of the data (ndc), the fully qualified domain name of the machine where the connection manager resides (machine), and the port on which the connection manager is listening (port).

TABLE 49: FWSITE

Column Storage Type Description

1 ndc varchar2(6) destination of the forwarded data

2 machine varchar2(32) machine name

3 port number(6) listen port

4 priority number(2) priority of connection

5 lddate date load date

Category: Data Services Keys: Primary ndc/priority Data: Descriptive ndc, machine, port, priority Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 97 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

GA_TAG

The ga_tag table contains information on the use of arrivals and origins in the GA application.

TABLE 50: GA_TAG

Column Storage Type Description

1 objtype varchar2(1) type of identifier (a for arrival, o for origin)

2 id number(8) identification number (arid or orid)

3 state varchar2(20) use of arid or orid

Category: Automatic Processing Keys: Primary objtype/id/state Data: Descriptive objtype Measurement state

Database Schema

98 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

GLOSSARY

The glossary table contains information on abbreviations for the explosion database.

TABLE 51: GLOSSARY

Column Storage Type Description

1 abbrev varchar2(16) abbreviation name

2 abbrevtype varchar2(16) abbreviation type

3 lineno number(4) description line number

4 descrip varchar2(80) description

5 dir varchar2(64) directory

6 dfile varchar2(32) data file

7 lddate date load date

Category: Historical Keys: Primary abbrev/lineno Data: Descriptive abbrevtype, descrip, dir, dfile Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 99 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

GREGION

The gregion table contains geographic region numbers and their equivalent descriptions (see [Fli74]).

TABLE 52: GREGION

Column Storage Type Description

1 grn number(8) geographic region number

2 grname varchar2(40) geographic region name

3 lddate date load date

Category: Core, Reference Keys: Primary grn Data: Descriptive grn, grname Administrative lddate

Database Schema

100 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

HYDRO_ARR_GROUP

The hydro_arr_group table contains hydroacoustic arrival based estimates of slowness and azimuth.

TABLE 53: HYDRO_ARR_GROUP

Column Storage Type Description

1 hydro_id number(8) hydro-arrival-group identifier

2 az1 float(24) azimuth estimated from lag times

3 az2 float(24) second possible azimuth (2 arrivals)

4 slow float(24) slowness (s/km)

5 delaz float(24) azimuth uncertainty

6 nhydarr number(4) number of arrivals in hydro-arrival-group

7 net varchar2(8) hydro network name

8 hyd_grp_phase varchar2(8) hydro-arrival-group phase

9 lddate date load date

Category: Fundamental Keys: Primary hydro_id Foreign net Data: Descriptive nhydarr, hyd_grp_phase, slow Measurement az1, az2, delaz Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 101 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

HYDRO_ASSOC

The hydro_assoc table contains hydroacoustic arrival based estimates of slowness and azimuth.

TABLE 54: HYDRO_ASSOC

Column Storage Type Description

1 arid number(8) arrival identifier

2 hydro_id number(8) hydro-arrival-group identifier

3 azcontrib varchar2(1) azimuth contribution flag (y or n)

4 lddate date load date

Category: Fundamental Keys: Primary arid Foreign hydro_id Data: Descriptive azcontrib Administrative lddate

Database Schema

102 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

HYDRO_FEATURES

The hydro_features table contains feature measurements for hydroacoustic data from the DFX application.

TABLE 55: HYDRO_FEATURES

Column Storage Type Description

1 arid number(8) arrival identifier

2 peak_time float(53) time of largest absolute signal value

3 peak_level float(24) pressure of largest absolute signal value

4 total_energy float(24) total energy in signal

5 mean_arrival_time float(53) mean arrival time of signal energy

6 time_spread float(24) rms1 time spread of signal

7 onset_time float(53) estimated onset time of signal

8 termination_time float(53) estimated termination time of signal

9 total_time float(53) total time above threshold

10 num_cross number(8) number of signal threshold crossings

11 ave_noise float(24) average pressure of the noise segment

12 skewness float(24) skew of the estimated signal energy

13 kurtosis float(24) kurtosis of the estimated signal energy

14 cep_var_signal float(24) variance of the cepstrum using spectrum

15 cep_delay_time_signal float(24) bubble pulse delay time using spectrum

16 cep_peak_std_signal float(24) number of standard deviations from the mean for amplitude using spectrum

17 cep_var_trend float(24) variance of the cepstrum detrended using Noise Spectrum Equalization (NSE)

18 cep_delay_time_trend float(24) bubble pulse delay time estimate using trend NSE

19 cep_peak_std_trend float(24) number of standard deviations from the mean for amplitude using the trend

Database Schema

IDC-5.1.1Rev5 October 2002 103 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

TABLE 55: HYDRO_FEATURES (CONTINUED)

Column Storage Type Description

20 low_cut float(24) low-cut frequency of filter

21 high_cut float(24) high-cut frequency of filter

22 ford number(8) filter order

23 ftype varchar2(2) filter type

24 fzp number(8) filter causality

25 prob_weight_time float(53) probability-weighted time

26 sigma_time float(53) variance of the probability-weighted time

27 lddate date load date 1. root mean square

Category: Fundamental Keys: Primary arid Data: Descriptive low_cut, high_cut, ford, ftype, fzp Measurement peak_time, peak_level, total_energy, mean_arrival_time, time_spread, onset_time, termination_time, total_time, num_cross, ave_noise, skewness, kurtosis, cep_var_signal, cep_delay_time_signal, cep_peak_std_signal, cep_var_trend, cep_delay_time_trend, cep_peak_std_trend, prob_weight_time, sigma_time Administrative lddate

Database Schema

104 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

INFRA_FEATURES

The infra_features table contains feature measurements for infrasonic data from the DFX application.

TABLE 56: INFRA_FEATURES

Column Storage Type Description

1 arid number(8) arrival identifier

2 eng_time float(53) energy start time

3 eng_dur float(24) energy duration

4 eng_deldur float(24) standard deviation for energy duration

5 coh_time float(53) coherence start time

6 coh_dur float(24) coherence duration

7 coh_deldur float(24) standard deviation for coherence duration

8 coinc_time float(53) coincident start time

9 coinc_dur float(24) coincident duration

10 coinc_deldur float(24) standard deviation for coincident duration

11 ford number(8) filter order

12 zrcr_freq float(24) zero crossing frequency

13 zrcr_delfreq float(24) standard deviation for zero crossing frequency

14 crnr_freq float(24) corner frequency

15 crnr_delfreq float(24) standard deviation for corner frequency

16 coh_per float(24) spatial coherence period

17 coh_snr float(24) spatial coherence signal-to-noise ratio

18 total_energy float(24) total energy

Database Schema

IDC-5.1.1Rev5 October 2002 105 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

TABLE 56: INFRA_FEATURES (CONTINUED)

Column Storage Type Description

19 auth varchar2(15) author

20 commid number(8) comment identifier

21 lddate date load date

Category: Fundamental Keys: Primary arid Foreign commid Data: Descriptive ford Measurement eng_time, eng_dur, eng_deldur, coh_time, coh_dur, coh_deldur, coinc_time, coinc_dur, coinc_deldur, zrcr_freq, zrcr_delfreq, crnr_freq, crnr_delfreq, coh_per, coh_snr, total_energy Administrative auth, lddate

Database Schema

106 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

INSTRUMENT

The instrument table contains ancillary calibration information. This table holds nominal one-frequency calibration factors for each instrument and pointers to the nominal frequency-dependent calibration for an instrument. It also holds pointers to the exact cali- brations obtained by direct measurement on a particular instrument (see sensor).

TABLE 57: INSTRUMENT

Column Storage Type Description

1 inid number(8) instrument identifier

2 insname varchar2(50) instrument name

3 instype varchar2(6) instrument type

4 band varchar2(1) frequency band

5 digital varchar2(1) data type, digital (d), or analog (a)

6 samprate float(24) sampling rate in samples/second

7 ncalib float(24) nominal calibration (nanometers/digital count)

8 ncalper float(24) nominal calibration period (seconds)

9 dir varchar2(64) directory

10 dfile varchar2(32) data file

11 rsptype varchar2(6) response type

12 lddate date load date

Category: Core, Reference Keys: Primary inid Data: Descriptive insname, instype, band, digital, dir, dfile, rsptype Measurement samprate, ncalib, ncalper Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 107 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

INTERVAL

The interval table defines units of processing. The time, endtime, and name fields indicate processing times for a named object. The class field allows a single interval table to be used for different classes of objects.

TABLE 58: INTERVAL

Column Storage Type Description

1 intvlid number(8) interval identifier

2 class varchar2(16) type of interval

3 name varchar2(20) name of interval

4 time float(53) starting time of data

5 endtime float(53) ending time of data

6 state varchar2(16) current processing state

7 moddate date time of last processing state change

8 lddate date load date

Category: Distributed Processing Keys: Primary class/name/time/endtime Alternate intvlid Data: Descriptive class, name, state Measurement time, endtime Administrative moddate, lddate

Database Schema

108 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

LASTID, PROBLASTID, RMS_LASTID

The lastid table contains counter values (last value used for keys). This table is a reference table from which programs may retrieve the last sequential value of one of the numeric keys. Unique keys are required before inserting a record in numerous tables. The table has exactly one row for each keyname. Problastid and rms_lastid are views of the lastid table.

TABLE 59: LASTID (PROBLASTID, RMS_LASTID)

Column Storage Type Description

1 keyname varchar2(15) identifier name (arid, orid, and so on)

2 keyvalue number(8) last value used for that identifier

3 lddate date load date

Category: Database and Utility Keys: Primary keyname Data: Descriptive keyname, keyvalue Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 109 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

LOCATION

The location table contains information on mines and test sites.

TABLE 60: LOCATION

Column Storage Type Description

1 locname varchar2(15) location name

2 sublocname varchar2(25) sub-location name

3 locid varchar2(30) location identifier

4 lat float(24) latitude

5 lon float(24) longitude

6 elev float(24) surface elevation (km)

7 tdepth float(24) tunnel depth

8 descrip varchar2(50) text description

9 auth varchar2(15) author

10 commid number(8) comment identifier

11 lddate date load date

Category: Historical Keys: Primary locid Alternate lat/lon/elev/tdepth Foreign commid Data: Descriptive locname, sublocname, locid, descrip Measurement lat, lon, elev, tdepth Administrative auth, lddate

Database Schema

110 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

MAPCOLOR

The mapcolor table contains information to associate a mapid from the mapdisc table with a colormapid from the colordisc table. This table is used to plot the same map (mapid) in different colors (for example, brown, green, or outline).

TABLE 61: MAPCOLOR

Column Storage Type Description

1 mapid number(8) map identifier

2 colormapid number(8) colormap identifier

3 lddate date load date

Category: Interactive Processing Keys: Primary mapid/colormapid Data: Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 111 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

MAPDISC

The mapdisc table contains information about map files that are on disk.

TABLE 62: MAPDISC

Column Storage Type Description

1 mapid number(8) map identifier

2 mapname varchar2(64) map name

3 dfile varchar2(32) map data filename

4 dir varchar2(64) directory

5 maptype number(8) map type

6 mapfiletype varchar2(4) map file type

7 projection number(8) map projection

8 dimx number(8) map x dimension

9 dimy number(8) map y dimension

10 reflon float(24) reference longitude

11 reflat float(24) reference latitude

12 refoffsetlon float(24) longitude reference offset

13 refoffsetlat float(24) latitude reference offset

14 lonorigradians float(24) longitude origin radians

15 latorigradians float(24) latitude origin radians

16 scale float(24) map scale

17 rotation float(24) map rotation

18 latminor float(24) latitude interval for minor grid lines

19 latmajor float(24) latitude interval for major grid lines

20 lonminor float(24) longitude interval for minor grid lines

21 lonmajor float(24) longitude interval for major grid lines

22 bordercolor varchar2(32) border color name

Database Schema

112 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

TABLE 62: MAPDISC (CONTINUED)

Column Storage Type Description

23 label varchar2(65) map category

24–38 gctp1 through gctp15 float(53) general cartographic transformation package variables

39 lddate date load date

Category: Interactive Processing Keys: Primary mapid Data: Descriptive mapname, dfile, dir, maptype, mapfiletype, projection, bordercolor, label Measurement dimx, dimy, reflon, reflat, refoffsetlon, refoffsetlat, lonorigradians, latorigradians, scale, rotation, latminor, latmajor, lonminor, lonmajor, gctp1–15 Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 113 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

MAPOVER

The mapover table contains links between the mapdisc and overlaydisc tables.

TABLE 63: MAPOVER

Column Storage Type Description

1 mapid number(8) map identifier

2 overlayid number(8) overlay identifier

3 lddate date load date

Category: Interactive Processing Keys: Primary mapid/overlayid Data: Administrative lddate

Database Schema

114 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

MAPPOINT

The mappoint table contains labeled point data to be displayed by the Map application.

TABLE 64: MAPPOINT

Column Storage Type Description

1 lat float(24) latitude

2 lon float(24) longitude

3 mplabel varchar2(65) map point type

4 mptype varchar2(20) map point label

5 mpdescrip varchar2(50) map point description

6 lddate date load date

Category: Interactive Processing Keys: Primary lat/lon/mptype Data: Descriptive lat, lon, mplabel, mptype, mpdescrip Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 115 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

MIG_DATE

The mig_date table is used by the MigrateData application to track table migration.

TABLE 65: MIG_DATE

Column Storage Type Description

1 procclass varchar2(16) process class

2 procname varchar2(16) process name

3 last_mig_date date last migration date

4 lddate date load date

Category: Data Services Keys: Primary procclass/procname Data: Descriptive procclass, procname, last_mig_date Administrative lddate

Database Schema

116 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

MIG_RULES

The mig_rules table contains rules for migrating database tables from one database table to another and are specified in Table 66.

TABLE 66: MIG_RULES

Column Storage Type Description

1 task_num number order of this task

2 query_type varchar2(20) type of query

3 src varchar2(10) source database

4 src_tbl varchar2(30) source table

5 dest varchar2(10) destination database

6 dest_tbl varchar2(30) destination table

7 quer_seq_no number order of this part of the query

8 seq_type varchar2(15) type of sequence to be added to the query

9 seq_contents varchar2(200) query contents

Category: Data Services Keys: Primary task_num/query_type/src_tbl Data: Descriptive task_num, query_type, src, src_tbl, dest, dest_tbl, quer_seq_no, seq_type, seq_contents

Database Schema

IDC-5.1.1Rev5 October 2002 117 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

MSGAUX

The msgaux table contains records of unsuccessfully processed AutoDRM messages.

TABLE 67: MSGAUX

Column Storage Type Description

1 msgid number(8) message identifier

2 msgrow number(4) line number in message

3 state_count number(4) number of failures

4 command varchar2(24) AutoDRM command that could not be processed

5 sub_status varchar2(24) cause of failure

6 lddate date load date

Category: Data Services Keys: Primary msgid/msgrow/state_count Data: Descriptive command, sub_status Measurement msgrow, state_count Administrative lddate

Database Schema

118 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

MSGDATATYPE

The msgdatatype table supports data tracking by recording each data section in a message for both incoming and outgoing AutoDRM data messages.

TABLE 68: MSGDATATYPE

Column Storage Type Description

1 msgid number(8) message identifier

2 msgdtype varchar2(16) data type of the data section within the message

3 msgdformat varchar2(16) general format of data that follows

4 status varchar2(32) status of the data section

5 foff number(8) file offset to beginning of data section

6 msize number(8) size of data section

7 lddate date load date

Category: Data Services Keys: Primary msgid/foff Data: Descriptive msgdtype, msgdformat Measurement status, foff, msize Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 119 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

MSGDEST

The msgdest table contains information about AutoDRM messages sent from the IDC.

TABLE 69: MSGDEST

Column Storage Type Description

1 msgdid number(8) message destination identifier

2 msgid number(8) message identifier

3 transmeth varchar2(16) method by which the response is to be delivered to the requester

4 emailto varchar2(64) email address to send message

5 status varchar2(32) current status of the response message

6 itime float(53) time at which table entry was made

7 stime float(53) time at which message was sent

8 lddate date load date

Category: Data Services Keys: Primary msgdid Foreign msgid Data: Descriptive transmeth Data emailto, status, stime, itime Administrative lddate

Database Schema

120 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

MSGDISC

The msgdisc table contains information pertinent to AutoDRM messages including the date and time that the message was sent or received, identification information, and where the message is stored.

TABLE 70: MSGDISC

Column Storage Type Description

1 msgid number(8) message identifier

2 userid number(8) user identifier

3 msgver varchar2(8) message system version number

4 msgtype varchar2(16) message type

5 subtype varchar2(2) message subtype

6 extmsgid varchar2(20) message identification string provided by the sender

7 intid number(8) either the locally generated msgid of an earlier table entry that evoked the cre- ation of this table entry or the reqid from the request table of an internally generated request

8 intidtype varchar2(16) intid type

9 msgsrc varchar2(16) message source code

10 itime float(53) initial time message was received

11 idate number(8) initial date message was received

12 imethod varchar2(8) input method (email or ftp)

13 isrc varchar2(64) initial source of message

14 msize number(10) message size in bytes

15 status varchar2(32) status of message

16 subject varchar2(64) subject header from email message

17 dir varchar2(64) directory to find file

18 dfile varchar2(32) name of data file

Database Schema

IDC-5.1.1Rev5 October 2002 121 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

TABLE 70: MSGDISC (CONTINUED)

Column Storage Type Description

19 foff number(10) byte offset of data segment within file

20 mfoff number(10) offset in bytes to beginning of message

21 fileoff number(10) number of bytes to the first character of the emal file (first character of the email header)

22 filesize number(10) size of file

23 sigtype varchar2(64) digital signature type

24 verifstatus varchar2(4) status of verification

25 commid number(8) comment identifier

26 lddate date load date

Category: Data Services Keys: Primary msgid Foreign userid, intid, commid Data: Descriptive msgver, msgtype, intidtype, subtype, msgsrc, status, subject, dir, dfile, foff, mfoff, fileoff, filesize, sigtype, verifstatus Measurement extmsgid, intid, itime, idate, imethod, isrc, msize Administrative lddate

Database Schema

122 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

NA_VALUE

The na_value table contains the default values to be inserted for a column when not available.

TABLE 71: NA_VALUE

Column Storage Type Description

1 attribute varchar2(30) column name

2 na_value varchar2(30) value inserted when not available

Category: Database and Utility Keys: Primary attribute Data: Descriptive attribute, na_value

Database Schema

IDC-5.1.1Rev5 October 2002 123 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

NETMAG

The netmag table contains estimates of network magnitudes of different types for an event. Each network magnitude has a unique magid. Station magnitudes used to compute the network magnitude are in the stamag table.

TABLE 72: NETMAG

Column Storage Type Description

1 magid number(8) network magnitude identifier

2 net varchar2(8) unique network identifier

3 orid number(8) origin identifier

4 evid number(8) event identifier

5 magtype varchar2(6) magnitude type (Ms, mb, and so on)

6 nsta number(8) number of stations used

7 magnitude float(24) magnitude

8 uncertainty float(24) magnitude uncertainty

9 auth varchar2(15) source/originator

10 commid number(8) comment identifier

11 lddate date load date

Category: Core, Fundamental Keys: Primary magid Foreign evid, net, orid, commid Data: Descriptive net, magtype Measurement magnitude, nsta, uncertainty Administrative auth, lddate

Database Schema

124 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

NETWORK

The network table contains general information about seismic networks (see affiliation).

TABLE 73: NETWORK

Column Storage Type Description

1 net varchar2(8) unique network identifier

2 netname varchar2(80) network name

3 nettype varchar2(4) network type: array, local, world-wide, and so on

4 auth varchar2(15) source/originator

5 commid number(8) comment identifier

6 lddate date load date

Category: Core, Reference Keys: Primary net Foreign commid Data: Descriptive net, netname, nettype Administrative auth, lddate

Database Schema

IDC-5.1.1Rev5 October 2002 125 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

ORIGAUX

The origaux table contains additional data for supplementary events that cannot be inserted into origin, origerr, netmag, and remark tables.

TABLE 74: ORIGAUX

Column Storage Type Description

1 event varchar2(8) unique event identifier (string)

2 otfixf varchar2(1) origin time fixed flag

3 epfixf varchar2(1) epicenter fixed flag

4 nsta number(8) number of defining stations

5 gap number(4) gap in azimuth coverage (degrees)

6 ident varchar2(8) unique ident (string)

7 mindist float(24) distance to closest station (degrees)

8 maxdist float(24) distance to farthest station (degrees)

9 antype varchar2(1) analysis type

10 evid number(8) event identifier

11 orid number(8) origin identifier

12 lddate date load date

Category: System Monitoring Keys: Primary orid Foreign evid Data: Descriptive antype, epfixf, otfixf Measurement gap, maxdist, mindist, nsta Administrative event, ident, lddate

Database Schema

126 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

ORIGERR, ORIGERR_TEMP_GA

The origerr table contains summaries of confidence bounds in origin estimations. The origerr_temp_ga table is used by the GA application to store temporary origin error information. The measurement fields are the elements of the location covariance matrix. The descriptive fields give the uncertainties in location, depth, and origin time. These quantities are calculated from the covariance matrix, assuming gaussian errors and a confidence level conf.

TABLE 75: ORIGERR (ORIGERR_TEMP_GA)

Column Storage Type Description

1 orid number(8) origin identifier

2–11 sxx, syy, szz, stt, sxy, sxz, float(24) covariance matrix elements syz, stx, sty, stz

12 sdobs float(24) standard error of observations

13 smajax float(24) semi-major axis of error

14 sminax float(24) semi-minor axis of error

15 strike float(24) strike of the semi-major axis

16 sdepth float(24) depth error

17 stime float(24) origin time error

18 conf float(24) confidence

19 commid number(8) comment identifier

20 lddate date load date

Category: Core, Fundamental Keys: Primary orid Foreign commid Data: Descriptive sdobs, smajax, sminax, strike, sdepth, stime, conf Measurement sxx, syy, szz, stt, sxy, sxz, syz, stx, sty, stz Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 127 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

ORIGIN, ORIGINREF, ORIGIN_TEMP_GA

The origin, originref, and origin_temp_ga tables contain information describing a derived or reported origin for a particular event. The origin_temp_ga table is used by the GA application to store temporary origins.

TABLE 76: ORIGIN (ORIGINREF, ORIGIN_TEMP_GA)

Column Storage Type Description

1 lat float(24) estimated latitude

2 lon float(24) estimated longitude

3 depth float(24) estimated depth

4 time float(53) epoch time

5 orid number(8) origin identifier

6 evid number(8) event identifier

7 jdate number(8) Julian date

8 nass number(4) number of associated phases

9 ndef number(4) number of locating phases

10 ndp number(4) number of depth phases

11 grn number(8) geographic region number

12 srn number(8) seismic region number

13 etype varchar2(7) event type

14 depdp float(24) estimated depth from depth phases

15 dtype varchar2(1) depth method used

16 mb float(24) body wave magnitude

17 mbid number(8) mb magnitude identifier 18 ms float(24) surface wave magnitude

19 msid number(8) Ms magnitude identifier 20 ml float(24) local magnitude

Database Schema

128 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

TABLE 76: ORIGIN (ORIGINREF, ORIGIN_TEMP_GA) (CONTINUED)

Column Storage Type Description

21 mlid number(8) ML magnitude identifier 22 algorithm varchar2(15) location algorithm used

23 auth varchar2(15) source/originator

24 commid number(8) comment identifier

25 lddate date load date

Category: Core, Fundamental Keys: Primary orid Alternate lat/lon/depth/time Foreign evid, mbid, msid, mlid, commid Data: Descriptive nass, ndef, ndp, grn, srn, etype Measurement lat, lon, depth, time, jdate, depdp, dtype, mb, mbid, ms, msid, ml, mlid Administrative algorithm, auth, lddate

Database Schema

IDC-5.1.1Rev5 October 2002 129 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

OUTAGE

The outage table contains the availability of time-series data. If the available column is set to “f,” it specifies that no data are available for the interval. Conversely, the outage table can be used to specify that data are available for an interval by setting the available column to “t.”

TABLE 77: OUTAGE

Column Storage Type Description

1 otgid number(8) outage identifier

2 sta varchar2(6) station code

3 chan varchar2(8) channel code

4 auxid varchar2(4) auxiliary identification code

5 time float(53) start time of outage interval

6 endtime float(53) end time of outage interval

7 status varchar2(32) status of outage

8 auth varchar2(15) source/originator of outage report

9 available varchar2(1) flag to specify if data are unavailable (f) or available (t)

10 commid number(8) comment identifier

11 lddate date load date

Category: Data Services Keys: Primary otgid Alternate sta/chan/time/endtime Data: Descriptive sta, chan, auxid, status, auth, available, commid Measurement time, endtime Administrative lddate

Database Schema

130 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

OVERLAYDISC

The overlaydisc table contains the location of the overlays for the Map application.

TABLE 78: OVERLAYDISC

Column Storage Type Description

1 overlayid number(8) overlay identifier

2 overlayname varchar2(64) overlay name

3 dfile varchar2(32) data filename

4 dir varchar2(64) directory

5 colorname varchar2(32) overlay color name

6 lddate date load date

Category: Interactive Processing Keys: Primary overlayid Data: Descriptive overlayname, dfile, dir, colorname Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 131 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

PARRIVAL

The parrival table contains the predicted arrivals and associations for origin-based amplitude measurements.

TABLE 79: PARRIVAL

Column Storage Type Description

1 parid number(8) predicted arrival identifier

2 orid number(8) origin identifier

3 evid number(8) event identifier

4 sta varchar2(6) station code

5 time float(53) epoch time

6 azimuth float(24) azimuth

7 slow float(24) slowness (s/deg)

8 phase varchar2(8) associated phase

9 delta float(24) station to event distance

10 vmodel varchar2(15) velocity model

11 lddate date load date

Category: Fundamental Keys: Primary parid Alternate sta/time Foreign orid, evid Data: Descriptive sta, phase, vmodel Measurement time, azimuth, slow, delta Administrative lddate

Database Schema

132 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

PARTICIPATION

The participation table contains station participation information for performance reporting.

TABLE 80: PARTICIPATION

Column Storage Type Description

1 net varchar2(8) network name

2 sta varchar2(6) station name

3 begin_date number(8) date participation began

4 end_date number(8) date participation ended

5 lddate date load date

Category: Reference Keys: Primary net/sta Data: Descriptive net, sta Measurement begin_date, end_date Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 133 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

PROBLEM

The problem table contains information related to problems with stations, communica- tions, software, and hardware.

TABLE 81: PROBLEM

Column Storage Type Description

1 prid number(8) problem identifier

2 procclass varchar2(17) process class

3 procname varchar2(17) process name

4 time number(17,5) epoch time of start of problem

5 endtime number(17,5) epoch time of end of problem

6 status varchar2(33) status of problem

7 class varchar2(33) class of problem

8 descrip varchar2(129) one line description of problem

9 login varchar2(33) login name of originator

10 lddate date load date

Category: System Monitoring Keys: Primary prid Data: Descriptive procclass, procname, status, class, descrip, login Measurement time, endtime Administrative lddate

Database Schema

134 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

PROBLEMLOG

The problemlog table contains individual problem log entries relating to problems in the database table.

TABLE 82: PROBLEMLOG

Column Storage Type Description

1 plid number(8) problem log identifier

2 prid number(8) problem identifier

3 time number(17,5) time of log entry

4 dir varchar2(129) directory of log file

5 dfile varchar2(65) filename of log file

6 login varchar2(33) login name of originator

7 lddate date load date

Category: System Monitoring Keys: Primary plid Foreign prid Data: Descriptive dir, dfile, login Measurement time Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 135 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

PROBLEMMAIL

The problemmail table contains instructions for distributing problem messages to sub- scribers.

TABLE 83: PROBLEMMAIL

Column Storage Type Description

1 procclass varchar2(17) subscription category

2 login varchar2(33) login name of originator

3 lddate date load date

Category: System Monitoring Keys: Primary procclass/login Data: Descriptive procclass, login Administrative lddate

Database Schema

136 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

PRODTRACK

The prodtrack table queues and links data and subscription products. The dataid column links the product delivery to the data encapsulated in the dataready table, and the msgid column links the product to the outgoing message, as referenced in the msgdisc table. Thus, the prodtrack table allows for subscription tracking from the data to the product.

TABLE 84: PRODTRACK

Column Storage Type Description

1 prodid number(8) product identifier

2 delivid number(8) delivery identifier

3 dataid number(8) data ready identifier

4 msgid number(8) message identifier

5 status varchar2(12) status of the product

6 lddate date load date

Category: Data Services Keys: Primary prodid/dataid/msgid Foreign dataid, msgid Data: Descriptive delivid, status Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 137 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

PRODUCTCRITERIA

The productcriteria table contains subscription information about the type of product and when and how often to distribute the data. Each unique product has one record.

TABLE 85: PRODUCTCRITERIA

Column Storage Type Description

1 prodid number(8) product identifier

2 prodname varchar2(24) product name (if a standard product)

3 delivid number(8) last delivery for this product

4 cycle_size number(8) product size to be reached before release (0 for no limit)

5 cycle_time number(4) time interval between releases (0 for immediate)

6 hour_to_send number(2) hour to send product

7 dow_to_send number(2) day of week to send subscription

8 dom_to_send number(2) day of month to send subscription

9 prodtype varchar2(32) product type (origin, detection, and so on)

10 prodsubtype varchar2(12) product subtype (for example, bulletin type)

11 prodfmt varchar2(6) format of outgoing product

12 supressempty char(2) if “no,” empty messages may be sent

13 timelastsend float(54) epoch time of the last transmission

14 timenextsend float(54) epoch time of the next transmission

15 lddate date load date

Database Schema

138 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

Category: Data Services Keys: Primary prodid Data: Descriptive prodname, cycle_site, cycle_time, hour_to_send, how_to_send, dom_to_send, prodtype, prodsubtype, prodfmt, supress_empty Measurement delivid, timelastsend, timenextsend Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 139 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

PRODUCTTYPEEVSC

The producttypeevsc table contains the input parameters that define the event-screening criteria for the standard case and national subscriptions. It is used in conjunction with the producttypeorigin table to specify the set of user input criteria. There is one record for each subscription (prodid).

TABLE 86: PRODUCTTYPEEVSC

Column Storage Type Description

1 prodid number(8) product identifier

2 grpname varchar2(24) subscription group name

3 regname varchar2(24) region name

4 min_ndef number(8) minimum number of defining phases

5 min_mb float(24) minimum mb for screening

6 depth_conf float(24) depth screening confidence

7 depth_thresh float(24) depth screening threshold

8 depth_kvalue float(24) depth uncertainty k-value

9 min_ndp_pp number(8) minimum required number of pP depth phases

10 min_ndp_sp number(8) minimum required number of sP depth phases

11 min_moveout_pp float(24) minimum moveout of pP–P travel time differences

12 min_moveout_sp float(24) minimum moveout of sP–P travel time differences

13 min_dp_snr_pp float(24) minimum pP depth phase snr

14 min_dp_snr_sp float(24) minimum sP depth phase snr

15 mbms_conf float(24) mb minus Ms screening confidence

16 mbms_thresh float(24) mb minus Ms screening threshold

17 mbms_slope float(24) slope term for mb minus Ms relation

Database Schema

140 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

TABLE 86: PRODUCTTYPEEVSC (CONTINUED)

Column Storage Type Description

18 magpref_mb varchar2(6) mb magnitude type used for screening.

19 magpref_ms varchar2(6) Ms magnitude type used for screening.

20 mb_err float(24) single-station mb uncertainty

21 ms_err float(24) single-station Ms uncertainty 22 min_nsta_ms number(8) minimum number of stations for ms

23 loc_conf float(24) location error ellipse confidence

24 hydro_te_thresh float(24) hydroacoustic total energy threshold

25 hydro_cp_thresh float(24) hydroacoustic cepstral peak threshold

26 min_wdepth_thresh float(24) minimum water depth threshold

27 reg_conf float(24) regional screening confidence

28 lddate date load date

Category: Data Services Keys: Primary prodid/grpname/regname Data: Descriptive min_ndef, min_mb, depth_conf, depth_thresh, depth_kvalue, min_ndp_pp, min_ndp_sp, min_moveout_pp, min_moveout_ps, min_dp_snr_pp, min_dp_snr_sp, mbms_conf, mbms_thresh, mbms_slope, magpref_mb, magpref_ms, mb_err, ms_err, min_nsta_ms, loc_conf, hydro_te_thresh, hydro_cp_thresh, min_wdepth_thresh, reg_conf Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 141 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

PRODUCTTYPEORIGIN

The producttypeorigin table contains the details of origin subscriptions. It extends the productcriteria table that is generic to all subscriptions. Each origin-based product has one record.

TABLE 87: PRODUCTTYPEORIGIN

Column Storage Type Description

1 prodid number(8) product identifier

2 minlat float(24) minimum latitude of event

3 maxlat float(24) maximum latitute of event

4 minlon float(24) minimum longitude of event

5 maxlon float(24) maximum longitude of event

6 mindepth float(24) minimum depth of event

7 maxdepth float(24) maximum depth of event

8 minmag float(24) minimum magnitude

9 maxmag float(24) maximum magnitude

10 magtype varchar2(4) magnitude type

11 minmb_ms float(24) minimum value of mb minus Ms

12 maxmb_ms float(24) maximum value of mb minus Ms 13 mindep_err float(24) minimum value of depth minus error

14 maxdep_err float(24) maximum value of depth minus error

15 minesd float(24) minimum event-station distance

16 maxesd float(24) maximum event-station distance

Database Schema

142 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

Category: Data Services Keys: Primary prodid Data: Descriptive minlat, maxlat, minlon, maxlon, mindepth, maxdepth, minmag, maxmag, magtype, minmb_ms, maxmb_ms, mindep_err, maxdep_err, minesd, maxesd

Database Schema

IDC-5.1.1Rev5 October 2002 143 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

PRODUCTTYPESTA

The producttypesta table contains the criteria used for defining subscription products with constraints that are based on the station. If a user requests a subscription for multiple stations, the table will have one productcriteria row, but multiple producttypesta rows (one for each station); all of the producttypesta rows will have a common value of prodid.

TABLE 88: PRODUCTTYPESTA

Column Storage Type Description

1 prodid number(8) product identifier

2 minlat float(24) minimum station latitude

3 maxlat float(24) maximum station latitude

4 minlon float(24) minimum station longitude

5 maxlon float(24) maximum station longitude

6 sta varchar2(6) station name

7 chan varchar2(8) channel name

Category: Data Services Keys: Primary prodid/sta/chan Data: Descriptive minlat, maxlat, minlon, maxlon, sta, chan

Database Schema

144 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

QCSTATS

The qcstats table contains waveform data quality statistics.

TABLE 89: QCSTATS

Column Storage Type Description

1 qcstatsid number(8) data quality statistics identifier

2 sta varchar2(6) station name

3 chan varchar2(8) channel name

4 time float(53) interval start time

5 jdate number(8) Julian date

6 endtime float(53) interval end time

7 dettime float(53) detection interval start time

8 detendtime float(53) detection interval end time

9 missing float(53) amount of missing data

10 dropped number(8) flag indicating if interval was dropped

11 nseg number(8) number of masked segments

12 masked float(53) amount of data in masked segments

13 pointspike float(53) amount of data in masked due to point-spikes

14 spike float(53) amount of data in masked due to spikes

15 nconstseg number(8) number of constant valued segments

16 const float(53) amount of data masked due to constant valued segments

17 avgconstval float(53) average value in constant segments

18 stdconstval float(53) standard deviation of constant values

19 auth varchar2(15) author

20 lddate date load date

Database Schema

IDC-5.1.1Rev5 October 2002 145 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

Category: System Monitoring Keys: Primary qcstatsid Data: Descriptive sta, chan Measurement time, jdate, endtime, dettime, detendtime, missing, dropped, nseg, masked, pointspike, spike, nconstseg, const, avgconstval, stdconstval Administrative auth, lddate

Database Schema

146 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

REBDONE_DATADAY_FLAG

The rebdone_dataday_flag table contains the status of Reviewed Event Bulletin (REB) bulletin generation.

TABLE 90: REBDONE_DATADAY_FLAG

Column Storage Type Description

1 dataday number(12) Julian day

2 state varchar2(12) state of processing

3 donetime float(53) time that REB was produced

4 lddate date load date

Category: Interactive Processing Keys: Primary dataday Data: Descriptive state Measurement dataday, donetime Administration lddate

Database Schema

IDC-5.1.1Rev5 October 2002 147 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

REF_LOC

The ref_loc table contains reference locations for comparing origins to known geographic locations. This table is used by the ExAnComp application.

TABLE 91: REF_LOC

Column Storage Type Description

1 refid number(8) reference location identifier

2 refname varchar2(16) reference location name

3 lat float(24) latitude

4 lon float(24) longitude

5 descrip varchar2(80) description

6 lddate date load date

Category: System Monitoring Keys: Primary refid Data: Descriptive refname, lat, lon, descrip Administrative lddate

Database Schema

148 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

REGCOEF

The regcoef table contains linear coefficients for regional processing.

TABLE 92: REGCOEF

Column Storage Type Description

1 rcoefid varchar2(20) linear coefficient set identifier

2 rcoeftype varchar2(10) linear coefficient value identifier

3 rcoefvalue float(24) linear coefficient value

4 ondate number(8) Julian start date

5 offdate number(8) Julian stop date

6 lddate date load date

Category: Fundamental Keys: Primary rcoefid/rcoeftype Data: Descriptive ondate, offdate, rcoefvalue Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 149 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

REMARK

The remark table contains comments. This table may be used to store free-form comments that embellish records of other tables. The commid field in many tables refers to a record in the remark table. If commid is null (–1) in a record of any other table, no comments are stored for that record.

TABLE 93: REMARK

Column Storage Type Description

1 commid number(8) comment identifier

2 lineno number(8) comment line number

3 remark varchar2(80) free-format comment

4 lddate date load date

Category: Database and Utility Keys: Primary commid/lineno Data: Descriptive lineno, remark Administrative lddate

Database Schema

150 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

REQUEST

The request table defines segments of auxiliary waveform data to be acquired. The start_time, end_time, sta and chan fields define a single unit of data. Data import programs must succeed in acquiring all the data for a time interval before changing the state to indicate success.

TABLE 94: REQUEST

Column Storage Type Description

1 reqid number(8) request identifier

2 sta varchar2(6) station code

3 chan varchar2(8) channel code

4 array varchar2(8) array code

5 orid number(8) origin identifier

6 evid number(8) event identifier

7 start_time float(53) starting time of requested waveform data

8 end_time float(53) ending time of requested waveform data

9 class varchar2(16) type of request

10 state varchar2(16) current request status

11 statecount number(8) number of failed attempts (when state = failed)

12 complete number(8) percentage of data acquired

13 requestor varchar2(15) original author of record

14 modtime float(53) time of last state change (epoch time)

15 modauthor varchar2(15) author of last state change

16 lddate date load date

Database Schema

IDC-5.1.1Rev5 October 2002 151 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

Category: Data Services Keys: Primary reqid Alternate sta/chan/start_time/end_time Foreign orid, evid Data: Descriptive sta, chan, array, class requestor, modauthor Measurement start_time, end_time, state, statecount, complete, modtime Administrative lddate

Database Schema

152 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

REVAUDIT

The revaudit table keeps a history of the revisions made to an event.

TABLE 95: REVAUDIT

Column Storage Type Description

1 revid number(8) revision identifier

2 revfunction varchar2(32) name of the revision function used

3 auth varchar2(15) author (originator) of the revision

4 revtagid1 number(8) revtagname1 value; the value of the foreign key identified in revtagname1

5 revtagname1 varchar2(8) revtagname1 type; the name of the foreign key whose value is revtagid1

6 revtagid2 number(8) revtagname2 value; the value of the foreign key identified in revtagname2

7 revtagname2 varchar2(8) revtagname2 type; the name of the foreign key whose value is revtagid2

8 revstate varchar2(16) state of the revision

9 lddate date load date

Category: Interactive processing Keys: Primary revid Foreign revtagid1, revtagid2 Data: Descriptive revfunction, auth, revtagname1, revtagname2, revstate Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 153 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

SCAN_DATE

The scan_date table is used to track which data days were scanned for events missed by the automatic system.

TABLE 96: SCAN_DATE

Column Storage Type Description

1 jdate number(8) Julian date

2 scan varchar2(1) scanning status = y, n

Category: Interactive Processing Keys: Primary jdate Data: Descriptive scan Measurement jdate

Database Schema

154 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

SEISGRID, DSEISGRID

The seisgrid table contains a natural seismicity grid, which includes the average number of events per year with magnitude greater than the threshold in this table for each latitude-longitude grid point (the grid points are defined in the seisindex table). The seisgrid table is used by the AEQ application to help identify anomalous events.

TABLE 97: SEISGRID (DSEISGRID)

Column Storage Type Description

1 grdname varchar2(6) grid name

2 icell number(8) grid cell index

3 magth float(24) magnitude threshold

4 magtype varchar2(6) magnitude type

5 nevyr float(24) average number of events/year

6 lddate date load date

Category: Automatic Processing Keys: Primary grdname/icell Data: Descriptive grdname, icell, magth, magtype Measurement nevyr Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 155 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

SEISINDEX, DSEISINDEX

The seisindex table contains the geographic grids of natural seismicity data in the seisgrid table. The dseisindex table contains the geographic grids of seismicity data in the dseisgrid table. The seisindex table is used by the AEQ application to help identify anomalous events.

TABLE 98: SEISINDEX (DSEISINDEX)

Column Storage Type Description

1 grdname varchar2(6) grid name

2 lat1 float(24) initial latitude

3 lon1 float(24) initial longitude

4 dlat float(24) latitude increment

5 dlon float(24) longitude increment

6 nlat number(8) number of latitudes

7 nlon number(8) number of longitudes

8 orderby varchar2(6) order by (either latitude or longitude)

9 lddate date load date

Category: Automatic Processing Keys: Primary grdname Data: Descriptive grdname, lat1, lon1, dlat, dlon, nlat, nlon, orderby Administrative lddate

Database Schema

156 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

SENSOR

The sensor table contains calibration information for specific sensor channels. This table provides a record of updates in the calibration factor or clock error of each instrument and links a sta/chan/time to a complete instrument response in the table instrument. Waveform data are converted into physical units through multiplication by the calib field located in wfdisc. The correct value of calib may not be accurately known when the wfdisc record is entered into the database. The sensor table provides the mechanism (calratio and calper) to “update” calib, without requiring possibly hundreds of wfdisc records to be updated. Through the foreign key inid, this table is linked to instrument, which has fields pointing to flat files holding detailed calibration information in a variety of formats (see instrument).

TABLE 99: SENSOR

Column Storage Type Description

1 sta varchar2(6) station code

2 chan varchar2(8) channel code

3 time float(53) epoch time of start of recording period

4 endtime float(53) epoch time of end of recording period

5 inid number(8) instrument identifier

6 chanid number(8) channel identifier

7 jdate number(8) Julian date

8 calratio float(24) calibration

9 calper float(24) calibration period

10 tshift float(24) correction of data processing time

11 instant varchar2(1) (y, n) discrete/continuing snapshot

12 lddate date load date

Database Schema

IDC-5.1.1Rev5 October 2002 157 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

Category: Core, Reference Keys: Primary sta/chan/time/endtime Foreign inid, chanid Data: Descriptive sta, chan, instant Measurement time, endtime, jdate, calratio, calper, tshift Administrative lddate

Database Schema

158 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

SITE

The site table contains station location information. Site names and describes a point on the earth where measurements are made (for example, the location of an instrument or array of instruments). It contains information that normally changes infrequently, such as location. In addition, site contains fields that describe the offset of a station relative to an array reference location. Global data integrity implies that the sta/ondate in site be consistent with the sta/chan/ondate in sitechan.

TABLE 100:SITE

Column Storage Type Description

1 sta varchar2(6) station identifier

2 ondate number(8) Julian start date

3 offdate number(8) Julian off date

4 lat float(24) latitude

5 lon float(24) longitude

6 elev float(24) elevation

7 staname varchar2(50) station description

8 statype varchar2(4) station type: single station, array

9 refsta varchar2(6) reference station for array members

10 dnorth float(24) offset from array reference (km)

11 deast float(24) offset from array reference (km)

12 lddate date load date

Category: Core, Reference Keys: Primary sta/ondate Data: Descriptive sta, staname, statype, refsta Measurement ondate, offdate, lat, lon, elev, dnorth, deast Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 159 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

SITE_ADDRESS

The site_address table contains address information not included in the site table.

TABLE 101:SITE_ADDRESS

Column Storage Type Description

1 sta varchar2(6) station name

2 name varchar2(20) expanded station name

3 locality varchar2(40) locality of station

4 stat_prov varchar2(40) state or province

5 country varchar2(40) country name

6 lddate date load date

Category: Reference Keys: Primary sta Data: Descriptive sta, name, locality, stat_prov, country Administrative lddate

Database Schema

160 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

SITEAUX

The siteaux table contains additional site-dependent parameters that are not included in the site table.

TABLE 102:SITEAUX

Column Storage Type Description

1 sta varchar2(6) station code

2 chan varchar2(8) channel code

3 time float(53) epoch time

4 nois float(24) noise amplitude

5 noissd float(24) standard deviation of log noise

6 amcor float(24) amplitude correction

7 amcorsd float(24) correction standard deviation

8 snthrsh float(24) signal/noise detection threshold

9 rely float(24) station reliability

10 ptmcor float(24) P arrival time correction

11 stmcor float(24) S arrival time correction

12 staper float(24) period for measurements

13 auth varchar2(15) author

14 commid number(8) comment identifier

15 lddate date load date

Category: Reference Keys: Primary sta/chan/time Foreign commid Data: Descriptive sta, chan Measurement time, nois, noissd, amcor, amcorsd, snthrsh, rely, ptmcor, stmcor, staper Administrative auth, lddate

Database Schema

IDC-5.1.1Rev5 October 2002 161 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

SITECHAN

The sitechan table contains station-channel information. This table describes the orientation of a recording channel at the site referenced by sta. It provides information about the various channels that are available at a station and maintains a record of the physical channel configuration at a site.

TABLE 103:SITECHAN

Column Storage Type Description

1 sta varchar2(6) station identifier

2 chan varchar2(8) channel identifier

3 ondate number(8) Julian start date

4 chanid number(8) channel identifier

5 offdate number(8) Julian off date

6 ctype varchar2(4) channel type

7 edepth float(24) emplacement depth

8 hang float(24) horizontal angle

9 vang float(24) vertical angle

10 descrip varchar2(50) channel description

11 lddate date load date

Category: Core, Reference Keys: Primary sta/chan/ondate Alternate chanid Data: Descriptive sta, chan, ctype, descrip Measurement ondate, offdate, edepth, hang, vang Administrative lddate

Database Schema

162 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

SITEPOLL

The sitepoll table contains the station and channel names of auxiliary seismic stations that are polled periodically for system monitoring purposes.

TABLE 104:SITEPOLL

Column Storage Type Description

1 sta varchar2(6) station name

2 net varchar2(6) network name

3 chan varchar2(6) channel name

4 lddate date load date

Category: Data Services Keys: Primary sta/net/chan Data: Descriptive sta, net, chan Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 163 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

SPLP

The splp table contains event characterization parameters for short-period/long-period energy ratios. The ratios are computed using the DFX application.

TABLE 105:SPLP

Column Storage Type Description

1 orid number(8) origin identifier

2 sta varchar2(6) station name

3 rectype varchar2(8) recipe type

4 ratio float(24) ratio of short-period to long-period energy

5 lddate date load date

Category: Fundamental Keys: Primary orid/sta Data: Descriptive sta, rectype Measurement ratio Administrative lddate

Database Schema

164 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

SPVAR

The spvar table contains the variance of the detrended log spectrum between fmin and fmax for an arrival identified by arid. The frequency bandwidth is based on a signal-to- noise ratio criterion. Each phase associated with an event has a spvar record.

TABLE 106:SPVAR

Column Storage Type Description

1 arid number(8) arrival identifier

2 fsid number(8) Fourier spectrum identifier

3 acoef float(24) “a” coefficient for nonlinear trend

4 bcoef float(24) “b” coefficient for nonlinear trend

5 ccoef float(24) “c” coefficient for nonlinear trend

6 fmin float(24) minimum frequency

7 fmax float(24) maximum frequency

8 svar float(24) variance of detrended log spectrum

9 lddate date load date

Category: Fundamental Keys: Primary arid/fmin/fmax Foreign fsid Data: Measurement acoef, bcoef, ccoef, fmin, fmax, svar Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 165 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

SREGION

The sregion table contains seismic region numbers and their equivalent descriptions (see [Fli74]).

TABLE 107:SREGION

Column Storage Type Description

1 srn number(8) seismic region number

2 srname varchar2(40) seismic region name

3 lddate date load date

Category: Core, Reference Keys: Primary srn Data: Descriptive srn, srname Administrative lddate

Database Schema

166 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

STAMAG

The stamag table contains station magnitude estimates based upon measurements made on specific seismic phases. Values in stamag are used to calculate network magnitudes stored in netmag.

TABLE 108:STAMAG

Column Storage Type Description

1 magid number(8) magnitude identifier

2 ampid number(8) amplitude identifier

3 sta varchar2(6) station code

4 arid number(8) arrival identifier

5 orid number(8) origin identifier

6 evid number(8) event identifier

7 phase varchar2(8) associated phase

8 delta float(24) station-to-event distance

9 magtype varchar2(6) magnitude type (ml, ms, mb, and so on)

10 magnitude float(24) magnitude

11 uncertainty float(24) magnitude uncertainty

12 magres float(24) magnitude residual

13 magdef varchar2(1) “d” or “n” flag indicating if magnitude is defining or nondefining

14 mmodel varchar2(15) magnitude model

15 auth varchar2(15) author

16 commid number(8) comment identifier

17 lddate date load date

Database Schema

IDC-5.1.1Rev5 October 2002 167 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

Category: Core, Fundamental Keys: Primary magid/ampid/sta Foreign arid, orid, evid, commid Data: Descriptive delta, sta, phase, magtype, magdef, mmodel Measurement magnitude, uncertainty, magres Administrative auth, lddate

Database Schema

168 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

STASSOC

The stassoc table contains summary information about groups of related arrivals. This table defines the group of phases seen at a single station from the same event.

TABLE 109:STASSOC

Column Storage Type Description

1 stassid number(8) stassoc identifier

2 sta varchar2(6) station code

3 etype varchar2(7) event type

4 location varchar2(32) apparent location description

5 dist float(24) estimated distance

6 azimuth float(24) estimated azimuth

7 lat float(24) estimated latitude

8 lon float(24) estimated longitude

9 depth float(24) estimated depth

10 time float(53) estimated origin time

11 imb float(24) estimated mb

12 ims float(24) initial estimated Ms

13 iml float(24) initial estimated ML 14 auth varchar2(15) author

15 commid number(8) comment identifier

16 lddate date load date

Category: Core, Fundamental Keys: Primary stassid Foreign commid Data: Descriptive sta, etype, location Measurement dist, azimuth, lat, lon, depth, time, imb, ims, iml Administrative auth, lddate

Database Schema

IDC-5.1.1Rev5 October 2002 169 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

STD_CHANMAP

The std_chanmap table contains standard channel name mappings between external and internal channel names.

TABLE 110: STD_CHANMAP

Column Storage Type Description

1 ext_chan varchar2(8) external channel name

2 int_chan varchar2(8) internal channel name

3 ondate number(8) Julian start date

4 offdate number(8) Julian off date

5 lddate date load date

Category: Data Services Keys: Primary. ext_chan Foreign. int_chan Data: Descriptive ext_chan, int_chan Measurement ondate, offdate Administrative lddate

Database Schema

170 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

SUBS

The subs table is used by the Subscription Subsystem. It records what email address receives which products. In addition, it tracks the POC for the products.

TABLE 111: SUBS

Column Storage Type Description

1 userid number(8) user identifier

2 intid number(8) internal identifier

3 intidtype varchar2(16) type of intid (usually msgid)

4 subsid number(8) subscription identifier

5 subsname varchar2(24) subscription name

6 prodid number(8) product identifier

7 address varchar2(64) FTP or email address of destination

8 deliv_meth varchar2(6) delivery method (email or ftp)

9 status varchar2(6) either “i,” interactive; or “a,” active

10 ondate date date subscription is “on”

11 offdate date date subscription is “off”

12 initialdate date initial date of subscription

13 lddate date load date

Category: Data Services Keys: Primary userid/prodid Foreign userid, prodid Data: Descriptive intidtype, subsname, deliv_meth, status Measurement intid, subsid, prodid, address, ondate, offdate Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 171 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

SUBSUSER

The subsuser table is used by the Subscription Subsystem to track authorized users of the system. A user is identified by the username and domain from the email header.

TABLE 112: SUBSUSER

Column Storage Type Description

1 userid number(8) user identifier

2 username varchar2(24) user name from the incoming subscription message

3 domain varchar2(48) domain name from the incoming subscription message

4 status varchar2(24) status of this user

5 pocid number(8) point of contact identifier

6 priority number(2) user priority

7 lddate date load date

Category: Data Services Keys: Primary userid Data: Descriptive username, domain, status, pocid, priority Administrative lddate

Database Schema

172 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

THIRDMOM

The thirdmom table contains the third moment of frequency and the percentage of signal frequency amplitudes greater than the corresponding noise frequency amplitudes for an arrival identified by arid. The measurements are used for event screening.

TABLE 113: THIRDMOM

Column Storage Type Description

1 arid number(8) arrival identifier

2 sta varchar2(6) station code

3 rectype varchar2(8) recipe identifier

4 tmf float(24) third moment of frequency

5 tmfpct float(24) percentage of signal spectrum amplitudes greater than noise spectrum amplitudes

6 lddate date load date

Category: Fundamental Keys: Primary arid Data: Descriptive sta, rectype Measurement tmf, tmfpct Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 173 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

TIMEFREQ

The timefreq table contains the time-frequency measurements for event characterization.

TABLE 114: TIMEFREQ

Column Storage Type Description

1 orid number(8) origin identifier

2 sta varchar2(6) station code

3 rectype varchar2(8) recipe identifier

4 zavpct float(24) ratio of bad points to total (vertical)

5 navpct float(24) ratio of bad points to total (north)

6 eavpct float(24) ratio of bad points to total (east)

7 xavpct float(24) ratio of bad points to total (cross-correlation)

8 zavcep float(24) average 2-D cepstrum max (vertical)

9 navcep float(24) average 2-D cepstrum max (north)

10 eavcep float(24) average 2-D cepstrum max (east)

11 zavcor float(24) average autocorrelation (vertical)

12 navcor float(24) average autocorrelation (north)

13 eavcor float(24) average autocorrelation (east)

14 xcor float(24) zero cross-correlation

15 lddate date load date

Category: Fundamental Keys: Primary orid/sta Data: Descriptive sta, rectype Measurement zavpct, navpct, eavpct, xavpct, zavcep, navcep, eavcep, zavcor, navcor, eavcor, xcor Administrative lddate

Database Schema

174 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

TIMESTAMP

The timestamp table is used for scheduling automatic processing of time-series data.

TABLE 115: TIMESTAMP

Column Storage Type Description

1 procclass varchar2(16) process class

2 procname varchar2(16) process name

3 time float(53) last epoch time

4 lddate date load date

Category: Distributed Processing Keys: Primary procclass/procname Data: Descriptive procclass, procname, time Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 175 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

WEIGHTS

The weights table is used to store weighting information for calculating the weights of REB events.

TABLE 116: WEIGHTS

Column Storage Type Description

1 phase varchar2(8) phase type

2 statype varchar2(4) station type (ar or ss)

3 net varchar2(8) unique network identifier

4 tweight float(24) time weight

5 aweight float(24) azimuth weight

6 sweight float(24) slowness weight

7 ondate number(8) Julian start date

8 offdate number(8) Julian off date

9 lddate date load date

Category: Data Services Keys: Primary phase/statype/net Data: Descriptive tweight, aweight, sweight, ondate, offdate Administrative lddate

Database Schema

176 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

WFAUX

The wfaux table contains the length of a waveform file in bytes. The table should have a one-to-one relationship with the wfdisc table for those wfids where a length is required. This table is required by the Continuous Data Acquisition Subsystem to determine the lay- out of a diskloop file and should also provide better access to wfdisc records and better means of determining where and how much data are stored. Routines writing, updating, or deleting from this table should do so simultaneously with wfdisc.

TABLE 117: WFAUX

Column Storage Type Description

1 wfid number(8) waveform identifier

2 length number(10) waveform length, bytes

Category: Fundamental Keys: Primary wfid Data: Descriptive length

Database Schema

IDC-5.1.1Rev5 October 2002 177 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

WFCONV

The wfconv table contains data translations that are to be performed on incoming data before they are written to disk by the DLMan application. Data compression types include “-” if the data are not compressed, or “CA” for Canadian compression. “Type” in columns intype and outtype is the fixed-width data type (for example, “s4”) or “-” if not applicable (that is, if the data are compressed). A “samp” value of zero (0) indicates that the number of samples varies. “Samp” values less than zero in columns insamp and outsamp indicate that the total number of samples must be evenly divisible by –samp. Strip tells whether to strip the authentication headers from the data; “y” means strip them, “n” means do not.

TABLE 118: WFCONV

Column Storage Type Description

1 sta varchar2(6) station code

2 chan varchar2(8) channel code

3 chanid number(8) channel identifier

4 inauth varchar2(1) input authenticated (y or n)

5 incomp varchar2(2) input compression type

6 intype varchar2(2) input fixed-width data type

7 insamp number(8) input samples per packet

8 outauth varchar2(1) output authenticated (y or n)

9 outcomp varchar2(2) output compression type

10 outtype varchar2(2) output fixed-width data type

11 outsamp number(8) output samples per packet

12 strip varchar2(1) data stripped of headers

13 commid number(8) comment identifier

14 lddate date load date

Database Schema

178 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

Category: Data Services Keys: Primary sta/chan Alternate chanid Foreign commid Data: Descriptive sta, chan, inauth, incomp, intype, insamp, outauth, outcomp, outtype, outsamp, strip Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 179 WFDISC, WFPROTO

The wfdisc table contains a waveform header file and descriptive information. This table provides a pointer (or index) to waveforms stored on disk. The waveforms themselves are stored in ordinary disk files called wfdisc or “.w” files as a sequence of sample values (usually in binary representation). Wfproto is a view of the wfdisc table that is used to create temporary wfdisc files for the DLMan application.

TABLE 119: WFDISC (WFPROTO)

Column Storage Type Description

1 sta varchar2(6) station code

2 chan varchar2(8) channel code

3 time float(53) epoch time of first sample in file

4 wfid number(8) waveform identifier

5 chanid number(8) channel operation identifier

6 jdate number(8) Julian date

7 endtime float(53) time + (nsamp-1)/samprate

8 nsamp number(8) number of samples

9 samprate float(24) sampling rate in samples/sec

10 calib float(24) nominal calibration

11 calper float(24) nominal calibration period

12 instype varchar2(6) instrument code

13 segtype varchar2(1) indexing method

14 datatype varchar2(2) numeric storage

15 clip varchar2(1) clipped flag

16 dir varchar2(64) directory

17 dfile varchar2(32) data file IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

TABLE 119: WFDISC (WFPROTO) (CONTINUED)

Column Storage Type Description

18 foff number(10) byte offset of data segment within file

19 commid number(8) comment identifier

20 lddate date load date

Category: Core, Fundamental Keys: Primary sta/chan/time Alternate wfid Foreign chanid, commid Data: Descriptive sta, chan, dir, dfile, foff Measurement time, jdate, endtime, nsamp, samprate, calib, calper, instype, segtype, datatype, clip Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 181 IDC DOCUMENTATION Chapter 2: User Guides

▼ S/H/I Table Descriptions

WFTAG

The wftag table links various identifiers (for example, orid, arid, and stassid to wfid). Linkages can also be determined indirectly using sta, chan, and time. However, it is more efficient to use the wftag table.

TABLE 120:WFTAG

Column Storage Type Description

1 tagname varchar2(8) key (arid, orid, evid, and so on)

2 tagid number(8) tagname value

3 wfid number(8) waveform identifier

4 lddate date load date

Category: Core, Fundamental Keys: Primary tagname/tagid/wfid Data: Descriptive tagname Administrative lddate

Database Schema

182 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 2:

S/H/I Table Descriptions ▼

XTAG

The xtag table links various identifiers (for example, orid, arid, stassid, and wfid to other identifiers). This table is a generalization of the wftag table, which is limited to linking exclusively to the wfid. The thisdb column describes the database account for the record specified by thisid and thisname; thatdb describes the database account for the record specified by thatid and thatname. When a parent/child relationship exists between the records, thisid should designate the parent, and thatid should designate the child.

TABLE 121:XTAG

Column Storage Type Description

1 thisid number(8) thisname identifier

2 thatid number(8) thatname identifier

3 thisname varchar2(8) key for thisid (grid, orid, ntid, and so on)

4 thatname varchar2(8) key for thatid (arid, orid, nfid, and so on)

5 thisdb varchar2(32) database account for the records specified by thisid and thisname

6 thatdb varchar2(32) database account for the records specified by thatid and thatname

7 lddate date load date

Category: Database and Utility Keys: Primary thisid/thisname Data: Descriptive thisid, thatid, thisname, thatname, thisdb, thatdb Administrative lddate

Database Schema

IDC-5.1.1Rev5 October 2002 183

IDC DOCUMENTATION User Guides

Chapter 3: S/H/I Column Descriptions

This chapter describes the columns in the seismic, hydroacoustic, and infrasonic tables used at the PIDC and includes the following topics:

■ Ranges

■ NA Values

■ Columns

Database Schema

IDC-5.1.1Rev5 October 2002 185 IDC DOCUMENTATION User Guides

Chapter 3: S/H/I Column Descriptions

RANGES

Wherever possible, an explicit range is defined for each column. This range is important for data integrity and database management systems that automatically check ranges. When the range consists of a relatively small number of discreet values, the following notation is used:

column ∈ {value-1, value-2, …, value-n}

No range is documented for columns whose value may be any floating point number.

NA VALUES

Sometimes no information is available for a column. In that case, an “NA Value” (for Not Available) is assigned. An NA Value is outside the range of permissible or recommended values for the column. This special NA Value alerts users and applications that the desired column was not available when the record was created. For example, in the origin table, the column ms (surface wave magnitude) may be unknown for a given row. Then the NA Value for magnitudes (–999.0) should be assigned to ms, and msid should be set to –1, the NA Value for msid. Some columns are essential to defining a meaningful record, and they must be specified; the NA Value is not permitted. For example, the column time in arrival must be given a value in the valid range, not an NA Value. Another example is magnitude in netmag and stamag. Magnitude must be given a meaningful value for each record, so no NA Value is defined.

Some general guidelines and specific examples of NA Values are given in Table 122. These are only guidelines and NA values may not be unique to a particular column.

Database Schema

186 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

TABLE 122:GUIDELINES AND EXAMPLES OF NA VALUES

Column Type/Range NA Value Examples

character columns - (hyphen) bmtype, auth

non-negative integers –1 chanid, avid

non-negative real numbers –1.0 cfreq, deltim

real numbers > –999.0 –999.0 iml

large real numbers –9999999999.999, or endtime, time +9999999999.999

An NA Value should not be confused with an ORACLE “NULL.” NA Values are supplied by users, while ORACLE inserts the database value “NULL” when no value is specified. A column containing a database value of “NULL” appears blank when selected within SQL*Plus. When creating a table, a column may be constrained as “NOT NULL” to require the user to supply a value. The ORACLE describe command will identify such columns as “NOT NULL.” No correlation is intended between ORA- CLE “NOT NULL” requirements and IDC requirements that a column must be specified.

COLUMNS

Name: abbrev Table: Glossary Description: Abbreviation name. This is the term used in Origin (Originref, Origin_temp_ga), Explo, and Remark tables in the EXPLOSION database. Format: varchar2(16) External: a16 NA Value: NOT ALLOWED Range: any string up to 16 characters

Database Schema

IDC-5.1.1Rev5 October 2002 187 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: abbrevtype Table: Glossary Description: Abbreviation type. Unique abbreviation identifier: country code, data source, explosion type, and test site. Format: varchar2(16) External: a16 NA Value: - (hyphen) Range: any string up to 16 characters

Name: account Table: Dataready Description: Database account name. The tagid and tagname pointing to the data to be distributed by the Subscription Subsystem are in this database account. Format: varchar2(24) External: a24 NA Value: - (hyphen) Range: any string up to 24 characters

Name: acoef Table: Spvar Description: Coefficient “a” of the quadratic trend of the log spectrum between frequencies fmin and fmax. The spectrum is measured in nm-sec. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: any floating point value

Database Schema

188 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: action Table: Allocate_hour Description: Analyst task performed on this time-block of data. Format: varchar2 (16) External: a16 NA Value: NOT ALLOWED Range: action ∈ {AfterSchock, Allocate, Bull_QC, Del_Pass, RebDone, Scan_Pass}

Name: added Table: Ex_an Description: Number of phases added by an analyst to an expert system event solution. An added phase is an arrival not available to the expert system. Format: number(8) External: i8 NA Value: –1 Range: added ≥ 0

Name: address Table: Alphasite, Subs Description: Internet protocol (IP) address of source of continuous data, for alphasite. FTP, and email address for subs. Format: varchar2(16) for alphasite External: a16 varchar2(64) for subs NA Value: NOT ALLOWED Range: “0.0.0.0” – “255.255.255.255” for alphasite, a valid email address for subs

Database Schema

IDC-5.1.1Rev5 October 2002 189 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: adef Table: Ev_summary (Ex_summary, An_summary) Description: Number of associated nondefining phases. The observations for these phases are not used in the location solution. Format: number(8) External: i8 NA Value: –1 Range: adef ≥ 0

Name: afsid Table: Fsave, Fstag Description: Average Fourier spectrum identifier. Each average spectrum is assigned a unique positive integer identifying it with unique fsid through fstag that are used in generating the average. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: afsid > 0

Name: algorithm Table: Origin (Originref, Origin_temp_ga) Description: Location algorithm used. This column is a brief textual description of the algorithm used for computing a seismic origin. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any string up to 15 characters

Database Schema

190 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: amcor Table: Siteaux Description: Site-dependent log amplitude correction. Format: float(24) External: f10.1 NA Value: –999.0 Range: amcor > –999.0

Name: amcorsd Table: Siteaux Description: Standard deviation for log amplitude correction. Format: float(24) External: f5.2 NA Value: –1.0 Range: amcorsd > 0.0

Name: amp Table: Amplitude, Arrival Description: Measured amplitude defined by amptype. Format: float(24) External: f11.2 NA Value: –1.0 Units: nanometers or dimensionless depending on the type of channel Range: amp > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 191 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: ampid Table: Amplitude, Stamag Description: Amplitude identifier. Every amplitude measure is assigned a unique positive integer that identifies it in the database. If an associated stamag record exists, then ampid links it to amplitude. Format: number(8) External: i8 NA Value: NOT ALLOWED in amplitude –1 in stamag Range: ampid > 0

Name: amplr Table: Apma Description: Maximum 3-component amplitude for all overlapping time windows used in the polarization analysis. This column is equal to the sum of the square roots of the eigenvalues. The only difference between amps and amplr is in the definition of the overlapping time windows. Format: float(24) External: f7.2 NA Value: –1.0 Units: nanometers Range: amplr > 0.0

Name: ampp Table: Apma Description: 3-component amplitude measured at the time of the maximum rectilinearity. This column is equal to the sum of the square roots of the eigenvalues (that is, it is the sum of the amplitudes measured along the three axes of the polarization ellipsoid). Format: float(24) External: f7.2 NA Value: –1.0 Units: nanometers Range: ampp > 0.0

Database Schema

192 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: amps Table: Apma Description: Maximum 3-component amplitude for all overlapping time windows used in the polarization analysis. This column is equal to the sum of the square roots of the eigenvalues. The only difference between amps and amplr is in the definition of the overlapping time windows. Format: float(24) External: f7.2 NA Value: –1.0 Units: nanometers Range: amps > 0.0

Name: amptime Table: Amplitude Description: Epoch time of amplitude measure. Format: float(53) External: f17.5 NA Value: –9999999999.999 Units: seconds Range: any valid epoch time

Name: amptype Table: Ampdescript, Amplitude Description: Amplitude measure descriptor. This descriptor is used to uniquely identify an amplitude measurement and link the description in ampdescript with actual measurements in amplitude. Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: any free-format string up to eight characters

Database Schema

IDC-5.1.1Rev5 October 2002 193 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: antype Table: Origaux Description: Analysis type for this solution. Examples are automatic (a), manual (m), and ground truth (g). Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: antype ∈ {a, m, g}

Name: apmarid Table: Apma Description: Unique apma recipe identifier. Each arrival in apma is assigned a positive integer identifying it with the recipe used in the polarization analysis. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: apmarid > 0

Name: archid Table: Arch_data_type Description: Archive identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: archid > 0

Name: archived Table: Dlfile Description: Status of data archiving; archiving (a), yes (y), or no (n). Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: archived ∈ {a, n, y}

Database Schema

194 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: archiveport Table: Dlman Description: Archiver port. Format: number(6) External: i6 NA Value: –1 Range: 0 ≤ archiveport ≤ 16383

Name: arid Table: Amp3c, Amplitude, Apma, Arrival, Assoc (Assoc_temp_ga), Detection, Fkdisc, Fsdisc, Hydro_assoc, Hydro_features, Infra_features, Spvar, Stamag, Thirdmom Description: Arrival identifier. Each arrival is assigned a unique positive integer identifying it with a unique sta, chan, and time. Format: number(8) External: i8 NA Value: NOT ALLOWED –1 for stamag, fsdisc Range: arid > 0

Name: array Table: Request Description: Array code. Network or station name. Format: varchar2(8) External: a8 NA Value: NOT ALLOWED Range: any string matching the net column in Affiliation (Stanet)

Database Schema

IDC-5.1.1Rev5 October 2002 195 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: asstr Table: Bull_comp Description: Association strength of two events: strong (s) or weak (w). An origin (origin1) is strongly associated with an origin in the other database account (origin2) if three or more defining detections for origin1 are also associated with origin2, or all defining detections for origin1 are also associated with origin2. If events are associated only by time and location (no arrivals available) then asstr is set to w. Format: varchar2(1) External: a1 NA Value: NOT ALLOWED Range: asstr ∈ {s, w}

Name: asta Table: Ev_summary (Ex_summary, An_summary) Description: Number of associated arrivals from regional arrays. “Regional” is currently defined as a station-event distance not less than 250 km and up to 2,000 km. Format: number(8) External: i8 NA Value: –1 Range: asta ≥ 0

Name: attenid Table: Attencoef Description: Attenuation coefficient set identifier. Each set of attenuation coefficients is assigned a unique positive integer to identify the change history. Format: varchar2(20) External: a20 NA Value: - (hyphen) Range: any valid string up to 20 characters

Database Schema

196 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: attribute Table: Na_value Description: Name of the column to which a NA value is to be assigned. Format: varchar2(30) External: a30 NA Value: NOT ALLOWED Range: any string up to 30 characters that is a valid column in this schema

Name: auth Table: Allocate_hour, Amplitude, Apma, Arrival, Discard, Event, Explo, Infra_features, Location, Netmag, Network, Origin (Originref, Origin_temp_ga), Outage, Revaudit, Siteaux, Stamag, Stassoc Description: Author, the originator of the data. Auth may also identify an application generating the record, such as an automated interpretation or signal-processing program. Format: varchar2(15) External: a15 varchar2(16) for allocate_hour NA Value: - (hyphen) Range: any string up to 15 characters

Name: author Table: Fileproduct (Fs_stageproduct) Description: Author of the file product. Format: varchar2(16) External: a16 NA Value: - (hyphen) Range: any string up to 16 characters

Database Schema

IDC-5.1.1Rev5 October 2002 197 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: auxid Table: Outage Description: Auxiliary identification code. Format: varchar2(4) External: a4 NA Value: - (hyphen) Range: any valid auxiliary code up to four characters

Name: available Table: Outage Description: Flag to specify if data are available (t) or unavailable (f). Format: varchar2(1) External: a1 NA Value: NOT ALLOWED Range: available ∈ {t, f}

Name: ave_noise Table: Hydro_features Description: Average pressure of the noise segment. Format: float(24) External: f9.4 NA Value: –1.0 Units: dB re µPa Range: ave_noise > 0.0

Name: avgconstval Table: Qcstats Description: Average value of data in masked constant segments. Format: float(53) External: f17.5 NA Value: –999.0 Units: same as waveform data Range: aveconstval Š 0.0

Database Schema

198 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: avtype Table: Fsave Description: Description of averaged spectrum. This value is used as the channel name. Format: varchar2(8) External: a8 NA Value: NOT ALLOWED Range: avtype ∈ {mean, median, 95 pct, 5 pct}

Name: aweight Table: Weights Description: Azimuth weight. Format: float(24) External: f5.2 NA Value: 0.0 Range: aweight Š 0.0

Name: az1 Table: Hydro_arr_group Description: Azimuth estimated from the time lags of arrivals in a hydro-arrival group. Format: float(24) External: f7.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ az1 < 360.0

Database Schema

IDC-5.1.1Rev5 October 2002 199 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: az2 Table: Hydro_arr_group Description: Azimuth estimated from the time lags of arrivals in a hydro-arrival group. This second azimuth estimate is only needed when only two arrivals exist in a group, which results in an ambiguity between two equally likely azimuths. The error is the same for the two azimuths. Format: float(24) External: f7.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ az2 < 360.0

Name: azcontrib Table: Hydro_assoc Description: Flag that specifies if an arrival that belongs to a hydro arrival group was used to calculate the azimuth. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: azcontrib ∈ {y, n}

Name: azdef Table: Assoc (Assoc_temp_ga) Description: Azimuth-defining code. The one-character flag indicates whether or not the azimuth of a phase was used to constrain the event location solution. This column is defining (azdef = d) if it was used in the location, nondefining (azdef = n) if it was not. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: azdef ∈ {d, n}

Database Schema

200 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: azimuth Table: Arrival, Parrival, Stassoc Description: Observed azimuth. This value is the estimated station-to-event azimuth measured clockwise from North. The estimate is made from f-k or polarization analysis. In stassoc, the value may be an analyst estimate. Format: float(24) External: f7.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ azimuth < 360.0

Name: azres Table: Allow_resid, Assoc (Assoc_temp_ga) Description: Azimuth residual. The value is the difference between the measured station- to-event azimuth for an arrival and the true azimuth. The true azimuth is the bearing to the inferred event origin. Format: float(24) External: f7.1 NA Value: –999.0 Units: degrees Range: –180.0 ≤ azres ≤ 180.0

Database Schema

IDC-5.1.1Rev5 October 2002 201 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: band Table: Instrument Description: Frequency band. The value is a qualitative indicator of frequency passband for an instrument. Values should reflect the response curve rather than just the sample rate. Recommended values are as follows:

s (short-period) m (mid-period) i (intermediate-period) l (long-period) b (broadband) h (high-frequency, very short-period) v (very long-period)

For a better notion of the instrument characteristics, see the instrument response curve. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: band ∈ {s, m, i, l, b, h, v}

Name: bandw Table: Amplitude, Detection, Fkdisc Description: Frequency bandwidth. Format: float(24) External: f7.3 NA Value: –1.0 Units: Hertz Range: bandw > 0.0

Database Schema

202 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: bcoef Table: Spvar Description: Coefficient “b” of the quadratic trend of the log spectrum between frequencies fmin and fmax. The spectrum is measured in nm-sec. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: any floating point value

Name: begin_date Table: Participation Description: Beginning date of station participation in a particular net. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: any valid Julian date (yyyyddd)

Name: belief Table: Assoc (Assoc_temp_ga) Description: Phase identification confidence level. The value is a qualitative estimate of the confidence that a seismic phase is correctly identified. Format: float(24) External: f4.2 NA Value: –1.0 Range: 0.0 ≤ belief ≤ 1.0

Name: bmtyp Table: Detection Description: String indicating a coherent (coh), incoherent (inc), or horizontal (hor) beam type. Format: varchar2(4) External: a4 NA Value: - (hyphen) Range: bmtyp ∈ {coh, inc, hor}

Database Schema

IDC-5.1.1Rev5 October 2002 203 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: bordercolor Table: Mapdisc Description: Map border color name. A solid colored border may appear on the top, bottom, and right of any raster map. Format: varchar2(32) External: a32 NA Value: - (hyphen) Range: any string up to 32 characters that forms a valid X11 color name (for example, black)

Name: calib Table: Wfdisc (Wfproto) Description: Calibration factor. The value is the conversion factor that maps digital data to earth displacement. The factor holds true at the oscillation period specified by the column calper. A positive value means ground motion increasing in component direction (up, north, east) is indicated by increasing counts. A negative value means the opposite. Calib generally reflects the best calibration information available at the time of recording, but refinement may be given in Sen- sor, reflecting a subsequent recalibration of the instrument (see calratio). Format: float(24) External: f16.6 NA Value: NOT ALLOWED Units: nanometers/digital count Range: any nonzero floating point number

Name: calper Table: Sensor, Wfdisc (Wfproto) Description: Calibration period. This gives the period for which calib, ncalib, and calratio are valid. Format: float(24) External: f16.6 NA Value: NOT ALLOWED Units: seconds Range: calper > 0.0

Database Schema

204 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: calratio Table: Sensor Description: Calibration conversion ratio. The value is a dimensionless calibration correction factor that permits small refinements to the calibration correction made using calib and calper from the Wfdisc (Wfproto) table. Often, the wfdisc calib contains the nominal calibration assumed at the time of data recording. If the instrument is recalibrated, calratio provides a mechanism to update calibra- tions from wfdisc with the new information without modifying the wfdisc table. A positive value means ground motion increasing in component direction (up, north, east) is indicated by increasing counts. A negative value means the opposite. Calratio is meant to reflect the most accurate calibration information for the time period for which the sensor record is appropriate, but the nominal value may appear until other information is available. Format: float(24) External: f16.6 NA Value: NOT ALLOWED Range: any nonzero floating point number

Name: ccoef Table: Spvar Description: Coefficient “c” of the quadratic trend of the log spectrum between frequencies fmin and fmax. The spectrum is measured in nm-sec. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: any floating point value

Database Schema

IDC-5.1.1Rev5 October 2002 205 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: cep_delay_time_signal Table: Hydro_features Description: Bubble pulse delay time estimate where the cepstrum is computed from the NSE-detrended spectrum. Format: float(24) External: f9.4 NA Value: –1.0 Units: seconds Range: cep_delay_time_signal > 0.0

Name: cep_delay_time_trend Table: Hydro_features Description: Bubble pulse delay time estimate where the cepstrum is computed from the trend of NSE-detrended spectrum. Format: float(24) External: f9.4 NA Value: –1.0 Units: seconds Range: cep_delay_time_trend > 0.0

Name: cep_peak_std_signal Table: Hydro_features Description: Number of standard deviations from the mean for the largest cepstrum amplitude where the cepstrum is computed from the NSE-detrended spectrum. Format: float(24) External: f9.4 NA Value: –1.0 Units: standard deviations Range: cep_peak_std_signal > 0.0

Database Schema

206 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: cep_peak_std_trend Table: Hydro_features Description: Number of standard deviations from the mean for the largest cepstrum amplitude where the cepstrum is computed with the trend of the NSE-detrended spectrum. Format: float(24) External: f9.4 NA Value: –1.0 Units: standard deviations Range: cep_peak_std_trend > 0.0

Name: cep_var_signal Table: Hydro_features Description: Variance of the cepstrum computed using NSE-detrended spectrum. Format: float(24) External: f9.4 NA Value: –1.0 Units: seconds Range: cep_var_signal > 0.0

Name: cep_var_trend Table: Hydro_features Description: Variance of the cepstrum computed using the trend from the NSE-detrended spectrum. Format: float(24) External: f9.4 NA Value: –1.0 Units: standard deviations Range: cep_var_trend > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 207 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: cfreq Table: Amp3c, Detection, Fkdisc Description: Center frequency of a beam or f-k spectrum. Format: float(24) External: f7.2 NA Value: –1.0 Units: Hertz Range: cfreq > 0.0

Name: chan Table: Amplitude, Arrival, Attencoef, Beamaux, Chan_groups, Detection, Dlfile, Evsc_regional, Fileproduct (Fs_stageproduct), Forbeamaux, Fsdisc, Fwgap, Outage, Producttypesta, Qcstats, Request, Sensor, Siteaux, Sitechan, Sitepoll, Wfconv, Wfdisc (Wfproto) Description: Channel identifier. The value is an eight-character code that specifies a particular channel within a network (station), which, taken together with sta and time, uniquely identifies seismic timeseries data, including the geographic location, spatial orientation, sensor, and subsequent data processing (beam channel descriptor). Format: varchar2(8) External: a8 varchar2(6) for sitepoll NA Value: NOT ALLOWED Range: any lower-case string up to eight characters

Name: chanid Table: Arrival, Dlfile, Fsdisc, Sensor, Sitechan, Wfconv, Wfdisc (Wfproto) Description: Channel recording identifier. The value is a surrogate key used to uniquely identify a specific recording. Chanid duplicates the information of the com- pound key sta, chan, time. Format: number(8) External: i8 NA Value: –1 Range: chanid > 0

Database Schema

208 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: class Table: Chan_groups, Interval, Problem, Request Description: Problem class or object class for interval and request. Format: varchar2(16) External: a16 varchar2(33) for problem NA Value: - (hyphen) Range: any free-format string up to the character limit

Name: clip Table: Amplitude, Arrival, Wfdisc (Wfproto) Description: Clipped data flag. The value is a single-character flag to indicate whether (c) or not (n) the data were clipped. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: clip ∈ {c, n}

Name: clrpth Table: Evsc_prod Description: Hydroacoustic clear-path flag. Set to ‘1’ if all paths within the location error ellipse are clear to at least one hydroacoustic station in a given set. Format: number(1) External: i1 NA Value: –1 Range: clrpth ∈ {0,1}

Database Schema

IDC-5.1.1Rev5 October 2002 209 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: coh_deldur Table: Infra_features Description: Estimated standard deviation in coh_dur. Format: float(24) External: f7.2 NA Value: –1.0 Units: seconds Range: coh_deldur > 0.0

Name: coh_dur Table: Infra_features Description: Time period during which the spatial coherence (reckoned as F-Statistic) “beam” exceeded its threshold for the current time interval of spatial coherence in excess of its threshold value. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: coh_dur > 0.0

Name: coh_per Table: Infra_features Description: Dominant period of the spatially coherent signal. The value is estimated from the inverse of the frequency of the maximum power in a windowed spectrum of the traditional beamformed waveform data during the time interval defined by coinc_time and coh_dur. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: coh_per > 0.0

Database Schema

210 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: coh_snr Table: Infra_features Description: Equivalent, equal channel, coherent signal-to-noise ratio; the inband power in the spatially coherent fraction of the arrival divided by the total inband non- coherent noise. Format: float(24) External: f7.2 NA Value: –1.0 Units: seconds Range: coh_snr > 0.0

Name: coh_time Table: Infra_features Description: Earliest time at which the spatial coherence (determined as F-Statistic) “beam” exceeded its threshold for the current time interval of spatial coherence in excess of its threshold value. Format: float(53) External: f17.5 NA Value: –9999999999.999 Units: seconds Range: coh_time > –9999999999.999

Name: coinc_deldur Table: Infra_features Description: Estimated standard deviation in coinc_dur. Format: float(24) External: f7.2 NA Value: –1.0 Units: seconds Range: coinc_deldur > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 211 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: coinc_dur Table: Infra_features Description: Time period during which both the STA/LTA on the traditional beam and the sample-by-sample F-Statistic beams exceed their respective thresholds for the current time interval of coincidence detection. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: coinc_dur > 0.0

Name: coinc_time Table: Infra_features Description: Earliest time at which the STA/LTA applied to the traditional beam and the spatial coherence “beam” both exceeded their respective thresholds for the current time interval of coincidence detection. Format: float(53) External: f17.5 NA Value: –9999999999.999 Units: seconds Range: coinc_time > –9999999999.999

Name: col_depth Table: Explo Description: Depth of collapse crater. Depth of the deepest point of the collapse crater relative to the original ground surface. Format: float(24) External: f7.4 NA Value: –1 Units: kilometers Range: col_depth Š 0.0

Database Schema

212 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: col_diameter Table: Explo Description: Diameter of collapse crater. Format: float(24) External: f7.4 NA Value: –1 Units: kilometers Range: col_diameter Š 0.0

Name: col_interval Table: Explo Description: Collapse interval. Time interval after shot time of collapse, as determined by geophone and television monitoring. Format: float(24) External: f10.0 NA Value: –1 Units: seconds Range: col_interval Š 0.0

Name: col_volume Table: Explo Description: Volume of collapse crater. Format: float(24) External: f10.7 NA Value: –1 Units: kilometers3 Range: col_volume Š 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 213 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: colormapid Table: Colordisc, Mapcolor Description: Colordisc identifier. Each colordisc is assigned a unique positive integer that identifies it in a database. The colormapid identifies color-lookup tables available to maps. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: colormapid > 0

Name: colormapname Table: Colordisc Description: Colormap name that identifies the color-lookup table in a listing of available tables. Format: varchar2(64) External: a64 NA Value: NOT ALLOWED Range: any string up to 64 characters

Name: colorname Table: Overlaydisc Description: Overlay color name. Format: varchar2(32) External: a32 NA Value: - (hyphen) Range: any valid color name

Database Schema

214 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: command Table: Msgaux Description: Command that was being executed when the failure occurred. If this cannot be determined, such as a caught signal from UNIX, then the value is set to “signal caught.” Format: varchar2(24) External: a24 NA Value: - (hyphen) Range: any string up to 24 characters

Name: commid Table: Allocate_hour, Alphasite, Apma, Arrival, Assoc (Assoc_temp_ga), Channame, Datauser, Detection, Dlfile, Dlman, Event, Explo, Fkdisc, Fsave, Fsdisc, Infra_features, Location, Msgdisc, Netmag, Network, Origerr (Origerr_temp_ga), Origin (Originref, Origin_temp_ga), Outage, Remark, Siteaux, Stamag, Stassoc, Wfconv, Wfdisc (Wfproto) Description: Comment identifier. The value is a key that points to free-form comments entered in the remark table. These comments store additional information about a record in another table. The remark table can have many records with the same commid and different lineno, but the same commid will appear in only one other record among the rest of the tables in the database (see lineno). Format: number(8) External: i8 NA Value: –1 NOT ALLOWED for remark Range: commid > 0

Name: complete Table: Request Description: Percentage complete. Percentage of waveform data acquired for this request. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: 0 ≤ complete ≤ 100

Database Schema

IDC-5.1.1Rev5 October 2002 215 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: complexity Table: Complexity Description: Signal complexity measure estimated by DFX application. Format: float(24) External: f11.4 NA Value: –1.0 Range: complexity ≥ 0.0

Name: conf Table: Origerr (Origerr_temp_ga) Description: Confidence measure for a particular event identification method. Format: float(24) External: f5.3 NA Value: NOT ALLOWED Range: 0.5 ≤ conf ≤ 1.0

Name: connmanport Table: Dlman Description: Connection manager (ConnMan) port number used to send messages to the diskloop manager application. Format: number(6) External: i6 NA Value: 0 Range: 1 ≤ connmanport ≤ 16383

Database Schema

216 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: consider Table: Evsc_prod Description: Flag indicating whether (1) or not (0) an event was considered for screening. Format: number(1) External: i1 NA Value: NOT ALLOWED Units: consider ∈ {0, 1}

Name: const Table: Qcstats Description: Amount of data in the detection processing interval masked due to constant segments. Format: float(53) External: f17.5 NA Value: –999.0 Units: seconds Range: const Š 0.0

Name: constrain_depth Table: Event_control (In_event_control) Description: Logical descriptor that tells location process whether or not to fix (constrain) the current hypocentral depth. If TRUE (1), the depth will be fixed to the value specified on the first (summary) line of the DATA file or as specified by the depth column of the Origin (Originref, Origin_temp_ga) table. If FALSE (0), the depth is an independent solution parameter. Default is TRUE. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: constrain_depth ∈ {0, 1}

Database Schema

IDC-5.1.1Rev5 October 2002 217 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: constrain_latlon Table: Event_control (In_event_control) Description: Logical descriptor that tells location process whether or not to fix (constrain) the current epicentral location. If TRUE (1), the latitude and longitude will be fixed to the value specified by the lat and lon columns of the Origin (Originref, Origin_temp_ga) table. If FALSE (0), the latitude and longitude are independent solution parameters. Default is FALSE. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: constrain_latlon ∈ {0, 1}

Name: constrain_ot Table: Event_control (In_event_control) Description: Logical descriptor that tells location process whether or not to fix (constrain) the current origin time. If TRUE (1), the origin time will be fixed to the value specified by the time column of the Origin (Originref, Origin_temp_ga) table. If FALSE (0), the origin time is an independent solution parameter. Default is FALSE. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: constrain_ot ∈ {0, 1}

Name: controlport Table: Dlman Description: DataControl port. Number used to send commands to the diskloop manager application. Format: number(6) External: i6 NA Value: 0 Range: 0 ≤ controlport ≤ 16383

Database Schema

218 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: country Table: Site_address Description: Full country name for a sensor site. Format: varchar2(40) External: a40 NA Value: - (hyphen) Range: any string up to 40 characters

Name: cov_depth_time Table: Event_control (In_event_control) Description: Coverage ellipse depth/time conversion factor. The value is the conversion factor to be multiplied by the depth and origin time axes (sdepth and stime) of the confidence ellipse to recover the coverage ellipse without having to do a complete relocation. Format: float(24) External: f9.4 NA Value: –999.0 Range: cov_depth_time > 0.0

Name: cov_sm_axes Table: Event_control (In_event_control) Description: Coverage ellipse semi-axis conversion factor. The value is the conversion factor to be multiplied by the semi-major and semi-minor axes of the confidence ellipse to recover the coverage ellipse without having to do a complete relocation. Format: float(24) External: f9.4 NA Value: –999.0 Range: cov_sm_axes > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 219 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: cp_broad_band Table: Evsc_hydro Description: The cep_peak_std_signal from table Hydro_features in the 2–80 Hz band for a given orid/sta pair. Format: float(24) External: f7.2 NA Value: –1.0 Units: standard deviations Range: cp_broad_band > 0.0

Name: crnr_delfreq Table: Infra_features Description: Estimated standard deviation in crnr_freq. Format: float(24) External: f7.2 NA Value: –1.0 Units: Hertz Range: crnr_delfreq > 0.0

Name: crnr_freq Table: Infra_features Description: Corner frequency estimated from a windowed traditional FFT spectrum (ren- dered on a dB power scaling) applied to the traditional beam-formed waveform data. Format: float(24) External: f7.2 NA Value: –1.0 Units: Hertz Range: crnr_freq > 0.0

Database Schema

220 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: ctype Table: Sitechan Description: Channel type. This column specifies the type of data channel: n (normal, a normal instrument response), b (beam, a coherent beam formed with array data), or i (an incoherent beam or energy stack). Format: varchar2(4) External: a4 NA Value: - (hyphen) Range: ctype ∈ {n, b, i}

Name: cycle_size Table: Productcriteria Description: Size to which a subscription product should be allowed to grow before distributing. Format: number(8) External: i8 NA Value: –1 Units: Kilobytes Range: cycle_size > 0

Name: cycle_time Table: Productcriteria Description: Period of cyclicity for a product in the Subscription Subsystem that is how often a product should be delivered. Format: number(4) External: i4 NA Value: –1 Units: Hours Range: cycle_time > 0

Database Schema

IDC-5.1.1Rev5 October 2002 221 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: dasta Table: Ex_an Description: Difference in number of regional array stations contributing to the analyst and expert system origins. The value is [asta (analyst) – asta (expert system)] for analyst versus expert system comparisons or [asta (bulletin1) – asta (bulletin2)] for more general bulletin comparisons. Format: number(8) External: i8 NA Value: –999 Range: dasta > –999

Name: data_info Table: Dataready Description: Miscellaneous data information for the Subscription Subsystem, such as the station name for station processing. Format: varchar2(24) External: a24 NA Value: - (hyphen) Range: any character string up to 24 characters

Name: dataday Table: Rebdone_dataday_flag Description: Julian day of this dataday. Format: number(12) External: i12 NA Value: NOT ALLOWED Range: Julian dates are of the form yyyyddd

Database Schema

222 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: dataid Table: Dataready, Prodtrack Description: Unique identifier for the dataready table. Format: number(8) External: i8 NA Value: –1 Range: dataid ≥ 0

Name: datatype Table: Fsave, Fsdisc, Wfdisc (Wfproto) Description: Numeric data storage. This column specifies the format of a data series in the file system. Data types i4, f4, and s4 are typical values. Datatype i4 denotes a 4-byte integer and f4 denotes a 32-bit real number. s4 is an integer where the most significant byte is in the low address position in memory and is opposite to the i4 order. Machine-dependent formats are supported for common hardware to allow data transfer in native machine binary formats. ASCII formats have also been defined to retain full precision of any binary data type. ASCII may be used when exchanging data between computer systems with incompatible binary types. (See the wfport command manual page for information about converting formats.) Datatype can only describe single values or arrays of one data type. Format: varchar2(2) External: a2 NA Value: - (hyphen) Range: The currently recognized types (lower case is mandatory) are as follows:

a0 = 15-byte ASCII single precision b0 = 24-byte ASCII double precision c0 = 12-byte ASCII integer a# = 15-byte ASCII single precision b# = 24-byte ASCII double precision c# = 12-byte ASCII integer t4 = 4-byte SUN IEEE single precision real t8 = 8-byte SUN IEEE double precision real s4 = 4-byte SUN IEEE integer s2 = 2-byte SUN IEEE short integer f4 = 4-byte VAX IEEE single precision real f8 = 8-byte VAX IEEE double precision real

Database Schema

IDC-5.1.1Rev5 October 2002 223 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

i4 = 4-byte VAX IEEE integer i2 = 2-byte VAX IEEE short integer g2 = 2-byte NORESS gain-ranged

Name: datatype Table: Arch_data_type Description: Data type (or class of data). Format: varchar2(24) External: a24 NA Value: - (hyphen) Range: any string up to 24 characters

Name: datsw Table: Fkdisc Description: A switch to indicate a data format data type. Proper values will be defined through the software libraries and include files. A manual (man) page will explain the meaning of datsw values and reference related software man pages. Format: number(10) External: i10 NA Value: NOT ALLOWED Range: datsw > 0

Name: ddepth Table: Bull_comp, Ex_an Description: Difference in depth between corresponding origin locations. For depth comparisons between analysts and the expert system, the value is [depth (analyst) – depth (expert system)]. For more general bulletin comparisons, the value is [depth (bulletin1) – depth (bulletin2)]. Format: float(24) External: f6.1 NA Value: –999.0 Units: kilometers Range: ddepth > –999.0

Database Schema

224 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: ddepthp Table: Ex_an Description: Difference in the number of defining depth phases associated with analyst and expert system origins. A depth phase is a member of the set, {sP, pP, sS}. The value is: [(number-analyst-phases) – (number-expert-phases)]. Format: number(8) External: i8 NA Value: –999 Range: ddepthp > –999

Name: ddist Table: Bull_comp, Ex_an Description: Difference in distance between corresponding origins in a bulletin comparison. Format: float(24) External: f8.3 NA Value: –1.0 Units: kilometers Range: ddist ≥ 0.0

Name: deast Table: Site Description: Distance east. This column gives the “easting,” or the relative position of an array element east of the location of the array center specified by the value of refsta (see dnorth). Format: float(24) External: f9.4 NA Value: 0.0 Units: kilometers Range: –20,000.0 ≤ deast ≤ 20,000.0

Database Schema

IDC-5.1.1Rev5 October 2002 225 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: delaz Table: Arrival, Detection, Hydro_arr_group Description: Azimuth uncertainty. This column is an estimate of the standard deviation of the azimuth of a signal. Format: float(24) External: f7.2 NA Value: –1.0 Units: degrees Range: delaz > 0.0

Name: deliv_meth Table: Subs Description: Delivery method for subscription products. Format: varchar2(6) External: a6 NA Value: - (hyphen) Range: deliv_meth ∈ {ftp, email, www}

Name: delivid Table: Prodtrack, Productcriteria Description: Identifier that is unique and consecutive for each product constraint. Format: number(8) External: i8 NA Value: –1 Range: delivid ≥ 0

Database Schema

226 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: delslo Table: Arrival, Detection Description: Slowness uncertainty. This column is an estimate of the standard deviation of the slowness of a signal. Format: float(24) External: f7.2 NA Value: –1.0 Units: seconds/kilometers for detection seconds/degree for arrival Range: delslo > 0.0

Name: delta Table: Assoc (Assoc_temp_ga), Evsc_regional, Parrival, Stamag Description: Source-receiver distance. This column is the arc length, over the earth’s surface, of the path the seismic phase follows from source to receiver. The location of the origin is specified in the Origin (Originref, Origin_temp_ga) record referenced by the column orid. The column arid points to the record in the Arrival table that identifies the receiver. The value of the column can exceed 360 degrees. The geographic distance between source and receiver is delta modulo(180). Format: float(24) External: f8.3 NA Value: –1.0 Units: degrees Range: delta ≥ 0.0

Name: deltim Table: Arrival, Detection Description: Arrival time uncertainty. This column is an estimate of the standard deviation of an arrival time. Format: float(24) External: f6.3 NA Value: –1.0 Units: seconds Range: deltim > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 227 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: depdp Table: Origin (Originref, Origin_temp_ga) Description: Depth as estimated from depth phases. The value is a measure of event depth estimated from a depth phase or an average of several depth phases. Depth is measured positive in a downwards direction starting from the earth’s surface (see ndp). Format: float(24) External: f9.4 NA Value: –999.0 Units: kilometers Range: 0.0 ≤ depdp < 1000.0

Name: depth Table: Evsc_prod, Origin (Originref, Origin_temp_ga), Stassoc Description: Source depth. This column gives the depth (positive down) of the event origin. Negative depth implies an atmospheric event. In stassoc, this may be an analyst estimate. Format: float(24) External: f9.4 NA Value: –999.0 Units: kilometers Range: –100.0 ≤ depth < 1000.0 0 ≤ depth < 1000.0 for evsc_prod

Name: depth_conf Table: Producttypeevsc Description: Confidence level of a one-sided confidence interval of the source depth, used for the depth screening criterion. Format: float(24) External: f7.2 NA Value: –999.0 Range: 0 < depth_conf < 1.0

Database Schema

228 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: depth_kvalue Table: Producttypeevsc Description: Depth uncertainty k-value, used to specify additional uncertainty in seismic free-depth solutions. Format: float(24) External: f7.2 NA Value: –999.0 Units: kilometers Range: 0.0 < depth_kvalue < 1000.0

Name: depth_thresh Table: Producttypeevsc Description: Depth screening threshold. An event with a one-sided confidence interval for its source depth that is deeper than this threshold is screened out at the confidence level given by depth_conf. Format: float(24) External: f7.2 NA Value: –999.0 Units: kilometers Range: 0.0 < depth_thresh < 1000.0

Name: deptherr Table: Evsc_prod Description: Depth error. This is the size of the one-sided depth confidence interval used for event screening for a confidence level given by depth_conf in table Pro- ducttypeevsc. A model uncertainty term, given by depth_kvalue in table producttypeevsc, is included for free-depth solutions. Format: float(24) External: f7.2 NA Value: –999.0 Units: kilometers Range: deptherr > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 229 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: depthp Table: Ev_summary (Ex_summary, An_summary) Description: Number of time-defining depth phases. A depth phase is a member of the set {sP, pP, sS}. Format: number(8) External: i8 NA Value: –1 Range: depthp ≥ 0

Name: descr Table: Ampdescript Description: Text description. Describes amplitude measurement parameters. Format: varchar2(255) External: a255 NA Value: - (hyphen) Range: any free-format string up to column size

Name: descrip Table: Glossary, Location, Problem, Ref_loc, Sitechan Description: Text description. Format: varchar2(50) External: a128 varchar2(80) for ref_loc, glossary varchar2(129) for problem NA Value: - (hyphen) Range: any free-format string up to the character limit

Name: dest Table: Mig_rules Description: Destination database for migration. Format: varchar2(10) External: a10 NA Value: NOT ALLOWED Range: any string up to 10 characters that is a valid name of database server

Database Schema

230 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: dest_tbl Table: Mig_rules Description: Destination table for database migration. Format: varchar2(30) External: a30 NA Value: NOT ALLOWED Range: any string up to 30 characters that is a valid table name

Name: detendtime Table: Qcstats Description: End time of actual interval used for detection processing. Format: float(53) External: f17.5 NA Value: –999.0 Units: seconds Range: detendtime < 9999999999.999

Name: dettime Table: Qcstats Description: Start time of actual interval used for detection processing. Format: float(53) External: f17.5 NA Value: –999.0 Units: seconds Range: dettime < 9999999999.999

Name: dfid Table: Dlfile Description: Diskloop file identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: dfid > 0

Database Schema

IDC-5.1.1Rev5 October 2002 231 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: dfile Table: Colordisc, Dlfile, Fileproduct (Fs_stageproduct), Fkdisc, Fsave, Fsdisc, Fwfile, Glossary, Instrument, Mapdisc, Msgdisc, Overlaydisc, Problemlog, Wfdisc (Wfproto) Description: Name of data file. Name of the heap file (fwfile). In fkdisc, the value is the filename of an f-k disk file. In fsdisc, the value is the filename of a Fourier Spec- trum disk file (see dir), and so on. Format: varchar2(32) External: a32 varchar2(65) for problemlog NA Value: NOT ALLOWED Range: any string up to the character limit that conforms to UNIX filename syntax

Name: dfilesize Table: Fwfile Description: Buffer file size for temporary storage of continuous data. Format: number(9) External: i9 NA Value: NOT ALLOWED Range: 0 < dfilesize < disk partition size

Name: did Table: Ex_an Description: Difference in event type between the analyst and expert system origins (see etype). Did is y if the event types are the same or n if the event types are different. Format: varchar2(4) External: a4 NA Value: - (hyphen) Range: did ∈ {y, n}

Database Schema

232 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: digital Table: Instrument Description: Flag denoting whether this instrument record describes an analog (a) or digital (d) recording system. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: digital ∈ {d, a}

Name: dimx Table: Mapdisc Description: Width (or x-dimension) of the map in pixels. Format: number(8) External: i8 NA Value: NOT ALLOWED Units: pixels Range: dimx > 0

Name: dimy Table: Mapdisc Description: Height (or y-dimension) of the map in pixels. Format: number(8) External: i8 NA Value: NOT ALLOWED Units: pixels Range: dimy > 0

Database Schema

IDC-5.1.1Rev5 October 2002 233 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: dir Table: Colordisc, Dlfile, Fileproduct (Fs_stageproduct), Fkdisc, Fsave, Fsdisc, Fwfile, Glossary, Instrument, Mapdisc, Msgdisc, Overlaydisc, Problemlog, Wfdisc (Wfproto) Description: Directory. This column is the directory part of a path name. Relative path names or “.” (dot), the notation for the current directory, may be used. Direc- tory where the heap file is located (fwfile). Directory to find file (msgdisc). Format: varchar2(64) External: a64 varchar2(129) for problemlog NA Value: NOT ALLOWED Range: any string that conforms to UNIX directory name syntax

Name: dist Table: Stassoc Description: Estimated distance. This column gives the approximate source-receiver distance as calculated from slowness (array measurements only), incident angle, or (S–P) times. Format: float(24) External: f7.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ dist ≤ 180.0

Name: dlat Table: Seisindex (Dseisindex) Description: Latitude increment between grid cells in Seisgrid (Dseisgrid). Format: float(24) External: f9.4 NA Value: NOT ALLOWED Units: degrees Range: dlat ≥ 0.0

Database Schema

234 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: dlid Table: Alphasite, Dlfile, Dlman Description: Diskloop manager identification. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: dlid > 0

Name: dlon Table: Seisindex (Dseisindex) Description: Longitude increment between grid cells in Seisgrid (Dseisgrid). Format: float(24) External: f9.4 NA Value: NOT ALLOWED Units: degrees Range: dlon ≥ 0.0

Name: dlsta Table: Ex_an Description: In a comparison of bulletins, dlsta is the difference in the number of local stations contributing to the same event from the corresponding bulletins. The value is [lsta (analyst) – lsta (expert system)] for analyst versus expert system comparisons, and [lsta (bulletin1) – lsta (bulletin2)] for more general bulletin comparisons. Format: number(8) External: i8 NA Value: –999 Range: dlsta > –999

Database Schema

IDC-5.1.1Rev5 October 2002 235 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: dmax Table: Attencoef Description: Maximum distance for which the regional distance correction is applicable. Format: float(24) External: f7.2 NA Value: –999.0 Units: kilometers Range: 0.0 < dmax < 2500.0

Name: dmin Table: Attencoef Description: Minimum distance for which the regional distance correction is applicable. Format: float(24) External: f7.2 NA Value: –999.0 Units: kilometers Range: 0.0 < dmin < 2500.0

Name: dnarr Table: Bull_comp Description: Absolute difference in the number of associated arrivals between corresponding origins. Format: number(8) External: i8 NA Value: –1 Range: dnarr ≥ 0

Database Schema

236 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: dndef Table: Bull_comp, Ex_an Description: Difference in the number of defining phases between corresponding origins. A phase is defining only if its time-component is defining. The value is [ndef (analyst) – ndef (expert system)] for analyst versus expert system comparisons, and [ndef (bulletin1) – ndef (bulletin2)] for more general bulletin comparisons. Format: number(8) External: i8 NA Value: –1 Range: dndef ≥ 0

Name: dnorth Table: Site Description: Distance north. This column gives the “northing,” or relative position of array element north of the array center specified by the value of refsta (see deast). Format: float(24) External: f9.4 NA Value: 0.0 Units: kilometers Range: –20,000.0 ≤ dnorth ≤ 20,000.0

Name: dnsta Table: Ex_an Description: In a comparison of bulletins, dnsta is the difference in the number of contributing stations between the corresponding bulletin locations. The value is [nsta (analyst) – nsta (expert systems)] for analyst versus expert system comparisons, and [nsta (bulletin1) – nsta (bulletin2)] for more general bulletin comparisons. Format: number(8) External: i8 NA Value: –999 Range: dnsta > –999

Database Schema

IDC-5.1.1Rev5 October 2002 237 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: dom_to_send Table: Productcriteria Description: Day of month to send product. Format: number(2) External: i2 NA Value: –1 Range: 0 < dom_to_send ≤ 31

Name: domain Table: Datauser, Subsuser Description: Domain name for a Subscription Subsystem user. Format: varchar2(48) External: a48 NA Value: - (hyphen) NOT ALLOWED for datauser Range: any string up to 48 characters that is a valid internet domain

Name: donetime Table: Rebdone_dataday_flag Description: Epoch time that REB was completed. Format: float(53) External: f17.5 NA Value: NOT ALLOWED Range: any valid epoch time

Name: dow_to_send Table: Productcriteria Description: Day of week to deliver a product. Format: number(2) External: i2 NA Value: –1 Range: 1 ≤ dow_to_send ≤ 7

Database Schema

238 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: dprimp Table: Ex_an Description: In a comparison of bulletins, dprimp is the difference in the number of primary phases between corresponding origins. For a phase to be primary it must be time-defining, a member of the set {P, Pn, Pg, PKP, PKPdf}, and the first arrival at a particular station. The value is [(number-analyst-phases) – (number-expert-phase)] for analyst versus expert-system comparisons and [(number-bulletin1-phases) – (number-bulletin2-phases)] for more general bulletin comparisons. Format: number(8) External: i8 NA Value: –999 Range: dprimp > –999

Name: dropped Table: Qcstats Description: Flag that indicates if the interval was dropped by DFX due to excessive mask- ing. Format: number(8) External: i8 NA Value: –1 Range: dropped ∈ {0, 1}

Name: drsta Table: Ex_an Description: In a comparison of bulletins, drsta is the difference in the number of regional non-array stations contributing to corresponding bulletin origins. The value is [rsta (analyst) – rsta (expert system)] for analyst versus expert-system comparisons or [rsta (bulletin1) – rsta (bulletin2)] for more general bulletin comparisons. Format: number(8) External: i8 NA Value: –999 Range: drsta > –999

Database Schema

IDC-5.1.1Rev5 October 2002 239 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: dscore Table: Evsc_prod Description: Score for the depth event-screening criterion. Format: float(24) External: f7.2 NA Value: –999.0 Range: dscore > –999.0

Name: dsecondp Table: Ex_an Description: In a comparison of bulletins, dsecondp is the difference in the number of secondary phases between corresponding bulletin origins. For a phase to be secondary, it must be defining and cannot be a member of the phase set {P, Pn, Pg, PKP, PKPdf}. The value is [(number-analyst-phases) – (number-expert- phases)] for analyst versus expert-system comparisons, and [(number- bulletin1-phases) – (number-bulletin2-phases)] for more general bulletin comparisons. Format: number(8) External: i8 NA Value: –999 Range: dsecondp > –999

Name: dsize Table: Fileproduct (Fs_stageproduct) Description: Size of data file in bytes. Format: number(10) External: i10 NA Value: NOT ALLOWED Units: bytes Range: 0 < dsize < 99,999,999

Database Schema

240 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: dtime Table: Bull_comp, Ex_an Description: Difference in the origin time between corresponding origins. The value is [time (analyst) – time (expert system)] for analyst versus expert-system comparisons, and [time (bulletin1) – time (bulletin2)] for more general bulletin comparisons. Format: float(24) External: f8.3 NA Value: –999.0 Units: seconds Range: dtime > –999.0

Name: dtsta Table: Ex_an Description: Difference in the number of teleseismic stations (station/event distance > 2000 km) contributing to the analyst and expert system origins. The value is [tsta (analyst) – tsta (expert system)] for analyst versus expert-system comparisons, and [tsta (bulletin1) – tsta (bulletin2) for more general bulletin comparisons. Format: number(8) External: i8 NA Value: –999 Range: dtsta > –999

Database Schema

IDC-5.1.1Rev5 October 2002 241 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: dtype Table: Origin (Originref, Origin_temp_ga) Description: Depth determination flag. This single-character flag indicates the method by which the depth was determined or constrained during the location process. The recommended values are f (free), d (from depth phases), r (restrained by location program) or g (restrained by geophysicist). In cases r or g, either the auth column should indicate the agency or person responsible for this action, or the commid column should point to an explanation in the Remark table. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: dtype ∈ {f, d, r, g}

Name: duration Table: Amplitude Description: Total duration of amplitude window. Combined with start_time, the entire amplitude time window is specified. May also be employed to compute a coda duration magnitude if amp and per columns contain NA values. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: duration ≥ 0

Name: duration Table: Chan_groups Description: Not used. Format: number NA Value: –1 Range: none

Database Schema

242 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: eavcep Table: Timefreq Description: Average maximum value in the two-dimensional cepstrum of the east component traces. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: eavcep ≥ 0

Name: eavcor Table: Timefreq Description: Average autocorrelation along the time axis across all frequencies excluding randomized points of the east component traces. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: eavcor ≥ 0

Name: eavpct Table: Timefreq Description: Average ratio of bad points to total of the east component traces. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: 0 ≤ eavpct ≤ 1

Database Schema

IDC-5.1.1Rev5 October 2002 243 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: edepth Table: Sitechan Description: Emplacement depth. This column gives the depth at which the instrument is positioned, relative to the value of elev in the Site table. Format: float(24) External: f9.4 NA Value: NOT ALLOWED Units: kilometers Range: edepth ≥ 0.0

Name: elev Table: Explo, Location, Site Description: Surface elevation. This column is the elevation of the surface of the earth above a shot point (explo), mine / test site (location), or a seismic station (site) relative to mean sea level. Format: float(24) External: f9.4 NA Value: –999.0 Units: kilometers Range: –10.0 ≤ elev ≤ 10.0

Name: ema Table: Arrival Description: Emergence angle. This column is the emergence angle of an arrival, as observed at a three-component station or array. The value increases from the vertical direction towards the horizontal. Format: float(24) External: f7.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ ema ≤ 90.0

Database Schema

244 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: emaillimit Table: Datauser Description: Maximum size of message that will be delivered via email in the Message Subsystem. Format: number(8) External: i8 NA Value: –1 Units: bytes Range: emaillimit ≥ 0

Name: emailto Table: Msgdest Description: Destination email address. Format: varchar2(64) External: a64 NA Value: - (hyphen) Range: any string up to 64 characters

Name: emares Table: Assoc (Assoc_temp_ga) Description: Emergence angle residual. This column is the difference between an observed emergence angle and the theoretical prediction for the same phase, assuming an event location as specified by the accompanying orid. Format: float(24) External: f7.1 NA Value: –999.0 Units: degrees Range: –90.0 ≤ emares ≤ 90.0

Database Schema

IDC-5.1.1Rev5 October 2002 245 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: end_date Table: Participation Description: Date a station was discontinued from a network. Format: number(8) External: i8 NA Value: –1 Range: any valid Julian date where end_date > begin_date (yyyyddd)

Name: end_time Table: Request Description: Ending time of comparison or processing. Format: float(53) External: f17.5 NA Value: NOT ALLOWED Units: seconds Range: any valid epoch time

Name: endtime Table: Beamaux, Datadays, Fileproduct (Fs_stageproduct), Fwgap, Interval, Outage, Problem, Qcstats, Sensor, Wfdisc (Wfproto) Description: Epoch time. Epochal time is given as seconds and fractions of a second since hour 0 January 1, 1970, and is stored in a double-precision floating number. This represents the ending time of the last gap for the sta/chan pair. Format: float(53) External: f17.5 number(17,5) for problem NA Value: +9999999999.999 Units: seconds Range: endtime < +9999999999.999

Database Schema

246 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: eng_deldur Table: Infra_features Description: Estimated standard deviation in eng_dur. Format: float(24) External: f7.2 NA Value: –1.0 Units: seconds Range: eng_deldur > 0.0

Name: eng_dur Table: Infra_features Description: Time period during which the STA/LTA on the traditional beam exceeded its threshold for the current time interval. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: eng_dur > 0.0

Name: eng_time Table: Infra_features Description: Earliest time at which the STA/LTA applied to the traditional beam exceeded its threshold for the current time interval. Format: float(53) External: f17.5 NA Value: –9999999999.999 Units: seconds Range: eng_time > –9999999999.999

Database Schema

IDC-5.1.1Rev5 October 2002 247 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: eorid Table: Ex_an Description: Expert system origin identifier in an expert system versus analyst origin comparison. Format: number(8) External: i8 NA Value: –1 Range: eorid > 0

Name: epfixf Table: Origaux Description: Flag designating that an epicenter is fixed. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: any alphabetic lower-case character

Name: esaz Table: Assoc (Assoc_temp_ga) Description: Event-to-station azimuth measured in degrees clockwise from North. Format: float(24) External: f7.2 NA Value: –999.0 Units: degrees Range: 0.0 ≤ esaz ≤ 360.0

Name: etype Table: Origin (Originref, Origin_temp_ga), Stassoc Description: Event type. Describes the type of event. Format: varchar2(7) External: a7 NA Value: - (hyphen) Range: etype ∈ {QUAKE, BLAST, EXPL, IND}

Database Schema

248 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: event Table: Origaux Description: Unique event identification (string). Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: any string up to eight characters

Name: evid Table: Discard, Event, Event_control (In_event_control), Explo, Netmag, Origaux, Origin (Originref, Origin_temp_ga), Parrival, Request, Stamag Description: Event identifier. Each event is assigned a unique positive integer that identifies it in a database. Several records in the origin table can have the same evid. Analyst have several opinions about the location of the event. Format: number(8) External: i8 NA Value: –1 NOT ALLOWED for event Range: evid > 0

Name: evname Table: Event Description: Event name. This is the common name of the event identified by evid. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any free-format string up to 15 characters

Database Schema

IDC-5.1.1Rev5 October 2002 249 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: expcode Table: Explo Description: Explosion type code.

A four-character code indicates the type and setting of the explosion as follows: Character 1: Type of explosion. N = nuclear; C = chemical Character 2: Medium. A = air; W = water; U = underground Character 3: Confidence. C = confirmed; P = presumed Character 4: Country. U = U.S.; S = USSR; F = France; C = China; I = India; G = Great Britain; P = Pakistan.

A five-character code is the same as the four-character code, except that a second Country character is added when a second country is involved.

A ten-character code indicates multiple shots (for example, NUCS_SALVO).

A “-” is used for “unknown.” Format: varchar2(10) External: a10 NA Value: - (hyphen) Range: upper case string up to 10 characters long

Name: exptype Table: Explo Description: Explosion type. “Air”, “Airburst”, “Airdrop”, “Balloon”, “Barge”, “Rocket”, “Space”, “Sur- face”, or “Tower” for air explosions. “Tunnel”, “Shaft”, or “Crater” for underground explosions. “Underwater”, or “Water Surface” for water explosions. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any string up to 15 characters long

Database Schema

250 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: ext_chan Table: Exception_chanmap, Std_chanmap Description: External channel identifier. The name of the channel as supplied by the data provider and received by data acquisition software. Format: varchar2(8) External: a8 NA Value: NOT ALLOWED Range: any string up to eight characters

Name: extern_auth Table: Channame Description: The external authority using the station name. Not used for translation. Format: varchar2(20) External: a20 NA Value: - (hyphen) Range: any string up to 20 characters

Name: extern_chan Table: Channame Description: The name of the channel as supplied in the data format frame of the CD-1 protocol. The name is chosen by the data provider. Along with extern_sta, a primary key. Format: varchar2(8) External: a8 NA Value: NOT ALLOWED Range: any string up to eight characters

Database Schema

IDC-5.1.1Rev5 October 2002 251 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: extern_sta Table: Channame Description: The name of the station as supplied in data format frame of the CD-1 protocol. The name is chosen by the data provider. Along with extern_chan, a primary key. Format: varchar2(6) External: a6 NA Value: NOT ALLOWED Range: any upper-case string up to six characters

Name: extmsgid Table: Msgdisc Description: Value of the msgid column in a message that is received by the message system. Format: varchar2(20) External: a20 NA Value: –1 Range: any string up to 20 characters

Name: fileoff Table: Msgdisc Description: Number of bytes to the first character of the email file (first character of the email header). fileoff will always be 0 on the operations system, but will be reset when archived. Format: number(10) External: i10 NA Value: –1 Units: bytes Range: fileoff > 0

Database Schema

252 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: filesize Table: Msgdisc Description: Size of file. Format: number(10) External: i10 NA Value: –1 Units: bytes Range: fileoff > 0

Name: fkid Table: Fkdisc Description: Uniquely identifies a f-k spectrum file. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: fkid > 0

Name: fkqual Table: Detection Description: An integer quantifying the quality of the f-k spectrum. An fkqual = 1 is high quality; an fkqual = 4 is low quality. Format: number(4) External: i4 NA Value: –1 Range: 1 ≤ fkqual ≤ 4

Name: fkrid Table: Fkdisc Description: Uniquely defines a f-k spectrum recipe. Format: number(8) External: i8 NA Value: –1 Range: fkrid > 0

Database Schema

IDC-5.1.1Rev5 October 2002 253 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: fktyp Table: Fkdisc Description: String that identifies the type of f-k spectrum; examples are monochromatic (mono) and broadband (broa). Format: varchar2(4) External: a4 NA Value: NOT ALLOWED Range: any lower-case string up to four characters

Name: fm Table: Arrival Description: First motion. This is a two-character indication of first motion. The first character describes first motion seen on short-period channels and the second holds for long-period instruments. Compression on a short-period sensor is denoted by c, dilatation by a d; and compression on a long-period sensor is denoted by u, dilatation by an r. Empty character positions will be indicated by dots (for example, “.r” for dilatation on a long-period sensor). Format: varchar2(2) External: a2 NA Value: - (hyphen) Range: all two-letter permutations of {c | d | .}, {u | r | .}

Name: fmax Table: Spvar Description: Maximum frequency of a band with snr > 3 dB used for the spectral variance calculation. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Units: Hertz Range: fmax > fmin

Database Schema

254 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: fmin Table: Spvar Description: Minimum frequency of a band with snr > 3 dB used for the spectral variance calculation. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Units: Hertz Range: 0 < fmin < fmax

Name: foff Table: Fileproduct (Fs_stageproduct), Fkdisc, Fsave, Fsdisc, Msgdatatype, Msgdisc, Wfdisc (Wfproto) Description: File offset; the byte offset of a data segment within a physical data file. This column is nonzero if the data reference does not occur at the beginning of the file. Format: number(8) External: i10 number(10) for fileproduct, fkdisc, fsave, fsdisc, msgdisc NA Value: NOT ALLOWED Range: foff ≥ 0

Name: ford Table: Hydro_features, Infra_features Description: Filter order. In infra_features, this column identifies the order of the Infinite Impulse Response (IIR) filter used to extract the spectral band in which the standard fk spectrum calculation was performed. Format: number(8) External: i8 NA Value: 0 Range: ford > 0

Database Schema

IDC-5.1.1Rev5 October 2002 255 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: forid Table: Ex_an Description: Final origin identifier; the origin identification of the analyst orid in an expert system versus analyst origin comparison. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: forid > 0

Name: forwardport Table: Dlman Description: Forwarder port used by the diskloop manager. Format: number(6) External: i6 NA Value: 0 Range: 1 ≤ forwardport ≤ 16383

Name: fpid Table: Fileproduct (Fs_stageproduct) Description: File product identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: fpid > 0

Name: framesize Table: Fwgap Description: Time that each data frame represents. This column is determined from the Data Format Frame of the Alpha Protocol. Format: float(53) External: f17.5 NA Value: –1.0 Range: framesize > 0.0

Database Schema

256 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: freq Table: Apma Description: Center frequency of the wideband polarization analysis. For example, if only the 2 – 4 Hz and 4 – 8 Hz bands satisfy the signal-to-noise ratio criterion, then freq is set to 5.0 Hz. Format: float(24) External: f7.2 NA Value: –1.0 Units: Hertz Range: freq > 0.0

Name: fsdesc Table: Fsrecipe Description: String describing the Fourier spectrum recipe. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any string up to 15 characters

Name: fsid Table: Fsdisc, Fstag, Spvar Description: Fourier spectrum identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED –1 for spvar Range: fsid > 0

Database Schema

IDC-5.1.1Rev5 October 2002 257 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: fsrid Table: Fsdisc, Fsrecipe Description: Fourier spectrum recipe identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: fsrid > 0

Name: fstat Table: Detection Description: F-statistic; a measure of the signal-to-noise ratio at the peak in the f-k spectrum. Format: float(24) External: f5.2 NA Value: –1.0 Range: fstat ≥ 0

Name: fstype Table: Fsave, Fsdisc Description: String specifying the type of Fourier spectrum; for example, amplitude (ampl), phase (phas), complex (comp), and power (powe). Format: varchar2(4) External: a4 NA Value: NOT ALLOWED Range: any lower-case string up to four characters

Name: ftp_address Table: Ftpfailed, Ftplogin Description: FTP address of site from which PIDC is attempting to transfer data message. Format: varchar2(64) External: a64 NA Value: NOT ALLOWED Range: any string up to 64 characters

Database Schema

258 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: ftype Table: Hydro_features Description: Filter type. This indicates the type of filtering that was performed for a Butter- worth filter. “BP” indicates a band-pass filter between low_cut and high_cut; “LP” indicates a low-pass filter below high_cut; “HP” indicates a high-pass filter above low_cut; “BR” indicates a band-reject filter outside low_cut and high_cut. Format: varchar2(2) External: a2 NA Value: - (hyphen) Range: ftype ∈ {BP, LP, HP, BR}

Name: full Table: Dlfile Description: File is full (y/n). full is set to “y” if the diskloop file is full and “n” otherwise. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: full ∈ {n,y}

Name: fwfid Table: Fwfile Description: Identifier of the AlphaForward process that reads from the heap file. Format: number(8) External: i8 NA Value: –1 Range: fwfid > 0

Database Schema

IDC-5.1.1Rev5 October 2002 259 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: fwgid Table: Fwgap Description: Forwarding gap identifier. This identifier is placed into a newly inserted gap record. The value for the counter is retrieved by gdi_get_counter. Format: number(8) External: i8 NA Value: –1 Range: fwgid > –1

Name: fwhid Table: Fwfile Description: Identifier of the AlphaDLHeap process that writes to the heap file. Format: number(8) External: i8 NA Value: –1 Range: fwhid > 0

Name: fzp Table: Hydro_features Description: Filter causality. This flag indicates zero-phase filtering. If it is 1, the filter is zero-phase (noncausal); if it is 0, the filter is not zero-phase (causal). Format: number(8) External: i1 NA Value: NOT ALLOWED Range: fzp ∈ {0,1}

Database Schema

260 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: gap Table: Origaux Description: Gap in azimuthal coverage. Format: number(4) External: i3 NA Value: –1 Units: degrees Range: 0 ≤ gap ≤ 360

Name: gctp1 through gctp15 Table: Mapdisc Description: General cartographic transformation package variable. The default for all values is 0. Format: float(24) External: f10.4 NA Value: NOT ALLOWED Range: see mapdisc man page

Name: grdname Table: Seisgrid (Dseisgrid), Seisindex (Dseisindex) Description: Name for identifying the basis of a natural seismicity grid. Format: varchar2(6) External: a6 NA Value: NOT ALLOWED Range: any free-format string up to six characters

Database Schema

IDC-5.1.1Rev5 October 2002 261 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: grn Table: Ev_summary (Ex_summary, An_summary), Gregion, Origin (Originref, Origin_temp_ga) Description: Geographic region number, as defined by [Fli74]. Format: number(8) External: i8 NA Value: –1 Range: grn > 0

Name: grname Table: Gregion Description: Geographic region name. This column is the common name of a geographic region, as given in [Fli74]. Names may have changed due to changing political circumstances (for example, old RHODESIA = new ZIMBABWE) (see grn and srname). Format: varchar2(40) External: a40 NA Value: NOT ALLOWED Range: any upper-case string up to 40 characters

Name: grpname Table: Producttypeevsc Description: Group name for subscriptions. Format: varchar2(24) External: a24 NA Value: - (hyphen) Range: any valid string up to 24 characters

Database Schema

262 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: gvhi Table: Ampdescript Description: High group velocity for determining a time window. This column defines the start time of an amplitude measurement window if toff is null. If gvhi is used, then gvlo must be used to define the end time of the window. Format: float(24) External: f5.2 NA Value: –999.0 Units: kilometers/second Range: gvhi > gvlo

Name: gvlo Table: Ampdescript Description: Low group velocity for determining a time window. This column defines the end time of an amplitude measurement window if tlen is null or if gvhi is used to define the start time of the window. Format: float(24) External: f5.2 NA Value: –999.0 Units: kilometers/second Range: gvlo > 0

Name: hamp Table: Amp3c Description: Horizontal amplitude. Absolute maximum amplitude (nm) measured on the root of the sum of the squares of two horizontally-oriented components filtered in a frequency band centered at cfreq Hz. Format: float(24) External: f11.2 NA Value: –999.0 Units: nanometers Range: hamp ≥ 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 263 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: hang Table: Sitechan Description: Horizontal orientation of seismometer. This column specifies the orientation of the seismometer in the horizontal plane, measured clockwise from North. For a North-South orientation with the seismometer pointing toward the north, hang = 0.0; for East-West orientation with the seismometer pointing toward the west, hang = 270.0 (see vang). Format: float(24) External: f6.1 NA Value: NOT ALLOWED Units: degrees Range: 0.0 ≤ hang ≤ 360.0

Name: header_fpid Table: Fpdescription Description: fpid pointing to the header row for this product type. Format: number(8) External: i8 NA Value: –1 Range: header_fpid > 0

Name: high_cut Table: Hydro_features Description: High-cut frequency of filter. Format: float(24) External: f9.4 NA Value: –1.0 Units: Hertz Range: 0.0 ≤ high_cut ≤ sample rate/2

Database Schema

264 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: hmxmn Table: Apma 1/2 Description: Maximum-to-minimum horizontal amplitude ratio defined as (λ1/λ2) where λ1 and λ2 are the maximum and minimum eigenvalues obtained by solving the 2-D eigensystem using only the horizontal components. This S-type value is calculated at the time of maximum 3-component amplitude. Format: float(24) External: f7.2 NA Value: –1.0 Range: hmxmn ≥ 0.0

Name: hour Table: Allocate_hour Description: Starting hour of a time block for interactive analysis. Format: number(2) External: i2 NA Value: NOT ALLOWED Units: hours Range: 0 ≤ hour ≤ 23

Name: hour_to_send Table: Productcriteria Description: Hour at which the product is to be sent. Format: number(2) External: i2 NA Value: NOT ALLOWED Units: hours Range: 0 ≤ hours_to_send ≤ 23

Database Schema

IDC-5.1.1Rev5 October 2002 265 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: hscore Table: Evsc_prod Description: Score for the hydroacoustic event-screening criterion. Format: float(24) External: f7.2 NA Value: –999.0 Range: hscore > –999.0

Name: hsnr Table: Amp3c Description: Horizontal signal-to-noise ratio. Ratio of hamp to the root-mean-square amplitude of the root of the sum of the squares of two horizontallyoriented components filtered in a frequency band centered at cfreq Hz. Format: float(24) External: f10.2 NA Value: –999.0 Range: hsnr ≥ 0.0

Name: htov Table: Amp3c Description: Horizontal-to-vertical power ratio. One-half times the square of the ratio of hamp to vamp. Format: float(24) External: f10.2 NA Value: –999.0 Range: htov ≥ 0.0

Database Schema

266 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: hvrat Table: Apma Description: Horizontal-to-vertical power ratio defined as

(C3 + C2)/2C1

where C1, C2, and C3 are the diagonal elements of the covariance matrix (C1 corresponds to the vertical component). This is an S-phase-type value that is calculated at the time of the maximum 3-component amplitude. Format: float(24) External: f7.2 NA Value: –1.0 Range: hvrat ≥ 0.0

Name: hvratp Table: Apma Description: Horizontal-to-vertical power ratio defined as

(C3 + C2)/2C1

where C1, C2, and C3 are the diagonal elements of the covariance matrix (C1 corresponds to the vertical component). This is a P-phase-type value that is calculated at the time of maximum rectilinearity. Format: float(24) External: f7.2 NA Value: –1.0 Range: hvratp ≥ 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 267 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: hydro_cp_thresh Table: Producttypeevsc Description: Threshold of the hydroacoustic cepstral peak screening criterion. Format: float(24) External: f7.2 NA Value: –999.0 Units: dB re µPa Range: 0.0 < hydro_cp_thresh < 999.0

Name: hyd_grp_phase Table: Hydro_arr_group Description: Flag that indicates if the interval was dropped by DFX due to excessive mask- ing. Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: any string up to eight characters; currently hyd_grp_phase ∈ {H, T, N}

Name: hydro_id Table: Hydro_arr_group, Hydro_assoc Description: Identifier which is the primary key in the hydro_arr_group table and the foreign key in hydro_assoc. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: hydro_id > 0

Database Schema

268 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: hydro_te_thresh Table: Producttypeevsc Description: Threshold of the hydroacoustic total energy screening criterion. Format: float(24) External: f7.2 NA Value: –999.0 Units: dB re µPa Range: 0.0 < hydro_te_thresh < 999.0

Name: icell Table: Seisgrid (Dseisgrid) Description: Grid cell index. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: icell > 0

Name: id Table: Ga_tag Description: Arrival or origin identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: id > 0

Name: idate Table: Msgdisc Description: Initial Julian date message that was received. Format: number(8) External: i8 NA Value: –1 Range: any valid Julian date

Database Schema

IDC-5.1.1Rev5 October 2002 269 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: ident Table: Origaux Description: Identifier assigned to an origin by an external source in an incoming origin data message. Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: any string up to eight characters

Name: imb Table: Stassoc Description: Initial body wave magnitude. This column is an analyst’s estimate of the body wave magnitude using data from a single station (see iml, ims, magnitude, magtype, mb, ml, and ms). Format: float(24) External: f7.2 NA Value: –999.0 Range: imb > –2.0

Name: imethod Table: Msgdisc Description: Method of transmission for a message. Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: imethod ∈ {email, ftp}

Database Schema

270 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: iml Table: Stassoc Description: Initial local magnitude. This column is an analyst’s estimate of the local using data from a single station (see imb, ims, magnitude, magtype, mb, ml, and ms). Format: float(24) External: f7.2 NA Value: –999.0 Range: iml > –2.0

Name: ims Table: Stassoc Description: Initial surface wave magnitude. The value in this column is an analyst’s estimate of surface wave magnitude using data from a single station (see iml, imb, magnitude, magtype, mb, ml, and ms). Format: float(24) External: f7.2 NA Value: –999.0 Range: ims > –2.0

Name: inang1 Table: Apma

Description: Apparent incidence angle (measured from the vertical) of the eigenvector (e1) associated with the largest eigenvalue (λ1). This column is also called the long-axis incidence angle or the emergence angle. This P-type value is calculated at the time of maximum rectilinearity. Format: float(24) External: f7.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ inang1 < 90.0

Database Schema

IDC-5.1.1Rev5 October 2002 271 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: inang3 Table: Apma

Description: Apparent incidence angle (measured from the vertical) of the eigenvector (e3) associated with the smallest eigenvalue (λ3). This column is also called the short-axis incidence angle. This S-type value is measured at the time of the maximum 3-component amplitude. Format: float(24) External: f7.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ inang3 < 90.0

Name: inarrival Table: Amplitude Description: Flag to indicate whether or not amp is the same as it is in the Arrival table. Format: varchar2(1) External: a1 NA Value: NOT ALLOWED Range: inarrival ∈ {y, n}

Name: inauth Table: Wfconv Description: Flag showing if input data are authenticated. Format: varchar2 (1) External: a1 NA Value: - (hyphen) Range: inauth ∈ {y, n}

Database Schema

272 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: incomp Table: Wfconv Description: Input data compression type. The only type currently supported is Canadian compression (CA). Format: varchar2(2) External: a2 NA Value: - (hyphen) Range: incomp ∈ {CA}

Name: inid Table: Instrument, Sensor Description: Instrument identifier. This column is a unique key to the instrument table and inid provides the only link between sensor and instrument. Format: number(8) External: i8 NA Value: NOT ALLOWED –1 for sensor. Range: inid > 0

Name: initialdate Table: Subs Description: Initial date of a subscription. Format: date External: a17 NA Value: NOT ALLOWED Range: any valid ORACLE date

Name: inloop Table: Dlfile Description: File is part of a diskloop (y/n). Format: varchar2(1) External: a1 NA Value: NOT ALLOWED Range: inloop ∈ {n, y}

Database Schema

IDC-5.1.1Rev5 October 2002 273 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: insamp Table: Wfconv Description: Number of input samples per packet. Format: number(8) External: i8 NA Value: 0 Range: insamp > 0

Name: insname Table: Instrument Description: Instrument name. This character string contains the name of the instrument. Format: varchar2(50) External: a50 NA Value: - (hyphen) Range: any free-format string up to 50 characters

Name: instant Table: Sensor Description: Snapshot indicator. When instant = y, the snapshot was taken at the time of a discrete procedural change, such as an adjustment of the instrument gain; when instant = n, the snapshot is of a continuously changing process, such as calibration drift. This value is important for tracking time corrections and cal- ibrations. The default value is y. Format: varchar2(1) External: a1 NA Value: NOT ALLOWED Range: instant ∈ {y, n}

Database Schema

274 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: instype Table: Instrument, Wfdisc (Wfproto) Description: Instrument type. This character string is used to indicate the instrument type. Some examples are: SRO, ASRO, DWWSSN, LRSM, and S-750. Format: varchar2(6) External: a6 NA Value: - (hyphen) Range: upper-case instrument type

Name: int_chan Table: Exception_chanmap, Std_chanmap Description: Internal channel identifier. The name of a channel that was historically stored in the archive database. Format: varchar2(8) External: a8 NA Value: NOT ALLOWED Range: any string up to eight characters

Name: intern_chan Table: Channame Description: The name of the channel as chosen by the data consumer. The translation is from extern_chan to intern_chan. Format: varchar2(8) External: a8 NA Value: NOT ALLOWED Range: any lower-case string up to eight characters

Database Schema

IDC-5.1.1Rev5 October 2002 275 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: intern_chanid Table: Channame Description: The chanid corresponding to the intern_sta, intern_chan. Foreign key into the Sitechan table. Format: number(8) External: i8 NA Value: –1 Range: intern_chanid > 0

Name: intern_sta Table: Channame Description: The name of the station as chosen by the data consumer. The translation is from extern_sta to intern_sta. Format: varchar2(6) External: a6 NA Value: NOT ALLOWED Range: any upper-case string up to six characters

Name: intid Table: Msgdisc, Subs Description: Internal identifier for message tracking. Format: number(8) External: i8 NA Value: –1 Range: intid > 0

Name: intidtype Table: Msgdisc, Subs Description: Identifier type for the intid. Format: varchar2(16) External: a16 NA Value: - (hyphen) Range: any valid identifier in the schema

Database Schema

276 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: intvlid Table: Interval Description: Interval identifier. Each interval is assigned a unique positive integer that identifies it in the database. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: intvlid > 0

Name: intype Table: Wfconv Description: Input fixed width datatype. Format: varchar2(2) External: a2 NA Value: - (hyphen) Range: same as datatype

Name: inwfactivity Table: Chan_groups Description: Not used. Format: number(1) NA Value: –1 Range: none

Database Schema

IDC-5.1.1Rev5 October 2002 277 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: iphase Table: Arrival Description: Reported phase. This eight-character column holds the name initially given to a seismic phase. Standard seismological labels for the types of signals (or phases) are used (for example, P, PKP, PcP, pP). Both upper- and lower-case letters are available and should be used when appropriate, for example, pP or PcP (see phase). Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: any string up to eight characters that conforms to seismological practice

Name: isrc Table: Msgdisc Description: Initial source of message. Format: varchar2(64) External: a64 NA Value: - (hyphen) Range: any string up to 64 characters

Name: itime Table: Msgdest, Msgdisc Description: Initial time when message was received. Format: float(53) External: f17.5 NA Value: –9999999999.999 Units: seconds Range: any valid epoch time

Database Schema

278 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: jdate Table: Allocate_hour, Arrival, Datadays, Detection, Fkdisc, Fsdisc, Origin (Originref, Origin_temp_ga), Qcstats, Scan_date, Sensor, Wfdisc (Wfproto) Description: Julian date; date of an arrival, origin, seismic recording, and so on. The same information is available in epoch time, but the Julian date format is more con- venient for many types of searches. Dates B.C. are negative. The year will never equal 0000, and the day will never equal 000. Where only the year is known, the day of the year is 001; where only year and month are known, the day of year is the first day of the month. Only the year is negated for B.C., so 1 January of 10 B.C. is –0010001 (see time). Format: number(8) External: i8 NA Value: –1 Range: Julian dates are of the form yyyyddd; must be consistent with the accompanying time column

Name: kbscause Table: Ex_an Description: Obsolete column. Format: varchar2(7) External: a7 NA Value: - (hyphen) Range: any free-format string up to seven characters

Name: keyname Table: Lastid (Problastid, Rms_lastid) Description: Identifier type. This column contains the actual name of a key whose last assigned numeric value is saved in keyvalue. Format: varchar2(15) External: a15 NA Value: NOT ALLOWED Range: keyname ∈ {arid, chanid, commid, evid, inid, orid, stassid, wfid, dataid, prodid, subsid, and so on}

Database Schema

IDC-5.1.1Rev5 October 2002 279 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: keyvalue Table: Lastid (Problastid, Rms_lastid) Description: Current identifier value. This column maintains the last assigned value (a positive integer) of the counter for the specified keyname. The keyvalue is the last counter value used for the column keyname. Key values are maintained in the database to ensure uniqueness. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: keyvalue > 0

Name: kurtosis Table: Hydro_features Description: Kurtosis of the estimated signal energy between onset_time and termination_time. Format: float(24) External: f9.4 NA Value: –9999999999.999 Range: –10000000.0 < kurtosis< 10000000.0

Name: label Table: Mapdisc Description: Header for Map listing. A label, such as world, categorizes each Map. Label is used to build a sorted list of maps in the Map program. Format: varchar2(65) External: a65 NA Value: - (hyphen) Range: any string up to 65 characters

Database Schema

280 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: last_mig_date Table: Mig_date Description: Last date of database migration. Format: date External: a17 NA Value: NOT ALLOWED Range: any valid ORACLE date

Name: lastfailedtime Table: Ftpfailed Description: Time of most recent attempt to retrieve data message by FTP. Format: float(53) External: f17.5 NA Value: NOT ALLOWED Range: any valid epoch time

Name: lat Table: Location, Mappoint, Origin (Originref, Origin_temp_ga), Ref_loc, Site, Stassoc Description: Geographic latitude. Locations north of the equator have positive latitudes. Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: –90.0 ≤ lat ≤ 90.0

Name: lat1 Table: Seisindex (Dseisindex) Description: Southern-most latitude of the first grid cell in Seisgrid (Dseisgrid). Format: float(24) External: f9.4 NA Value: NOT ALLOWED Units: degrees Range: –90.0 ≤ lat1 ≤ 90.0

Database Schema

IDC-5.1.1Rev5 October 2002 281 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: latmajor Table: Mapdisc Description: Latitude interval for displaying major grid lines in the Map application. Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: 0.0 < latmajor < 90.0

Name: latminor Table: Mapdisc Description: Latitude interval for displaying minor grid lines in the Map application. Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: 0 < latminor < 90.0

Name: latorigradians Table: Mapdisc Description: Latitude origin radians. Coordinates in radians of the lower left corner in the Map application. The Map application uses this for mercator projections only. Format: float(24) External: f9.4 NA Value: –999.0 Units: radians Range: –π/2 < latorigradians < π/2

Name: lddate Table: Affiliation (Stanet), Allocate_hour, Allow_resid, Alphasite, Amp3c, Ampdescript, Amplitude, Apma, Arch_data_type, Arrival, Assoc (Assoc_temp_ga), Attencoef, Bull_comp, Ceppks, Chan_groups, Channame, Colordisc, Complexity, Datadays, Dataready, Datauser, Detection, Discard,

Database Schema

282 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Dlfile, Dlman, Ev_summary (Ex_summary, An_summary), Event, Event_control (In_event_control), Evsc_hydro, Evsc_prod, Evsc_regional, Ex_an, Exception_chanmap, Explo, Fileproduct (Fs_stageproduct), Fkdisc, Fpdescription, Fsave, Fsdisc, Fsrecipe, Fstag, Ftpfailed, Ftplogin, Fwfile, Fwgap, Fwsite, Glossary, Gregion, Hydro_arr_group, Hydro_assoc, Hydro_features, Infra_features, Instrument, Interval, Lastid (Problastid, Rms_lastid), Mapcolor, Mapdisc, Mapover, Mappoint, Mig_date, Location, Msgaux, Msgdatatype, Msgdest, Msgdisc, Netmag, Network, Origaux, Origerr (Origerr_temp_ga), Origin (Originref, Origin_temp_ga), Outage, Overlaydisc, Parrival, Participation, Problem, Problemlog, Problemmail, Prodtrack, Productcriteria, Producttypeevsc, Rebdone_dataday_flag, Ref_loc, Regcoef, Remark, Request, Revaudit, Seisgrid (Dseisgrid), Seisindex (Dseisindex), Sensor, Site, Site_address, Siteaux, Sitechan, Sitepoll, Splp, Spvar, Sregion, Stamag, Stassoc, Std_chanmap, Subs, Subsuser, Thirdmom, Timefreq, Timestamp, Weights, Wfconv, Wfdisc (Wfproto), Wftag, Xtag Description: Load date. The date and time the record was inserted into the database. For the bull_comp table, lddate is the date of the comparison. Format: date External: a17 NA Value: NOT ALLOWED Range: any valid ORACLE date

Name: length Table: Dlfile, Wfaux Description: Length of file, bytes (dlfile), waveform length, bytes (wfaux). Format: number(10) External: i10 NA Value: NOT ALLOWED Units: bytes Range: length > 0

Name: lg_snr Table: Evsc_regional Description: Signal-to-noise ratio of the Lg measurement. Format: float(24) External: f7.2 NA Value: –999.0 Range: lg_snr > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 283 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: lineno Table: Remark, Glossary Description: Line number. This integer is assigned as a sequence number for multiple line comments. Format: number(8) External: i8 number(4) for glossary NA Value: NOT ALLOWED Range: lineno > 0

Name: loc_all_stas Table: Event_control (In_event_control) Description: Logical descriptor that informs the location process whether or not it should use only stations with source-dependent corrections in event locations. If TRUE (1), use all stations in event location. If FALSE (0), only use phase data from stations possessing either an SSSC, SRST, or test-site correction. Any data without a valid correction will not be included in the final event location. Only meaningful if src_dpnt_corr is > 0. Default is TRUE. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: loc_all_stas ∈ {0, 1}

Name: loc_alpha_only Table: Event_control (In_event_control) Description: Logical descriptor that restricts phase data to be used in event location to only those stations contained in the substation list. If FALSE (0), use all stations provided in the Site table. If TRUE (1), only “PRIMARY” station data are used to locate events. This is option desirable in cases where the station network has varying station qualities contributing to events. Default is FALSE. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: loc_alpha_only ∈ {0, 1}

Database Schema

284 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: loc_conf Table: Producttypeevsc Description: Confidence level of location error ellipse used to assess whether the error ellipse was onshore, offshore or mixed (in other words, partially onshore and offshore). Format: float(24) External: f7.2 NA Value: –999.0 Range: 0.0 < loc_conf < 1.0

Name: loc_dist_varwgt Table: Event_control (In_event_control) Description: Logical descriptor that informs the location process if predefined distance variance weighting should be applied to the event location. The predefined weighting is a set of data variances as a function of distance. If FALSE (0) and both user_var_wgt and srst_var_wgt are also set to FALSE, then variances are determined by the deltim, delslo, and delaz from Arrival. Default is FALSE. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: loc_dist_varwgt ∈ {0, 1}

Name: loc_sdv_mult Table: Event_control (In_event_control) Description: Large residual multiplier factor. This column is only meaningful when loc_sdv_screen is set to TRUE (1). If TRUE, all data with travel-time/azimuth/ slowness residuals greater than this factor times its data variance (standard error) will be ignored during any given iteration of the location process. Default is 3.0. Format: float(24) External: f5.2 NA Value: NOT ALLOWED Range: loc_sdv_mult > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 285 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: loc_sdv_screen Table: Event_control (In_event_control) Description: Logical descriptor that tells the location process whether or not to ignore data with travel-time/azimuth/slowness residuals greater than loc_sdv_mult times its data standard error in determining an event location. If FALSE (0), include data regardless of its residuals, provided it meets other pertinent conditions. Default is FALSE. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: loc_sdv_screen ∈ {0, 1}

Name: loc_src_dpnt_reg Table: Event_control (In_event_control) Description: Source-dependent region identifier for event location. If source-dependent corrections are applied as part of event location process (src_dpnt_corr > 0), then loc_src_dpnt_reg indicates region name. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any free-format string up to 15 characters

Name: locality Table: Site_address Description: Geographical location within a country. Format: varchar2(40) External: a40 NA Value: - (hyphen) Range: any string up to 40 characters

Database Schema

286 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: location Table: Stassoc Description: Location description. This character string describes the location of an event identified from data recorded at a single station. An examples is Fiji- Tonga. Format: varchar2(32) External: a32 NA Value: - (hyphen) Range: any free-format string up to 32 characters

Name: locid Table: Location, Explo Description: Location identification code. Format: varchar2(30) External: a30 NA Value: - (hyphen) Range: any valid string up to 30 characters

Name: locname Table: Location Description: Location name. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any valid string up to fifteen characters

Database Schema

IDC-5.1.1Rev5 October 2002 287 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: logat Table: Arrival Description: Log of amplitude divided by period. This measurement of signal size is often reported instead of the amplitude and period separately. This column is only filled if the separate measurements are not available. Format: float(24) External: f7.2 NA Value: –999.0 Units: log (nanometers/seconds) Range: logat > 0.0

Name: login Table: Problem, Problemlog, Problemmail Description: Login name of originator of log entry or a mail subscriber. Format: varchar2(33) External: a32 NA Value: NOT ALLOWED Range: any valid string up to 33 characters that is a valid email address

Name: lon Table: Location, Mappoint, Origin (Originref, Origin_temp_ga), Ref_loc, Site, Stassoc Description: Geographic longitude. Longitudes are measured positive east of the Green- wich meridian. Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: –180.0 ≤ lon ≤ 180.0

Database Schema

288 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: lon1 Table: Seisindex (Dseisindex) Description: Western-most longitude of the first grid cell in Seisgrid (Dseisgrid). Format: float(24) External: f9.4 NA Value: NOT ALLOWED Units: degrees Range: –180.0 ≤ lon1 ≤ 180.0

Name: lonmajor Table: Mapdisc Description: Longitude interval (in degrees) for displaying major grid lines in the Map application. Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: 0 < lonmajor < 180.0

Name: lonminor Table: Mapdisc Description: Longitude interval (in degrees) for displaying minor grid lines in the Map application. Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: –180.0 < lonminor < 180.0

Database Schema

IDC-5.1.1Rev5 October 2002 289 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: lonorigradians Table: Mapdisc Description: Longitude origin radians. Coordinates in radians of the lower left corner in the Map application. Map uses this for mercator projections only. Format: float(24) External: f9.4 NA Value: –999.0 Units: radians Range: −π ≤ latorigradians ≤ π

Name: low_cut Table: Hydro_features Description: Low-cut frequency of filter. Format: float(24) External: f9.4 NA Value: –1.0 Units: Hertz Range: low_cut > 0.0

Name: lsta Table: Ev_summary (Ex_summary, An_summary) Description: Number of local arrival times associated with an event. “Local” is currently defined as a station-event distance of less than 250 km. Format: number(8) External: i8 NA Value: –1 Range: lsta > 0

Database Schema

290 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: machine Table: Dlfile, Dlman, Fwsite Description: Fully qualified domain name of the computer where the connection manager resides. Format: varchar2(32) External: a32 NA Value: - (hyphen) Range: any string up to 32 characters that points to a valid machine

Name: mag_all_stas Table: Event_control (In_event_control) Description: Logical descriptor that informs magnitude process whether or not it should only use amplitude information from stations with magnitude test-site corrections. If TRUE (1), use all amplitude information in event magnitudes. If FALSE (0), use only amplitude data from stations possessing a magnitude test-site correction; any data without a valid correction will not be included in the magnitude determination. Only meaningful if mag_test_site is not null or “-.” Default is TRUE. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: mag_all_stas ∈ {0, 1}

Name: mag_alpha_only Table: Event_control (In_event_control) Description: Logical descriptor that restricts amplitude data to be used in the magnitude determination to only those stations contained in the substation list. If FALSE (0), use all valid amplitudes. If TRUE (1), only “Primary seismic” station data are used for the magnitude calculation. This option is desirable in cases where the station network has varying station qualities contributing to the magnitude. Default is FALSE. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: mag_alpha_only ∈ {0, 1}

Database Schema

IDC-5.1.1Rev5 October 2002 291 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: mag_sdv_mult Table: Event_control (In_event_control) Description: Magnitude large residual multiplier factor. This column is meaningful only when mag_sdv_screen is set to TRUE (1). If TRUE, an amplitude with magnitude residuals greater than this factor times its data variance (standard error) will be ignored by the magnitude process. Default is 3.0. Format: float(24) External: f5.2 NA Value: NOT ALLOWED Range: mag_sdv_mult > 0.0

Name: mag_sdv_screen Table: Event_control (In_event_control) Description: Logical descriptor that tells magnitude process whether or not to ignore amplitude data with magnitude residuals greater than mag_sdv_mult times its data standard error in determining the given magnitude. If FALSE (0), include data regardless of its residuals, provided it meets other pertinent conditions. Default is FALSE. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: mag_sdv_screen ∈ {0, 1}

Name: mag_src_dpnt_reg Table: Event_control (In_event_control) Description: Source-dependent region identifier for magnitude determination. If source- dependent corrections are applied as part of the event magnitude determination process, then mag_src_dpnt_reg indicates the region name. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any free-format string up to 15 characters

Database Schema

292 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: magdef Table: Stamag Description: Magnitude defining switch. A one-character flag indicating whether or not a station magnitude for a given stamag record was used in determining the network magnitude. This column is defining (magdef = d) if it is used in network magnitude calculation or nondefining (magdef = n) if it is not used. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: magdef ∈ {d, n}

Name: magid Table: Netmag, Stamag Description: Network magnitude identifier. This value is assigned to identify a network magnitude in the netmag table. This column is required for every network magnitude. Magnitudes given in Origin (Originref, Origin_temp_ga) must reference a network magnitude with magid = mbid, mlid or msid, whichever is appropriate (see mbid, mlid, or msid). Format: number(8) External: i8 NA Value: NOT ALLOWED Range: magid > 0

Name: magnitude Table: Netmag, Stamag Description: Magnitude. This column gives the magnitude value of the type indicated in magtype. The value is derived in a variety of ways, which are not necessarily linked directly to an arrival (see imb, iml, ims, magtype, mb, ml, and ms). Format: float(24) External: f7.2 NA Value: NOT ALLOWED –999.0 for netmag Units: magnitude Range: magnitude > –2.0

Database Schema

IDC-5.1.1Rev5 October 2002 293 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: magpref_mb Table: Producttypeevsc

Description: mb magnitude type used for screening (see Netmag.magtype). Default is mb_ave. Format: varchar2(6) External: a6 NA Value: NOT ALLOWED

Range: any mb magnitude type up to six characters

Name: magpref_ms Table: Producttypeevsc

Description: Ms magnitude type used for screening (see Netmag.magtype). Default is ms_ave. Format: varchar2(6) External: a6 NA Value: NOT ALLOWED

Range: any Ms magnitude type up to six characters

Name: magres Table: Stamag Description: Magnitude residual. This column is the difference between the magnitude for a given stamag record and the network magnitude. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: –10.0 < magres < 10.0

Database Schema

294 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: magth Table: Seisgrid (Dseisgrid) Description: Magnitude threshold used to calculate the number of events per year in each grid cell. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: any valid magnitude value

Name: magtype Table: Netmag, Producttypeorigin, Seisgrid (Dseisgrid), Stamag Description: Magnitude type, for example, mb. Format: varchar2(6) External: a6 varchar2(4) for producttypeorigin NA Value: NOT ALLOWED Range: any magnitude type up to six characters

Name: mapfiletype Table: Mapdisc Description: Specifies how the Map program handles the referenced Map file. If mapfiletype = all, then the program reads the file in its entirety. If mapfiletype = blk, then the program reads only the blocks necessary for the display area. Format: varchar2(4) External: a4 NA Value: NOT ALLOWED Range: mapfiletype ∈ {all, blk}

Database Schema

IDC-5.1.1Rev5 October 2002 295 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: mapid Table: Mapcolor, Mapdisc, Mapover Description: Mapdisc identifier. Each mapdisc is assigned a unique positive integer that identifies it in a database. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: mapid > 0

Name: mapname Table: Mapdisc Description: Name of the map. Each map in the Map application is assigned a name for identifying the map in a list of all maps. Format: varchar2(64) External: a64 NA Value: NOT ALLOWED Range: any string up to 64 characters

Name: maptype Table: Mapdisc Description: Type of map. A positive integer enumerator for identifying the output graphic type, either raster or vector (maptype = 1 for raster and maptype = 2 for vector). Format: number(8) External: i8 NA Value: NOT ALLOWED Range: maptype ∈ {1, 2}

Database Schema

296 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: masked Table: Qcstats Description: Amount of data in the processing interval masked due to point-spikes, spikes, or constant value segments. Format: float(53) External: f17.5 NA Value: –999.0 Units: seconds Range: masked ≥ 0

Name: maxdelta Table: Allow_resid Description: Maximum station to event distance. Format: float(24) External: f8.3 NA Value: –1.0 Units: degrees Range: maxdelta ≥ 0.0

Name: maxdep_err Table: Producttypeorigin Description: Maximum of depth_error product constraint. Format: float(24) External: f9.4 NA Value: 999.0 Units: kilometers Range: mindeperr < maxdep_err < 999.0

Database Schema

IDC-5.1.1Rev5 October 2002 297 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: maxdepth Table: Producttypeorigin Description: Maximum depth value for a product constraint. Format: float(24) External: f9.4 NA Value: 999.0 Units: kilometers Range: mindepth < maxdepth < 999.0

Name: maxdist Table: Origaux Description: Distance to farthest station. Format: float(24) External: f6.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ maxdist ≤ 180.0

Name: maxesd Table: Producttypeorigin Description: Maximum distance between the event and a station. Format: float(24) External: f6.2 NA Value: –1 Units: degrees Range: minesd ≤ maxesd ≤ 180.0

Database Schema

298 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: maxf Table: Fsave, Fsdisc Description: Maximum frequency. Frequency of the last sample in a Fourier spectrum. Format: float(24) External: f9.4 float(9) for fsave NA Value: –1.0 Units: Hertz Range: maxf > 0.0

Name: maxkx Table: Fkdisc Description: Maximum wavenumber along x-axis in an f-k spectrum. F-k spectra are assumed to be symmetrical, ranging from –maxkx to maxkx. Format: float(24) External: f7.4 NA Value: –1.0 (Either maxkx or maxsx must be set.) Units: kilometers-1 Range: maxkx > 0.0

Name: maxky Table: Fkdisc Description: Maximum wavenumber along y-axis of an f-k spectrum. F-k spectra are assumed to be symmetrical, ranging from –maxky to maxky. Format: float(24) External: f7.4 NA Value: –1.0 (Either maxky or maxsy must be set.) Units: kilometers-1 Range: maxky > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 299 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: maxlat Table: Producttypeorigin, Producttypesta Description: Maximum latitude. Locations north of the equator have positive latitude. Format: float(24) External: f9.4 NA Value: 999.0 Units: degrees Range: –90.0 ≤ maxlat ≤ 90.0

Name: maxlon Table: Producttypeorigin, Producttypesta Description: Maximum longitude. Locations east of the Greenwich Meridian have positive longitude. Format: float(24) External: f9.4 NA Value: 999.0 Units: degrees Range: –180.0 ≤ maxlon ≤ 180.0

Name: maxmag Table: Producttypeorigin Description: Maximum value of magnitude for a product constraint. Format: float(24) External: f7.2 NA Value: 999.0 Units: magnitude Range: minmag < maxmag < 999.0

Database Schema

300 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: maxmb_ms Table: Producttypeorigin

Description: Maximum value of mb – Ms. Format: float(24) External: f7.2 NA Value: 999.0 Units: magnitude Range: minmb_ms < maxmb_ms < 999.0

Name: maxsx Table: Fkdisc Description: Maximum slowness along the x-axis in a broadband f-k spectrum. F-k spectra are assumed to be symmetrical, ranging from –maxsx to maxsx. Format: float(24) External: f7.4 NA Value: –1.0 (Either maxkx or maxsx must be set.) Units: seconds/kilometer Range: maxsx > 0.0

Name: maxsy Table: Fkdisc Description: Maximum slowness along the y-axis in a broadband f-k spectrum. F-k spectra are assumed to be symmetrical, ranging from –maxsy to maxsy. Format: float(24) External: f7.4 NA Value: –1.0 (Either maxsy or maxky must be set.) Units: seconds/kilometer Range: maxsy > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 301 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: maxtime Table: Fwfile Description: Greatest time period that a gap in the data can span. Format: float(53) External: f17.5 NA Value: –999.0 Units: seconds Range: maxtime > 0

Name: mb Table: Evsc_prod, Origin (Originref, Origin_temp_ga)

Description: Body wave magnitude, mb. (origin) This is the body wave magnitude of an event. The identifier mbid that points to magid in the Netmag table is associated with this column. The information in that record summarizes the method of analysis and data used (see imb, iml, ims, magnitude, magtype, ml, and ms). (evsc_prod) Body wave magnitude for event screening. The type of measurement is indicated by magtype_mb. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: mb > –2.0

Name: mb_err Table: Producttypeevsc

Description: Uncertainty of single-station mb magnitude estimates, used in the computation of the confidence interval of the network estimate of mb minus Ms. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: 0.0 < mb_err < 10.0

Database Schema

302 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: mb_max_dist Table: Event_control (In_event_control)

Description: Body wave magnitude (mb) station magnitudes at distances greater than mb_max_dist will not be used in network magnitude calculations. Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: 0.0 ≤ mb_max_dist ≤ 180.0

Name: mb_min_dist Table: Event_control (In_event_control)

Description: Body wave magnitude (mb) station magnitudes at distances less than mb_min_dist will not be used in network magnitude calculations. Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: 0.0 ≤ mb_min_dist ≤ 180.0

Name: mbid Table: Origin (Originref, Origin_temp_ga) Description: Magnitude identifier for mb. This column stores the magid for a record in Net- mag. Mbid is a foreign key joining origin to netmag where origin.mbid = netmag.magid (see magid, mlid, and msid). Format: number(8) External: i8 NA Value: –1 Range: mbid > 0

Database Schema

IDC-5.1.1Rev5 October 2002 303 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: mbms Table: Evsc_prod

Description: Difference of body and surface wave magnitudes, mb minus Ms, including a slope term given by mbms_slope of table Producttypeevsc. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: mbms > –999.0

Name: mbms_conf Table: Producttypeevsc

Description: Confidence level for the mb minus Ms screening criterion. This confidence level is for a one-sided confidence interval for mb minus Ms. Format: float(24) External: f7.2 NA Value: –999.0 Range: 0.0 < mbms_conf < 1.0

Name: mbms_slope Table: Producttypeevsc

Description: Slope term (A) for the mb minus Ms relation (Amb – Ms) to account for calibration of magnitude dependence of the screening criterion. The standard default value is 1.25. A typical range of reasonable values is from +1.0 to +2.0. Format: float(24) External: f7.2 NA Value: –999.0 Range: 0.0 < mbms_slope < 999.0

Database Schema

304 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: mbms_thresh Table: Producttypeevsc

Description: Threshold for the mb minus Ms screening criterion. Events with one-sided confidence intervals for mb minus Ms (Amb – Ms, including the slope term) less than this threshold are screened out at the confidence level given by mbms_conf. Typical values of this threshold range from +1.0 to +4.0, depending on the slope term given by mbms_slope. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: 0.0 < mbms_thresh < 999.0

Name: mbmserr Table: Evsc_prod

Description: Error of mb minus Ms. This is the size of the one-sided confidence interval used for the mb minus Ms screening criterion for a confidence level given by mbms_conf of table Producttypeevsc. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: mbmserr > –999.0

Name: mean_arrival_time Table: Hydro_features Description: Mean arrival time of the estimated signal energy, in epoch time. Format: float(53) External: f17.5 NA Value: NOT ALLOWED Units: seconds Range: any valid epoch time

Database Schema

IDC-5.1.1Rev5 October 2002 305 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: medium Table: Explo Description: Explosion shot medium. Format: varchar2(48) External: a48 NA Value: - (hyphen) Range: any lower-case string up to 48 characters

Name: merge_adjacent Table: Arch_data_type Description: Merge flag. If y, Archive should merge adjacent rows. Format: varchar2(2) External: a2 NA Value: - (hyphen) Range: merge_adjacent ∈ {y, n}

Name: mfoff Table: Msgdisc Description: Offset in bytes to beginning of message. Format: number(10) External: i10 NA Value: –1 Units: bytes Range: mfoff > 0

Name: min_dp_snr_pp Table: Producttypeevsc Description: Minimum pP depth phase signal-to-noise ratio required for depth phase analysis. Format: float(24) External: f7.2 NA Value: –999.0 Range: 0 < min_dp_snr_pp < 999

Database Schema

306 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: min_dp_snr_sp Table: Producttypeevsc Description: Minimum sP depth phase signal-to-noise ratio required for depth phase analysis. Format: float(24) External: f7.2 NA Value: –999.0 Range: 0 < min_dp_snr_sp < 999

Name: min_dt_pp Table: Evsc_prod Description: pP–P travel-time difference at nearest station beyond 25 deg. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: 0 < min_dt_pp < 999

Name: min_dt_sp Table: Evsc_prod Description: sP–P travel-time difference at nearest station beyond 25 deg. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: 0 < min_dt_sp < 999

Database Schema

IDC-5.1.1Rev5 October 2002 307 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: min_mb Table: Producttypeevsc

Description: Minimum mb magnitude for application of event-screening criteria. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: min_mb > –999.0

Name: min_moveout_pp Table: Producttypeevsc Description: Minimum (pP–P) travel time moveout required for the depth screening criterion to be applied to depth-phase solutions. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: –999.0 < min_moveout_pp < 999.0

Name: min_moveout_sp Table: Producttypeevsc Description: Minimum (sP–P) travel time moveout required for the depth screening criterion to be applied to depth-phase solutions. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: –999.0 < min_moveout_sp < 999.0

Database Schema

308 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: min_ndef Table: Producttypeevsc Description: Minimum number of defining phases required for the event-screening criteria to be applied to a seismic-acoustic event. Format: number(8) External: i8 NA Value: –1 Range: min_ndef > 0

Name: min_ndp_pp Table: Producttypeevsc Description: Minimum number of pP depth phases required for the depth screening criterion to be applied to depth-phase solutions. Format: number(8) External: i8 NA Value: –1 Range: min_ndp_pp > 0

Name: min_ndp_sp Table: Producttypeevsc Description: Minimum number of sP depth phases required for the depth screening criterion to be applied to depth-phase solutions. Format: number(8) External: i8 NA Value: –1 Range: min_ndp_sp > 0

Database Schema

IDC-5.1.1Rev5 October 2002 309 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: min_nsta_ms Table: Producttypeevsc

Description: Minimum number of stations required to contribute to the network Ms estimate for the mb minus Ms screening criterion to be applied. Format: number(8) External: i8 NA Value: –1 Range: 0 < min_nsta_ms < 1000

Name: min_wdepth Table: Evsc_prod Description: Minimum depth of water within the location error ellipse defined by smaj_sc, smin_sc, and strike. Format: float(24) External: f7.2 NA Value: –999.0 Units: meters Range: min_wdepth > 0.0

Name: min_wdepth_thresh Table: Producttypeevsc Description: Minimum water depth threshold for application of the hydroacoustic screening criteria. Format: float(24) External: f7.2 NA Value: –999.0 Units: kilometers Range: 0.0 < min_wdepth_thresh < 10.0

Database Schema

310 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: mindelta Table: Allow_resid Description: Minimum station to event distance. Format: float(24) External: f8.3 NA Value: –1.0 Units: degrees Range: mindelta ≥ 0.0

Name: mindep_err Table: Producttypeorigin Description: Minimum value of depth_error constraint. Format: float(24) External: f9.4 NA Value: –999.0 Units: kilometers Range: –999.0 < mindep_err < maxdep_err

Name: mindepth Table: Producttypeorigin Description: Minimum depth product constraint. Format: float(24) External: f9.4 NA Value: –999.0 Units: kilometers Range: –999.0 < mindepth < maxdepth

Database Schema

IDC-5.1.1Rev5 October 2002 311 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: mindist Table: Origaux Description: Distance to closest station. Format: float(24) External: f6.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ maxdist ≤ 180.0

Name: minesd Table: Producttypeorigin Description: Minimum distance between an event and stations. Format: float(24) External: f6.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ minesd ≤ maxesd

Name: minlat Table: Producttypeorigin, Producttypesta Description: Minimum latitude. Locations north of the equator have positive latitude. Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: –90.0 ≤ minlat ≤ 90.0

Database Schema

312 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: minlon Table: Producttypeorigin, Producttypesta Description: Minimum longitude defining a reference area. Locations east of the Green- wich Meridian have positive longitude. Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: –180.0 ≤ minlon ≤ 180.0

Name: minmag Table: Producttypeorigin Description: Minimum value of the magnitude constraint. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: –999.0 < minmag < maxmag

Name: minmb_ms Table: Producttypeorigin

Description: Minimum value of mb – Ms product constraint. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: –999.0 < minmb_ms < maxmb_ms

Database Schema

IDC-5.1.1Rev5 October 2002 313 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: missing Table: Qcstats Description: Amount of missing data in the interval. Format: float(53) External: f17.5 NA Value: NOT ALLOWED Units: seconds Range: masked < 9999999999.999

Name: ml Table: Origin (Originref, Origin_temp_ga)

Description: Local magnitude (ML) of an event. The identifier mlid, which points to magid in the Netmag table, is associated with this column. The information in that record summarizes the method of analysis and the data used (see imb, iml, ims, magnitude, magtype, mb, and ms). Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: ml > –2.0

Name: mlid Table: Origin (Originref, Origin_temp_ga) Description: Magnitude identifier for ml. This column stores the magid for a record in Net- mag. Mlid is a foreign key joining origin to netmag, where table.mlid = table.magid (see magid, msid, and mbid). Format: number(8) External: i8 NA Value: –1 Range: mlid > 0

Database Schema

314 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: mmodel Table: Event_control (In_event_control), Stamag Description: Magnitude model. This character string identifies the magnitude model employed for station (stamag) or overall network magnitude calculation (event_control). In stamag, mmodel is the unique magnitude model as extracted from the magnitude correction file. In event_control, mmodel indicates only whether or not mixed models were employed (mixed) or a unique magnitude model was used for all stations. In the latter case, it would be identical to stamag.mmodel. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any free-format string up to 15 characters

Name: modauthor Table: Request Description: Author of last state change. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any string up to 15 characters

Name: moddate Table: Interval Description: Modification date. The date and time the record was last updated (state column) in the database. Format: date External: a17 NA Value: NOT ALLOWED Range: any valid ORACLE date

Database Schema

IDC-5.1.1Rev5 October 2002 315 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: modtime Table: Request Description: Modification time. The epoch time that the record was last updated in the database. Format: float(53) External: f17.5 NA Value: NOT ALLOWED Units: seconds Range: any valid epoch time

Name: moist Table: Explo Description: Moisture content of explosion shot-point medium. Format: float(24) External: f5.2 NA Value: –1 Units: 1/100% Range: moist ≤ 1.0

Name: moveout_pp Table: Evsc_prod Description: Moveout of (pP–P) travel times for seismic stations between 25 and 100 degrees from an event. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: moveout_pp > –999.0

Database Schema

316 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: moveout_sp Table: Evsc_prod Description: Moveout of (sP–P) travel times for seismic stations between 25 and 100 degrees from an event. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: moveout_sp > –999.0

Name: mpdescrip Table: Mappoint Description: Arbitrary string describing the referenced geographic point. Format: varchar2(50) External: a50 NA Value: - (hyphen) Range: any string up to 50 characters

Name: mplabel Table: Mappoint Description: String used as a label for the geographic point described by a record in the mappoint table (for example, Paris, London, K8, and so on). Format: varchar2(65) External: a65 NA Value: - (hyphen) Range: any string up to 65 characters

Database Schema

IDC-5.1.1Rev5 October 2002 317 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: mptype Table: Mappoint Description: String specifying the type of geographic point described by a record in the mappoint table. Examples include cities, mines, and so on. Format: varchar2(20) External: a20 NA Value: - (hyphen) Range: any free-format (spaces allowed) string up to 20 characters

Name: ms Table: Evsc_prod, Origin (Originref, Origin_temp_ga) Description: Surface wave magnitude. Format: (origin) This is the surface wave magnitude for an event. The identifier msid, which points to magid in the Netmag table, is associated with this column. The information in that record summarizes the method of analysis and the data used (see imb, iml, ims, magnitude, magtype, mb, and ml). (evsc_prod) Surface wave magnitude for event screening. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: ms > –2.0

Name: ms_err Table: Producttypeevsc

Description: Uncertainty of single-station Ms magnitude estimates used in the computation of the confidence interval of the network estimate of mb minus Ms. Format: float(24) External: f7.2 NA Value: –999.0 Units: magnitude Range: 0.0 < ms_err < 10.0

Database Schema

318 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: mscore Table: Evsc_prod

Description: Score for the mb minus Ms event-screening criterion. Format: float(24) External: f7.2 NA Value: –999.0 Range: mscore > –999.0

Name: msgdformat Table: Fpdescription, Msgdatatype Description: General format of the data that follows. Format: varchar2(16) External: a16 NA Value: NOT ALLOWED Range: any string up to 16 characters

Name: msgdid Table: Msgdest Description: Message destination identifier. Format: number(8) External: i8 NA Value: –1 Range: msgdid > 0

Name: msgdtype Table: Fpdescription, Msgdatatype Description: Data type of a data section within an AutoDRM message. Format: varchar2(16) External: a16 NA Value: NOT ALLOWED Range: any string up to 16 characters that is a recognized data type

Database Schema

IDC-5.1.1Rev5 October 2002 319 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: msgid Table: Ftpfailed, Msgaux, Msgdatatype, Msgdest, Msgdisc, Prodtrack Description: Message identifier. In msgdest, this column is the message identifier of the response message created by AutoDRM. Format: number(8) External: i8 NA Value: –1 Range: msgid > 0

Name: msgrow Table: Msgaux Description: Number of lines in a message. Format: number(4) External: i4 NA Value: –1 Units: lines Range: msgrow > 0

Name: msgsrc Table: Msgdisc Description: Source code from where the message was sent. Format: varchar2(16) External: a16 NA Value: - (hyphen) Range: any string up to 16 characters

Name: msgtype Table: Datauser, Msgdisc Description: Message type. Format: varchar2(16) External: a16 NA Value: - (hyphen) Range: any string up to 16 characters

Database Schema

320 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: msgver Table: Msgdisc Description: Message Subsystem version number. Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: any string up to eight characters

Name: msid Table: Origin (Originref, Origin_temp_ga) Description: Magnitude identifier for ms. This column stores the magid for a record in Net- mag. Msid is a foreign key joining origin to netmag, where table.msid = table.magid (see magid, mlid, and mbid). Format: number(8) External: i8 NA Value: –1 Range: msid > 0

Name: msize Table: Msgdatatype, Msgdisc Description: Size of bytes of message or section of a message. Format: number(8) External: i8 number(10) for msgdisc NA Value: –1 Units: bytes Range: msize > 0

Database Schema

IDC-5.1.1Rev5 October 2002 321 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: mtype Table: Ampdescript Description: Measurement type. This column defines how the amplitude is measured in a given time window. The following values are allowed: peak (maximum amplitude), stav (maximum short-term average amplitude), rms (root- mean-squared amplitude), peak2tr (maximum peak-to-trough amplitude), and 1stpeak (first motion amplitude). Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: mtype ∈ {peak, stav, rms, peak2tr, 1stpeak}

Name: multev Table: Ex_an Description: Indicates whether or not another analyst event solution is within 50 km and 5 minutes of the analyst event (for example, multiple event). Format: varchar2(4) External: a4 NA Value: - (hyphen) Range: multev ∈ {y, n}

Name: na_value Table: Na_value Description: Value to be inserted for a column when no other value is available. Format: varchar2(30) External: a30 NA Value: NOT ALLOWED Range: any string up to 30 characters that is valid for that column

Database Schema

322 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: name Table: Chan_groups, Explo, Fpdescription, Interval, Site_address Description: Name of a constant, variable, or parameter. Format: varchar2(20) External: a20 varchar2(16) for chan_groups varchar2(32) for explo varchar2(64) for fpdescription NA Value: - (hyphen) Range: any string up to (16, 20, 32, 64) characters

Name: narr1 Table: Bull_comp Description: Number of associated arrivals for orid1. Format: number(8) External: i8 NA Value: –1 Range: narr1 ≥ 0

Name: narr2 Table: Bull_comp Description: Number of associated arrivals for orid2. Format: number(8) External: i8 NA Value: –1 Range: narr2 ≥ 0

Database Schema

IDC-5.1.1Rev5 October 2002 323 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: nass Table: Origin (Originref, Origin_temp_ga) Description: Number of associated arrivals. This column gives the number of arrivals associated with the origin. Format: number(4) External: i4 NA Value: –1 Range: nass > 0

Name: navcep Table: Timefreq Description: Average maximum value in the two-dimensional cepstrum of the north component traces. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: navcep ≥ 0

Name: nave Table: Fsave Description: Number of spectra averaged to produce the averaged spectrum. Format: number(4) External: i4 NA Value: NOT ALLOWED Range: nave ≥ 1

Name: navcor Table: Timefreq Description: Average autocorrelation along the time axis across all frequencies excluding randomized points of the north component traces. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: navcor ≥ 0

Database Schema

324 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: navpct Table: Timefreq Description: Average ratio of bad points to total of the north component traces. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: 0 ≤ navpct ≤ 1

Name: ncalib Table: Beamaux, Instrument Description: Nominal calibration factor. This conversion factor maps digital data to earth displacement. The factor holds true at the oscillation period specified by ncalper. A positive value means ground motion increasing in component direction (up, north, east) is indicated by increasing counts. A negative value means the opposite. Actual calibration for a particular recording is determined using the Wfdisc (Wfproto) and Sensor tables (see calratio). Format: float(24) External: f16.6 NA Value: NOT ALLOWED Units: nanometers/digital count Range: ncalib ≠ 0

Name: ncalper Table: Beamaux, Instrument Description: Calibration period. This column is the period for which ncalib is valid. Format: float(24) External: f16.6 NA Value: NOT ALLOWED Units: seconds Range: ncalper > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 325 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: nconstseg Table: Qcstats Description: Number of constant valued segments in the detection processing interval. Format: number(8) External: i8 NA Value: –1 Range: nconstseg ≥ 0

Name: ndc Table: Fwfile, Fwgap, Fwsite Description: Destination to which data are forwarded by the Continuous Data Subsystem. Format: varchar2(6) External: a6 NA Value: - (hyphen) Range: any upper-case string up to six characters

Name: ndef Table: Ev_summary (Ex_summary, An_summary), Origin (Originref, Origin_temp_ga) Description: Number of time-defining phases. Format: number(4) External: i4 number(8) for ev_summary NA Value: –1 Range: 0 < ndef ≤ nass

Name: ndef1 Table: Bull_comp Description: Number of time-defining phases for orid1. Format: number(8) External: i8 NA Value: –1 Range: ndef1 ≥ 0

Database Schema

326 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: ndef1arr2 Table: Bull_comp Description: Number of defining arrivals for orid1 that are arrivals (defining or nondefining) for orid2. Format: number(8) External: i8 NA Value: –1 Range: ndef1arr2 ≥ 0

Name: ndef2 Table: Bull_comp Description: Number of time-defining phases for orid2. Format: number(8) External: i8 NA Value: –1 Range: ndef2 ≥ 0

Name: ndef2arr1 Table: Bull_comp Description: Number of defining arrivals for orid2 that are arrivals (defining or nondefining) for orid1. Format: number(8) External: i8 NA Value: –1 Range: ndef2arr1 ≥ 0

Name: ndp Table: Origin (Originref, Origin_temp_ga) Description: Number of depth phases. This column gives the number of depth phases used in calculating depth/depdp (see depdp). Format: number(4) External: i4 NA Value: –1 Range: ndp ≥ 0

Database Schema

IDC-5.1.1Rev5 October 2002 327 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: ndp_snr_pp Table: Evsc_prod Description: Number of pP depth phases meeting the snr criterion defined by min_dp_snr_pp of table Producttypeevsc. Format: number(8) External: i8 NA Value: –1 Range: ndp_snr_pp > –1

Name: ndp_snr_sp Table: Evsc_prod Description: Number of sP depth phases meeting the snr criterion defined by min_dp_snr_sp of table Producttypeevsc. Format: number(8) External: i8 NA Value: –1 Range: ndp_snr_sp > –1

Name: nearaz Table: Ev_summary (Ex_summary, An_summary) Description: Azimuth from nearest station to the event. Format: float(24) External: f7.2 NA Value: –1.0 Units: degrees Range: 0 ≤ nearaz < 360.0

Database Schema

328 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: neardist Table: Ev_summary (Ex_summary, An_summary) Description: Distance from the event to the closest station. Format: float(24) External: f8.3 NA Value: –1.0 Units: kilometers Range: neardist > 0.0

Name: nearsta Table: Ev_summary (Ex_summary, An_summary) Description: Code for the nearest station to the event. Format: varchar2(6) External: a6 NA Value: - (hyphen) Range: any valid station code

Name: net Table: Affiliation (Stanet), Hydro_arr_group, Netmag, Network, Participation, Sitepoll, Weights Description: Unique network identifier. This character string is the name of a seismic network. One example is WWSSN. Format: varchar2(8) External: a8 varchar2(6) for sitepoll NA Value: NOT ALLOWED - (hyphen) for netmag Range: any string up to eight characters

Database Schema

IDC-5.1.1Rev5 October 2002 329 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: netname Table: Network Description: Network name. String containing the name of a network. Format: varchar2(80) External: a80 NA Value: - (hyphen) Range: any string up to 80 characters

Name: nettype Table: Network Description: Network type. This four-character string specifies the type of network (ar = array, lo = local area, ww = world-wide) for the given value of net. Format: varchar2(4) External: a4 NA Value: - (hyphen) Range: any lower-case string up to four characters

Name: nevyr Table: Seisgrid (Dseisgrid) Description: Average number of events per year with magnitude above magth whose location is within the grid cell defined by icell. Format: float(24) External: f9.2 NA Value: NOT ALLOWED Range: nevyr ≥ 0

Name: nf Table: Fsave, Fsdisc Description: Number of frequency values in the spectrum file. Format: number(8) External: i4 NA Value: NOT ALLOWED Range: nf > 0

Database Schema

330 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: nfft Table: Fsrecipe Description: Number of data points in FFT. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: nfft > 1

Name: nhydarr Table: Hydro_arr_group Description: Number of arrivals in the group. Format: number(4) External: i4 NA Value: –1 Range: nhydarr ≤ number of stations in the group

Name: nlat Table: Seisindex (Dseisindex) Description: Number of latitudes in Seisgrid (Dseisgrid). Format: number(8) External: i8 NA Value: NOT ALLOWED Range: nlat > 0.0

Name: nlon Table: Seisindex (Dseisindex) Description: Number of longitudes in Seisgrid (Dseisgrid). Format: number(8) External: i8 NA Value: NOT ALLOWED Range: nlon > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 331 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: nmatch Table: Bull_comp Description: Number of matching arrivals (defining or nondefining) between orid1 and orid2. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: nmatch ≥ 0

Name: nois Table: Siteaux Description: Nominal background seismic noise level. Format: float(24) External: f10.1 NA Value: –1.0 Units: nanometers Range: nois ≥ 0.0

Name: noise_high_band Table: Evsc_hydro Description: Hydroacoustic noise level in the high-frequency band (32–64 Hz) from table amplitude for a given orid/sta pair. Format: float(24) External: f7.2 NA Value: –1.0 Units: dB re µPa Range: noise_high_band > 0.0

Database Schema

332 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: noissd Table: Fsave, Siteaux Description: Standard deviation of the log noise amplitude. Format: float(24) External: f5.2 NA Value: –999.0 Range: noissd > 0.0

Name: note_missing_data Table: Arch_data_type Description: Missing data flag. If y, there are missing data for the datatype indicated in the arch_data_type table. Format: varchar2(2) External: a2 NA Value: - (hyphen) Range: note_missing_data ∈ {y, n}

Name: nsamp Table: Wfdisc (Wfproto) Description: Number of samples. This quantity is the number of samples in a waveform segment. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: nsamp > 0

Name: nseg Table: Qcstats Description: Number of masked segments in the detection processing interval. Format: number(8) External: i8 NA Value: –1 Range: nseg ≥ 0

Database Schema

IDC-5.1.1Rev5 October 2002 333 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: nsta Table: Ev_summary (Ex_summary, An_summary), Netmag, Origaux Description: Number of stations. In ev_summary this column is the number of stations with an associated arrival. In netmag this column is the number of stations contributing to the network magnitude estimate. In origaux this column is the number of defining stations. Format: number(8) External: i8 NA Value: –1 Range: nsta > 0 1 ≤ nsta ≤ 9999 for origaux

Name: nsta_mb Table: Evsc_prod

Description: Number of stations contributing to the mb estimate used in event screening. Format: number(8) External: i8 NA Value: –1 Range: nsta_mb > –1

Name: nsta_ms Table: Evsc_prod

Description: Number of stations contributing to the Ms estimate used for event screening. Format: number(8) External: i8 NA Value: –1 Range: nsta_ms > –1

Database Schema

334 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: num_cross Table: Hydro_features Description: Number of times that the estimated signal pressure squared crosses noise_onset_thresh between onset_time and termination_time. Format: number(8) External: i8 NA Value: –1 Range: num_cross > 0

Name: numfailedattempt Table: Ftpfailed Description: Number of failed attempts to retrieve message via FTP. Format: number(4) External: i4 NA Value: 0 Range: numfailedattempt > 0

Name: nx Table: Fkdisc Description: Total number of X sample points (either slowness or wavenumber, depending on fktyp) in a f-k spectrum. Format: number(4) External: i4 NA Value: NOT ALLOWED Range: nx > 0

Name: ny Table: Fkdisc Description: Total number of Y sample points (either slowness or wavenumber, depending on fktyp) in a f-k spectrum. Format: number(4) External: i4 NA Value: NOT ALLOWED Range: ny > 0

Database Schema

IDC-5.1.1Rev5 October 2002 335 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: objtype Table: Ga_tag Description: Defines the id as either an arid (a) or an orid (o). Format: varchar2(1) External: a1 NA Value: NOT ALLOWED Range: objtype ∈ {a, o}

Name: obsolete Table: Fileproduct (Fs_stageproduct) Description: Flag to indicate if the data in the fileproduct file are obsolete. 0 indicates that the data are not obsolete, and 1 indicates that the data are obsolete. Format: number(1) External: i1 NA Value: NOT ALLOWED Range: obsolete ∈ {0, 1}

Name: offdate Table: Arch_data_type, Chan_groups, Exception_chanmap, Regcoef, Site, Sitechan, Std_chanmap, Subs, Weights Description: Turn off date. This column is the date after which the archive specifications, regional coefficient, station, sensor, or subscription indicated was no longer applicable, turned off, dismantled, or moved (see ondate). Format: number(8) External: a17 date for subs. NA Value: –1 Jan 1, 4700 for subs Range: Julian date of the form yyyyddd any valid oracle date for subs

Database Schema

336 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: ondate Table: Arch_data_type, Chan_groups, Exception_chanmap, Regcoef, Site, Sitechan, Std_chanmap, Subs, Weights Description: Turn on date. This column is the date on which the archive specifications, regional coefficient, station, sensor, or subscription indicated became applicable or began operating. Offdate and ondate are not intended to accommodate temporary downtimes, but rather to indicate the time period for which the columns of the station (lat, lon, elev) are valid for the given station code. Stations are often moved, but with the station code remaining unchanged. Format: number(8) External: a17 date for subs NA Value: NOT ALLOWED Range: Julian date of the form yyyyddd any valid oracle date for subs

Name: onset_time Table: Hydro_features Description: Estimated onset time of signal. Format: float(53) External: f17.5 NA Value: NOT ALLOWED Units: seconds Range: any valid epoch time

Name: orderby Table: Seisindex (Dseisindex) Description: Grid order. The seismic grid can either be ordered by latitude or by longitude. Format: varchar2(6) External: a6 NA Value: NOT ALLOWED Range: orderby ∈ {lat, lon}

Database Schema

IDC-5.1.1Rev5 October 2002 337 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: orid Table: Assoc (Assoc_temp_ga), Ceppks, Complexity, Ev_summary (Ex_summary, An_summary), Event_control (In_event_control), Evsc_hydro, Evsc_prod, Evsc_regional, Explo, Netmag, Origaux, Origerr (Origerr_temp_ga), Origin (Originref, Origin_temp_ga), Parrival, Request, Splp, Stamag, Timefreq Description: Origin identifier that relates a record in these tables to a record in the origin table. In the disorigin table, orid refers to the analyst origin corresponding to a dissolved expert system event. Format: number(8) External: i8 NA Value: NOT ALLOWED –1 for disorigin, origaux Range: orid > 0

Name: orid1 Table: Bull_comp Description: Origin identifier from the bulletin1 database Origin (Originref, Origin_temp_ga) table. Format: number(8) External: i8 NA Value: –1 Range: orid1 > 0

Name: orid2 Table: Bull_comp Description: Origin identifier from the bulletin2 database Origin (Originref, Origin_temp_ga) table. Format: number(8) External: i8 NA Value: –1 Range: orid2 > 0

Database Schema

338 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: otfixf Table: Origaux Description: Flag designating that an origin time is fixed. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: otfixf ∈ {f}

Name: otgid Table: Outage Description: Outage identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: otgid > 0

Name: outauth Table: Wfconv Description: Flag showing if output data are authenticated. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: outauth ∈ {y, n}

Name: outcomp Table: Wfconv Description: Output data compression type. The only type currently supported is Canadian compression (CA). Format: varchar2(2) External: a2 NA Value: 0 Range: outcomp ∈ {CA}

Database Schema

IDC-5.1.1Rev5 October 2002 339 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: outsamp Table: Wfconv Description: Number of output samples per packet. Format: number(8) External: i8 NA Value: 0 Range: outsamp > 0

Name: outtype Table: Wfconv Description: Output fixed width datatype. Format: varchar2(2) External: a2 NA Value: - (hyphen) Range: same as datatype

Name: overlap Table: Fsrecipe Description: Percent overlap of windows. Format: number(8) External: i3 NA Value: NOT ALLOWED Range: 0 < overlap < 100

Name: overlayid Table: Mapover, Overlaydisc Description: Overlay identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: overlayid > 0

Database Schema

340 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: overlayname Table: Overlaydisc Description: Name of the map overlay. Format: varchar2(64) External: a64 NA Value: - (hyphen) Range: any free format character string up to 64 characters

Name: paleodepth Table: Explo Description: Depth to the Paleozoic layer, measured from the surface. Format: float(24) External: f7.4 NA Value: –1 Units: kilometers Range: paldep ≥ 0.0

Name: parid Table: Amplitude, Parrival Description: Predicted arrival identifier. Every event-based parrival measure is assigned a unique positive integer that identifies it in the database. If an associated amplitude record exists, then parid links it to parrival. Format: number(8) External: i8 NA Value: NOT ALLOWED –1 for amplitude Range: parid > 0

Database Schema

IDC-5.1.1Rev5 October 2002 341 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: partition Table: Dlfile Description: Disk partition name. Format: varchar2(64) External: a64 NA Value: NOT ALLOWED Range: any string up to 64 characters that is a valid disk partition

Name: password Table: Ftplogin Description: Password for remote FTP site for pushing data messages from PIDC. Format: varchar2(16) External: a16 NA Value: NOT ALLOWED Range: any string up to 16 characters

Name: pctoffsh Table: Evsc_prod Description: Percentage of location error ellipse that is determined to be offshore. Format: float(24) External: f7.2 NA Value: –999.0 Range: 0.0 ≤ pctoffsh < 100.0

Name: peak_level Table: Hydro_features Description: Pressure of largest absolute signal value. Format: float(24) External: f9.4 NA Value: –1.0 Units: dB re µPa Range: peak_level ≥ 0.0

Database Schema

342 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: peak_time Table: Hydro_features Description: Epoch time of largest absolute signal value. Format: float(53) External: f17.5 NA Value: NOT ALLOWED Units: seconds Range: any valid epoch time

Name: per Table: Amplitude, Arrival Description: Measured period at the time of the amplitude measurement. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds Range: per > 0.0

Name: phase Table: Allow_resid, Apma, Assoc (Assoc_temp_ga), Complexity, Parrival, Stamag, Weights Description: Phase type. The identity of a phase that has been associated to an arrival. Stan- dard labels for phases are used (for example, P, PKP, PcP, pP, and so on). Both upper- and lower-case letters are available and should be used when appropriate; for example, pP or PcP. Format: varchar2(8), External: a8 varchar2(6) for complexity NA Value: - (hyphen) if this column does not apply to seismic phases Range: any string up to eight characters that conforms to scientific practice

Database Schema

IDC-5.1.1Rev5 October 2002 343 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: pkamp Table: Ceppks Description: Amplitude of consistent cepstral peak. This column value is set to zero if there are no consistent peaks. Format: float(24) External: f7.5 NA Value: 0.0 Units: nanometer-seconds Range: pkamp > 0.0

Name: pkqf Table: Ceppks Description: Frequency of consistent cepstral peak. This column value is set to zero if no consistent peaks exist. Format: float(24) External: f8.4 NA Value: 0.0 Units: seconds Range: pkqf > 0.0

Name: planlr Table: Apma

Description: Planarity of an S-type polarization column defined as 1 – l3/l2, where l2 and l3 are eigenvalues from the decomposition of the covariance matrix. Planarity is measured at the time of maximum 3-component amplitude. Format: float(24) External: f7.2 NA Value: –1.0 Range: 0.0 ≤ planlr ≤ 1.0

Database Schema

344 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: plans Table: Apma

Description: Planarity of an S-type polarization column defined as 1 – l3/l2, where l2 and l3 are eigenvalues from the decomposition of the covariance matrix. Planarity is measured at the time of maximum 3-component amplitude. The only difference between plans and planlr is in the definition of the overlapping time windows. Format: float(24) External: f7.2 NA Value: –1.0 Range: 0.0 ≤ plans ≤ 1.0

Name: plid Table: Problemlog Description: Problem log identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: plid > 0

Name: pn_snr Table: Evsc_regional Description: Signal-to-noise ratio of the Pn measurement. Format: float(24) External: f7.2 NA Value: –999.0 Range: pn_snr > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 345 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: pnlg Table: Evsc_regional Description: Logarithm (base 10) of the distance corrected Pn/Lg ratio. Format: float(24) External: f7.2 NA Value: –999.0 Range: pnlg > –999.0

Name: pnlg_qual Table: Evsc_regional Description: Data quality indicator for the Pn/Lg measurement. A string of zeros indicates good data quality. See quality flag note for pnsn_qual. Format: varchar2(10) External: a10 NA Value: - (hyphen) Range: any valid ORACLE string

Name: pnsmax Table: Evsc_regional Description: Maximum of the Pn/Sn and Pn/Lg ratios. Format: float(24) External: f7.2 NA Value: –999.0 Range: pnsmax > –999.0

Name: pnsmax_corr Table: Evsc_regional Description: Correction term of the maximum of the Pn/Sn and Pn/Lg ratios. Format: float(24) External: f7.2 NA Value: –999.0 Range: pnsmax_corr > –999.0

Database Schema

346 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: pnsmax_err Table: Evsc_regional Description: Standard error of the maximum of the Pn/Sn and Pn/Lg ratios. Format: float(24) External: f7.2 NA Value: –999.0 Range: pnsmax_err > –999.0

Name: pnsn Table: Evsc_regional Description: Logarithm (base 10) of the distance-corrected Pn/Sn amplitude ratio. Format: float(24) External: f7.2 NA Value: –999.0 Range: pnsn > –999.0

Name: pnsn_qual Table: Evsc_regional Description: Data quality indicator for the Pn/Sn amplitude ratio measurement. A string of zeros indicates good data quality. Each position in the quality string indicates the state of data quality test. A ‘0’ character indicates the data passed the test, a ‘1’ indicates the data failed the test. Reading from left-to-right, the test indi- cators are ordered as follows: 1. Missing data - ‘1’ indicates that Pn, Sn, Lg signal or noise values are not available for the calculation. 2. Signal-to-noise - ‘1’ indicates that the snr for a given amplitude ratio does not satisfy the input criteria. 3. No distance correction - ‘1’ indicates that there is no distance correction data available to apply to this amplitude ratio (see Attencoef). 4. Exceeds valid range of distance correction - ‘1’ indicates the event is outside the valid range of applicability for the distance correction given in Atten- coef. 5. No correction grid file - ‘1’ indicates there is no correction grid file provided for the station under consideration. 6. Exceeds valid range of correction grid file - ‘1’ indicates the event is outside the valid range of the correction grid file provided for the station.

Database Schema

IDC-5.1.1Rev5 October 2002 347 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

7. Spare field (not currently used) - set to ‘0’. 8. Anomalous data value - ‘1’ indicates an anomalous regional phase amplitude measurement, invalidating the P/S measurement. Format: varchar2(10) External: a10 NA Value: - (hyphen) Range: any valid ORACLE string

Name: pocid Table: Datauser, Subsuser Description: Point of contact identifier. Format: number(8) External: i8 NA Value: –1 Range: pocid > 0

Name: pointspike Table: Qcstats Description: Amount of data in the detection processing interval masked due to point- spikes. Format: float(53) External: f17.5 NA Value: –999.0 Units: seconds Range: pointspike ≥ 0.0

Name: port Table: Fwsite Description: Port on which the connection manager is listening. Format: number(6) External: i8 NA Value: –1 Range: 1 < port < 16383

Database Schema

348 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: prefdlid Table: Alphasite Description: dlid for preferred DLMan for a given station. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: prefdlid > 0

Name: prefer_loc Table: Event_control (In_event_control) Description: Preferred location identifier. This column indicates which of three possible location solutions is the chosen location. The hypocenter can be either held to a surface location (S), determined with no constraints at all (free depth, F), or restrained based on the settings of constrain_ot, constrain_latlon, and constrain_depth, (R). The constrained location (R) can be fixed in origin time/ latitude and longitude/depth. Prefer_loc takes precedence to the actual constraint settings (constrain_ot, constrain_latlon, and constrain_depth) when prefer_loc indicates a surface (S) or free depth (F) location. Default is “S.” Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: prefer_loc ∈ {F, S, R}

Name: prefor Table: Event Description: Preferred origin. This column holds the origin identifier (orid) that points to the preferred origin for a seismic event. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: prefor > 0

Database Schema

IDC-5.1.1Rev5 October 2002 349 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: prefport Table: Alphasite Description: Preferred network port for a given station. Format: number(6) External: i8 NA Value: 0 Range: 1 ≤ prefport ≤ 16383

Name: prid Table: Problem, Problemlog Description: Problem identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: prid > 0

Name: primarykey Table: Arch_data_type Description: Not used. Format: varchar2(24) External: a24 NA Value: - (hyphen) Range: any string up to 24 characters

Name: primp Table: Ev_summary (Ex_summary, An_summary) Description: Number of primary time-defining phases. A primary phase is defined as the first phase for a given station belonging to the set (P, Pn, Pg, PKP, PKPdf). Format: number(8) External: i8 NA Value: –1 Range: primp ≥ 0

Database Schema

350 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: priority Table: Datauser, Fwsite, Subsuser Description: Priority assigned to process. Format: number(2) External: i2 NA Value: –1 NOT ALLOWED for datauser Range: priority > 0

Name: prob_weight_time Table: Hydro_features Description: Probability weighted time. The weight for a sample is the probability that the sample’s amplitude is the maximum amplitude associated with the arrival within the frequency band defined by low_cut, high_cut, ford, and ftype. Format: float(53) External: f17.5 NA Value: –999.0 Units: seconds Range: any valid epoch time

Name: procclass Table: Mig_date, Problem, Problemmail, Timestamp Description: Process class used to group processes. Format: varchar2(16) External: a16 varchar2(17) for problem, problemmail NA Value: NOT ALLOWED Range: any string (upper case for mig_date) up to 16 characters

Database Schema

IDC-5.1.1Rev5 October 2002 351 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: procname Table: Mig_date, Problem, Timestamp Description: Process name that identifies a process within a process class. Format: varchar2(16) External: a16 varchar2(17) for problem NA Value: NOT ALLOWED Range: any string (upper case for mig_date) up to character limit

Name: prodfmt Table: Productcriteria Description: Product format. Format: varchar2(6) External: a6 NA Value: - (hyphen) Range: prodfmt ∈ {GSE2.0, IMS1.0}

Name: prodid Table: Evsc_prod, Prodtrack, Productcriteria, Producttypeevsc, Producttypeorigin, Producttypesta, Subs Description: Product identifier. Format: number(8) External: i8 NA Value: –1 Range: prodid > 0

Name: prodname Table: Productcriteria Description: Name of the product. Format: varchar2(24) External: a24 NA Value: - (hyphen) Range: any valid string up to 24 characters

Database Schema

352 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: prodsubtype Table: Productcriteria Description: Subtype of the product. Format: varchar2(12) External: a12 NA Value: - (hyphen) Range: prodsubtype ∈ {sel1, sel2, sel3, reb, and so on}

Name: prodtype Table: Fpdescription, Productcriteria Description: Product type. Format: varchar2(12) External: a12 varchar2(32) for productcriteria NA Value: - (hyphen) Range: prodtype ∈ {origin, event, bulletin, arrival, detection, waveform}

Name: projection Table: Mapdisc Description: Projection of the Map; a positive integer enumerator for uniquely classifying the stereographic projection of the Map. Azimuthal equidistant = 2; Mercator = 3. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: projection ∈ {2, 3}

Database Schema

IDC-5.1.1Rev5 October 2002 353 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: ptime Table: Apma Description: Epoch time at which P-type polarization columns are estimated. This column value is the center of the time window with maximum rectilinearity. Format: float(53) External: f17.5 NA Value: –9999999999.999 Units: seconds Range: any valid epoch time

Name: ptmcor Table: Siteaux Description: P-wave arrival time correction. Format: float(24) External: f6.3 NA Value: –999.0 Units: seconds Range: ptmcor > –999.0

Name: ptyp Table: Ceppks Description: Consistent cepstral peak type. This column is FC-PHS if consistent Fourier cepstral peaks are found across two or more phases for one array and no peak is in the noise cepstrum at this quefrency. Otherwise, it is “-” if no consistent cepstral peaks are found. Format: varchar2(6) External: a6 NA Value: - (hyphen) Range: ptyp ∈ {FC-PHS}

Database Schema

354 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: qcstatsid Table: Qcstats Description: Data quality statistics identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: qcstatsid > 0.0

Name: qual Table: Arrival Description: Onset quality. This single-character flag is used to denote the sharpness of the onset of a seismic phase. This relates to the timing accuracy as follows:

i (impulsive) – accurate to ±0.2 seconds e (emergent) – accuracy between ±(0.2 to 1.0 seconds) w (weak) – timing uncertain to > 1 second Format: varchar (1) External: a1 NA Value: - (hyphen) Range: qual ∈ {i, e, w}

Name: quer_seq_no Table: Mig_rules Description: Order of this part of the query for data migration. Format: number External: i4 NA Value: NOT ALLOWED Range: quer_seq_no ≥ 1

Database Schema

IDC-5.1.1Rev5 October 2002 355 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: query_type Table: Mig_rules Description: Type of query for data migration. Format: varchar2(20) External: a20 NA Value: NOT ALLOWED Range: query_type ∈ {COMMIT, CREATE_TABLE, DELETE, DROP_TABLE, SELECT_INSERT}

Name: ratio Table: Splp Description: Ratio of short-period to long-period energy. Format: float(24) External: f10.8 NA Value: NOT ALLOWED Range: ratio > 0

Name: ratiotype Table: Attencoef Description: Amplitude ratio type. This identifies the type of P/S amplitude ratio (for example, Pn/Lg or Pn/Sn) for which the attenuation coefficients apply. Format: varchar2(6) External: a6 NA Value: - (hyphen) Range: any valid string up to 6 characters

Name: rcoefid Table: Regcoef Description: Linear coefficient set identifier. Format: varchar2(20) External: a20 NA Value: - (hyphen) Range: any valid string up to 20 characters

Database Schema

356 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: rcoeftype Table: Regcoef Description: Type of linear weighting coefficient used in regional P/S screening criterion. Format: varchar2(10) External: a10 NA Value: - (hyphen) Range: any valid string up to 10 characters

Name: rcoefvalue Table: Regcoef Description: Value of linear weighting coefficient used in regional P/S screening criterion. Identified by rcoeftype. Format: float(24) External: f7.2 NA Value: –999.0 Range: any valid floating point value

Name: rdepthp Table: Ex_an Description: Number of depth phases renamed by the analyst (see ddepthp for definition of depth phase). Format: number(8) External: i8 NA Value: –999 Range: rdepthp > 0

Name: reaptime Table: Dlfile Description: Time at which the contents of the disk loop file may be discarded and the file re-used. Format: float(53) External: f17.5 NA Value: 0.0 Range: any valid epoch time > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 357 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: reason Table: Discard Description: Reason an automated system event was discarded by an analyst. Format: varchar2(30) External: a30 NA Value: NOT ALLOWED Range: any string up to 30 characters

Name: rect Table: Apma, Arrival Description: Signal rectilinearity defined as

1 – (l3 + l2)/2l1

where l1, l2, and l3 are the three eigenvalues from the decomposition of the covariance matrix. This column value is the maximum rectilinearity for all overlapping time windows. Format: float(24) External: f7.3 NA Value: –1.0 Range: 0.0 ≤ rect ≤ 1.0

Name: rectype Table: Complexity, Splp, Thirdmom, Timefreq Description: Recipe type. This term identifies the algorithm used to calculate the parameter. Format: varchar2(8) External: a8 NA Value: - (hyphen) NOT ALLOWED for timefreq, thirdmom Range: any string up to eight characters

Database Schema

358 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: refaz Table: Ev_summary (Ex_summary, An_summary) Description: Azimuth to nearest reference point (reference locations are stored in the Ref_loc table). Format: float(24) External: f7.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ refaz < 360.0

Name: refdist Table: Ev_summary (Ex_summary, An_summary) Description: Distance to nearest reference point (reference locations are stored in the Ref_loc table). Format: float(24) External: f8.3 NA Value: –1.0 Units: kilometers Range: refdist ≥ 0.0

Name: refid Table: Ev_summary (Ex_summary, An_summary), Ref_loc Description: Reference location identifier. Format: number(8) External: i8 NA Value: –1 Range: refid > 0

Database Schema

IDC-5.1.1Rev5 October 2002 359 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: reflat Table: Mapdisc Description: Latitude reference; latitude of the center of the Map application’s projection (used for azimuthal equidistant projections only). Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: –90.0 ≤ reflat ≤ 90.0

Name: reflon Table: Mapdisc Description: Longitude reference. Longitude of the center of the Map application’s projection (used for azimuthal equidistant projections only). Format: float(24) External: f9.4 NA Value: –999.0 Units: degrees Range: –180.0 ≤ reflon ≤ 180.0

Name: refname Table: Ref_loc Description: Reference location name. Format: varchar2(16) External: a16 NA Value: NOT ALLOWED Range: any upper case string up to 16 characters

Database Schema

360 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: refoffsetlat Table: Mapdisc Description: Latitude offset reference. This column value is the reference (in pixels) from the lower left corner of the map to the center of the Map application’s projection. In the case where the reference point is at the center of the map, the off- sets are equal to half the map width and height. For azimuthal equidistant projections only. Format: float(24) External: f9.4 NA Value: –1.0 Units: pixels Range: refoffsetlat > 0

Name: refoffsetlon Table: Mapdisc Description: Longitude offset reference. This column value is the reference (in pixels) from the lower left corner of the map to the center of the Map application’s projection. For azimuthal equidistant projections only. Format: float(24) External: f9.4 NA Value: –1.0 Units: pixels Range: refoffsetlon > 0

Name: refsta Table: Site Description: Reference station. This string specifies the reference station with respect to which array members are located (see deast, dnorth). Format: varchar2(6) External: a6 NA Value: - (hyphen) Range: any sta from tables

Database Schema

IDC-5.1.1Rev5 October 2002 361 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: reg_conf Table: Producttypeevsc Description: Confidence level of the regional seismic P/S screening criterion. Format: float(24) External: f7.2 NA Value: –999.0 Range: 0.0 < reg_conf < 1.0

Name: regname Table: Producttypeevsc Description: Region name for subscriptions. Format: varchar2(24) External: a24 NA Value: - (hyphen) Range: any valid string up to 24 characters

Name: rely Table: Siteaux Description: Station reliability. This column is an estimate of the percentage of time that the station is up. Format: float(24) External: f5.2 NA Value: –1.0 Range: 0.0 ≤ rely ≤ 1.0

Database Schema

362 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: remark Table: Remark Description: Descriptive text. This single line of text is an arbitrary comment about a record in the database. The comment is linked to its parent table only by forward reference from commid in the record of the table of interest (see commid, lineno). Format: varchar2(80) External: a80 NA Value: - (hyphen) Range: any string up to 80 characters

Name: reqid Table: Request Description: Request identifier. Unique key to allow tracking of requests by the Message Subsystem. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: reqid > 0

Name: requestor Table: Request Description: Original requestor of this data. The requestor is the person or program that requests this waveform data. Format: varchar2(15) External: i15 NA Value: - (hyphen) Range: any string up to 15 characters

Database Schema

IDC-5.1.1Rev5 October 2002 363 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: response Table: Fsrecipe Description: Flag specifying instrument response function. Format: varchar2(1) External: a1 NA Value: NOT ALLOWED Range: response ∈ {y, n}

Name: retime Table: Ex_an Description: Number of phases re-timed by an analyst. Format: number(8) External: i8 NA Value: –1 Range: retime ≥ 0

Name: revfunction Table: Revaudit Description: Name of the revision function used. Format: varchar2(32) External: a32 NA Value: NOT ALLOWED Range: any function name in rebrevise

Name: revid Table: Revaudit Description: Revision identifier. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: revid > 0

Database Schema

364 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: revision Table: Fileproduct (Fs_stageproduct) Description: Revision number of a file product. Format: number(4) External: i4 NA Value: –1 Range: revision > 0

Name: revstate Table: Revaudit Description: State of the revision. Format: varchar2(16) External: a16 NA Value: NOT ALLOWED Range: revstate ∈ {DONE|FAILED|ABORTED}

Name: revtagid1 Table: Revaudit Description: Value of the foreign key named in revtagname1. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: revtagid1 > 0

Name: revtagid2 Table: Revaudit Description: Value of the foreign key named in revtagname2. Format: number(8) External: i8 NA Value: –1 Range: revtagid2 > 0

Database Schema

IDC-5.1.1Rev5 October 2002 365 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: revtagname1 Table: Revaudit Description: Name of the foreign key whose value is in revtagid1. Format: varchar2(8) External: a8 NA Value: NOT ALLOWED Range: revtagname1 ∈ {valid identifier}

Name: revtagname2 Table: Revaudit Description: Name of the foreign key whose value is in revtagid2. Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: revtagname2 ∈ {valid identifier}

Name: rid Table: Amp3c Description: Recipe identifier. Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: any string up to eight characters long

Database Schema

366 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: rotation Table: Mapdisc Description: Map rotation. This is the rotation of the projection from 0°, or due north. Rotation specifies the azimuth of the y-raster in degrees clockwise from north (for azimuthal equidistant projections only). Format: float(24) External: f9.4 NA Value: –1.0 Units: degrees Range: 0.0 ≤ rotation < 360.0

Name: rprimp Table: Ex_an Description: Number of primary phases renamed by the analyst (see dprimp for definition of primary phase). Format: number(8) External: i8 NA Value: –1 Range: rprimp ≥ 0

Name: rscore Table: Evsc_prod Description: Score for the regional seismic P/S event-screening criterion. Format: float(24) External: f7.2 NA Value: –999.0 Range: rscore > –999.0

Database Schema

IDC-5.1.1Rev5 October 2002 367 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: rsecondp Table: Ex_an Description: Number of secondary phases renamed by the analyst (see dsecondp for definition of secondary phase). Format: number(8) External: i8 NA Value: –1 Range: rsecondp ≥ 0

Name: rsptype Table: Instrument Description: Instrument response type. The column value denotes the style in which detailed calibration data are stored. The neighboring column dfile tells where the calibration data are saved. Rsptype = paz indicates the data are the poles and zeroes of the Laplace transform. Rsptype = fap indicates the data are amplitude/phase values at a range of frequencies. Rsptype = fir indicates that the response type is a finite impulse response table. Rsptype = pazfir indicates a combination of poles, zeros, and finite impulse response. Other codes may be defined. Format: varchar2(6) External: a6 NA Value: NOT ALLOWED Range: any lower-case string up to six characters

Name: rsta Table: Ev_summary (Ex_summary, An_summary) Description: Number of nonarray regional arrival times. “Regional” is defined as a station- event distance not less than 250 km and up to 2000 km. Format: number(8) External: i8 NA Value: –1 Range: rsta ≥ 0

Database Schema

368 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: running Table: Dlman Description: Flag indicating whether or not DLMan is running. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: running ∈ {y, n}

Name: samprate Table: Instrument, Wfdisc (Wfproto) Description: Sampling rate. This column is the sample rate in samples/second. In the instrument table, the column value is specifically the nominal sample rate, not accounting for clock drift. In wfdisc, the value may vary slightly from the nominal to reflect clock drift. Format: float(24) External: f11.7 NA Value: NOT ALLOWED Units: 1/seconds Range: samprate > 0.0

Name: scale Table: Mapdisc Description: Map scale. Format: float(24) External: f9.4 NA Value: –1.0 Units: radians per pixel for mercator projections; kilometers per pixel for azimuthal equidistant projections Range: scale > 0

Database Schema

IDC-5.1.1Rev5 October 2002 369 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: scan Table: Scan_date Description: Status of analyst scanning for missed events. Format: varchar2(1) External: a1 NA Value: NOT ALLOWED Range: scan ∈ {y, n}

Name: score Table: Evsc_prod Description: Composite event-screening score. This score numerically indicates the degree to which a particular event meets or does not meet the combined screening criteria. Format: float(24) External: f7.2 NA Value: –999.0 Range: score > –999.0

Name: sdepth Table: Origerr (Origerr_temp_ga) Description: Depth error. This is the maximum error of a depth estimate for a level of confidence given by conf (see smajax, sminax, and sxx, syy, szz, stt, sxy, sxz, syz, stx, sty, stz). Format: float(24) External: f9.4 NA Value: –1.0 Units: kilometers Range: sdepth > 0.0

Database Schema

370 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: sdobs Table: Origerr (Origerr_temp_ga) Description: Standard error of one observation. This column is derived from the discrepan- cies in the arrival times of the phases used to locate an event. This column is defined as the square root of the sum of the squares of the time residuals divided by the number of degrees of freedom. The latter is the number of defining observations (ndef in Origin (Originref, Origin_temp_ga)) minus the dimension of the system solved (4 if depth is allowed to be a free variable, 3 if depth is constrained). Format: float(24) External: f9.4 NA Value: –1.0 Range: sdobs > 0.0

Name: seaz Table: Assoc (Assoc_temp_ga), Detection Description: Station-to-event azimuth calculated from the station and event locations and measured clockwise from north. Format: float(24) External: f7.2 NA Value: –999.0 Units: degrees Range: 0.0 ≤ seaz ≤ 360.0

Database Schema

IDC-5.1.1Rev5 October 2002 371 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: seazlr Table: Apma

Description: Azimuth of the eigenvector (e3) associated with the smallest eigenvalue (λ3). This column is corrected by 180° to give an estimate of the station-to-event azimuth (with an 180° ambiguity). This column is an S-type column calculated at the time of the maximum 3-component amplitude. The only difference between seazs and seazlr is in the definition of the overlapping time windows. Format: float(24) External: f7.2 NA Value: –999.0 Units: degrees Range: 0.0 ≤ seazlr ≤ 360.0

Name: seazp Table: Apma

Description: Azimuth of the eigenvector (e1) associated with the largest eigenvalue (λ1). The column value is corrected by 180° to give an estimate of the station-to- event azimuth. This P-type value is calculated at the time of maximum rectilinearity. Format: float(24) External: f7.2 NA Value: –999.0 Units: degrees Range: 0.0 ≤ seazp ≤ 360.0

Database Schema

372 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: seazs Table: Apma

Name: secondkey Table: Arch_data_type Description: Not used. Format: varchar2(24) External: a24 NA Value: - (hyphen) Range: any string up to 24 characters

Name: secondp Table: Ev_summary (Ex_summary, An_summary) Description: Number of time-defining secondary phases. A secondary phase is any phase not in the set (P, Pn, Ps, PkP, PKPdf). Format: number(8) External: i8 NA Value: –1 Range: secondp ≥ 0

Database Schema

IDC-5.1.1Rev5 October 2002 373 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: segtype Table: Wfdisc (Wfproto) Description: Segment type. This column indicates if a waveform is o (original), v (virtual), s (segmented), or d (duplicate). Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: segtype ∈ {o, v, s, d}

Name: seq_contents Table: Mig_rules Description: Contents of a query for data migration. Format: varchar2(200) External: a200 NA Value: NOT ALLOWED Range: any string up to 200 characters that is a valid SQL query

Name: seq_type Table: Mig_rules Description: Type of sequence to be added to the query. Format: varchar2(15) External: a15 NA Value: NOT ALLOWED Range: seq_type ∈ {END_LDDATE, START_LDDATE, TEXT}

Database Schema

374 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: servicetime Table: Datauser Description: Last time a request from the user with the userid in the datauser table was ser- viced. Format: float(53) External: f17.5 NA Value: –999999999.999 Units: seconds Range: servicetime ≥ 0

Name: sigma_time Table: Hydro_features Description: Standard deviation of the probability weighted time. Format: float(53) External: f17.5 NA Value: –999.0 Range: sigma_time ≥ 0

Name: sigtype Table: Msgdisc Description: Digital signature type. Format: varchar2(64) External: a64 NA Value: - (hyphen) Range: ASCII character string

Name: skewness Table: Hydro_features Description: Skew of the estimated signal energy between onset_time and termination_time. Format: float(24) External: f9.4 NA Value: –9999999999.999 Range: –10000000.0 < skewness < 10000000.0

Database Schema

IDC-5.1.1Rev5 October 2002 375 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: slodef Table: Assoc (Assoc_temp_ga) Description: Slowness defining code. This one-character flag indicates whether or not the slowness of a phase was used to constrain the event location. This column is defining (slodef = d) or nondefining (slodef = n) for this arrival. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: slodef ∈ {d, n}

Name: slores Table: Allow_resid, Assoc (Assoc_temp_ga) Description: Slowness residual. This column gives the difference between an observed slowness and a theoretical prediction. The prediction is calculated for the related phase and event origin described in the record. Format: float(24) External: f7.2 NA Value: –999.0 Units: seconds/degree Range: slores > –999.0

Name: slow Table: Arrival, Detection, Hydro_arr_group, Parrival Description: Observed slowness of a detected arrival. Units are seconds/kilometer in detection, seconds/degree in arrival and parrival. Format: float(24) External: f7.2 NA Value: –1.0 Range: slow ≥ 0.0

Database Schema

376 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: smaj_sc Table: Evsc_prod Description: Semi-major axis of error ellipse, used for onshore/offshore determination, for a confidence level given by loc_conf of table Producttypeevsc. Format: float(24) External: f7.2 NA Value: –999.0 Units: kilometers Range: smaj_sc > 0.0

Name: smajax Table: Origerr (Origerr_temp_ga) Description: Semi-major axis of error ellipse for a given confidence. The column value is the length of the semi-major axis of the location error ellipse. The value is found by projecting the covariance matrix onto the horizontal plane. The level of confidence is specified by conf (see sdepth, sminax, and sxx, syy, szz, stt, sxy, sxz, syz, stx, sty, stz). Format: float(24) External: f9.4 NA Value: –1.0 Units: kilometers Range: smajax > 0.0

Name: smin_sc Table: Evsc_prod Description: Semi-minor axis of error ellipse, used for onshore/offshore determination, for a confidence level given by loc_conf of table Producttypeevsc. Format: float(24) External: f7.2 NA Value: –999.0 Units: kilometers Range: smin_sc > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 377 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: sminax Table: Origerr (Origerr_temp_ga) Description: Semi-minor axis of error ellipse. The column value is the length of the semi- minor axis of the location error ellipse. The value is found by projecting the covariance matrix onto the horizontal plane. The level of confidence is specified by conf (see sdepth, smajax, and sxx, syy, szz, stt, sxy, sxz, syz, stx, sty, stz). Format: float(24) External: f9.4 NA Value: –1.0 Units: kilometers Range: sminax > 0.0

Name: smoothvalue Table: Fsrecipe Description: Amount of spectral smoothing. Format: float(24) External: f5.2 NA Value: –1.0 Units: Hertz Range: smoothvalue > 0.0

Name: sn_snr Table: Evsc_regional Description: Signal-to-noise ratio of the Sn measurement. Format: float(24) External: f7.2 NA Value: –999.0 Range: sn_snr > 0.0

Database Schema

378 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: snr Table: Amplitude, Apma, Arrival, Complexity, Detection Description: Signal-to-noise ratio. This is an estimate of the ratio of the amplitude of the signal to amplitude of the noise immediately preceding it. For apma, this value is based on the maximum 3-component amplitudes (see amps). This column is the average signal-to-noise ratio for the frequency bands that contrib- uted to the final polarization estimates. Format: float(24) External: f10.2 NA Value: –1.0 Range: snr > 0.0

Name: snr_high_band Table: Evsc_hydro Description: Hydroacoustic signal-to-noise ratio in the high-frequency band (32–64 Hz) from table Amplitude for a given orid/sta pair. Format: float(24) External: f7.2 NA Value: –1.0 Range: snr_high_band > 0.0

Name: snthrsh Table: Siteaux Description: Nominal signal-to-noise ratio. Format: float(24) External: f5.2 NA Value: –1.0 Range: snthrsh > 1.0

Database Schema

IDC-5.1.1Rev5 October 2002 379 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: spike Table: Qcstats Description: Amount of data in the detection processing interval masked due to spikes. Format: float(53) External: f17.5 NA Value: –999.0 Units: seconds Range: spike ≥ 0.0

Name: splitev Table: Ex_an Description: Indicates whether or not the analyst event solution contains arrivals that were previously associated with two or more expert system events. Format: varchar2(4) External: a4 NA Value: - (hyphen) Range: splitev ∈ {y, n}

Name: sproid Table: Detection Description: Uniquely identifies a set of parameters used in the signal processing. Format: number(8) External: i8 NA Value: –1 Range: sproid > 0

Name: src Table: Mig_rules Description: Source database for migration. Format: varchar2(10) External: a10 NA Value: NOT ALLOWED Range: any string up to 10 characters that is a valid name of a database server

Database Schema

380 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: src_dpnt_corr Table: Event_control (In_event_control) Description: Identification of whether or not, and what type of, source-dependent corrections were applied to the location.

0 = No source-dependent corrections applied to the event location. 1 = Test-site travel-time corrections applied to the event location. 2 = Source-Region Station-Timing (SRST) corrections applied to the event location. 3 = Regional level source-specific station corrections (SSSC) applied to the event location. SRST correction is not applied, even if it exists. 4 = Local level SSSCs applied to the location. SRST correction is not applied, even if it exists. Format: number(2) External: i2 NA Value: 0 Range: src_dpnt_corr ∈ {0, 1, 2, 3, 4}

Name: src_tbl Table: Mig_rules Description: Source table for database migration. Format: varchar2(30) External: a30 NA Value: NOT ALLOWED Range: any string up to 30 characters that is a valid table name

Name: srn Table: Origin (Originref, Origin_temp_ga), Sregion Description: Seismic region number, as given in [Fli74] (see grn, grname, and srname). Format: number(8) External: i8 NA Value: –1 NOT ALLOWED for sregion Range: srn > 0

Database Schema

IDC-5.1.1Rev5 October 2002 381 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: srname Table: Sregion Description: Seismic region name. This column is the common name of a seismic region, as given in [Fli74]. Names may have changed due to changing political circumstances (see srn and grname). Format: varchar2(40) External: a40 NA Value: NOT ALLOWED Range: any upper-case string up to 40 characters

Name: sta Table: Affiliation (Stanet), Alphasite, Arrival, Assoc (Assoc_temp_ga), Attencoef, Beamaux, Ceppks, Chan_groups, Complexity, Detection, Dlfile, Evsc_hydro, Evsc_regional, Exception_chanmap, Fileproduct (Fs_stageproduct), Fkdisc, Forbeamaux, Fsave, Fsdisc, Fwfile, Fwgap, Outage, Parrival, Participation, Producttypesta, Qcstats, Request, Sensor, Site, Site_address, Siteaux, Sitechan, Sitepoll, Splp, Stamag, Stassoc, Thirdmom, Timefreq, Wfconv, Wfdisc (Wfproto) Description: Station code. This column value is the code name of a seismic, hydroacoustic, or infrasonic observatory and identifies a geographic location recorded in the site table. Generally only three to five characters are used. Format: varchar2(6) External: a6 NA Value: NOT ALLOWED - (hyphen) for assoc, chan_groups, dlfile, fileproduct, fkdisc, fsdisc, qcstats, stassoc, thirdmom Range: any upper-case string up to six characters

Database Schema

382 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: staname Table: Site Description: Station name/description. This column value is the full name of the station whose codename is in sta. As an example, one record in the site table connects sta = ANMO to staname = ALBUQUERQUE, NEW MEXICO (SRO). Format: varchar2(50) External: a50 NA Value: - (hyphen) Range: any upper-case string up to 50 characters

Name: staper Table: Siteaux Description: Standard period at which noise estimates are made. Format: float(24) External: f5.2 NA Value: –1.0 Units: seconds Range: staper > 0.0

Name: start_time Table: Amplitude, Request Description: Epoch start time of the data interval. Epochal time is given as seconds since hour 0 January 1, 1970. Format: float(53) External: f17.5 NA Value: NOT ALLOWED Units: seconds Range: any valid epoch time

Database Schema

IDC-5.1.1Rev5 October 2002 383 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: stassid Table: Arrival, Stassoc Description: Station association identification. The wavetrain from a single event may be made up of a number of arrivals. A unique stassid joins those arrivals believed to have come from a common event as measured at a single station. Stassid is also the key to the stassoc table, which contains additional signal measurements not contained within the arrival table, such as station magnitude estimates and computed signal characteristics. Format: number(8) External: i8 NA Value: –1 NOT ALLOWED for stassoc Range: stassid > 0

Name: stat_prov Table: Site_address Description: State or province of a country. Format: varchar2(40) External: a40 NA Value: - (hyphen) Range: any string up to 40 characters

Name: state Table: Ga_tag, Interval, Rebdone_dataday_flag, Request Description: Processing state. The processing state of the interval within the automated processing system. Format: varchar2(16) External: a16 varchar2(12) for rebdone_dataday_flag varchar2(20) for ga_tag NA Value: - (hyphen) NOT ALLOWED for ga_tag Range: a set of strings defined at each installation for each automated processing system,

Database Schema

384 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

ga_tag ∈ {aa_processed, analyst_reviewed, assoc_first, driver_restricted, locked_association, probdet_restricted, requested, wc_restricted}

Name: state_count Table: Msgaux Description: Number of failures of the message system to process a request. Format: number(4) External: i4 NA Value: NOT ALLOWED Range: state_count ≥ 0

Name: statecount Table: Request Description: Count of failures. When state = failed, the statecount column records the number of failures to acquire this data. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: statecount ≥ 0

Name: status Table: Dataready, Datauser, Ftpfailed, Msgdatatype, Msgdest, Msgdisc, Outage, Problem, Prodtrack, Subs, Subsuser Description: Status of message (msgdisc), response message (msgdest), or problem (problem). Format: varchar2(32) External: a6 varchar2(8) for dataready, ftpfailed varchar2(6) for subs

Database Schema

IDC-5.1.1Rev5 October 2002 385 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

varchar2(24) for datauser, subsuser varchar2(12) for prodtrack varchar2(33) for problem NA Value: - (hyphen) NOT ALLOWED for datauser Range: any string up to the character limit status ∈ {DONE, FAILED} for msgdatatype status ∈ {ACTIVE, INACTIVE} for datauser

Name: statype Table: Allow_resid, Site, Weights Description: Station type. This character string specifies the station type. Recommended entries are ss (single station) or ar (array). Format: varchar2(4) External: a4 NA Value: - (hyphen) Range: statype ∈ {ss, ar}

Name: stav Table: Detection Description: Short-term average used to describe the amplitude of a signal. The amplitude is averaged over a small time interval, typically 1–2 seconds. This time window is defined in Sigpro processing. Format: float(24) External: f11.5 NA Value: –1.0 Units: nanometers Range: stav > 0.0

Database Schema

386 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: stdconstval Table: Qcstats Description: Standard deviation of data in masked constant segments. Format: float(53) External: f17.5 NA Value: –999.0 Units: same as waveform data Range: stdconstval ≥ 0.0

Name: stime Table: Origerr (Origerr_temp_ga) Description: Origin time error. Format: float(24) external: f8.2 NA Value: –1.0 Units: seconds Range: stime ≥ 0.0

Name: stime Table: Apma, Msgdest Description: In apma, this column is the epoch time at which S-type polarization columns are estimated. The value is the center of the time window with the maximum 3-component amplitude. In msgdest, this column is the time at which the corresponding message was sent. Format: float(53) External: f17.5 NA Value: 9999999999.999 Units: seconds Range: any valid epoch time

Database Schema

IDC-5.1.1Rev5 October 2002 387 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: stmcor Table: Siteaux Description: S-wave arrival time correction. Format: float(24) External: f6.3 NA Value: –999.0 Units: seconds Range: stmcor > –999.0

Name: strike Table: Evsc_prod, Origerr (Origerr_temp_ga) Description: Strike of major axis of error ellipse. This column is the strike of the semi- major axis of the location error ellipse, measured in degrees clockwise from the North (see smajax). Format: float(24) External: f6.2 NA Value: –1.0 Units: degrees Range: 0.0 ≤ strike ≤ 360.0

Name: strip Table: Wfconv Description: Flag showing whether or not the data are stripped of headers (y/n). Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: strip ∈ {n, y}

Database Schema

388 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: stype Table: Arrival Description: Signal type. This single-character flag indicates the event or signal type. The following definitions hold:

l = local event r = regional event t = teleseismic event m = mixed or multiple event g = glitch (for example, non-seismic detection) e = calibration activity obfuscated the data

l, r, and t are supplied by the reporting station or as an output of post-detection processing. g and c come from analyst comment or from status bits from GDSN and RSTN data. Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: stype ∈ {l, r, t, m, g, c}

Name: sub_status Table: Msgaux Description: Cause of failure. Format: varchar2(24) External: a24 NA Value: NOT ALLOWED Range: any string up to 24 characters

Name: subject Table: Msgdisc Description: Subject header from an email message. Format: varchar2(64) External: a64 NA Value: - (hyphen) Range: any string up to 64 characters

Database Schema

IDC-5.1.1Rev5 October 2002 389 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: sublocname Table: Location Description: Sub-location name. Format: varchar2(25) External: a25 NA Value: - (hyphen) Range: any valid string up to 25 characters

Name: subsid Table: Subs Description: Subscription identifier. Format: number(8) External: i8 NA Value: –1 Range: subsid > 0

Name: subsname Table: Subs Description: Subscription name, which is defined by subscriber. Format: varchar2(24) External: a24 NA Value: - (hyphen) Range: any string up to 24 characters

Name: subtype Table: Msgdisc Description: Specification of whether or not the request includes waveforms. In the future, this column may contain indications of other message subtypes. Format: varchar2(2) External: a2 NA Value: - (hyphen) Range: subtype ∈ {V, R, L}

Database Schema

390 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: supressempty Table: Productcriteria Description: Flag (if no) indicating that empty AutoDRM subscription messages should be sent when no data are available. Format: char(2) External: a2 NA Value: - (hyphen) Range: supressempty ∈ {yes, no}

Name: svar Table: Spvar Description: Variance of the detrended log spectrum between fmin and fmax. The spectrum is measured in nm-sec. Format: float(24) External: f12.6 NA Value: NOT ALLOWED Range: any floating point value

Name: sweight Table: Weights Description: Slowness weight. Format: float(24) External: f5.2 NA Value: 0.0 Range: sweight ≥ 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 391 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: sxx, syy, szz, stt, sxy, sxz, syz, stx, sty, stz Table: Origerr (Origerr_temp_ga) Description: Elements of the covariance matrix for the location identified by orid. The covariance matrix is symmetric (and positive definite) so that sxy = syx, and so on, (x, y, z, t) refer to latitude, longitude, depth, and origin time, respectively. These columns (together with sdobs, ndef, and dtype) provide the information necessary to construct the K-dimensional (K = 2, 3, 4) confidence ellipse or ellipsoids at any confidence limit desired. Format: float(24) External: f15.4 NA Value: –1.0 Units: sxx, syy, szz, sxy, szx, syz - kilometers squared (km2) stt - seconds squared (sec2) stx, sty, stz - kilometers per second (km/sec) Range: sxx, syy, szz, stt > 0.0

Name: table_name Table: Arch_data_type Description: Name of table encapsulating the data type. Format: varchar2(32) External: a32 NA Value: - (hyphen) Range: any IDC database table name up to 32 characters

Name: tablename Table: Dataready Description: Database table name containing data ready to be distributed by the Subscrip- tion Subsystem. Format: varchar2(24) External: a24 NA Value: NOT ALLOWED Range: any string up to 24 characters that is a valid table name

Database Schema

392 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: tagid Table: Dataready, Wftag Description: Tagname value. This column contains the value of a foreign key identified in tagname. For example, if tagname is arid, then wftag may be joined to Arrival where arrival.arid = wftag.tagid. If tagname is orid, then wftag and Origin (Originref, Origin_temp_ga) may be joined where origin.orid = wftag.tagid. Format: number(8) External: i10 number(10) for dataready NA Value: NOT ALLOWED Range: tagid > 0

Name: tagid2 Table: Dataready Description: Secondary tag value used by the Subscription Subsystem for data types that require more than one identifier (for example, time range for origin). Format: number(10) External: i10 NA Value: –1 Range: tagid2 > 0

Name: tagname Table: Dataready, Wftag Description: Tagname type. This column value is the name of the foreign key whose value is in tagid. Format: varchar2(8) External: a12 varchar2(12) for dataready NA Value: NOT ALLOWED Range: tagname ∈ {arid, evid, orid, stassid, msgid} for wftag; any for dataready

Database Schema

IDC-5.1.1Rev5 October 2002 393 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: taper Table: Fsrecipe Description: Type of taper used to smooth input data to Fourier spectrum. If cosine is specified, the taperstart and taperend values are used to determine the length of the taper. Format: varchar2(8) External: a8 NA Value: - (hyphen) Range: taper ∈ {hanning, hamming, cosine, bartlet, blackman}

Name: taperend Table: Fsrecipe Description: Length of the ending cosine taper used in smoothing data for Fourier spectra. The value is in percentage of the data window. Format: number(8) External: i3 NA Value: 0 Range: 1 < taperend < 50

Name: taperstart Table: Fsrecipe Description: Length of the starting cosine taper used in smoothing data for Fourier spectra. The value is in percentage of the data window. Format: number(8) External: i3 NA Value: 0 Range: 1 < taperstart < 50

Database Schema

394 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: task_num Table: Mig_rules Description: Order of this migration task. Format: number External: i4 NA Value: NOT ALLOWED Range: task_num ≥ 1

Name: tdepth Table: Location Description: Tunnel depth. This column gives the depth (positive down) of tunnels or other subsites in the location table relative to the value of elev. Format: float(24) External: f9.4 NA Value: –999.0 Units: kilometers Range: tdepth Š 0.0

Name: termination_time Table: Hydro_features Description: Estimated termination time of signal. Format: float(53) External: f17.5 NA Value: –9999999999.999 Units: seconds Range: any valid epoch time

Database Schema

IDC-5.1.1Rev5 October 2002 395 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: testsite Table: Explo Description: Test site region. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any string up to 15 characters

Name: thatdb Table: Xtag Description: Database account for the records specified by thatname and thatid. Format: varchar2(32) External: a32 NA Value: - (hyphen) Range: any character string up to 32 characters that is a valid account name

Name: thatid Table: Xtag Description: Identifier for thatname. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: thatid > 0

Name: thatname Table: Xtag Description: Key for thatid. Format: varchar2(8) External: a8 NA Value: NOT ALLOWED Range: thatname ∈ {arid, orid, wfid …}

Database Schema

396 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: thisdb Table: Xtag Description: Database account for the records specified by thisname and thisid. Format: varchar2(32) External: a32 NA Value: - (hyphen) Range: any character string up to 32 characters that is a valid account name

Name: thisid Table: Xtag Description: Identifier for thisname. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: thisid > 0

Name: thisname Table: Xtag Description: Key for thisid. Format: varchar2(8) External: a8 NA Value: NOT ALLOWED Range: thisname ∈ {arid, orid, wfid …}

Database Schema

IDC-5.1.1Rev5 October 2002 397 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: time Table: Alphasite, Arrival, Beamaux, Datadays, Detection, Dlfile, Fileproduct (Fs_stageproduct), Fkdisc, Fsdisc, Fwgap, Interval, Origin (Originref, Origin_temp_ga), Outage, Parrival, Problem, Problemlog, Qcstats, Sensor, Siteaux, Stassoc, Timestamp, Wfdisc (Wfproto) Description: Epoch time, given as seconds since midnight, January 1, 1970, and stored in a double-precision floating number. time refers to the table in which it is found; for example, in arrival it is the arrival time, in origin it is the origin time, in wfdisc it is the start time of data, and in siteaux it is the start time for which measurements are valid. Where the date of historical events is known, time is set to the start time of that date. Where the date of contemporary arrival measurements is known but no time is given, then time is set to the NA Value. The double-precision floating point number allows 15 decimal digits. At one millisecond accuracy, this is a range of 3 *104 years. Where the date is unknown, or prior to February 10, 1653, time is set to the NA Value. Format: float(53) External: f17.5 number (17, 5) for problem, problemlog NA Value: –9999999999.999 Units: seconds Range: any valid epoch time

Name: time_spread Table: Hydro_features Description: Root-mean-square time spread of the estimated signal energy between onset_time and termination_time. Format: float(24) External: f9.4 NA Value: –1.0 Units: seconds Range: timespread > 0.0

Database Schema

398 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: timedef Table: Assoc (Assoc_temp_ga) Description: Time-defining code. This one-character flag indicates whether or not the time of a phase was used to constrain the event location. This column is defining (timedef = d) or nondefining (timedef = n). Format: varchar2(1) External: a1 NA Value: - (hyphen) Range: timedef ∈ {n, d}

Name: timelastsend Table: Productcriteria Description: Last epoch time that the product was delivered. Format: float(54) External: f17.5 NA Value: –9999999999.999 Units: seconds Range: any valid epoch time

Name: timenextsend Table: Productcriteria Description: Next epoch time that product will be delivered. Format: float(54) External: f17.5 NA Value: –9999999999.999 Units: seconds Range: any valid epoch time

Database Schema

IDC-5.1.1Rev5 October 2002 399 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: timeres Table: Allow_resid, Assoc (Assoc_temp_ga) Description: Time residual. This column is a travel-time residual measured in seconds. The residual is found by taking the observed arrival time (saved in the Arrival table) of a seismic phase and subtracting the expected arrival time. The expected arrival time is calculated by a formula based on an earth velocity model (column vmodel), an event location and origin time (saved in table Ori- gin (Originref, Origin_temp_ga)), the distance to the station (column dist in table assoc), and the particular seismic phase (column phase in table assoc). Format: float(24) External: f8.3 NA Value: –999.0 Units: seconds Range: timeres > –999.0

Name: tlen Table: Ampdescript, Dlfile, Fkdisc, Fsdisc Description: Time window length. Tlen should be NA in ampdescript if a velocity window is used. Format: float(24) External: f10.3 NA Value: –1.0 Units: seconds Range: tlen > 0.0

Name: tmf Table: Thirdmom Description: Third moment of frequency. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: tmf ≥ 0.0

Database Schema

400 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: tmfpct Table: Thirdmom Description: Percentage of signal spectrum amplitudes greater than their corresponding noise spectrum amplitudes in the frequency range [tmf–fmin, tmf–fmax]. tmf– fmin and tmf–fmax are par-file parameters. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: 0 ≤ tmfpct ≤ 100

Name: toff Table: Ampdescript Description: Offset from theoretical or observed arrival time. This column is used to define the start time of the amplitude measurement window and may be used in conjunction with either tlen to define a static window or with gvlo to define a dynamic window. If toff is set to –999, then gvhi must be used to define the start time of the window. Format: float(24) External: f6.2 NA Value: –999.0 Units: seconds Range: toff ≥ 0.0

Name: total_energy Table: Hydro_features, Infra_features Description: Total energy in the signal between onset_time and termination_time for hydro_features and between eng_time and eng_dur for infra_features. Format: float(24) External: f9.4 NA Value: –1.0 Units: dB re µPa (microbars)2 for infra_features Range: total_energy > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 401 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: total_time Table: Hydro_features Description: Total time that the estimated signal pressure squared exceeds noise_onset_thresh between onset_time and termination_time. Format: float(53) External: f17.5 NA Value: –1.0 Units: seconds Range: total_time > 0.0

Name: transmeth Table: Msgdest Description: Method by which the response is to be delivered to the requestor. Format: varchar2(16) External: a16 NA Value: - (hyphen) Range: any string up to 16 characters

Name: tshift Table: Sensor Description: Correction for clock errors. This column is designed to accommodate discrep- ancies between actual time and the numerical time written by data recording systems. Actual time is the sum of the reported time plus tshift. Format: float(24) External: f6.2 NA Value: NOT ALLOWED Units: seconds Range: any valid real number

Database Schema

402 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: tsta Table: Ev_summary (Ex_summary, An_summary) Description: Number of teleseismic observations for an event. A teleseismic observation is currently defined as having a station-event distance ≥ 2000 km. Format: number(8) External: i8 NA Value: –1 Range: tsta ≥ 0

Name: tweight Table: Weights Description: Time weight. Format: float(24) External: f5.2 NA Value: 0.0 Range: tweight ≥ 0.0

Name: typeid Table: Fileproduct (Fs_stageproduct), Fpdescription Description: Identifier for the product type description. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: typeid > 0

Name: uncertainty Table: Netmag, Stamag Description: Magnitude uncertainty. This column value is the standard deviation of the accompanying magnitude measurement. Format: float(24) External: f7.2 NA Value: –1.0 Range: uncertainty > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 403 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: units Table: Amplitude Description: Units of amplitude measure. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: units ∈ {nm}

Name: userid Table: Datauser, Msgdisc, Subs, Subsuser Description: User identifier for Subscription and Message Subsystems. Format: number(8) External: i8 NA Value: –1 NOT ALLOWED for datauser Range: userid > 0

Name: username Table: Datauser, Ftplogin, Subsuser Description: User name for FTP access or for Subscription Subsystem. Format: varchar2(16) External: a24 varchar2(24) for datauser, subuser NA Value: - (hyphen) NOT ALLOWED for datauser Range: any string up to (16, 24) characters that is a valid user name

Name: vamp Table: Amp3c Description: Vertical amplitude. Format: float(24) External: f11.2 NA Value: –999.0 Range: vamp ≥ 0.0

Database Schema

404 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: vang Table: Sitechan Description: Vertical orientation of seismometer. This column measures the angle between the sensitive axis of a seismometer and the outward-pointing vertical direction. For a vertically oriented seismometer, vang = 0. For a horizontally oriented seismometer, vang = 90 (see hang). Format: float(24) External: f6.1 NA Value: NOT ALLOWED Units: degrees Range: 0.0 ≤ vang ≤ 90.0

Name: verifstatus Table: Msgdisc Description: Status of verification. Format: varchar2(4) External: a4 NA Value: - (hyphen) Range: ASCII character string

Name: version Table: Fileproduct (Fs_stageproduct) Description: Version of the software that generated the file product. Format: float(53) External: f6.2 NA Value: –1 Range: version > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 405 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: vmodel Table: Assoc (Assoc_temp_ga), Parrival Description: Velocity model. This character string identifies the velocity model of the earth used to compute the travel times of seismic phases. A velocity model is required for event location (if phase is defining) or for computing travel-time residuals. Format: varchar2(15) External: a15 NA Value: - (hyphen) Range: any string up to 15 characters

Name: vsnr Table: Amp3c Description: Vertical signal-to-noise ratio. Ratio of vamp to root-mean-square amplitude of a vertically-oriented component filtered in a frequency band centered at cfreq Hz. Format: float(24) External: f10.2 NA Value: –999.0 Range: vsnr ≥ 0.0

Name: waterdepth Table: Explo Description: Depth of static water table level. Depth from surface zero to the piezometric surface in pre-Tertiary rocks, or to the composite piezometric surface. Format: float(24) External: f7.4 NA Value: –1 Units: kilometers Range: watdep Š 0.0

Database Schema

406 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: wfid Table: Fsdisc, Wfaux, Wfdisc (Wfproto), Wftag Description: Unique waveform identifier for a wfdisc record. Format: number(8) External: i8 NA Value: –1 Range: wfid > 0

Name: wgt Table: Assoc (Assoc_temp_ga) Description: Location weight. This column gives the final weight assigned to the allied arrival by the location program. This column is used primarily for location programs that adaptively weight data by their residuals. Format: float(24) External: f6.3 NA Value: –1.0 Range: 0.0 ≤ wgt < 1.0

Name: winlen Table: Fsrecipe Description: Number of points per window. Format: number(8) External: i8 NA Value: NOT ALLOWED Range: winlen > 0

Name: xavpct Table: Timefreq Description: Average ratio of bad points to total of the cross-correlation trace. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: 0 ≤ xavpct ≤ 1

Database Schema

IDC-5.1.1Rev5 October 2002 407 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: xcoef Table: Attencoef Description: Constant coefficient in the distance correction formula. Format: float(24) External: f7.2 NA Value: –999.0 Range: any valid floating point value

Name: xcor Table: Timefreq Description: For timefreq, xcor is the zero lag cross-correlation between the three pairs of time-frequency matrices. Format: float(24) External: f9.4 NA Value: NOT ALLOWED Range: 0 ≤ xcor ≤ 1

Name: ycoef Table: Attencoef Description: Geometrical spreading coefficient in the distance correction formula. Format: float(24) External: f7.2 NA Value: –999.0 Range: any valid floating point value

Name: yield Table: Explo Description: Explosion yield. Format: float(24) External: f9.3 NA Value: –1 Units: kT Range: yield > 0.0

Database Schema

408 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: yldmax Table: Explo Description: Estimated upper limit of explosion yield. Format: float(24) External: f9.3 NA Value: –1 Units: kT Range: yldmax > 0.0

Name: zavcep Table: Timefreq Description: Average maximum value in the two-dimensional cepstrum of the vertical component traces. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: zavcep ≥ 0

Name: zavcor Table: Timefreq Description: Average autocorrelation along the time axis across all frequencies excluding randomized points of the vertical component traces. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: zavcor ≥ 0

Database Schema

IDC-5.1.1Rev5 October 2002 409 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Name: zavpct Table: Timefreq Description: Average ratio of bad points to total of the vertical component traces. Format: float(24) External: f7.2 NA Value: NOT ALLOWED Range: 0 ≤ zavpct ≤ 1

Name: zcoef Table: Attencoef Description: Attenuation coefficient in the distance correction formula. Format: float(24) External: f7.2 NA Value: –999.0 Range: any valid floating point value

Name: zrcr_delfreq Table: Infra_features Description: The estimated standard deviation in zrcr_freq. Format: float(24) External: f7.2 NA Value: –1.0 Units: Hertz Range: zcr_delfreq > 0.0

Database Schema

410 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 3:

S/H/I Column Descriptions ▼

Name: zrcr_freq Table: Infra_features Description: Frequency of the arrival as estimated from the zero-crossing rate of the traditional beam-formed waveform data in the time interval defined by coinc_time and coinc_dur. Format: float(24) External: f7.2 NA Value: –1.0 Units: Hertz Range: zcr_freq > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 411 IDC DOCUMENTATION Chapter 3: User Guides

▼ S/H/I Column Descriptions

Database Schema

412 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

Chapter 4: Radionuclide Database Overview

This chapter describes the organization of the radionuclide database schema. The following topics are covered:

■ Two-tier Database Schema

■ Database Organization

■ Radionuclide Object Descriptions

Database Schema

IDC-5.1.1Rev5 October 2002 413 IDC DOCUMENTATION User Guides

Chapter 4: Radionuclide Database Overview

TWO-TIER DATABASE SCHEMA

A two-tiered database is set up for analysis of IMS radionuclide data. One database is used for automatic analysis of sample data as they arrive. This database is owned by the user RMSAUTO. The second database is used for interactive analysis by the IDC radionuclide analysts. This database is owned by the user RMSMAN. A two-tiered database schema is used to preserve both the automatic analysis results and the interactive analysis results without one overwriting the other. All of the operations that the automatic pipeline performs effect changes in the RMSAUTO database. All operations that an analyst performs effect changes in the RMSMAN database.

DATABASE ORGANIZATION

The radionuclide database tables are conceptually organized into four groups. These groups are described in this section.

Raw Data Tables (raw)

Raw data tables are tables that hold the original data received from the reporting stations. The RMSAUTO user owns these tables, but the RMSMAN user has permission to read the tables. RMSMAN creates synonyms for each table to facilitate queries.

Database Schema

414 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼

Static Data Tables (static)

The static tables hold data about detectors, stations, and tables used as the default processing parameters for sample data analysis. The RMSMAN user owns these tables, but the RMSAUTO user has permission to read the tables. RMSAUTO creates synonyms for each table to facilitate queries.

Analysis Data Tables (analysis)

Analysis tables hold the results of the analysis processing. Both the RMSAUTO and RMSMAN users own versions of these tables. The RMSMAN user is not permitted to make a change to the RMSAUTO analysis data tables, but the RMSAUTO user is permitted to make a change to the RMSMAN analysis data tables. Analysis data are com- piled first in RMSAUTO and are moved to RMSMAN by triggers. There are three triggers for each analysis data table; one each for insert, update, and delete. These triggers keep the RMSAUTO analysis data tables in sync during automatic analysis. After a record is inserted, updated, or deleted in the RMSAUTO version of these tables, a database trigger copies the change to the RMSMAN version of the tables.

Independent Data Tables (indy)

Both the RMSAUTO and RMSMAN users own versions of these tables. Unlike the analysis tables, there are no triggers between the two versions of independent tables. These tables are owned by the two users and are unrelated to each other. Independent tables are used to hold the results of tests and analysis performed within the current user’s objects.

Table 123 provides a complete listing of the Release 3 database tables and the group to which each table belongs. The third column indicates whether changes were made since the last release of the software (Release 2.1).

Database Schema

IDC-5.1.1Rev5 October 2002 415 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

TABLE 123:DATABASE TABLE GROUPS

Table Name Table Group Changes

debug indy unchanged

gards_alerts raw unchanged

gards_aux_lib static unchanged

gards_aux_lines_lib static unchanged

gards_b_energy_pairs analysis unchanged

gards_b_energy_pairs_orig analysis unchanged

gards_b_resolution_pairs analysis unchanged

gards_b_resolution_pairs_orig analysis unchanged

gards_bg_efficiency_pairs analysis unchanged

gards_bg_energy_cal analysis new

gards_cat_template analysis new

gards_codes static unchanged

gards_comments analysis modified

gards_comments_defs static modified

gards_data_log raw modified

gards_dbrole_owner static new

gards_detectors static unchanged

gards_dist_sample_queue static unchanged

gards_efficiency_cal analysis unchanged

gards_efficiency_pairs analysis unchanged

gards_energy_cal analysis unchanged

gards_energy_cal_orig analysis unchanged

gards_energy_pairs analysis unchanged

gards_energy_pairs_orig analysis unchanged

gards_environment raw unchanged

Database Schema

416 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼

TABLE 123:DATABASE TABLE GROUPS (CONTINUED)

Table Name Table Group Changes

gards_flags indy unchanged

gards_fpe indy unchanged

gards_histogram raw unchanged

gards_interval raw unchanged

gards_mdas2report static unchanged

gards_met_data raw unchanged

gards_notify static unchanged

gards_nucl_ided analysis unchanged

gards_nucl_ided_orig analysis unchanged

gards_nucl_lib static unchanged

gards_nucl_lines_ided analysis unchanged

gards_nucl_lines_ided_orig analysis unchanged

gards_nucl_lines_lib static unchanged

gards_nucl2quantify static unchanged

gards_peaks analysis unchanged

gards_peaks_orig analysis unchanged

gards_permissions static modified

gards_poc static unchanged

gards_proc_params_template static unchanged

gards_qchistory analysis unchanged

gards_qcparams static unchanged

gards_qctargets static unchanged

gards_query_results indy unchanged

gards_receipt_log raw unchanged

gards_refline_master static unchanged

Database Schema

IDC-5.1.1Rev5 October 2002 417 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

TABLE 123:DATABASE TABLE GROUPS (CONTINUED)

Table Name Table Group Changes

gards_relevant_nuclides static unchanged

gards_resolution_cal analysis unchanged

gards_resolution_cal_orig analysis unchanged

gards_resolution_pairs analysis unchanged

gards_resolution_pairs_orig analysis unchanged

gards_rlr raw unchanged

gards_roi_channels analysis unchanged

gards_roi_concs analysis unchanged

gards_roi_counts analysis unchanged

gards_roi_lib static unchanged

gards_roi_limits analysis unchanged

gards_roles static modified

gards_roles_permissions static unchanged

gards_sample_aux raw unchanged

gards_sample_cert raw unchanged

gards_sample_cert_lines raw unchanged

gards_sample_data analysis unchanged

gards_sample_description raw unchanged

gards_sample_flags analysis unchanged

gards_sample_proc_params analysis unchanged

gards_sample_ratios analysis unchanged

gards_sample_status analysis unchanged

gards_sample_update_params analysis unchanged

gards_sample_xe_proc_params analysis modified

gards_soh_char_data raw new

Database Schema

418 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼

TABLE 123:DATABASE TABLE GROUPS (CONTINUED)

Table Name Table Group Changes

gards_soh_code static modified

gards_soh_header raw unchanged

gards_soh_num_data raw new

gards_soh_sensor_data raw new

gards_spectrum raw unchanged

gards_stadet static unchanged

gards_station_assignments static unchanged

gards_stations static unchanged

gards_stations_schedule static unchanged

gards_total_effic analysis unchanged

gards_trendvue indy unchanged

gards_update_params_template static unchanged

gards_update_reflines static unchanged

gards_user_comments analysis modified

gards_userenv static unchanged

gards_users static modified

gards_users_roles static modified

gards_xe_nucl_lib static unchanged

gards_xe_nucl_lines_lib static unchanged

gards_xe_proc_params_template static modified

RADIONUCLIDE OBJECT DESCRIPTIONS

This chapter describes the objects in the IDC Radionuclide Schema (other than tables), for both the RMSAUTO database and the RMSMAN database. The table descriptions follow in a subsequent chapter.

Database Schema

IDC-5.1.1Rev5 October 2002 419 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

Links to other Databases and Tables

Four objects reside outside the two-tiered database schema, which are of interest to radionuclide processing. These objects are lastid, fileproduct, fpdescription, and msgdisc. These objects are related to incoming message processing and are owned by the IDCX user (see the “S/H/I Table Descriptions” section for details). Synonyms created by the RMSAUTO and RMSMAN users establish a connection to these objects. The IDCX user grants permission to the RMSAUTO and RMSMAN users to allow updates to the objects.

Description of RMSAUTO Objects

Tables 124–130 fully describe all of the RMSAUTO user’s objects (other than tables).

TABLE 124:RMSAUTO INDEXES

Table Name Index Name Indexed Columns

gards_comments comments_ndx analyst, sample_id

gards_data_log data_log_ndx data_type, station_id, status

gards_efficiency_cal efficiency_cal_ndx sample_id

gards_efficiency_pairs efficiency_pairs_ndx sample_id

gards_energy_cal energy_cal_ndx sample_id

gards_energy_cal_orig energy_cal_orig_ndx sample_id

gards_energy_pairs energy_pairs_ndx sample_id

gards_energy_pairs_orig energy_pairs_orig_ndx sample_id

gards_environment environment_ndx sample_id

gards_met_data met_data_ndx end_time, start_time, station_id

gards_nic nic_ndx sample_id

gards_nucl_lines_ided nucl_lines_ided_ndx name, peak_sample_id

gards_nucl_lines_ided_orig nucl_lines_ided_orig_ndx name, peak_sample_id

Database Schema

420 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼

TABLE 124:RMSAUTO INDEXES (CONTINUED)

Table Name Index Name Indexed Columns

gards_peaks peaks_ndx energy, ided, peak_id, sample_id

gards_peaks_orig peaks_orig_ndx energy, ided, peak_id, sample_id

gards_qchistory qchistory_ndx sample_id

gards_resolution_cal resolution_cal_ndx sample_id

gards_resolution_cal_orig resolution_cal_orig_ndx sample_id

gards_resolution_pairs resolution_pairs_ndx sample_id

gards_resolution_pairs_orig resolution_pairs_orig_ndx sample_id

gards_sample_cert sample_cert_ndx sample_id

gards_sample_cert_lines sample_cert_lines_ndx sample_id

gards_sample_data sample_data_ndx collect_stop, data_type, detector_id, sample_type, spectral_qualifier, station_id

gards_sample_flags sample_flags_ndx sample_id

gards_sample_proc_params sample_proc_params_ndx sample_id

gards_sample_status sample_status_ndx sample_id, status

gards_sample_update_params sample_update_params_ndx sample_id

gards_soh_num_data soh_num_data_ndx station_id, dtg_begin, dtg_end, param_code

gards_soh_char_data soh_char_data_ndx station_id, dtg_begin, dtg_end, param_code

gards_total_effic total_effic_ndx sample_id

gards_user_comments user_comments_ndx comment_id

Database Schema

IDC-5.1.1Rev5 October 2002 421 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

TABLE 125:RMSAUTO UNIQUE DATA CONSTRAINTS

Table Name Index Name Constraint Column Names

gards_sample_data uq_sample_data acquisition_stop, collect_stop, detector_id, spectral_qualifier, station_id

TABLE 126:RMSAUTO PRIMARY KEY CONSTRAINTS

Table Name Index Name Constraint Column Names

gards_comments pk_comments comment_id

gards_flags pk_flags flag_id

gards_nucl_ided pk_nucl_ided name, sample_id

gards_nucl_ided_orig pk_nucl_ided_orig name, sample_id

gards_sample_aux pk_sample_aux sample_id

gards_sample_data pk_sample_data sample_id

gards_sample_description pk_sample_description sample_id

gards_sample_status pk_sample_status sample_id

TABLE 127:RMSAUTO FOREIGN KEY CONSTRAINTS

Foreign Table Name. Table Name Constraint Name Column Name

gards_bg_efficiency_pairs fk_bg_efficiency_pairs gards_sample_data. sample_id

gards_bg_energy_cal fk_bg_en_cal_sid gards_sample_data. (sample_id)

gards_b_energy_pairs fk_b_energy_pairs gards_sample_data. sample_id

gards_b_energy_pairs_orig fk_b_energy_pairs_orig gards_sample_data. sample_id

Database Schema

422 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼

TABLE 127:RMSAUTO FOREIGN KEY CONSTRAINTS (CONTINUED)

Foreign Table Name. Table Name Constraint Name Column Name

gards_b_resolution_pairs fk_b_resolution_pairs gards_sample_data. sample_id

gards_b_resolution_pairs_orig fk_b_resolution_pairs_orig gards_sample_data. sample_id

gards_comments fk_comments gards_sample_data. sample_id

gards_efficiency_cal fk_efficiency_cal gards_sample_data. sample_id

gards_efficiency_pairs fk_efficiency_pairs gards_sample_data. sample_id

gards_energy_cal fk_energy_cal gards_sample_data. sample_id

gards_energy_cal_orig fk_energy_cal_orig gards_sample_data. sample_id

gards_energy_pairs fk_energy_pairs gards_sample_data. sample_id

gards_energy_pairs_orig fk_energy_pairs_orig gards_sample_data. sample_id

gards_environment fk_environment gards_sample_data. sample_id

gards_fpe fk_fpe gards_sample_data. sample_id

gards_histogram fk_histogram gards_sample_data. sample_id

gards_nic fk_nic gards_sample_data. sample_id

gards_nucl_ided fk_nucl_ided gards_sample_data. sample_id

gards_nucl_ided_orig fk_nucl_ided_orig gards_sample_data. sample_id

Database Schema

IDC-5.1.1Rev5 October 2002 423 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

TABLE 127:RMSAUTO FOREIGN KEY CONSTRAINTS (CONTINUED)

Foreign Table Name. Table Name Constraint Name Column Name

gards_nucl_lines_ided fk_nucl_lines_ided gards_sample_data. sample_id

gards_nucl_lines_ided_orig fk_nucl_lines_ided_orig gards_sample_data. sample_id

gards_peaks fk_peaks gards_sample_data. sample_id

gards_peaks_orig fk_peaks_orig gards_sample_data. sample_id

gards_qchistory fk_qchistory gards_sample_data. sample_id

gards_resolution_cal fk_resolution_cal gards_sample_data. sample_id

gards_resolution_cal_orig fk_resoultion_cal_orig gards_sample_data. sample_id

gards_resolution_pairs fk_resolution_pairs gards_sample_data. sample_id

gards_resolution_pairs_orig fk_resolution_pairs_orig gards_sample_data. sample_id

gards_roi_channels fk_roi_channels gards_sample_data. sample_id

gards_roi_concs fk_roi_concs gards_sample_data. sample_id

gards_roi_counts fk_roi_counts gards_sample_data. sample_id

gards_roi_limits fk_roi_limits gards_sample_data. sample_id

gards_sample_aux fk_sample_aux gards_sample_data. sample_id

gards_sample_cert fk_sample_cert gards_sample_data. sample_id

Database Schema

424 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼

TABLE 127:RMSAUTO FOREIGN KEY CONSTRAINTS (CONTINUED)

Foreign Table Name. Table Name Constraint Name Column Name

gards_sample_cert_lines fk_sample_cert_lines gards_sample_data. sample_id

gards_sample_description fk_sample_description gards_sample_data. sample_id

gards_sample_flags fk_sample_flags gards_sample_data. sample_id

gards_sample_proc_params fk_sample_proc_params gards_sample_data. sample_id

gards_sample_ratios fk_sample_ratios gards_sample_data. sample_id

gards_sample_status fk_sample_status gards_sample_data. sample_id

gards_sample_update_params fk_sample_update_params gards_sample_data. sample_id

gards_sample_xe_proc_params fk_sample_xe_proc_params gards_sample_data. sample_id

gards_spectrum fk_spectrum gards_sample_data. sample_id

gards_total_effic fk_total_effic gards_sample_data. sample_id

gards_user_comments fk_user_comments gards_comments. comment_id

Database Schema

IDC-5.1.1Rev5 October 2002 425 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

TABLE 128:RMSAUTO COLUMN CONSTRAINTS

Table Name Constrained Columns Constraint Type

gards_interval class, name not null

gards_nucl_ided detector_id, sample_id, not null station_id

gards_nucl_ided_orig detector_id, sample_id, not null station_id

gards_nucl_lines_ided detector_id, sample_id, not null station_id

gards_nucl_lines_ided_orig detector_id, sample_id, not null station_id

gards_receipt_log pocid, prodid, subid, type not null

TABLE 129:RMSAUTO SYNONYMS

Synonym Name Owner Object Name Object Type

fileproduct IDCX fileproduct table

fpdescription IDCX fpdescription table

gards_aux_lib RMSMAN gards_aux_lib table

gards_aux_lines_lib RMSMAN gards_aux_lines_lib table

gards_cat_template RMSMAN gards_cat_template table

gards_codes RMSMAN gards_codes table

gards_comments_defs RMSMAN gards_comments_defs table

gards_comments_seq RMSMAN gards_comments_seq sequence

gards_detectors RMSMAN gards_detectors table

gards_detector_id RMSMAN gards_detector_id sequence

gards_dist_sample_queue RMSMAN gards_dist_sample_queue table

gards_dl_id_seq RMSMAN gards_dl_id_seq sequence

Database Schema

426 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼

TABLE 129:RMSAUTO SYNONYMS (CONTINUED)

Synonym Name Owner Object Name Object Type

gards_fpid_seq RMSMAN gards_fpid_seq sequence

gards_mdas2report RMSMAN gards_mdas2report table

gards_method_id_seq RMSMAN gards_method_id_seq sequence

gards_nic_init RMSMAN gards_nic_init table

gards_notify RMSMAN gards_notify table

gards_nucl2quantify RMSMAN gards_nucl2quantify table

gards_nucl_lib RMSMAN gards_nucl_lib table

gards_nucl_lines_lib RMSMAN gards_nucl_lines_lib table

gards_permissions RMSMAN gards_permissions table

gards_perm_id_seq RMSMAN gards_perm_id_seq sequence

gards_poc RMSMAN gards_poc table

gards_pocid_seq RMSMAN gards_pocid_seq sequence

gards_proc_params_template RMSMAN gards_proc_params_ table template

gards_prcessing_errors RMSMAN gards_processing_errors table

gards_qcparams RMSMAN gards_qcparams table

gards_qctargets RMSMAN gards_qctargets table

gards_qviewer_seq RMSMAN gards_qviewer_seq sequence

gards_read_sample_cat RMSMAN gards_sample_cat table

gards_refline_master RMSMAN gards_refline_master table

gards_relevant_nuclides RMSMAN gards_relevant_nuclides table

gards_rlr_seq RMSMAN gards_rlr_seq sequence

gards_roi_lib RMSMAN gards_roi_lib table

gards_role_id_seq RMSMAN gards_role_id_seq sequence

gards_roles RMSMAN gards_roles table

gards_roles_permissions RMSMAN gards_roles_permissions table

Database Schema

IDC-5.1.1Rev5 October 2002 427 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

TABLE 129:RMSAUTO SYNONYMS (CONTINUED)

Synonym Name Owner Object Name Object Type

gards_sample_cat RMSMAN gards_sample_cat table

gards_sample_id_seq RMSMAN gards_sample_id_seq sequence

gards_soh_code RMSMAN gards_soh_code table

gards_soh_id_seq RMSMAN gards_soh_id_seq sequence

gards_stadet RMSMAN gards_stadet table

gards_stations RMSMAN gards_stations table

gards_stations_schedule RMSMAN gards_stations_schedule table

gards_station_assignments RMSMAN gards_station_assignments table

gards_station_id RMSMAN gards_station_id sequence

gards_update_params_ RMSMAN gards_update_params_ table template template

gards_update_reflines RMSMAN gards_update_reflines table

gards_user_id_seq RMSMAN gards_user_id_seq sequence

gards_userenv RMSMAN gards_userenv table

gards_users RMSMAN gards_users table

gards_users_roles RMSMAN gards_users_roles table

gards_write_sample_cat RMSAUTO gards_auto_sample_cat table

gards_xe_nucl_lib RMSMAN gards_xe_nucl_lib table

gards_xe_nucl_lines_lib RMSMAN gards_xe_nucl_lines_lib table

gards_xe_proc_params_ RMSMAN gards_xe_proc_params_ table template template

gsd RMSAUTO gards_sample_data table

gss RMSAUTO gards_sample_status table

interval RMSAUTO gards_interval table

lastid IDCX lastid view

msgdisc IDCX msgdisc table

Database Schema

428 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼ tion_pairs_orig RMSMAN Tables Updated Tables RMSMAN gards_bg_efficiency_pairs gards_b_energy_pairs gards_b_energy_pairs_orig gards_b_resolution_pairs gards_b_resolu gards_comments gards_efficiency_cal gards_efficiency_pairs Type/Event after insert, update, or delete after insert, update_or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete gy_pairs_orig

Table Name gards_bg_efficiency_pairs gards_b_energy_pairs gards_b_ener gards_b_resolution_pairs gards_b_resolution_pairs_orig gards_comments gards_efficiency_cal gards_efficiency_pairs RIGGERS 130:RMSAUTO T Trigger Name bg_efficiency_pairs_i_u_d b_energy_pairs_i_u_d b_energy_pairs_orig_i_u_d b_resolution_pairs_i_u_d b_resolution_pairs_orig_i_u_d comments_i_u_d efficiency_cal_i_u_d efficiency_pairs_i_u_d ABLE T

Database Schema

IDC-5.1.1Rev5 October 2002 429 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview gards_energy_cal gards_energy_cal_orig gards_energy_pairs gards_energy_pairs_orig gards_bg_energy_cal gards_sample_cat gards_nucl_ided gards_nucl_ided_orig after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete ) CONTINUED ( gards_energy_cal gards_energy_cal_orig gards_energy_pairs gards_energy_pairs_orig gards_bg_energy_cal gards_sample_cat gards_nucl_ided gards_nucl_ided_orig RIGGERS 130:RMSAUTO T Trigger NameTrigger energy_cal_i_u_d energy_cal_orig_i_u_d Name Table energy_pairs_i_u_d energy_pairs_orig_i_u_d Type/Eventgards_bg_energy_cal_i_u_d Updated Tables RMSMAN gards_sample_cat_i_u_d nucl_ided_i_u_d nucl_ided_orig_i_u_d ABLE T

Database Schema

430 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼ gards_nucl_lines_ided gards_nucl_lines_ided_orig gards_peaks gards_peaks_orig gards_qchistory gards_resolution_cal gards_resolution_pairs gards_resolution_cal_orig after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete ) nes_ided_orig CONTINUED ( gards_nucl_lines_ided gards_nucl_li gards_peaks gards_peaks_orig gards_qchistory gards_resolution_cal gards_resolution_pairs gards_resolution_cal_orig RIGGERS 130:RMSAUTO T Trigger NameTrigger nucl_lines_ided_i_u_d nucl_lines_ided_orig_i_u_d Name Table peaks_i_u_d peaks_orig_i_u_d Type/Eventqchistory_i_u_d Updated Tables RMSMAN resolution_cal_i_u_d resolution_pairs_i_u_d res_cal_orig_i_u_d ABLE T

Database Schema

IDC-5.1.1Rev5 October 2002 431 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview gards_resolution_pairs_orig gards_roi_channels gards_roi_concs gards_roi_counts gards_roi_limits gards_sample_data gards_sample_flags gards_sample_proc_params after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete ) CONTINUED ( gards_resolution_pairs_orig gards_roi_channels gards_roi_concs gards_roi_counts gards_roi_limits gards_sample_data gards_sample_flags gards_sample_proc_params RIGGERS 130:RMSAUTO T Trigger NameTrigger res_pairs_orig_i_u_d roi_channels_i_u_d Name Table roi_concs_i_u_d roi_counts_i_u_d Type/Eventroi_limits_i_u_d Updated Tables RMSMAN sample_data_i_u_d sample_flags_i_u_d sample_proc_params_i_u_d ABLE T

Database Schema

432 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼ gards_sample_ratios gards_sample_status gards_sample_update_params gards_sample_xe_proc_params gards_total_effic gards_user_comments after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete after insert, update, or delete ) CONTINUED ( gards_sample_ratios gards_sample_status gards_sample_update_params gards_sample_xe_proc_params gards_total_effic gards_user_comments RIGGERS fully describe all of the RMSMAN user’s objects (other than tables). (other than objects user’s of the RMSMAN all describe fully 138 – 130:RMSAUTO T 131 Trigger NameTrigger sample_ratios_i_u_d sample_status_i_u_d Name Table sample_update_params_i_u_d sample_xe_proc_params_i_u_d Type/Eventtotal_effic_i_u_d Updated Tables RMSMAN user_comments_i_u_d ABLE T Tables Description of RMSMAN Objects of RMSMAN Description

Database Schema

IDC-5.1.1Rev5 October 2002 433 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

TABLE 131:RMSMAN INDEXES

Table Name Index Name Indexed Columns

gards_comments comments_ndx analyst, sample_id

gards_efficiency_cal efficiency_cal_ndx sample_id

gards_efficiency_pairs efficiency_pairs_ndx sample_id

gards_energy_cal energy_cal_ndx sample_id

gards_energy_cal_orig energy_cal_orig_ndx sample_id

gards_energy_pairs energy_pairs_ndx sample_id

gards_energy_pairs_orig energy_pairs_orig_ndx sample_id

gards_nic nic_ndx sample_id

gards_nucl_lines_ided nucl_lines_ided_ndx name, peak, sample_id

gards_nucl_lines_ided_orig nucl_lines_ided_orig_ndx name, peak, sample_id

gards_peaks peaks_ndx energy, ided, peak_id, sample_id

gards_peaks_orig peaks_orig_ndx sample_id

gards_qchistory qchistory_ndx sample_id

gards_resolution_cal resolution_cal_ndx sample_id

gards_resolution_cal_orig resolution_ndx sample_id

gards_resolution_pairs resolution_pairs_ndx sample_id

gards_resolution_pairs_orig resolution_pairs_orig_ndx sample_id

gards_sample_data sample_data_ndx collect_stop, data_type, detector_id, sample_type, spectral_qualifier, station_id

gards_sample_flags sample_flags_ndx sample_id

gards_sample_proc_params sample_proc_params_ndx sample_id

gards_sample_status sample_status_ndx sample_id, status

Database Schema

434 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼

TABLE 131:RMSMAN INDEXES (CONTINUED)

Table Name Index Name Indexed Columns

gards_sample_update_params sample_update_params_ndx sample_id

gards_total_effic total_effic_ndx sample_id

gards_user_comments user_comments_ndx comment_id

TABLE 132:RMSMAN UNIQUE DATA CONSTRAINTS

Table Name Index Name Constraint Column Names

gards_dbrole_owner gards_dbrole_single owner

gards_detectors uq_detectors detector_code

gards_sample_data uq_sample_data acquisition_stop, collect_stop, detector_id, spectral_qualifier, station_id

gards_stations uq_stations station_code

gards_userenv uq_userenv name

TABLE 133:RMSMAN PRIMARY KEY CONSTRAINTS

Table Name Constraint Name Constraint Column Names

gards_comments pk_comments comment_id

gards_detectors pk_detectors detector_id

gards_dist_sample_queue pk_dist_sample_queue sample_id

gards_flags pk_flags flag_id

gards_nucl_ided pk_nucl_ided name, sample_id

gards_nucl_ided_orig pk_nucl_ided_orig name, sample_id

gards_stations pk_stations station_id

gards_poc pk_poc pocid

gards_sample_data pk_sample_data sample_id

Database Schema

IDC-5.1.1Rev5 October 2002 435 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

TABLE 133:RMSMAN PRIMARY KEY CONSTRAINTS (CONTINUED)

Table Name Constraint Name Constraint Column Names

gards_sample_status pk_sample_status sample_id

gards_permissions pk_permissions permission_id

gards_roles pk_roles role_id

gards_users pk_users user_id

TABLE 134:RMSMAN FOREIGN KEY CONSTRAINTS

Foreign Table Name. Table Name Constraint Name Column Name

gards_b_energy_pairs fk_b_energy_pairs gards_sample_data.sample_id

gards_b_energy_pairs_orig fk_b_energy_pairs_orig gards_sample_data.sample_id

gards_b_resolution_pairs fk_b_resolution_pairs gards_sample_data.sample_id

gards_b_resolution_pairs_ fk_b_resolution_pairs_ gards_sample_data.sample_id orig orig

gards_bg_efficiency_pairs fk_bg_efficiency_pairs gards_sample_data.sample_id

gards_bg_energy_cal fk_bg_en_cal_sid gards_sample_data.sample_id

gards_comments fk_comments gards_sample_data.sample_id

gards_dist_sample_queue fk_dist_sample_queue gards_sample_data.sample_id

gards_efficiency_cal fk_efficiency_cal gards_sample_data.sample_id

gards_efficiency_pairs fk_efficiency_pairs gards_sample_data.sample_id

gards_energy_cal fk_energy_cal gards_sample_data.sample_id

gards_energy_cal_orig fk_energy_cal_orig gards_sample_data.sample_id

gards_energy_pairs fk_energy_pairs gards_sample_data.sample_id

gards_energy_pairs_orig fk_energy_pairs_orig gards_sample_data.sample_id

gards_fpe fk_fpe gards_sample_data.sample_id

gards_nic fk_nic gards_sample_data.sample_id

Database Schema

436 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼

TABLE 134:RMSMAN FOREIGN KEY CONSTRAINTS (CONTINUED)

Foreign Table Name. Table Name Constraint Name Column Name

gards_nucl_ided fk_nucl_ided gards_sample_data.sample_id

gards_nucl_ided_orig fk_nucl_ided_orig gards_sample_data.sample_id

gards_nucl_lines_ided fk_nucl_lines_ided gards_sample_data.sample_id

gards_nucl_lines_ided_orig fk_nucl_lines_ided_orig gards_sample_data.sample_id

gards_peaks fk_peaks gards_sample_data.sample_id

gards_peaks_orig fk_peaks_orig gards_sample_data.sample_id

gards_qchistory fk_qchistory gards_sample_data.sample_id

gards_resolution_cal fk_resolution_cal gards_sample_data.sample_id

gards_resolution_cal_orig fk_resoultion_cal_orig gards_sample_data.sample_id

gards_resolution_pairs fk_resolution_pairs gards_sample_data.sample_id

gards_resolution_pairs_orig fk_resolution_pairs_orig gards_sample_data.sample_id

gards_roi_channels fk_roi_channels gards_sample_data.sample_id

gards_roi_concs fk_roi_concs gards_sample_data.sample_id

gards_roi_counts fk_roi_counts gards_sample_data.sample_id

gards_roi_limits fk_roi_limits gards_sample_data.sample_id

gards_sample_flags fk_sample_flags gards_sample_data.sample_id

gards_sample_proc_params fk_sample_proc_params gards_sample_data.sample_id

gards_sample_ratios fk_sample_ratios gards_sample_data.sample_id

gards_sample_status fk_sample_status gards_sample_data.sample_id

gards_sample_update_ fk_sample_update_ gards_sample_data.sample_id params params

gards_sample_xe_proc_ fk_sample_xe_proc_ gards_sample_data.sample_id params params

gards_station_assignments fk_station_assignments gards_stations.station_id

gards_total_effic fk_total_effic gards_sample_data.sample_id

gards_user_comments fk_user_comments gards_sample_data.sample_id

Database Schema

IDC-5.1.1Rev5 October 2002 437 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

TABLE 135:RMSMAN COLUMN CONSTRAINTS

Table Name Constrained Columns Constraint Type

gards_notify dtg_begin, event not null

gards_nucl_ided detector_id, sample_id, station_id not null

gards_nucl_ided_orig detector_id, sample_id, station_id not null

gards_nucl_lines_ided detector_id, sample_id, station_id not null

gards_nucl_lines_ided_orig detector_id, sample_id, station_id not null

gards_poc email_address not null

TABLE 136:RMSMAN SEQUENCES

Sequence Name Sequenced Table Name

gards_comments_seq gards_comments

gards_detector_id gards_detectors

gards_dl_id_seq gards_data_log

gards_fpid_seq gards_fpe

gards_method_id_seq gards_cat_template

gards_perm_id_seq gards_permissions

gards_pocid_seq gards_poc

gards_qviewer_seq gards_trendvue

gards_rlr_seq gards_rlr

gards_role_id_seq gards_roles

gards_sample_id_seq gards_sample_data

gards_soh_id_seq gards_soh_header

gards_station_id gards_stations

gards_user_id_seq gards_users

Database Schema

438 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 4:

Radionuclide Database Overview ▼

TABLE 137:RMSMAN SYNONYMS

Synonym Name Table Owner Table Name Object Type

fileproduct IDCX fileproduct table

fpdescription IDCX fpdescription table

gards_alerts RMSAUTO gards_alerts table

gards_data_log RMSAUTO gards_data_log table

gards_environment RMSAUTO gards_environment table

gards_histogram RMSAUTO gards_histogram table

gards_interval RMSAUTO gards_interval table

gards_met_data RMSAUTO gards_met_data table

gards_read_sample_cat RMSMAN gards_sample_cat table

gards_receipt_log RMSAUTO gards_receipt_log table

gards_rlr RMSAUTO gards_rlr table

gards_sample_aux RMSAUTO gards_sample_aux table

gards_sample_cert RMSAUTO gards_sample_cert table

gards_sample_cert_lines RMSAUTO gards_sample_cert_lines table

gards_sample_description RMSAUTO gards_sample_description table

gards_soh_char_data RMSAUTO gards_soh_char_data table

gards_soh_header RMSAUTO gards_soh_header table

gards_soh_num_data RMSAUTO gards_soh_num_data table

gards_soh_sensor_data RMSAUTO gards_soh_sensor_data table

gards_spectrum RMSAUTO gards_spectrum table

gards_write_sample_cat RMSMAN gards_sample_cat table

gsd RMSMAN gards_sample_data table

gss RMSMAN gards_sample_status table

lastid IDCX lastid view

msgdisc IDCX msgdisc table

Database Schema

IDC-5.1.1Rev5 October 2002 439 IDC DOCUMENTATION Chapter 4: User Guides

▼ Radionuclide Database Overview

TABLE 138:RMSMAN TRIGGERS

Trigger Name Table Name Type/Event Tables Updated

sample_data_insert gards_sample_data after insert gards_stadet

sample_status_update gards_sample_status after update gards_fpe

stations_insert gards_stations after insert gards_station_ assignments

Database Schema

440 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

Chapter 5: Radionuclide Entity Relationships

This chapter describes the relationships between selected tables for the IDC radionuclide database schema. The following topics are covered:

■ Overview

■ Radionuclide Tables

Database Schema

IDC-5.1.1Rev5 October 2002 441 IDC DOCUMENTATION User Guides

Chapter 5: Radionuclide Entity Relationships

OVERVIEW

This chapter contains entity-relationship diagrams that illustrate the relationships between database tables for the radionuclide database schema. The table name is always shown at the top of the table. Keys are shown below the table name. The primary key of a table is indicated with a filled symbol. Optional foreign keys are unshaded. Keys consisting of multiple columns are shown with a key symbol next to the first column of the key and the remaining columns are listed beneath with no symbols. All column names are shown below the key section in the diagrams. Not all foreign keys are identified.

RADIONUCLIDE TABLES

Figures 26 through 37 illustrate the relationships among the various tables in the radionuclide database. In the following figures, a table is linked by either a single or double arrow. A single arrow indicates that a single record exists in the relationship to the table from where the record came. A double arrow indicates that one or more records exist in the relationship. For example, a single gards_sample_status record exists for each gards_sample_data record. However, multiple gards_nucl_ided records are related to each gards_sample_data record.

Database Schema

442 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 5:

Radionuclide Entity Relationships ▼

gards_poc gards_stations gards_sample_data

pocid station_id sample_id pocid station_id pocid detector_id email_address station_id first_name station_code site_det_code last_name country_code sample_id telephone type station_id address description detector_id additional_info lat input_file_name lon sample_type elevation data_type date_begin geometry date_end spectral_qualifier status transmit_dtg pocid collect_start collect_stop acquisition_start acquisition_stop acquisition_real_sec gards_detectors acquisition_live_sec quantity detector_id

detector_id detector_code description lat lon type channels rated_efficiency rated resolution ecal_range_max date_begin date_end status

FIGURE 26.RADIONUCLIDE EQUIPMENT

Database Schema

IDC-5.1.1Rev5 October 2002 443 IDC DOCUMENTATION Chapter 5: User Guides

▼ Radionuclide Entity Relationships

gards_soh_header gards_data_log gards_rlr

soh_id dlid rlr_id station_id station_id station_id detector_id detector_id station_id soh_id data_type rlr_id station_id date_received station_id detector_id dtg detector_id dtg_begin msg_id ref_id dtg_end status collect_start transmit_dtg file_size collect_stop auth arrival_date rms_id test_date dlid transmit_date filename

gards_alerts

station_id dtg

station_id station_code dtg alert_type alert_text

gards_soh_num_data gards_soh_char_data station_id gards_soh_sensor_data station_id detector_id detector_id param_code station_id param_code dtg_begin detector_id dtg_begin dtg_end sensor_type dtg_begin station_id station_id station_id detector_id detector_id detector_id param sensor_type param_code param_code sensor_name value value value dtg_begin dtg_begin dtg_begin dtg_end dtg_end dtg_end

FIGURE 27.RAW SENSOR DATA

Database Schema

444 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 5:

Radionuclide Entity Relationships ▼

gards_histogram gards_sample_data gards_spectrum

sample_id sample_id sample_id station_id sample_id detector_id sample_id filename sample_type g_channels site_det_code filename b_channels sample_id channels g_energy_span station_id energy_span b_energy_span detector_id input_file_name sample_type data_type gards_sample_aux geometry gards_sample_description spectral_qualifier sample_id transmit_dtg sample_id msg_id collect_start collect_stop sample_id sample_id acquisition_start description sample_ref_id acquisition_stop measurement_id acquisition_real_sec bkgd_measurement_id acquisition_live_sec sample_height quantity calibration_dtg msg_id archive_bottle_id gas_bkgd_measurement_id gards_data_log xe_collect_yield xe_collect_yield_err dlid xe_volume station_id xe_volume_err sample_diameter station_id data_type date_received dtg msg_id status file_size auth rms_id dlid

FIGURE 28.RAW PULSE HEIGHT DATA

Database Schema

IDC-5.1.1Rev5 October 2002 445 IDC DOCUMENTATION Chapter 5: User Guides

▼ Radionuclide Entity Relationships

gards_energy_pairs gards_sample_data gards_resolution_pairs

sample_id sample_id sample_id cal_energy station_id res_energy sample_id detector_id sample_id

sample_id site_det_code sample_id cal_energy sample_id res_energy channel station_id resolution cal_error detector_id res_error input_file_name sample_type data_type gards_efficiency_pairs geometry spectral_qualifier sample_id transmit_dtg effic_energy collect_start sample_id collect_stop acquisition_start sample_id acquisition_stop effic_energy acquisition_real_sec efficiency acquisition_live_sec effic_error quantity

FIGURE 29.RAW PARTICULATE CALIBRATION DATA

Database Schema

446 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 5:

Radionuclide Entity Relationships ▼

gards_energy_pairs gards_sample_data gards_resolution_pairs

sample_id sample_id sample_id cal_energy station_id res_energy sample_id detector_id sample_id

sample_id site_det_code sample_id cal_energy sample_id res_energy channel station_id resolution cal_error detector_id res_error input_file_name sample_type data_type gards_b_energy_pairs gards_sample_ratios geometry spectral_qualifier sample_id sample_id transmit_dtg cal_energy ratio_id collect_start sample_id sample_id collect_stop acquisition_start sample_id sample_id acquisition_stop decay_mode ratio_id acquisition_real_sec cal_energy upper_roi_number acquisition_live_sec cal_error lower_roi_number quantity channel count_ratio count_ratio_err gards_b_resolution_pairs

sample_id gards_roi_limits res_energy sample_id sample_id roi sample_id sample_id resolution roi res_energy res_error sample_id roi upper_roi_number lower_roi_number gards_bg_efficiency_pairs count_ratio count_ratio_err sample_id roi sample_id roi

sample_id bg_efficiency bg_effic_error roi

FIGURE 30.RAW NOBLE GAS DATA

Database Schema

IDC-5.1.1Rev5 October 2002 447 IDC DOCUMENTATION Chapter 5: User Guides

▼ Radionuclide Entity Relationships

gards_energy_cal gards_sample_data gards_resolution_cal

sample_id sample_id sample_id station_id sample_id detector_id sample_id coeff1 coeff1 coeff2 site_det_code coeff2 coeff3 sample_id coeff3 coeff4 station_id coeff4 coeff5 detector_id coeff5 coeff6 input_file_name coeff6 coeff7 sample_type coeff7 coeff8 data_type coeff8 energy_units geometry cnv_factor spectral_qualifier ape transmit_dtg det collect_start mse collect_stop tstat acquisition_start score acquisition_stop acquisition_real_sec acquisition_live_sec quantity gards_efficiency_cal

sample_id

sample_id degree efftype coeff1 coeff2 coeff3 coeff4 coeff5 coeff6 coeff7 coeff8

FIGURE 31.CALCULATED PARTICULATE CALIBRATION DATA

Database Schema

448 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 5:

Radionuclide Entity Relationships ▼

gards_nucl_ided gards_sample_data gards_peaks

sample_id sample_id sample_id name station_id peak_id sample_id detector_id sample_id station_id detector_id site_det_code sample_id name sample_id peak_id station_id centroid sample_id detector_id centroid_err station_id input_file_name energy detector_id sample_type energy_err nuclide_id data_type left_chan name geometry width type spectral_qualifier back_count halflife transmit_dtg back_uncer ave_activ collect_start fwhm ave_activ_err collect_stop fwhm_err activ_key acquisition_start area activ_key_err acquisition_stop area_err mda acquisition_real_sec original_area mda_err acquisition_live_sec original_uncer nid_flag quantity counts_sec activ_decay counts_sec_err activ_decay_err efficiency comp_confid gards_nucl_lines_ided eff_error report_mda back_channel pd_mod_flag sample_id ided name fitted energy multiplet lc gards_sample_cat sample_id station_id peak_sig detector_id peak_tol sample_id pss name name name sample_id sample_id station_id name detector_id method_id name category energy upper_bound energy_err lower_bound abundance central_value abundance_err delta peak activity activity hold activity_err effic effic_err mda key_flag nuclide_id

FIGURE 32.CALCULATED PARTICULATE DETECTION AND CHARACTERIZATION DATA

Database Schema

IDC-5.1.1Rev5 October 2002 449 IDC DOCUMENTATION Chapter 5: User Guides

▼ Radionuclide Entity Relationships

gards_sample_proc_params gards_sample_data gards_sample_status

sample_id sample_id sample_id station_id sample_id detector_id sample_id do_back entry_date back_data_type site_det_code cnf_begin_date back_sample_id sample_id cnf_end_date nuclide_lib station_id review_date energy_tol detector_id review_time mda_level input_file_name analyst nid_confid sample_type status squant_err data_type category buildtype geometry auto_category peak_sense spectral_qualifier peak_start transmit_dtg peak_end collect_start fwhm_mult_width collect_stop left_fwhm_lim acquisition_start right_fwhm_lim acquisition_stop back_chan acquisition_real_sec back_type acquisition_live_sec fit_singlets quantity crit_level fix_fwhm area_reject mdc_width gards_sample_update_params lc_abscissa do_pd_calc sample_id mrp_sample_id

sample_id mrp_used mrp_sample_id gainshift Zeroshift area_lim use_weight use_mult f_linear bootstrap min_lookup rer_intercept rer_slope ecr_slope do_reru

FIGURE 33.PARTICULATE PARAMETER AND STATUS DATA

Database Schema

450 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 5:

Radionuclide Entity Relationships ▼

gards_roi_channels gards_sample_data gards_roi_concs

sample_id sample_id sample_id roi station_id roi sample_id detector_id sample_id roi roi site_det_code sample_id sample_id sample_id roi station_id roi b_chan_start detector_id activity b_chan_stop input_file_name activ_err g_chan_start sample_type mda g_chan_stop data_type nid_flag geometry report_mda spectral_qualifier transmit_dtg gards_roi_counts collect_start collect_stop sample_id acquisition_start roi acquisition_stop sample_id acquisition_real_sec roi acquisition_live_sec quantity sample_id roi gross gross_err compton compton_err interference interference_err memory memory_err detector_back detector_back_err net net_err lc

FIGURE 34.CALCULATED NOBLE GAS DETECTION DATA

Database Schema

IDC-5.1.1Rev5 October 2002 451 IDC DOCUMENTATION Chapter 5: User Guides

▼ Radionuclide Entity Relationships

gards_sample_xe_proc_params gards_sample_data gards_sample_status

sample_id sample_id sample_id roi station_id sample_id detector_id sample_id roi entry_date site_det_code cnf_begin_date sample_id sample_id cnf_end_date roi station_id review_date lc_abscissa detector_id review_time beta_ecr_order input_file_name analyst gamma_ecr_order sample_type status compton data_type category det_back_used geometry auto_category gas_back_used spectral_qualifier transmit_dtg collect_start collect_stop acquisition_start acquisition_stop acquisition_real_sec acquisition_live_sec quantity

FIGURE 35.NOBLE GAS PARAMETER AND STATUS DATA

Database Schema

452 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 5:

Radionuclide Entity Relationships ▼

gards_sample_data gards_comments

sample_id comment_id station_id sample_id detector_id sample_id peak_id site_det_code sample_id gards_comments_defs sample_id nucl_name station_id comment_type comment_type detector_id input_file_name sample_id comment_type sample_type peak_id comment_text data_type nucl_name geometry comment_id spectral_qualifier analyst transmit_dtg dtg collect_start comment_type collect_stop acquisition_start acquisition_stop gards_user_comments acquisition_real_sec acquisition_live_sec comment_id quantity sample_id

sample_id comment_id comment_text

FIGURE 36.ANALYST COMMENT DATA

Database Schema

IDC-5.1.1Rev5 October 2002 453 IDC DOCUMENTATION Chapter 5: User Guides

▼ Radionuclide Entity Relationships

gards_roles gards_roles_permissions gards_permissions

role_id role_id permission_id permission_id role_id role_id permission_id role_name permission_id permission_name db_name db_name role_id permission_id gards_users_roles gards_sample_data

user_id gards_dist_sample_queue sample_id role_id station_id user_id sample_id detector_id role_id user_id role_id site_det_code user_id sample_id role_id sample_id station_id default_role used_id detector_id role_id input_file_name sample_type gards_users data_type gards_station_assignments geometry user_id spectral_qualifier station_id transmit_dtg user_id user_id collect_start user_name collect_stop assignable station_id acquisition_start user_id acquisition_stop acquisition_real_sec gards_stations acquisition_live_sec quantity station_id pocid

station_id station_code country_code type description lat lon elevation date_begin date_end status pocid

FIGURE 37.MULTIPLE ANALYST REVIEW DATA

Database Schema

454 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

Chapter 6: Radionuclide Table Descriptions

This chapter describes the tables that comprise the IDC radionuclide schema and defines the physical structure of each table as it exists within the ORACLE data dictionary. Brief descriptions of the columns are provided for convenience. “Radionuclide Column Descriptions” on page 579 contains detailed descriptions of the columns.

Database Schema

IDC-5.1.1Rev5 October 2002 455 IDC DOCUMENTATION User Guides

Chapter 6: Radionuclide Table Descriptions

GARDS_ALERTS

The gards_alerts table contains data describing all radionuclide alert messages received.

TABLE 139:GARDS_ALERTS

Column Storage Type Description

1 station_id number station identifier

2 station_code char(5) station code

3 dtg date date alert received

4 alert_type varchar2(20) category of alert (current alert types are ALERT_TEMP, ALERT_FLOW, ALERT_SYSTEM, and ALERT_UPS)

5 alert_text varchar2(512) alert message text

Keys: Primary: station_id/dtg Foreign: station_id (gards_stations) station_id/dtg (gards_data_log)1

1. The related gards_data_log entry can be found by matching the station_id and dtg between the two tables where gards_data_log.data_type = ‘ALERT’.

Database Schema

456 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_AUTO_SAMPLE_CAT

The gards_auto_sample_cat table contains original categorization values from automatic processing.

TABLE 140:GARDS_AUTO_SAMPLE_CAT

Column Storage Type Description

1 sample_id number sample identifier

2 name varchar2(8) nuclide name

3 method_id number method identifier

4 category number categorization level

5 upper_bound number upper limit of the amount of a nuclide that can be acceptably found

6 lower_bound number lower limit of the amount of a nuclide that can be acceptably found

7 central_value number current estimate of the level of the random process

8 delta number value of a variable used in bounds estimation (EWMA algorithm)

9 activity number relates to gards_nucl_ided.activ_key

10 hold number flag that hold categorization bounds fixed and does not update values (0 = proceed, 1 = wait)

Keys: Primary: name Foreign: name (gards_nucl_lib)

Database Schema

IDC-5.1.1Rev5 October 2002 457 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_AUX_LIB

The gards_aux_lib table provides additional radionuclide information that is useful to the analyst and used in the parent-progeny calculation.

TABLE 141:GARDS_AUX_LIB

Column Storage Type Description

1 name varchar2(8) nuclide name

2 branch_ratio number percentage of decays to given decay path

3 chain_id number decay chain index

4 chain_pos number position in decay chain

5 halflife_act varchar2(23) actual half-life

6 halflife_act_err varchar2(23) uncertainty of halflife_act

Keys: Primary: name Foreign: name (gards_nucl_lib)

Database Schema

458 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_AUX_LINES_LIB

The gards_aux_lines_lib table provides additional radionuclide line information that is useful to the analyst and is used in the parent-progeny calculation.

TABLE 142:GARDS_AUX_LINES_LIB

Column Storage Type Description

1 name varchar2(8) nuclide name

2 energy number line energy (keV)

3 abundance_act number intensity of nuclear transition

4 abundance_act_err number uncertainty of abundance_act

5 line_comment varchar2(500) description of line properties

6 line_type varchar2(8) type of radiation causing the line

7 reference varchar2(8) reference for line properties

Keys: Primary: name/energy Foreign: name/energy (gards_nucl_lines_lib)

Database Schema

IDC-5.1.1Rev5 October 2002 459 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_B_ENERGY_PAIRS

The gards_b_energy_pairs table contains the energy calibration pairs information associated with the beta axis of the spectrum used in rms_xanalyze. The values in the gards_b_energy_pairs and the gards_b_energy_pairs_orig tables are identical.

TABLE 143:GARDS_B_ENERGY_PAIRS

Column Storage Type Description

1 sample_id number sample identifier

2 decay_mode char(1) type of decay; B = beta particle, C = conversion electron

3 cal_energy number calibration energy (keV)

4 cal_error number uncertainty of channel

5 channel number peak centroid channel

Keys: Primary: sample_id/cal_energy Foreign: sample_id (gards_sample_data)

Database Schema

460 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_B_ENERGY_PAIRS_ORIG

The gards_b_energy_pairs_orig table contains the original energy calibration pairs information associated with the beta axis of the spectrum as specified in the PHD file. The values in the gards_b_energy_pairs and the gards_b_energy_pairs_orig tables are identical. This table is not used by the rms_xanalyze process.

TABLE 144:GARDS_B_ENERGY_PAIRS_ORIG

Column Storage Type Description

1 sample_id number sample identifier

2 decay_mode char(1) type of decay; B = beta particle, C = conversion electron

3 cal_energy number calibration energy (keV)

4 cal_error number uncertainty of channel

5 channel number peak centroid channel

Keys: Primary: sample_id/cal_energy Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 461 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_B_RESOLUTION_PAIRS

The gards_b_resolution_pairs table contains the resolution calibration pairs information associated with the beta axis of the spectrum. This table is not used by the rms_xanalyze process. The values in the gards_b_resolution_pairs and the gards_b_resolution_pairs_orig tables are identical.

TABLE 145:GARDS_B_RESOLUTION_PAIRS

Storage Column Description Type

1 sample_id number sample identifier

2 resolution number detector resolution (keV)

3 res_energy number resolution energy (keV)

4 res_error number uncertainty of resolution (keV)

Keys: Primary: sample_id/res_energy Foreign: sample_id (gards_sample_data)

Database Schema

462 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_B_RESOLUTION_PAIRS_ORIG

The gards_b_resolution_pairs_orig table contains the original resolution calibration pairs information associated with the beta axis of the spectrum as specified in the PHD file. This table is not used by the rms_xanalyze process. The values in the gards_b_resolution_pairs and the gards_b_resolution_pairs_orig tables are identical.

TABLE 146:GARDS_B_RESOLUTION_PAIRS_ORIG

Column Storage Type Description

1 sample_id number sample identifier

2 resolution number detector resolution (keV)

3 res_energy number resolution energy (keV)

4 res_error number uncertainty of resolution (keV)

Keys: Primary: sample_id/res_energy Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 463 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_BG_EFFICIENCY_PAIRS

The gards_bg_efficiency_pairs table contains the detection efficiency associated with a beta-gamma coincidence event as specified in the PHD file.

TABLE 147:GARDS_BG_EFFICIENCY_PAIRS

Column Storage Type Description

1 sample_id number sample identifier

2 bg_efficiency number detection efficiency of β-γ coincidence event

3 bg_effic_error number uncertainty of bg_efficiency

4 roi number ROI identifier

Keys: Primary: sample_id/roi Foreign: sample_id (gards_sample_data) roi (gards_roi_lib)

Database Schema

464 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_BG_ENERGY_CAL

The gards_bg_energy_cal table contains the energy-to-channel ratios of a sample.

TABLE 148:GARDS_BG_ENERGY_CAL

Column Storage Type Description

1 sample_id number sample identifier

2 beta_coeff1 number zero shift of the beta ECR equation

3 beta_coeff2 number linear coefficient of the beta ECR equation

4 beta_coeff3 number quadratic coefficient of the beta ECR equation

5 gamma_coeff1 number zero shift of the gamma ECR equation

6 gamma_coeff2 number linear coefficient of the gamma ECR equation

7 gamma_coeff3 number quadratic coefficient of the gamma ECR equation

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 465 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_CAT_CRITERIA_TESTS

The gards_cat_criteria_tests table contains a list of all category criteria tests. The column active_flag is set to 0 if the test should not be run. A trigger updates the moddate column when any modification is made to another column.

TABLE 149:GARDS_CAT_CRITERIA_TESTS

Column Storage Type Description

1 test_id number unique identitifier

2 test_code varchar2(24) unique test code identifier string

3 test_name varchar2(48) test name label for display

4 lower_limit number lower limit bound of the test

5 upper_limit number upper limit bound of the test

6 units varchar2(16) unit values for the test bounds

7 active_flag number 0 if test is inactive

8 moddate date modification date

Keys: Primary: test_id

Database Schema

466 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_CAT_TEMPLATE

The gards_cat_template table contains categorization initialization information for typical nuclides.

TABLE 150:GARDS_CAT_TEMPLATE

Column Storage Type Description

1 station_id number station identifier

2 name varchar2(8) nuclide name

3 method_id number method identifier

4 method_type number type of categorization analysis to use

5 init_begin_date date start date for initialization data

6 init_end_date date end date for initialization data

7 begin_date date date initialization began

8 end_date date date initialization ended

9 analyst varchar2(30) name of analyst initializing nuclide categorization

10 detector_id number detector identifier

11 comment_text varchar2(256) comment on the filter

12 upper_bound number upper limit of the amount of a nuclide that can be acceptably found

13 lower_bound number lower limit of the amount of a nuclide that can be acceptably found

14 central_value number current estimate of the level of the random process

15 delta number value of a variable used in bounds estimation (EWMA algorithm)

16 abscissa number acceptable number of standard deviations away from the central_value where the amount of a nuclide may be found (RDC algorithm)

Database Schema

IDC-5.1.1Rev5 October 2002 467 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

TABLE 150:GARDS_CAT_TEMPLATE (CONTINUED)

Column Storage Type Description

17 num_samples number number of samples used to collect the average and define the standard deviation (RDC algorithm)

18 alpha number value of a variable used in bounds estimation (EWMA algorithm)

19 gamma number value of a variable used in bounds estimation (EWMA algorithm)

20 tstat number value of a variable used in bounds estimation (EWMA algorithm)

21 xform number code for transform function applied to measurement data

Keys: Primary: station_id/detector_id

Database Schema

468 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_CODES

The gards_codes table contains codes for items used throughout radionuclide monitoring system.

TABLE 151:GARDS_CODES

Column Storage Type Description

1 type varchar2(15) category of code

2 code char(5) code symbol

3 description varchar2(40) code explanation

Keys: Primary: type/code

Database Schema

IDC-5.1.1Rev5 October 2002 469 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_COMMENTS

The gards_comments table contains automated analysis and interactive review comments related to peaks in the gards_peaks table and nuclides in the gards_nucl_ided table.

TABLE 152:GARDS_COMMENTS

Column Storage Type Description

1 sample_id number sample identifier

2 peak_id number peak identifier

3 nucl_name varchar2(8) nuclide name referenced by comment

4 comment_id number unique comment identifier

5 analyst varchar2(30) individual (or process) entering comment

6 dtg date comment entry date

7 comment_type number comment code

Keys: Primary: comment_id Foreign: sample_id (gards_sample_data) sample_id/peak_id (gards_peaks) sample_id/nucl_name (gards_nucl_ided) comment_type (gards_comments_defs)

Database Schema

470 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_COMMENTS_DEFS

The gards_comments_defs table contains predefined comments for automated analysis and interactive review.

TABLE 153:GARDS_COMMENTS_DEFS

Column Storage Type Description

1 comment_type number predefined comment code

2 comment_text varchar2(256) predefined comment text

Keys: Primary: comment_type

Database Schema

IDC-5.1.1Rev5 October 2002 471 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_CSC_MODCOEFF_LIB

The gards_csc_modcoeff_lib table contains the cascade summing ratios used by rms_analyze.

TABLE 154:GARDS_CSC_MODCOEFF_LIB

Column Storage Type Description

1 detector_id number detector identifier

2 name varchar2(9) nuclide name

3 name_d varchar2(9) daughter nuclide name

4 energy number energy of nuclide line

5 abundance number abundance of line (%)

6 app_abundance number apparent abundance

7 app_abundance_err number absolute error in apparent abundance

8 csc_ratio number CSC correction factor

9 csc_ratio_err number error in CSC

10 moddate number row modification date

Keys: Primary: detector_id, name, energy Foreign: detector_id (gards_detectors) name (gards_nucl_lib)

Database Schema

472 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_DATA_LOG

The gards_data_log table contains data describing all radionuclide data messages received.

TABLE 155:GARDS_DATA_LOG

Column Storage Type Description

1 station_id number station identifier

2 data_type varchar2(10) type of data message (current choices include: ALERT, MET, SOH, SPHD-B, SPHD-C, SPHD-D, SPHD-F, SPHD-P, SPHD-Q, SPHD-G)

3 date_received date data message arrival date (GMT)

4 dtg date date included within data message (GMT)

5 msg_id number message identifier sent in the mail header of the message

6 status char(1) status of data msg_id processing; U = sequencing has not been run on message, P = sequence process has checked message

7 file_size number data message size (KB)

8 auth number authentication status of associated message; 1 = authenticated, 0 = not authenticated

9 rms_id number internal identifier for message; either the sample_id for PHDs, the rlr_id for RLRs, or the soh_id for SOHs

10 dlid number data log identifier

Keys: Primary: dlid Foreign: station_id (gards_stations)

Database Schema

IDC-5.1.1Rev5 October 2002 473 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_DBROLE_OWNER

The gards_dbrole_owner table contains information used by the MAR tool to determine the database user that owns the RMS roles.

TABLE 156:GARDS_DBROLE_OWNER

Column Storage Type Description

1 owner varchar(12) name of database user who owns the RMS roles for the MAR tool

Database Schema

474 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_DETECTORS

The gards_detectors table contains detector overviews and characteristics.

TABLE 157:GARDS_DETECTORS

Column Storage Type Description

1 detector_id number unique detector identifier

2 detector_code varchar2(9) detector identification code

3 description varchar2(80) detector description

4 lat number latitude (degrees)

5 lon number longitude (degrees)

6 type varchar2(6) detector type

7 channels number number of channels

8 rated_efficiency number rated efficiency of detector

9 rated_resolution number rated resolution of detector

10 ecal_range_max number maximum detector calibration energy (keV)

11 date_begin date detector initialization date

12 date_end date detector decommissioning date

13 status varchar2(2) status of detector, if Y then data from this detector are automatically processed if N then they are not automatically processed

Keys: Primary: detector_id

Database Schema

IDC-5.1.1Rev5 October 2002 475 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_DIST_SAMPLE_QUEUE

The gards_dist_sample_queue table contains a list of samples and the user or role to which they are assigned.

TABLE 158:GARDS_DIST_SAMPLE_QUEUE

Column Storage Type Description

1 sample_id number sample identifier

2 user_id number user identifier

3 role_id number role identifier

Keys: Primary: sample_id Foreign: user_id (gards_users) rule_id (gards_roles)

Database Schema

476 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_EFFICIENCY_CAL

The gards_efficiency_cal table contains the efficiency calibration equation that is computed for each spectra.

TABLE 159:GARDS_EFFICIENCY_CAL

Column Storage Type Description

1 sample_id number sample identifier

2 degree number degree of efficiency equation

3 efftype char(8) efficiency type

4 coeff1 number first order calibration coefficient

5 coeff2 number second order calibration coefficient

6 coeff3 number third order calibration coefficient

7 coeff4 number fourth order calibration coefficient

8 coeff5 number fifth order calibration coefficient

9 coeff6 number sixth order calibration coefficient

10 coeff7 number seventh order calibration coefficient

11 coeff8 number eighth order calibration coefficient

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 477 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_EFFICIENCY_PAIRS

The gards_efficiency_pairs table contains efficiency calibration pairs as specified in the PHD file.

TABLE 160:GARDS_EFFICIENCY_PAIRS

Column Storage Type Description

1 sample_id number sample identifier

2 effic_energy number efficiency energy (keV)

3 efficiency number efficiency

4 effic_error number uncertainty of efficiency

Keys: Primary: sample_id/effic_energy Foreign: sample_id (gards_sample_data)

Database Schema

478 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_ENERGY_CAL

The gards_energy_cal table contains efficiency calibration coefficients associated with spectra. The equation is calculated during energy calibration update.

TABLE 161:GARDS_ENERGY_CAL

Column Storage Type Description

1 sample_id number sample identifier

2 coeff1 number first order calibration coefficient

3 coeff2 number second order calibration coefficient

4 coeff3 number third order calibration coefficient

5 coeff4 number fourth order calibration coefficient

6 coeff5 number fifth order calibration coefficient

7 coeff6 number sixth order calibration coefficient

8 coeff7 number seventh order calibration coefficient

9 coeff8 number eighth order calibration coefficient

10 energy_units char(3) energy units

11 cnv_factor number conversion to keV

12 ape number average prediction error, a measure of the average confidence interval for the calculated energy vs. channel regression (ECR) over the range of 100 keV

13 det number determinant of the weighted design matrix, a measure of the spread of fitted data points and the error in the fitted points

Database Schema

IDC-5.1.1Rev5 October 2002 479 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

TABLE 161:GARDS_ENERGY_CAL (CONTINUED)

Column Storage Type Description

14 mse number mean-squared error of the fit, a measure of how large the residuals are

15 tstat number percentage point of the t-statistic for Type I error with a probability set to 99%

16 score number score used when comparing this ECR to other ECRs, a measure of both the ape and determinant

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

480 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_ENERGY_CAL_ORIG

The gards_energy_cal_orig table contains original energy calibration equation information associated with samples (calculated using energy pair data).

TABLE 162:GARDS_ENERGY_CAL_ORIG

Column Storage Type Description

1 sample_id number sample identifier

2 coeff1 number first order calibration coefficient

3 coeff2 number second order calibration coefficient

4 coeff3 number third order calibration coefficient

5 coeff4 number fourth order calibration coefficient

6 coeff5 number fifth order calibration coefficient

7 coeff6 number sixth order calibration coefficient

8 coeff7 number seventh order calibration coefficient

9 coeff8 number eighth order calibration coefficient

10 energy_units char(3) energy units

11 cnv_factor number conversion to keV

12 ape number average prediction error, a measure of the average confidence interval for the calculated energy vs. channel regression (ECR) over the range of 100 keV

13 det number determinant of the weighted design matrix, a measure of the spread of fitted data points and the error in the fitted points

Database Schema

IDC-5.1.1Rev5 October 2002 481 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

TABLE 162:GARDS_ENERGY_CAL_ORIG (CONTINUED)

Column Storage Type Description

14 mse number mean-squared error of the fit, a measure of how large the residuals are

15 tstat number percentage point of the t-statistic for Type I error with a probability set to 99%

16 score number score used when comparing this ECR to other ECRs, a measure of both the ape and determinant

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

482 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_ENERGY_PAIRS

The gards_energy_pairs table contains energy calibration pairs information associated with the gamma axis of the spectrum.

TABLE 163:GARDS_ENERGY_PAIRS

Column Storage Type Description

1 sample_id number sample identifier

2 cal_energy number calibration energy (keV)

3 channel number peak centroid channel

4 cal_error number uncertainty of channel

Keys: Primary: sample_id/cal_energy Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 483 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_ENERGY_PAIRS_ORIG

The gards_energy_pairs_orig table contains energy calibration pairs information associated with the gamma axis of the spectrum. These values are as specified in the PHD file.

TABLE 164:GARDS_ENERGY_PAIRS_ORIG

Column Storage Type Description

1 sample_id number sample identifier

2 cal_energy number calibration energy (keV)

3 channel number peak centroid channel

4 cal_error number uncertainty of channel

Keys: Primary: sample_id/cal_energy Foreign: sample_id (gards_sample_data)

Database Schema

484 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_ENVIRONMENT

The gards_environment table contains atmospheric conditions and related sample information. This table is applicable to PHDs sent in IMS1.0 format or earlier. It does not apply to messages in IMS2.0 format or later.

TABLE 165:GARDS_ENVIRONMENT

Column Storage Type Description

1 sample_id number sample identifier

2 flow_rate number flow rate through filter (m3/h)

3 pressure number outside pressure (mbar)

4 temperature number outside temperature (°C)

5 end_env_time date end date of environment data

6 end_env_time_sec number end time of environment data (seconds)

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 485 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_FLAGS

The gards_flags table contains the name and thresholds for each of the tests run during rms_DBflags.

TABLE 166:GARDS_FLAGS

Column Storage Type Description

1 flag_id number unique identifier for an event screening test

2 name varchar2(32) name of the event screening test

3 threshold number value against which the results in the test column are compared

4 units varchar2(16) units of the event screening test

5 test varchar2(8) calculated result of the test; this value is compared to the threshold value (examples are <, = , >, >=)

Keys: Primary: flag_id

Database Schema

486 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_FPE

The gards_fpe table contains one record for each sample associated with a fission product event.

TABLE 167:GARDS_FPE

Column Storage Type Description

1 fpid number unique fission product identifier

2 revid number revision number

3 dtg date data product generation date

4 sample_id number sample identifier

Keys: Primary: fpid/sample_id Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 487 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_HISTOGRAM

The gards_histogram table contains information regarding the three dimensional beta- gamma coincidence sample data.

TABLE 168:GARDS_HISTOGRAM

Column Storage Type Description

1 sample_id number sample identifier

2 filename varchar2(256) name of file containing histogram data

3 g_channels number number of gamma channels in histogram

4 b_channels number number of beta channels in histogram

5 g_energy_span number gamma energy span of detector calibration (keV)

6 b_energy_span number beta energy span of detector calibration (keV)

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

488 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_INTERVAL

The gards_interval table contains data used to update RMS data workflow.

TABLE 169:GARDS_INTERVAL

Column Storage Type Description

1 class varchar2(16) station name

2 name varchar2(16) detector/system identifier

3 start_time float start time of interval

4 end_time float end time of interval

5 state varchar2(16) specific activity of detector/system

6 moddate date modification date

7 lddate date load date

Keys: Primary: class/name/start_time/end_time

Database Schema

IDC-5.1.1Rev5 October 2002 489 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_MDAS2REPORT

The gards_mdas2report table contains the list of nuclides which have their minimum detectable activities reported in radionuclide reports.

TABLE 170:GARDS_MDAS2REPORT

Column Storage Type Description

1 name varchar2(8) nuclide name

2 type varchar2(16) nuclide type: ACTIVATION, COSMIC, FISSION(G), FISSION(P), or NATURAL

3 mda_min number minimum bound for minimum detectable activity (MDA) range (µBq/m3)

4 mda_max number maximum bound for MDA range (µBq/ m3)

5 sample_type varchar2(2) sample type (P for particulate or G for gas)

6 dtg_begin date start date of bound applicability

7 dtg_end date end date of bound applicability

Keys: Primary: name/sample_type

Database Schema

490 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_MET_DATA

The gards_met_data table contains station local meteorological data.

TABLE 171:GARDS_MET_DATA

Column Storage Type Description

1 station_id number station identifier

2 ave_humidity number average humidity (percent relative humidity)

3 ave_out_temp number average outside temperature (°C)

4 ave_pressure number average pressure (mbar)

5 ave_wind_dir number average wind direction (degrees from North)

6 ave_wind_speed number average wind speed (km/h)

7 total_rainfall number total rainfall (mm)

8 start_time date start time of measurement

9 end_time date end time of measurement

Keys: Primary: station_id/start_time Foreign: station_id (gards_stations)

Database Schema

IDC-5.1.1Rev5 October 2002 491 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_NOTIFY

The gards_notify table contains contact information for specific events. When the event occurs a message is automatically sent to the email_addr of the specified recipient.

TABLE 172:GARDS_NOTIFY

Column Storage Type Description

1 event varchar2(10) type of occurrence (choices are: ALERT, FISS_FOUND, NIC_SIG34, NIC_SIG5, QC_ERROR, QC_WARNING, RADOPSCAL, RMS_ADMIN)

2 email_addr varchar2(80) recipient email addresses

3 description varchar2(80) general description of occurrence

4 dtg_begin date notification initialization date

5 dtg_end date notification termination date

6 pocid number not used

Keys: Primary: event/email_addr/dtg_end

Database Schema

492 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_NUCL2QUANTIFY

The gards_nucl2quantify table contains natural radionuclides quantified in radionuclide related reports.

TABLE 173:GARDS_NUCL2QUANTIFY

Column Storage Type Description

1 name varchar2(8) nuclide name

2 dtg_begin date start of reporting period

3 dtg_end date end of reporting period

Keys: Primary: name/dtg_begin

Database Schema

IDC-5.1.1Rev5 October 2002 493 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_NUCL_IDED

The gards_nucl_ided table contains information regarding nuclides identified during interactive review.

TABLE 174:GARDS_NUCL_IDED

Column Storage Type Description

1 sample_id number sample identifier

2 station_id number station identifier

3 detector_id number detector identifier

4 nuclide_id number nuclide identifier

5 name varchar2(8) nuclide name Canberra Parameter: CAM_T_NCLNAME

6 type varchar2(16) nuclide type (choices are: ACTIVATION, COS- MIC, FISSION(G), FISSION(P), or NATU- RAL) Canberra param: CAM_T_NCLSBHDR

7 halflife varchar2(23) half-life in seconds (S), hours (H), days (D), or years (Y) Canberra Parameter: CAM_T_NCLHLFLIFE

8 ave_activ number average activity for nuclide (µBq/m3) Canberra Parameter: CAM_T_NCLWTMEAN

9 ave_activ_err number uncertainty in average activity (µBq/m3) Canberra Parameter: CAM_T_NCLWTMERR

10 activ_key number key-line activity (µBq/m3) Canberra Parameter: CAM_G_NCLACTVTY

11 activ_key_err number uncertainty of key-line activity (µBq/m3) Canberra Parameter: CAM_G_NCLEER

12 mda number minimum detectable activity (µBq/m3) Canberra Parameter: CAM_G_NCLMDA

Database Schema

494 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

TABLE 174:GARDS_NUCL_IDED (CONTINUED)

Column Storage Type Description

13 mda_err number minimum detectable activity uncertainty (µBq/m3) Canberra Parameter: CAM_G_NCLMDAERR

14 nid_flag number nuclide identification indicator (0 = nuclide was not identified by automated analysis; 1 = nuclide was identified by automated analysis; -1 = nuclide was identified initially by automated analysis but later rejected because the concentration was < 0.0; 2 = nuclide was identified by automated analysis but was removed by the analyst through the Inspectra) Canberra Parameter: CAM_G_NCLFIDENT

15 activ_decay number activity decay factor Canberra Parameter: CAM_G_NCLDECAY

16 activ_decay_err number uncertainty in activity decay Canberra Parameter: CAM_F_NCLDECAYERR

17 comp_confid number computed confidence index Canberra Parameter: CAM_F_NCLCONFID

18 report_mda number indicator of whether MDA is to be reported

19 pd_mod_flag number flag that indicates if a nuclide’s activity was modified by the parent/daughter calculation; 1 = the activity was modified, 0 = no modification

20 csc_ratio number multiplier used by analysis to update active_key and mda

21 csc_ratio_err number uncertainty in csc_ratio

22 csc_mod_flag number flag that indicates if cascade summing modified a nuclide: 1 = nuclide was modified, 0 = nuclide was not modified

Database Schema

IDC-5.1.1Rev5 October 2002 495 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

Keys: Primary: sample_id/name Foreign: sample_id (gards_sample_data) station_id (gards_stations) detector_id (gards_detectors) name (gards_nucl_lib)

Database Schema

496 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_NUCL_IDED_ORIG

The gards_nucl_ided_orig table contains information regarding nuclides identified during automated analysis.

TABLE 175:GARDS_NUCL_IDED_ORIG

Column Storage Type Description

1 sample_id number sample identifier

2 station_id number station identifier

3 detector_id number detector identifier

4 nuclide_id number identification code of associated nuclide

5 name varchar2(8) nuclide name Canberra Parameter: CAM_T_NCLNAME

6 type varchar2(16) nuclide type (choices are: ACTIVATION, COS- MIC, FISSION(G), FISSION(P), or NATU- RAL) Canberra Parameter: CAM_T_NCLSBHDR

7 halflife varchar2(23) half-life in seconds (S), hours (H), minutes (M), or years (Y) Canberra Parameter: CAM_T_NCLHLFLIFE

8 ave_activ number average activity for nuclide (µBq/m3) Canberra Parameter: CAM_T_NCLWTMEAN

9 ave_activ_err number uncertainty in average activity (µBq/m3) Canberra Parameter: CAM_T_NUCLWTMERR

10 activ_key number activity of key-line (µBq/m3) Canberra Parameter: CAM_G_NCLACTVTY

11 activ_key_err number uncertainty of key-line activity (µBq/m3) Canberra Parameter: CAM_G_NCLERR

12 mda number minimum detectable activity (µBq/m3) Canberra Parameter: CAM_G_NCLMDA

Database Schema

IDC-5.1.1Rev5 October 2002 497 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

TABLE 175:GARDS_NUCL_IDED_ORIG (CONTINUED)

Column Storage Type Description

13 mda_err number minimum detectable activity error (µBq/m3) Canberra Parameter: CAM_G_NCLMDAERR

15 activ_decay number activity decay factor Canberra Parameter: CAM_G_NCLDECAY

16 activ_decay_err number uncertainty of activity decay Canberra Parameter: CAM_F_NCLDECAYERR

17 comp_confid number computed confidence index Canberra Parameter: CAM_F_NCLCONFID

18 report_mda number indicator of whether MDA is to be reported

19 pd_mod_flag number flag that indicates if a nuclide’s activity was modified by the parent/daughter calculation; 1 = the activity was modified, 0 = no modification

Keys: Primary: sample_id/name Foreign: sample_id (gards_sample_data) station_id (gards_stations) detector_id (gards_detectors) name (gards_nucl_lib)

Database Schema

498 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_NUCL_LIB

The gards_nucl_lib table contains nuclide library information used by the Inspectra when displaying nuclide data for particulate stations.

TABLE 176:GARDS_NUCL_LIB

Column Storage Type Description

1 nuclide_id number nuclide identifier

2 name varchar2(8) nuclide name

3 type varchar2(16) nuclide type (ACTIVATION, COSMIC, FISSION(G), FISSION(P), or NATURAL)

4 halflife_sec number half-life in seconds

5 halflife varchar2(23) half-life

6 halflife_err varchar2(23) uncertainty of half-life

7 num_lines number number of nuclide lines in library

Keys: Primary: name

Database Schema

IDC-5.1.1Rev5 October 2002 499 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_NUCL_LINES_IDED

The gards_nucl_lines_ided table contains auxiliary information regarding lines identified by interactive review.

TABLE 177:GARDS_NUCL_LINES_IDED

Column Storage Type Description

1 sample_id number sample identifier

2 station_id number station identifier

3 detector_id number detector identifier

4 name varchar2(8) nuclide name Canberra Parameter: CAM_T_NCLNAME

5 energy number line energy (keV) Canberra Parameter: CAM_F_NLENERGY

6 energy_err number uncertainty in line energy Canberra Parameter: CAM_F_NLENGERR

7 abundance number abundance of line (percent) Canberra Parameter: CAM_F_NLABUN

8 abundance_err number uncertainty of abundance (percent) Canberra Parameter: CAM_F_NLABUNERR

9 peak number peak identifier Canberra Parameter: CAM_L_NLPEAK

10 activity number line activity (µBq/m3) Canberra Parameter: CAM_G_NLACTVTY

11 activ_err number percent uncertainty of line activity Canberra Parameter: CAM_G_NLERR

12 effic number efficiency at energy Canberra Parameter: CAM_F_NLEFFICIENCY

13 effic_err number uncertainty of efficiency Canberra Parameter: CAM_F_NLEFFERR

Database Schema

500 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

TABLE 177:GARDS_NUCL_LINES_IDED (CONTINUED)

Column Storage Type Description

14 mda number minimum detectable activity (µBq/m3) Canberra Parameter: CAM_F_NLMDA

15 key_flag number key line indicator Canberra Parameter: CAM_V_NLF_KEYLINE

16 nuclide_id number nuclide number associated with line number Canberra Parameter: CAM_L_NLNUCL

17 csc_ratio number multiplier used by analysis to update activ_key and mda 18 csc_ratio_err number uncertainty in csc_ratio

19 csc_mod_flag number flag that indicates if cascade summing modified a nuclide: 1 = nuclide was modified, 0 = nuclide was not modified.

Keys: Primary: sample_id/name/energy Foreign: sample_id (gards_sample_data) station_id (gards_stations) detector_id (gards_detectors) name (gards_nucl_lib)

Database Schema

IDC-5.1.1Rev5 October 2002 501 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_NUCL_LINES_IDED_ORIG

The gards_nucl_lines_ided_orig table contains information regarding lines identified during automated analysis.

TABLE 178:GARDS_NUCL_LINES_IDED_ORIG

Column Storage Type Description

1 sample_id number sample identifier

2 station_id number station identifier

3 detector_id number detector identifier

4 name varchar2(8) nuclide name Canberra Parameter: CAM_T_NCLNAME

5 energy number line energy (keV) Canberra Parameter: CAM_F_NLENERGY

6 energy_err number uncertainty of line energy Canberra Parameter: CAM_F_NLENGERR

7 abundance number abundance of line (percent) Canberra Parameter: CAM_F_NLABUN

8 abundance_err number uncertainty of abundance (percent) Canberra Parameter: CAM_F_NLABUNERR

9 peak number peak associated with line Canberra Parameter: CAM_L_NLPEAK

10 activity number line activity (µBq/m3) Canberra Parameter: CAM_G_NLACTVTY

11 activ_err number percent uncertainty of line activity Canberra Parameter: CAM_G_NLERR

12 effic number efficiency at energy Canberra Parameter: CAM_F_NLEFFICIENCY

13 effic_err number uncertainty of efficiency Canberra Parameter: CAM_F_NLEFFERR

Database Schema

502 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

TABLE 178:GARDS_NUCL_LINES_IDED_ORIG (CONTINUED)

Column Storage Type Description

14 mda number minimum detectable activity (µBq/m3) Canberra Parameter: CAM_F_NLMDA

15 key_flag number key line indicator Canberra Parameter: CAM_V_NLF_KEYLINE

16 nuclide_id number nuclide number associated with line number Canberra Parameter: CAM_L_NLNUCL

Keys: Primary: sample_id/name/energy Foreign: sample_id (gards_sample_data), station_id (gards_stations), detector_id (gards_detectors) name (gards_nucl_lib)

Database Schema

IDC-5.1.1Rev5 October 2002 503 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_NUCL_LINES_LIB

The gards_nucl_lines_lib table contains library information used in particulate nuclide identification process.

TABLE 179:GARDS_NUCL_LINES_LIB

Column Storage Type Description

1 name varchar2(8) nuclide name

2 energy number line energy (keV) Canberra Parameter: CAM_F_NLENERGY

3 energy_err number uncertainty of line energy Canberra Parameter: CAM_F_NLENGERR

4 abundance number abundance of line (percent) Canberra Parameter: CAM_F_NLABUN

5 abundance_err number uncertainty of abundance (percent) Canberra Parameter: CAM_F_NLABUNERR

6 key_flag number key line indicator Canberra Parameter: CAM_V_NLF_KEYLINE

7 nuclide_id number nuclide number associated with line number Canberra Parameter: CAM_L_NLNUCL

Keys: Primary: name/energy Foreign: name (gards_nucl_lib)

Database Schema

504 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_PEAKS

The gards_peaks table contains information regarding peaks identified during interactive review.

TABLE 180:GARDS_PEAKS

Column Storage Type Description

1 sample_id number sample identifier

2 peak_id number peak identifier

3 centroid number peak centroid (channels) Canberra Parameter: CAM_F_PSCENTRD

4 centroid_err number uncertainty of peak centroid Canberra Parameter: CAM_F_PSDCENTRD

5 energy number energy at peak centroid (keV) Canberra Parameter: CAM_F_PSENERGY

6 energy_err number uncertainty of energy (keV) Canberra Parameter: CAM_F_PSDENERGY

7 left_chan number left channel of peak Canberra Parameter: CAM_L_PSLEFT

8 width number width of peak (channels) Canberra Parameter: CAM_L_PSWIDTH

9 back_count number continuum background counts Canberra Parameter: CAM_F_PSBACKGND

10 back_uncer number uncertainty in continuum background counts Canberra Parameter: CAM_F_PSBACK

11 fwhm number full width at half maximum Canberra Parameter: CAM_F_PSFWHM

12 fwhm_err number uncertainty of full width at half maximum Canberra Parameter: CAM_F_PSDFWHM

13 area number peak area (counts) Canberra Parameter: CAM_F_PSAREA

Database Schema

IDC-5.1.1Rev5 October 2002 505 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

TABLE 180:GARDS_PEAKS (CONTINUED)

Column Storage Type Description

14 area_err number uncertainty of peak area (counts) Canberra Parameter: CAM_F_PSDAREA

15 original_area number original peak area (counts) Canberra Parameter: CAM_F_PSORIGAREA

16 original_uncer number uncertainty of original peak area (counts) Canberra Parameter: CAM_F_PSORIGERR

17 count_sec number count rate (counts/second) Canberra Parameter: CAM_F_PSCTSS

18 count_sec_err number uncertainty of count rate (percent) Canberra Parameter: CAM_F_PSCERR

19 efficiency number efficiency Canberra Parameter: CAM_F_PSEFF

20 eff_error number uncertainty of efficiency Canberra Parameter: CAM_F_PSEFERR

21 back_channel number number of average background channels Canberra Parameter: CAM_F_PSBKCHAN

22 ided number peak identification indicator; 1 = peak was associated with a nuclide by the automated analysis, 0 = peak was not associated with a nuclide by the automated analysis (not updated by the ROI interface) Canberra Parameter: CAM_L_PSPKNOWN

23 fitted number peak fit indicator Canberra Parameter: CAM_L_PSPPFIT

24 multiplet number multiplet peak indicator Canberra Parameter: CAM_L_PSPMULT

25 lc number critical level for the peak (counts)

Database Schema

506 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

TABLE 180:GARDS_PEAKS (CONTINUED)

Column Storage Type Description

26 peak_sig number peak significance, peak area divided by Lc

27 peak_tol number per peak energy tolerance; approximates the energy tolerance at a given peak

28 pss number peak search significance parameter Canberra parameter: CAM_F_PSSIGNIF

Keys: Primary: sample_id/peak_id Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 507 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_PEAKS_ORIG

The gards_peaks_orig table contains information regarding peaks identified during automated analysis.

TABLE 181:GARDS_PEAKS_ORIG

Column Storage Type Description

1 sample_id number sample identifier

2 peak_id number peak identifier

3 centroid number peak centroid (channels) Canberra Parameter: CAM_F_PSCENTRD

4 centroid_err number uncertainty of peak centroid (channels) Canberra Parameter: CAM_F_PSDCENTRD

5 energy number energy at peak centroid (keV) Canberra Parameter: CAM_F_PSENERGY

6 energy_err number uncertainty of energy (keV) Canberra Parameter: CAM_F_PSDENERGY

7 left_chan number left channel of peak Canberra Parameter: CAM_L_PSLEFT

8 width number width of peak (channels) Canberra Parameter: CAM_L_PSWIDTH

9 back_count number continuum background counts Canberra Parameter: CAM_F_PSBACKGND

10 back_uncer number uncertainty of continuum background counts Canberra Parameter: CAM_F_PSDBACK

11 fwhm number full width at half maximum Canberra Parameter: CAM_F_PSFWHM

12 fwhm_err number uncertainty of full width at half maximum Canberra Parameter: CAM_PSDFWHM

13 area number peak area (counts) Canberra Parameter: CAM_F_PSAREA

Database Schema

508 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

TABLE 181:GARDS_PEAKS_ORIG (CONTINUED)

Column Storage Type Description

14 area_err number uncertainty of peak area (counts) Canberra Parameter: CAM_F_PSDAREA

15 original_area number original peak area (counts) Canberra Parameter: CAM_PSORIGAREA

16 original_uncer number uncertainty of original peak area (counts) Canberra Parameter: CAM_PSORIGERR

17 count_sec number count rate (counts/second) Canberra Parameter: CAM_F_PSCTSS

18 count_sec_err number uncertainty of count rate (percent) Canberra Parameter: CAM_PSCERR

19 efficiency number efficiency Canberra Parameter: CAM_F_PSEFF

20 eff_error number uncertainty of efficiency Canberra Parameter: CAM_F_PSEFERR

21 back_channel number number of average background channels Canberra Parameter: CAM_L_PSBKCHAN

22 ided number peak identification indicator; 1 = peak was associated with a nuclide by the automated analysis, 0 = peak was not associated with a nuclide by the automated analysis (not updated by the ROI interface) Canberra Parameter: CAM_L_PSPKNOWN

23 fitted number peak fit indicator Canberra Parameter: CAM_F_PSPPFIT

24 multiplet number multiplet peak indicator Canberra Parameter: CAM_PSPMULT

25 lc number critical level for the peak (counts)

Database Schema

IDC-5.1.1Rev5 October 2002 509 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

TABLE 181:GARDS_PEAKS_ORIG (CONTINUED)

Column Storage Type Description

26 peak_sig number peak significance, peak area divided by Lc

27 peak_tol number per peak energy tolerance; approximates the energy tolerance at a given peak

28 pss number peak search significance parameter Canberra parameter: CAM_F_PSSIGNIF

Keys: Primary: sample_id/peak_id Foreign: sample_id (gards_sample_data)

Database Schema

510 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_PERMISSIONS

The gards_permissions table contains a list of permissions that can be manipulated by the MAR tool.

TABLE 182:GARDS_PERMISSIONS

Column Storage Type Description

1 permission_id number unique permission identifier

2 permission_name varchar2(30) string name of a permission

3 db_name varchar2(35) name of corresponding role in the database

Keys: Primary: permission_id

Database Schema

IDC-5.1.1Rev5 October 2002 511 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_POC

The gards_poc table contains information for radionuclide monitoring system points of contact (POC).

TABLE 183:GARDS_POC

Column Storage Type Description

1 pocid number unique point of contact identifier

2 email_address varchar2(50) email address of point of contact

3 first_name varchar2(20) first name of point of contact

4 last_name varchar2(50) last name of point of contact

5 telephone varchar2(20) telephone number of point of contact

6 address varchar2(500) address of point of contact

7 additional_info varchar2(500) additional information for point of contact

Keys: Primary: pocid

Database Schema

512 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_PROC_PARAMS_TEMPLATE

The gards_proc_params_template table is a template data record that contains parameters used by Automatic Analysis process software for peak search and nuclide identification. These parameters are used unless overridden at the command line.

TABLE 184:GARDS_PROC_PARAMS_TEMPLATE

Column Storage Type Description

1 station_id number station identifier Canberra Parameter: CAM_L_SSPI5

2 detector_id number detector identifier (relates to gards_detectors.detector_id) Canberra Parameter: CAM_L_SSPI6

3 sample_type varchar2(2) type of sample Canberra Parameter: CAM_T_SSPRSTR1

4 data_type char(1) spectral data type

5 spectral_qualifier varchar2(5) indicator of full or preliminary sample

6 begin_date date initialization date of parameters

7 end_date date termination date of parameters

8 do_back number background subtraction indicator Canberra Parameter: CAM_L_PRNOBACKCOR

9 back_data_type char(1) blank (B), or detector background (D) spectral type

10 nuclide_lib varchar2(96) nuclide library to be used during analysis

11 mda_level number MDA confidence factor (percent) Canberra Parameter: CAM_F_MDACONFID

12 nid_confid number NID confidence factor (percent) Canberra Parameter: CAM_F_CONFID

13 squant_err number error in sample quantity Canberra Parameter: CAM_F_SQUANTERR

Database Schema

IDC-5.1.1Rev5 October 2002 513 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

TABLE 184:GARDS_PROC_PARAMS_TEMPLATE (CONTINUED)

Column Storage Type Description

14 buildtype varchar2(8) flag for Canberra: activity (NONE), or concentration (BUILD), calculations

15 peak_sense number peak search sensitivity Canberra Parameter: CAM_F_SENSITIVITY

16 peak_start number peak search start (keV) Canberra Parameter: CAM_L_PEAKSTART

17 peak_end number peak search end (keV) Canberra Parameter: CAM_L_PEAKEND

18 fwhm_mult_width number number of FWHMs to search to determine multiplets Canberra Parameter: CAM_F_PRFWHMPKMULT

19 left_fwhm_lim number left ROI FWHM limit Canberra Parameter: CAM_F_PRFWHMPKLEFT

20 right_fwhm_lim number right ROI FWHM limit Canberra Parameter: CAM_F_PRFWHMPKRIGHT

21 back_chan number number of continuous channels Canberra Parameter: CAM_L_PRNBKCHN

22 back_type varchar2(6) background type Canberra Parameter: CAM_T_ROIPSBTYP

23 fit_singlets number fit singlets flag, Canberra Parameter: CAM_L_PRFIT

24 crit_level number critical level test indicator, Canberra Parameter: CAM_L_CRITLEVEL

25 fix_fwhm number fixed FWHM during peak search flag Canberra Parameter: CAM_L_PRFIXFWHM

Database Schema

514 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

TABLE 184:GARDS_PROC_PARAMS_TEMPLATE (CONTINUED)

Column Storage Type Description

26 area_reject number indicatior of whether or not to reject peaks with zero area indicator Canberra Parameter: CAM_L_PRREJECTPEAKS

27 mdc_width number baseline width used for MDA calculation Canberra param: CAM_F_VPWIDTH

28 lc_abscissa number abscissas of the normal distribution corresponding to a confidence level; a value of 1.645 corresponds to a 95% confidence interval for the peak critical level

29 do_pd_calc number flag indicates if the parent/daughter calculations should be run; 1 = run calculations, 0 = do not run calculations

30 do_csc number flag to turn off cascade summing correction

Keys: Primary: station_id/detector_id/data_typ/spectral_qualifier Foreign: station_id (gards_stations), detector_id (gards_detectors)

Database Schema

IDC-5.1.1Rev5 October 2002 515 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_PROCESSING_ERRORS

The gards_processing_errors table contains sample information, if applicable, and message information for RMS messages that have failed processing.

TABLE 185:GARDS_PROCESSING_ERRORS

Column Storage Type Description

1 rms_id number sequence number of associated data type (e.g., RMSSOH, SAMPLEPHD, etc.). If SAMPLEPHD, the sequence refers to a sample_id; if RMSSOH, the RMS ID refers to an soh_id.

2 sample_ref_id varchar2(32) sample reference identification

3 msg_id number message identifier

4 filename varchar2(512) import message filename

5 station_code varchar2(5) station code parsed from import message

6 detector_code varchar2(9) detector code parsed from import message

7 data_type varchar2(12) data type parsed from message header (e.g., RMSSOH, MET, SAMPLEPHD, etc.)

8 error_text varchar2(2048) text associated with the error

9 entry_date date date and time of error entry

Keys: Primary: none

Database Schema

516 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_QAT_CONFIG

The gards_qat_config table contains q_time and t_time used by rms_QAT_auto; there is only one record in the database.

TABLE 186:GARDS_QAT_CONFIG

Column Storage Type Description

1 t_time number number of minutes after gards_sample_status.entry_date that rms_QAT_auto waits before releasing a sample

2 min_t_time number minimum allowable value for t_time

3 max_t_time number maximum allowable value for t_time

4 q_time number number of minutes after gards_sample_status.review_date that rms_QAT_auto waits before releasing a sample

5 poll_time number number of minutes rms_QAT sleeps between each database poll

6 moddate date date of last modification

Keys: Primary: none

Database Schema

IDC-5.1.1Rev5 October 2002 517 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_QAT_NOTIFY

The gards_qat_notify table contains comments created by rms_QAT.

TABLE 187:GARDS_QAT_NOTIFY

Column Storage Type Description

1 sample_id number foriegn key

2 comment_text varchar2(2048) text of the comment

3 comment_type number foriegn key to gards_comments_defs

4 nucl_name varchar2(8) nuclide name referenced by comment

5 energy number energy (keV) referenced by comment

6 dtg date date comment was entered

7 author varchar2(30) user name of Radionuclide Officer

8 recipient_list varchar2(128) comma-separated list of users to whom the notification was sent

9 moddate date date of last modification

Keys: Primary: sample_id

Database Schema

518 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_QAT_QUERY_FILTER

The gards_qat_query_filter table contains each user’s default query in rms_QAT.

TABLE 188:GARDS_QAT_QUERY_FILTER

Column Storage Type Description

1 user_id number foreign key to gards_users

2 min_sample_id number foreign key

3 max_sample_id number foreign key

4 sample_status varchar2(128) comma-separated list of sample status values

5 station_list varchar2(1024) comma-separated list of stations

6 include_stations number flag to include or exclude stations

7 category_list varchar2(32) comma-separated list of categories

8 use_review_cat number flag for reviewed or auto categorization.

Keys: Primary: user_id Foreign: min_sample_id, max_sample_id

Database Schema

IDC-5.1.1Rev5 October 2002 519 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_QCHISTORY

The gards_qchistory table contains output messages from quality control tests for each sample.

TABLE 189:GARDS_QCHISTORY

Column Storage Type Description

1 station_id number station identifier

2 detector_id number detector identifier

3 sample_id number sample identifier

4 state varchar2(128) text results of quality control hypothesis tests

5 lddate date date of quality control processing

Keys: Primary: sample_id/state Foreign: sample_id (gards_sample_data), station_id (gards_stations), detector_id (gards_detectors)

Database Schema

520 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_QCPARAMS

The gards_qcparams table contains parameters for quality control processes.

TABLE 190:GARDS_QCPARAMS

Column Storage Type Description

1 detector_id number detector identifier

2 gainchange number gain first difference tolerance

3 sdmult number location test standard deviation multiplier

4 width_adj number peak width standard deviation inflation factor

5 area_adj number peak area standard deviation inflation factor

6 etol number energy tolerance used to match peaks with energies (keV)

Keys: Primary: detector_id Foreign: detector_id (gards_detectors)

Database Schema

IDC-5.1.1Rev5 October 2002 521 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_QCTARGETS

The gards_qctargets table contains detector-specific target values for the quality control width and area tests.

TABLE 191:GARDS_QCTARGETS

Column Storage Type Description

1 station_id number station identifier

2 detector_id number detector identifier

3 dtg date decay correction reference date

4 name varchar2(8) nuclide name

5 energy number nuclide line energy (keV)

6 muwidth number target width for each nuclide line energy (keV)

7 muarea number target area for each nuclide line energy (counts)

Keys: Primary: name/detector_id/station_id/energy Foreign station_id (gards_stations) detector_id (gards_detectors)

Database Schema

522 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_QUERY_RESULTS

The gards_query_results table contains output of a user-initiated query from the event screening tool. This table is purged at the end of the request.

TABLE 192:GARDS_QUERY_RESULTS

Column Storage Type Description

1 rqst_id number unique query identifier

2 rqst_string varchar2(100) output of the user query

Keys: Primary: rqst_id

Database Schema

IDC-5.1.1Rev5 October 2002 523 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_READ_SAMPLE_STATUS

In both the AUTO and MAN schemas, the gards_read_sample_status table is a synonym for the MAN schema table gards_sample_status. This synonym allows rms_categorize to read gards_sample_status regardless of how it was started.

TABLE 193:GARDS_READ_SAMPLE_STATUS

Column Storage Type Description

1 sample_id number sample identifier

2 entry_date date date sample was entered into database

3 cnf_begin_date date date when last analysis began

4 cnf_end_date date date when last analysis ended

5 review_date date date sample was last reviewed

6 review_time number amount of time to review sample (minutes) (no longer automatically updated)

7 analyst varchar2(30) name of analyst who reviewed sample

8 status char(1) current processing status of sample. Some possible values are: A- analyzed, P- processed, R- reviewed, U- unprocessed, V- viewed

9 category number sample categorization level after interactive analysis

10 auto_category number sample categorization level after automated analysis

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

524 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_RECEIPT_LOG

The gards_receipt_log table is used by the gards_receipts utility.

TABLE 194:GARDS_RECEIPT_LOG

Column Storage Type Description

1 pocid number poc identifier

2 subid number not used

3 prodid number not used

4 type varchar2(5) type of data

5 dtg date date sent

6 kb_sent number size of data (KB)

Keys: Primary: prodid Foreign: pocid (gards_poc)

Database Schema

IDC-5.1.1Rev5 October 2002 525 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_REFLINE_MASTER

The gards_refline_master table contains resolution calibration pairs information associated with spectral pulse height data (PHD).

TABLE 195:GARDS_REFLINE_MASTER

Column Storage Type Description

1 refpeak_energy number known reference energy for a nuclide

2 data_type char(1) indicator of the type of sample. An uncontaminated crushed filter (‘B’), calibration background (‘C’), detector background (‘D’), quality control (‘Q’), or an actual sample (‘S’)

3 spectral_qualifier varchar2(5) time for which the sample was exposed, ‘FULL’ or ‘PREL’ (preliminary)

4 calibration_type varchar2(3) type of calibration, ‘CAL’, ‘MIX’, or ‘---’

Keys: Primary: rfpeak_energy/data_type/spectral_qualifier

Database Schema

526 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_RELEVANT_NUCLIDES

The gards_relevant_nuclides table contains the list of nuclides determined to be relevant during the identification of radionuclide events. This table includes the categorization list for particulate samples (CLPS) and the relevant radioxenon isotopes.

TABLE 196:GARDS_RELEVANT_NUCLIDES

Column Storage Type Description

1 name varchar2(8) name of the nuclide

2 type varchar2(16) nuclide type (choices are: ACTIVATION, COSMIC, FISSION(G), FISSION(P), or NATURAL)

3 sample_type char(1) sample type (P, G, or B)

Keys: Primary: name/sample_type

Database Schema

IDC-5.1.1Rev5 October 2002 527 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_RESOLUTION_CAL

The gards_resolution_cal table contains resolution calibration coefficients calculated during analysis.

TABLE 197:GARDS_RESOLUTION_CAL

Column Storage Type Description

1 sample_id number sample identifier

2 coeff1 number first order calibration coefficient

3 coeff2 number second order calibration coefficient

4 coeff3 number third order calibration coefficient

5 coeff4 number fourth order calibration coefficient

6 coeff5 number fifth order calibration coefficient

7 coeff6 number sixth order calibration coefficient

8 coeff7 number seventh order calibration coefficient

9 coeff8 number eighth order calibration coefficient

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

528 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_RESOLUTION_CAL_ORIG

The gards_resolution_cal_orig table contains the original resolution calibration coefficients calculated during analysis.

TABLE 198:GARDS_RESOLUTION_CAL_ORIG

Column Storage Type Description

1 sample_id number sample identifier

2 coeff1 number first order calibration coefficient

3 coeff2 number second order calibration coefficient

4 coeff3 number third order calibration coefficient

5 coeff4 number fourth order calibration coefficient

6 coeff5 number fifth order calibration coefficient

7 coeff6 number sixth order calibration coefficient

8 coeff7 number seventh order calibration coefficient

9 coeff8 number eighth order calibration coefficient

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 529 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_RESOLUTION_PAIRS

The gards_resolution_pairs table contains resolution calibration pairs information associated with spectral PHD.

TABLE 199:GARDS_RESOLUTION_PAIRS

Column Storage Type Description

1 sample_id number sample identifier

2 res_energy number resolution energy (keV)

3 resolution number resolution (keV)

4 res_error number error in resolution (keV)

Keys: Primary: sample_id/res_energy Foreign: sample_id (gards_sample_data)

Database Schema

530 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_RESOLUTION_PAIRS_ORIG

The gards_resolution_pairs_orig table contains the original resolution calibration pairs information associated with spectral PHD.

TABLE 200:GARDS_RESOLUTION_PAIRS_ORIG

Column Storage Type Description

1 sample_id number sample identifier

2 res_energy number resolution energy (keV)

3 resolution number resolution (keV)

4 res_error number error in resolution (keV)

Keys: Primary: sample_id/res_energy Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 531 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_RLR

The gards_rlr table contains all data related to a Radionuclide Laboratory Report (RLR) message.

TABLE 201:GARDS_RLR

Column Storage Type Description

1 rlr_id number unique RLR identifier

2 station_id number station identifier

3 detector_id number detector identifier

4 ref_id varchar2(32) sample reference identification

5 collect_start number sample collection start date

6 collect_stop date sample collection stop date

7 arrival_date date sample arrival date

8 test_date date test completion date at lab

9 transmit_date date transmit date

10 filename varchar2(256) name of file containing the RLR

Keys: Primary: rlr_id Foreign: rlr_id (gards_data_log.rmsid) station_id (gards_stations) detector_id (gards_detectors)

Database Schema

532 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_ROI_CHANNELS

The gards_roi_channels table contains the ROI boundaries in channel units that are calculated in rms_xanalyze.

TABLE 202:GARDS_ROI_CHANNELS

Column Storage Type Description

1 sample_id number sample identifier

2 roi number ROI identifier

3 b_chan_start number beta boundary start channel

4 b_chan_stop number beta boundary stop channel

5 g_chan_start number gamma boundary start channel

6 g_chan_stop number gamma boundary stop channel

Keys: Primary: sample_id/roi Foreign: sample_id (gards_sample_data) roi (gards_roi_lib)

Database Schema

IDC-5.1.1Rev5 October 2002 533 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_ROI_CONCS

The gards_roi_concs table contains information regarding the concentration of each identified nuclide that is calculated in rms_xanalyze.

TABLE 203:GARDS_ROI_CONCS

Column Storage Type Description

1 sample_id number sample identifier

2 roi number ROI identifier

3 activity number activity per unit volume air (µBq/m3)

4 activ_err number uncertainty of activity (µBq/m3)

5 mda number minimum detectable activity (µBq/m3)

6 nid_flag number nuclide identification indicator (0 = nuclide was not identified by automated analysis; 1 = nuclide was identified by automated analysis; -1 = nuclide was identified initially by automated analysis but later rejected because the concentration was <0.0; 2 = nuclide was identified by automated analysis but was removed by the analyst through the Inspectra)

7 report_mda number indicator of whether MDA is to be reported

Keys: Primary: sample_id/roi Foreign: sample_id (gards_sample_data) roi (gards_roi_lib)

Database Schema

534 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_ROI_COUNTS

The gards_roi_counts table contains information regarding the counts that are calculated in rms_xanalyze for each ROI.

TABLE 204:GARDS_ROI_COUNTS

Column Storage Type Description

1 sample_id number sample identifier

2 roi number ROI identifier

3 gross number counts in ROI before processing

4 gross_err number uncertainty of gross (counts)

5 compton number compton continuum background counts

6 compton_err number uncertainty of compton (counts)

7 interference number counts from interference nuclides

8 interference_err number uncertainty of interference (counts)

9 memory number gas background counts

10 memory_err number uncertainty of memory (counts)

11 detector_back number detector background counts

12 detector_back_err number uncertainty of detector_back (counts)

13 net number counts in ROI after processing

14 net_err number uncertainty of net (counts)

15 lc number critical level (counts)

Keys: Primary: sample_id/roi Foreign: sample_id (gards_sample_data) roi (gards_roi_lib)

Database Schema

IDC-5.1.1Rev5 October 2002 535 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_ROI_LIB

The gards_roi_lib table relates each ROI to a specific nuclide. The table also contains nuclide properties used in nuclide quantification.

TABLE 205:GARDS_ROI_LIB

Column Storage Type Description

1 roi number unique ROI identifier

2 name varchar2(8) nuclide associated with ROI

3 halflife varchar2(23) half-life of the nuclide

4 halflife_err varchar2(23) uncertainty of halflife

5 halflife_sec number numerical half-life in seconds

6 abundance number intensity of β-γ coincidence event

7 abundance_err number uncertainty of abundance

Keys: Primary: roi Foreign: sample_id (gards_sample_data) roi (gards_roi_lib)

Database Schema

536 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_ROI_LIMITS

The gards_roi_limits table contains the ROI boundaries in energy units as specified in the PHD file.

TABLE 206:GARDS_ROI_LIMITS

Column Storage Type Description

1 sample_id number sample identifier

2 roi number ROI identifier

3 b_energy_start number beta boundary start energy (keV)

4 b_energy_stop number beta boundary stop energy (keV)

5 g_energy_start number gamma boundary start energy (keV)

6 g_energy_stop number gamma boundary stop energy (keV)

Keys: Primary: sample_id/roi Foreign: sample_id (gards_sample_data) roi (gards_roi_lib)

Database Schema

IDC-5.1.1Rev5 October 2002 537 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_ROLES

The gards_roles table contains the list of roles that can be manipulated by the MAR tools.

TABLE 207:GARDS_ROLES

Column Storage Type Description

1 role_id number unique role identifier

2 role_name varchar2(30) string name of a role

3 db_name varchar2(35) name of corresponding database role

Keys: Primary: role_id

Database Schema

538 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_ROLES_PERMISSIONS

The gards_roles_permissions table contains a mapping of which permissions are assigned to which roles.

TABLE 208:GARDS_ROLES_PERMISSIONS

Column Storage Type Description

1 role_id number role identifier

2 permission_id number permission identifier

Keys: Primary: role_id/permission_id Foreign: role_id (gards_roles) permission_id (gards_permissions)

Database Schema

IDC-5.1.1Rev5 October 2002 539 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_SAMPLE_AUX

The gards_sample_aux table contains auxiliary information related to raw sample data.

TABLE 209:GARDS_SAMPLE_AUX

Column Storage Type Description

1 sample_id number sample identifier

2 sample_ref_id varchar2(32) sample reference identification

3 measurement_id varchar2(31) unique detection identifier

4 bkgd_measurement_id varchar2(31) unique background identifier corresponding to detection identifier

5 sample_height number height of sample (cm)

6 calibration_dtg date date of most recent calibration at detector site

7 msg_id number message identifier

8 archive_bottle_id char(2) unique identifier of the archive bottle in which the sample is stored

9 gas_bkgd_measurement_id varchar2(31) unique measurement id (MID) of the gas background acquisition associated with the sample

10 xe_collect_yield number Xe collection yield of the system (volume of stable Xe on detector/volume of stable Xe collected on first trap)

11 xe_collect_yield_err number uncertainty of xe_collect_yield

12 xe_volume number volume of stable Xe in gas cell counter (cm3)

13 xe_volume_err number uncertainty of xe_volume in cm3

14 sample_diameter number diameter of gas chamber (cm)

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data) message_id (gards_data_log)

Database Schema

540 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_SAMPLE_CAT

The gards_sample_cat table contains the most recent categorization values from either automatic or manual processing.

TABLE 210:GARDS_SAMPLE_CAT

Column Storage Type Description

1 sample_id number sample identifier

2 name varchar2(8) nuclide name

3 method_id number method identifier

4 category number categorization level

5 upper_bound number upper limit of the amount of a nuclide that can be acceptably found

6 lower_bound number lower limit of the amount of a nuclide that can be acceptably found

7 central_value number current estimate of the level of the random process

8 delta number value of a variable used in bounds estimation (EWMA algorithm)

9 activity number relates to gards_nucl_ided.activ_key

10 hold number flag that hold categorization bounds fixed and does not update values (0 = proceed, 1 = wait)

Keys: Primary: sample_id, name Foreign: name (gards_nucl_lib)

Database Schema

IDC-5.1.1Rev5 October 2002 541 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_SAMPLE_CERT

The gards_sample_cert table contains overview information regarding certificate data found in pulse height data messages.

TABLE 211:GARDS_SAMPLE_CERT

Column Storage Type Description

1 sample_id number sample identifier

2 quantity number quantity associated with certificate

3 assay_date date date sample was assayed

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

542 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_SAMPLE_CERT_LINES

The gards_sample_cert_lines table contains nuclide information regarding certificate data found in pulse height data messages.

TABLE 212:GARDS_SAMPLE_CERT_LINES

Column Storage Type Description

1 sample_id number sample identifier (relates to gards_sample_data.sample_id)

2 nucl_name varchar2(8) nuclide name

3 halflife varchar2(23) half-life of nuclide

4 energy number energy of nuclide

5 activity number activity of nuclide at time of assay

6 error number percent error in activity

7 abundance number percent abundance

8 b_abundance number intensity of beta particle or conversion electron (particles/decay)

9 b_energy number energy of conversion electron or maximum energy of beta particle (keV)

10 decay_mode char(1) type of decay; B = beta particle, C = conversion electron

Keys: Primary: sample_id/nucl_name/energy Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 543 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_SAMPLE_DATA

The gards_sample_data table contains header data from PHD messages.

TABLE 213:GARDS_SAMPLE_DATA

Column Storage Type Description

1 site_det_code char(15) station code concatenated with detector code

2 sample_id number unique sample identifier

3 station_id number station identifier

4 detector_id number detector identifier

5 input_file_name varchar2(256) input data filename

6 sample_type char(1) sample type (P, G, or B)

7 data_type char(1) type of sample; an uncontaminated crushed blank filter (B), calibration background (C), detector background (D), quality control (Q), or an actual sample (S).

8 geometry varchar2(17) sample geometry Canberra param: CAM_T_GEOMETRY

9 spectral_qualifier varchar2(5) time for which the sample was exposed: FULL or PREL (preliminary)

10 transmit_dtg date transmit date time group

11 collect_start date collection start time Canberra param: CAM_X_SDEPOSIT

12 collect_stop date collection stop time Canberra param: CAM_X_STIME

13 acquisition_start date acquisition start time

14 acquisition_stop date acquisition stop time

15 acquisition_real_sec number difference between acquisition stop and acquisition start (seconds)

16 acquisition_live_sec number active detection time (seconds)

17 quantity number air volume sampled (m3)

Database Schema

544 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

Keys: Primary: sample_id Foreign: detector_id (gards_detectors) station_id (gards_stations) sample_id (gards_data_log.rms_id)

Database Schema

IDC-5.1.1Rev5 October 2002 545 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_SAMPLE_DESCRIPTION

The gards_sample_description table contains description and comment text as specified in a PHD file.

TABLE 214:GARDS_SAMPLE_DESCRIPTION

Column Storage Type Description

1 sample_id number sample identifier

2 description varchar2(512) comments

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

546 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_SAMPLE_FLAGS

The gards_sample_flags table contains the results of the rms_DBflags analysis for each sample.

TABLE 215:GARDS_SAMPLE_FLAGS

Column Storage Type Description

1 sample_id number sample identifier

2 flag_id number flag identifier

3 result number indicator of whether or not the test passed

4 value number threshold value used for the test

Keys: Primary: sample_id/flag_id Foreign: sample_id (gards_sample_data) flag_id (gards_flags)

Database Schema

IDC-5.1.1Rev5 October 2002 547 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_SAMPLE_PROC_PARAMS

The gards_sample_proc_params table contains specific processing parameters to be used for a particular spectral analysis; the table contains a combination of values from gards_proc_params_template and values entered at the command line.

TABLE 216:GARDS_SAMPLE_PROC_PARAMS

Column Storage Type Description

1 sample_id number sample identifier

2 do_back number background subtraction indicator Canberra Parameter: CAM_L_PRNOBACKCOR

3 back_data_type char(1) data type used for background subtraction; blank (B), or detector background (D)

4 back_sample_id number sample identifier for sample used in background subtraction

5 nuclide_lib varchar2(96) nuclide library to be used during analysis Canberra Parameter: CAM_T_EXPLIB

6 energy_tol number tolerence for nuclide identification Canberra Parameter: CAM_F_TOLERANCE

7 mda_level number MDA confidence factor Canberra Parameter: CAM_F_MDACONFID

8 nid_confid number NID confidence factor Canberra Parameter: CAM_F_CONFID

9 squant_err number uncertainty of sample quantity (m3) Canberra param: CAM_F_SQUANTERR (No longer used in processing)

10 buildtype varchar2(8) flag for Canberra: activity (NONE), or concentration (BUILD), calculations

11 peak_sense number peak search sensitivity Canberra param: CAM_F_SENSITIVITY

Database Schema

548 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

TABLE 216:GARDS_SAMPLE_PROC_PARAMS (CONTINUED)

Column Storage Type Description

12 peak_start number peak search start (keV) Canberra param: CAM_L_PEAKSTART

13 peak_end number peak search end (keV) Canberra param: CAM_L_PEAKEND

14 fwhm_mult_width number number of FWHMs to search to determine multiplets Canberra param: CAM_F_PRFWHMPKMULT

15 left_fwhm_lim number left ROI FWHM limit Canberra param: CAM_F_PRFWHMPKLEFT

16 right_fwhm_lim number right ROI FWHM limit Canberra param: CAM_F_PRFWHMPKRIGHT

17 back_chan number number of continuous channels Canberra param: CAM_L_PRNBKCHN

18 back_type varchar2(6) background type: LINEAR or STEP Canberra param: CAM_T_ROIPSBTYP

19 fit_singlets number fit singlets flag Canberra param: CAM_L_PRFIT

20 crit_level number critical level test indicator Canberra param: CAM_L_CRITLEVEL

21 fix_fwhm number fixed FWHM during peak search flag Canberra param: CAM_L_PRFIXFWHM

22 area_reject number reject peaks with zero area indicator Canberra param: CAM_L_PRREJECTPEAKS

23 do_csc number flag indicating if cascade summing was turned on/off during analysis

Database Schema

IDC-5.1.1Rev5 October 2002 549 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

TABLE 216:GARDS_SAMPLE_PROC_PARAMS (CONTINUED)

Column Storage Type Description

24 mdc_width number baseline width used for MDA calculation Canberra param: CAM_F_VPWIDTH

25 lc_abscissa number abscissas of the normal distribution corresponding to a confidence level; a value of 1.645 corresponds to a 95% confidence interval for the peak critical level

26 do_pd_calc number flag that indicates if the parent/daughter calculations were run for a particular sample; 1 = calculations were run, 0 = calculations were not run

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

550 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_SAMPLE_RATIOS

The gards_sample_ratios table contains the amount of overlap between each ROI as specified in the PHD file.

TABLE 217:GARDS_SAMPLE_RATIOS

Column Storage Type Description

1 sample_id number sample identifier

2 ratio_id varchar2(15) ratio identifier

3 upper_roi_number number ROI number associated with the upper ROI

4 lower_roi_number number ROI number associated with the lower ROI

5 count_ratio number ratio of the upper ROI counts to lower ROI counts

6 count_ratio_err number uncertainty of count_ratio

Keys: Primary: sample_id/ratio_id Foreign: sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 551 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_SAMPLE_STATUS

The gards_sample_status table contains spectral processing historical data.

TABLE 218:GARDS_SAMPLE_STATUS

Column Storage Type Description

1 sample_id number sample identifier

2 entry_date date date sample was entered into database

3 cnf_begin_date date date when last analysis began

4 cnf_end_date date date when last analysis ended

5 review_date date date sample was last reviewed

6 review_time number amount of time to review sample (minutes) (no longer automatically updated)

7 analyst varchar2(30) name of analyst who reviewed sample

8 status char(1) current processing status of sample. Some possible values are: A- analyzed, P- processed, R- reviewed, U- unprocessed, V- viewed

9 category number sample categorization level after interactive analysis

10 auto_category number sample categorization level after automated analysis

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data)

Database Schema

552 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_SAMPLE_UPDATE_PARAMS

The gards_sample_update_params table holds the actual parameters used for energy calibration updating during analysis. This table may contain a combination of defaults from gards_update_params_template and values from the command line.

TABLE 219:GARDS_SAMPLE_UPDATE_PARAMS

Storage Column Description Type

1 sample_id number sample identifier

2 mrp_used number indicator of whether or not the Most Recent Prior (MRP) sample should be used

3 mrp_sample_id number the sample_id of the MRP sample to be used

4 gainshift number gain change for matching, percent (typically 0.1)

5 zeroshift number zero change for matching, channels (typically 1)

6 area_lim number minimum peak area for inclusion in matching (counts)

7 use_weight number 0/1 flag for use of weights in ECR updating (typically 1)

8 use_mult number 0/1 flag for use of multiplets in ECR updating (typically 1)

9 f_linear number 0/1 flag for forcing ECR to be first-order (typically 0)

10 bootstrap number 0/1 flag for ignoring prior ECR/ resolution versus energy regression (RER) (typically 0)

11 min_lookup number minimum library lookup tolerance, keV (typically 0.2)

12 rer_intercept number default RER intercept (typically 1.2)

13 rer_slope number default RER coeff (typically 0.03)

14 ecr_slope number default ECR slope

15 do_reru number flag that indicates if a resolution update was performed

16 rer_mrp_used number indicates what RER was chosen during analysis

Keys: Primary: sample_id Foreign: sample_id (gards_sample_data) mrp_sample_id (gards_sample_data)

Database Schema

IDC-5.1.1Rev5 October 2002 553 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_SAMPLE_XE_PROC_PARAMS

The gards_sample_xe_proc_params table contains specific processing parameters to be used for a particular spectral analysis.

TABLE 220:GARDS_SAMPLE_XE_PROC_PARAMS

Column Storage Type Description

1 sample_id number sample identifier

2 roi number ROI identifier

3 lc_abscissa number abscissa of the normal distribution corresponding to a confidence level

4 beta_ecr_order number determines whether the beta ECR is linear, quadratic, or manually defined

5 gamma_ecr_order number determines whether the gamma ECR is linear, quadratic, or manually defined

6 compton number number of compton channels

7 det_back_used number determines whether the detector background is in use or not (1 = YES, 0 = NO)

8 gas_back_used number determines whether the gas background is in use or not (1 = YES, 0 = NO)

Keys: Primary: sample_id/roi Foreign: sample_id (gards_sample_data), roi (gards_roi_lib)

Database Schema

554 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_SOH_CHAR_DATA

The gards_soh_char_data table contains all state of health (SOH) character data.

TABLE 221:GARDS_SOH_CHAR_DATA

Column Storage Type Description

1 station_id number station identifier

2 detector_id number detector identifier

3 param_code number parameter identifier

4 value varchar2(30) value of specified parameter

5 dtg_begin date begin date

6 dtg_end date end date

Keys: Primary: station_id/detector_id/param_code/dtg_begin/dtg_end

Database Schema

IDC-5.1.1Rev5 October 2002 555 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_SOH_CODE

The gards_soh_code table contains all state of health (SOH) parameter names and their codes.

TABLE 222:GARDS_SOH_CODE

Column Storage Type Description

1 param varchar2(30) SOH parameter name

2 param_code number SOH parameter code

3 param_display varchar2(30) text of the parameter to be displayed in Trendvue

4 param_display_flag number 1 or 0; if 1, then this parameter will appear in Trendvue’s menu; if 0, then it will not be displayed in Trendvue’s menu

5 display_station number 1 or 0; if 1, then the parameter is associated with a station and Trendvue will allow users to query by station; if it is 0, then this parameter is detector only and no stations will appear in the Trendvue dialog box

6 display_detector number 1 or 0; if 1, then the parameter is associated with a detector and Trendvue will allow users to query by detector; if it is 0, then this parameter is station only and no detectors will appear in the Trendvue dialog box

7 unit varchar2(32) unit that the parameter is stored in

Keys: Primary: param_code

Database Schema

556 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_SOH_HEADER

The gards_soh_header table contains the header information for all SOH messages.

TABLE 223:GARDS_SOH_HEADER

Column Storage Type Description

1 soh_id number state of health identifier

2 station_id number station identifier

3 detector_id number detector identifier

4 dtg_begin date period begin time

5 dtg_end date period end time

6 transmit_dtg date transmit date time group

Keys: Primary: soh_id Foreign: soh_id (gards_data_log.rms_id)

Database Schema

IDC-5.1.1Rev5 October 2002 557 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_SOH_NUM_DATA

The gards_soh_num_data table contains all state of health (SOH) numerical data

TABLE 224:GARDS_SOH_NUM_DATA

Column Storage Type Description

1 station_id number station identifier

2 detector_id number detector identifier

3 param varchar2(30) SOH parameter name

4 param_code number SOH parameter code

5 value number value of specified parameter

6 dtg_begin date begin date

7 dtg_end date end date

Keys: Primary: station_id/detector_id/param_code/dtg_begin/dtg_end

Database Schema

558 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_SOH_SENSOR_DATA

The gards_soh_sensor_data table contains the data reported in the #ProcessSensors data block in noble gas RMSSOH messages.

TABLE 225:GARDS_SOH_SENSOR_DATA

Column Storage Type Description

1 station_id number station identifier

2 detector_id number detector identifier

3 sensor_type varchar2(20) type of sensor (TEMP, PRESSURE, PROCESSFLOW, VOLTAGE, COUN- TRATES, DEWPOINT, CO2VOLUME)

4 sensor_name varchar2(20) unique sensor name to distinguish between sensors of the same type

5 value number sensor reading

6 dtg_begin date initial date of sensor reading

7 dtg_end date end date of sensor reading

Keys: Primary: station_id/detector_id/sensor_type

Database Schema

IDC-5.1.1Rev5 October 2002 559 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_SPECTRUM

The gards_spectrum table contains information regarding the spectral data information reported in the PHD file.

TABLE 226:GARDS_SPECTRUM

Column Storage Type Description

1 sample_id number sample identifier

2 sample_type char(1) sample type (P, G, or B)

3 filename varchar2(256) name of file containing spectrum data

4 channels number number of channels in spectrum

5 energy_span number total energy span of detector (keV)

Keys: Primary: sample_id/sample_type Foreign: sample_id (gards_sample_data)

Database Schema

560 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_STADET

The gards_stadet table contains a complete list of all station/detector identifier code combinations. The entries in this table are generated via a trigger on the gards_sample_data table.

TABLE 227:GARDS_STADET

Column Storage Type Description

1 station_id number station identifier

2 detector_id number detector identifier

Keys: Primary: detector_id/station_id Foreign: detector_id (gards_detectors), station_id (gards_stations)

Database Schema

IDC-5.1.1Rev5 October 2002 561 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_STATION_ASSIGNMENTS

The gards_station_assignments table contains a mapping of which stations are assigned to which users.

TABLE 228:GARDS_STATION_ASSIGNMENTS

Column Storage Type Description

1 station_id number station identifier

2 user_id number user identifier

Keys: Primary: station_id Foreign: station_id (gards_stations), user_id (gards_users)

Database Schema

562 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_STATIONS

The gards_stations table contains a station overview and station characteristics.

TABLE 229:GARDS_STATIONS

Column Storage Type Description

1 station_id number unique station identifier

2 station_code varchar2(5) station code

3 country_code varchar2(2) country code of site

4 type varchar2(6) station type

5 description varchar2(40) description of station

6 lat number latitude (degrees)

7 lon number longitude (degrees)

8 elevation number elevation (m)

9 date_begin date station initialization date

10 date_end date station decommissioning date

11 status varchar2(2) status of station, if NULL then station is fully operational otherwise the status is I

12 pocid number point of contact identifier

Keys: Primary: station_id Foreign: pocid (gards_poc)

Database Schema

IDC-5.1.1Rev5 October 2002 563 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_STATIONS_SCHEDULE

The gards_stations_schedule table contains schedule descriptions for stations reporting to a data center.

TABLE 230:GARDS_STATIONS_SCHEDULE

Column Storage Type Description

1 station_id number station identifier

2 begin_date date initial date of schedule

3 end_date date final date of schedule

4 code char(5) code symbol SCHEDULE as found in the gards_codes table. SF_GP for full sample grace period or SPHDF for full sample PHD

5 temporal_value number expected station schedule period

6 temporal_unit char(5) units for schedule period – currently only the value DAYS is supported

Keys: Primary: station_id/end_date Foreign: station_id (gards_stations)

Database Schema

564 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_STATUS_HISTORY

The gards_status_history table contains a list of changes in gards_sample_stations.status for reviewed samples.

TABLE 231:GARDS_STATUS_HISTORY

Column Storage Type Description

1 sample_id number foriegn key

2 user varchar2(30) user of program making status change

3 old_status char(1) sample_status before change

4 new_status char(1) sample_status after change

5 dtg date date of change

6 moddate date date of last modification

Keys: Foreign: sample_id

Database Schema

IDC-5.1.1Rev5 October 2002 565 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_TOTAL_EFFIC

The gards_total_effic table contains detector total efficiency data as specified in the PHD file.

TABLE 232:GARDS_TOTAL_EFFIC

Column Storage Type Description

1 sample_id number sample identifier

2 effic_energy number efficiency energy (keV)

3 efficiency number efficiency

4 effic_error number uncertainty of efficiency

Keys: Primary: sample_id/effic_energy Foreign: sample_id (gards_sample_data)

Database Schema

566 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_TRENDVUE

The gards_trendvue table contains data produced by the Trendvue application and is purged at the end of each session.

TABLE 233:GARDS_TRENDVUE

Column Storage Type Description

1 session_id number unique session identifier

2 date_value date date of the Trendvue plot

3 num_value1 number first plot value

4 num_value2 number second plot value

5 num_value3 number third plot value

6 num_value4 number fourth plot value

Keys: Primary: session_id

Database Schema

IDC-5.1.1Rev5 October 2002 567 GARDS_UPDATE_PARAMS_TEMPLATE

The gards_update_params_template table holds the default parameters used for energy calibration updating during analysis; these values can be overridden at the command line.

TABLE 234:GARDS_UPDATE_PARAMS_TEMPLATE

Column Storage Type Description

1 detector_id number detector identifier

2 gainshift number gain change for matching, percent (typically 0.1)

3 zeroshift number zero change for matching, channels (typically 1)

4 area_lim number minimum peak area for inclusion in matching (counts)

5 use_weight number 0/1 flag for use of weights in ECR updating (typically 1)

6 use_mult number 0/1 flag for use of multiplets in ECR updating (typically 1)

7 f_linear number 0/1 flag for forcing ECR to be first-order (typically 0)

8 bootstrap number 0/1 flag for ignoring prior ECR/RER (typically 0)

9 min_lookup number minimum library lookup tolerance, keV (typically 0.2)

10 rer_intercept number default RER intercept (typically 1.2)

11 rer_slope number default RER slope (typically 0.03)

12 do_reru number 0/1 flag that indicates whether or not a resolution update should be performed

Keys: Primary: detector_id Foreign: detector_id (gards_detectors) IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_UPDATE_REFLINES

The gards_update_reflines table contains the energies of the reference lines used in the ECR/RER updating functions.

TABLE 235:GARDS_UPDATE_REFLINES

Column Storage Type Description

1 station_id number station identifier

2 detector_id number detector identifier

3 refpeak_energy number known reference energy for a nuclide

4 data_type char(1) type of sample; an uncontaminated crushed blank filter (B), calibration background (C), detector background (D), quality control (Q), or an actual sample (S)

5 spectral_qualifier varchar2(5) time for which the sample was exposed: FULL or PREL (preliminary)

Keys: Primary: station_id/detector_id/refpeak_energy Foreign: station_id (gards_stations), detector_id (gards_detectors)

Database Schema

IDC-5.1.1Rev5 October 2002 569 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_USER_COMMENTS

The gards_user_comments table contains text associated with user-defined comments.

TABLE 236:GARDS_USER_COMMENTS

Column Storage Type Description

1 sample_id number sample identifier

2 comment_id number comment identifier

3 comment_text varchar2(512) free-form user comments

Keys: Primary: comment_id Foreign: comment_id (gards_comments)

Database Schema

570 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_USERENV

The gards_userenv table contains configurable environment variables used by the Auto- matic Processing software.

TABLE 237:GARDS_USERENV

Column Storage Type Description

1 name varchar2(40) variable name

2 value varchar2(256) variable value

Keys: Primary: name

Database Schema

IDC-5.1.1Rev5 October 2002 571 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_USERS

The gards_users table contains a list of login names for radionuclide related personnel.

TABLE 238:GARDS_USERS

Column Storage Type Description

1 user_id number unique user identifier

2 user_name varchar2(30) string name for a user database login name

3 assignable number 1 = user can be assigned stations for review or 0 = user not to be assigned stations

Keys: Primary: user_id

Database Schema

572 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_USERS_ROLES

The gards_users_roles table contains a mapping of which roles are assigned to which user.

TABLE 239:GARDS_USERS_ROLES

Column Storage Type Description

1 user_id number user identifier

2 role_id number role identifier

3 default_role number integer representation of the default role name to be assigned to the user

Keys: Primary: user_id/role_id Foreign: user_id (gards_users) role_id (gards_roles)

Database Schema

IDC-5.1.1Rev5 October 2002 573 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_XE_NUCL_LIB

The gards_xe_nucl_lib table contains nuclide library information used by the Inspectra when displaying nuclide data for gamma spectroscopy noble gas stations.

TABLE 240:GARDS_XE_NUCL_LIB

Column Storage Type Description

1 nuclide_id number nuclide identifier

2 name varchar2(8) nuclide name

3 type varchar2(16) nuclide type; choices are: ACTIVATION, COSMIC, FISSION(G), FISSION(P), or NATURAL

4 halflife_sec number half-life in seconds

5 halflife varchar2(23) half-life in seconds (S), hours (H), days (D), or years (Y)

6 halflife_err varchar2(23) uncertainty of halflife

7 num_lines number number of nuclide lines in library

Keys: Primary: name

Database Schema

574 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

GARDS_XE_NUCL_LINES_LIB

The gards_xe_nucl_lines_lib table contains nuclide library information for specific lines of a nuclide and is used by the Inspectra when displaying nuclide data for gamma spectroscopy noble gas stations.

TABLE 241:GARDS_XE_NUCL_LINES_LIB

Column Storage Type Description

1 name varchar2(8) nuclide name

2 energy number line energy (keV) Canberra parameter: CAM_F_NLENERGY

3 energy_err number uncertainty of line energy Canberra parameter: CAM_F_NLENGERR

4 abundance number abundance of line (percent) Canberra parameter: CAM_F_NLABUN

5 abundance_err number uncertainty of abundance (percent) Canberra parameter: CAM_F_NLABUNERR

6 key_flag number key line indicator Canberra parameter: CAM_L_NLFKEYLINE

7 nuclide_id number nuclide identifier Canberra parameter: CAM_L_NLNUCL

Keys: Primary: name/energy Foreign: name (gards_xe_nucl_lib)

Database Schema

IDC-5.1.1Rev5 October 2002 575 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

GARDS_XE_PROC_PARAMS_TEMPLATE

The gards_xe_proc_params_template table contains the information used for nuclide identification.

TABLE 242:GARDS_XE_PROC_PARAMS_TEMPLATE

Column Storage Type Description

1 detector_id number detector identifier

2 roi number ROI identifier

3 lc_abscissa number abscissa of the normal distribution corresponding to a confidence level

4 beta_ecr_order number determines whether the beta ECR is linear, quadratic, or manually defined

5 gamma_ecr_order number determines whether the gamma ECR is linear, quadratic or manually defined

6 compton number number of compton channels

7 det_back_used number determines whether the detector background is in use or not (1 = YES, 0 = NO)

8 gas_back_used number determines whether the gas background is in use or not (1 = YES, 0 = NO)

Keys: Primary: detector_id/roi Foreign: detector_id (gards_detectors) roi (gards_roi_lib)

Database Schema

576 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 6:

Radionuclide Table Descriptions ▼

Database Schema

IDC-5.1.1Rev5 October 2002 577 IDC DOCUMENTATION Chapter 6: User Guides

▼ Radionuclide Table Descriptions

Database Schema

578 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

Chapter 7: Radionuclide Column Descriptions

This chapter describes the columns in the radionuclide tables used at the IDC.

Database Schema

IDC-5.1.1Rev5 October 2002 579 IDC DOCUMENTATION User Guides

Chapter 7: Radionuclide Column Descriptions

Name: abscissa Table: Gards_cat_template Description: Acceptable number of standard deviations away from the central_value where the amount of a nuclide may be found (RDC algorithm). Format: number

Name: abundance Table: Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_nucl_lines_lib, Gards_sample_cert_lines, Gards_xe_nucl_lines_lib Description: Abundance of line. Format: number Units: percent

Name: abundance Table: Gards_roi_lib Description: Intensity of β-γ coincidence event. Format: number

Name: abundance_act Table: Gards_aux_lines_lib Description: Intensity of nuclear transition. Format: number

Database Schema

580 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: abundance_act_err Table: Gards_aux_lines_lib Description: Uncertainty of abundance_act. Format: number

Name: abundance_err Table: Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_nucl_lines_lib, Gards_roi_lib, Gards_xe_nucl_lines_lib Description: Uncertainty in abundance. Format: number

Name: acquisition_live_sec Table: Gards_sample_data Description: Total time a detector’s input gate is open for processing pulses. Format: number Units: seconds

Name: acquisition_real_sec Table: Gards_sample_data Description: Time difference between acquisition_stop and acquisition_start. Format: number Units: seconds

Name: acquisition_start Table: Gards_sample_data Description: Date of detector count commencement. Format: date

Database Schema

IDC-5.1.1Rev5 October 2002 581 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: acquisition_stop Table: Gards_sample_data Description: Date of detector count termination. Format: date

Name: activ_decay Table: Gards_nucl_ided, Gards_nucl_ided_orig Description: Activity decay factor. Format: number

Name: activ_decay_err Table: Gards_nucl_ided, Gards_nucl_ided_orig Description: Uncertainty in activity decay factor. Format: number

Name: activ_err Table: Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig Description: Uncertainty in activity. Format: number Units: percent

Database Schema

582 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: active_flag Table: gards_cat_criteria_tests Description: 0 if test is inactive Format: number

Name: activ_key Table: Gards_nucl_ided, Gards_nucl_ided_orig Description: Activity concentration of a radionuclide determined through the analysis of the key gamma photopeak. Format: number Units: µBq/m3

Name: activ_key_err Table: Gards_nucl_ided, Gards_nucl_ided_orig Description: Uncertainty of activ_key. Format: number (22) Units: µBq/m3

Name: activity Table: Gards_auto_sample_cat, Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_sample_cat, Gards_sample_cert_lines Description: Line activity. Format: number Units: µBq/m3

Database Schema

IDC-5.1.1Rev5 October 2002 583 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: activity Table: Gards_roi_concs Description: Activity per unit volume air. Format: number Units: µBq/m3

Name: additional_info Table: Gards_poc Description: Additional information for a contact. This column includes information such as full name, title, company or university name, country, and so on. Format: varchar2(500)

Name: address Table: Gards_poc Description: Postal address of point of contact. Format: varchar2(500)

Name: alert_text Table: Gards_alerts Description: Alert message text. Format: varchar2(512)

Name: alert_type Table: Gards_alerts Description: Category of alert. Format: varchar2(20) Range: alert_type ∈ {ALERT_FLOW, ALERT_SYSTEM, ALERT_TEMP, ALERT_UPS}

Database Schema

584 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: alpha Table: Gards_cat_template Description: Gain of first-order recursive filter for process level. Format: number Range: alpha ≥ 0

Name: analyst Table: Gards_cat_template, Gards_comments, Gards_sample_status Description: Name of IDC analyst. Format: varchar2(30)

Name: ape Table: Gards_energy_cal, Gards_energy_cal_orig Description: Average prediction error, a measure of the average confidence interval for the calculated energy versus channel regression (ECR) over the range of 100 keV. Format: number

Name: archive_bottle_id Table: Gards_sample_aux Description: Unique two-character identifier of the archive bottle in which the sample is stored. Format: char(2)

Name: area Table: Gards_peaks, Gards_peaks_orig Description: Peak area. Format: number Units: counts Range: 0 ≤ area

Database Schema

IDC-5.1.1Rev5 October 2002 585 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: area_adj Table: Gards_qcparams Description: Peak area standard deviation inflation factor. Format: number Range: 0 ≤ area_adj

Name: area_err Table: Gards_peaks, Gards_peaks_orig Description: Uncertainty of area. Format: number Units: counts Range: 0 ≤ area_err

Name: area_lim Table: Gards_sample_update_params, Gards_update_params_template Description: Minimum allowable peak size. Format: number Units: counts Range: 0 ≤ area_lim

Name: area_reject Table: Gards_proc_params_template, Gards_sample_proc_params Description: If enabled with a value of 1, this flag causes a test to be performed on peak areas. Peak areas must be positive in order to be accepted as legitimate photopeaks. A 0 value disables the test. Format: number Range: area_reject ∈ {0,1}

Database Schema

586 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: arrival_date Table: Gards_rlr Description: Sample arrival date. Format: date

Name: assay_date Table: Gards_sample_cert Description: Date of assay for a radioactive certificate source. Format: date

Name: assignable Table: Gards_users Description: Assignability flag; 1 = user can be assigned stations for review, 0 = user not to be assigned stations. Format: number

Name: auth Table: Gards_data_log Description: Authentication status of associated message; 1 = authenticated, 0 = not authenticated. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 587 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: author Table: gards_qat_notify Description: User name of radionuclide officer Format: varchar2(30)

Name: auto_category Table: Gards_sample_status Description: Sample categorization level after automated analysis. Format: number Range: 0 ≤ auto_category ≤ 5

Name: ave_activ Table: Gards_nucl_ided, Gards_nucl_ided_orig Description: Sample activity concentration of a specific radionuclide calculated by averag- ing all activity values. Format: number Units: µBq/m3

Name: ave_activ_err Table: Gards_nucl_ided, Gards_nucl_ided_orig Description: Uncertainty of ave_activ. Format: number Units: µBq/m3 Range: 0 ≤ ave_activ_err

Database Schema

588 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: ave_humidity Table: Gards_met_data Description: Average humidity. Format: number Units: percent

Name: ave_out_temp Table: Gards_met_data Description: Average outside temperature. Format: number Units: degrees C

Name: ave_pressure Table: Gards_met_data Description: Average atmospheric pressure. Format: number Units: millibars Range: 0.0 ≤ ave_pressure

Name: ave_wind_dir Table: Gards_met_data Description: Average wind direction, degrees from true North. Format: number Units: degrees Range: 0.0 ≤ ave_wind_dir ≤ 360.0

Database Schema

IDC-5.1.1Rev5 October 2002 589 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: ave_wind_speed Table: Gards_met_data Description: Average wind speed. Format: number Units: km/hour

Name: b_abundance Table: Gards_sample_cert_lines Description: Intensity of beta particle or conversion electron. Format: number Units: particles/decay

Name: b_chan_start Table: Gards_roi_channels Description: Beta boundary start channel. Format: number

Name: b_chan_stop Table: Gards_roi_channels Description: Beta boundary stop channel. Format: number

Name: b_channels Table: Gards_histogram Description: Number of beta channels in histogram. Format: number

Database Schema

590 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: b_energy Table: Gards_sample_cert_lines Description: Energy of conversion electron or maximum energy of beta particle. Format: number Units: keV

Name: b_energy_span Table: Gards_histogram Description: Beta energy span of detector calibration. Format: number Units: keV

Name: b_energy_start Table: Gards_roi_limits Description: Beta boundary start energy. Format: number Units: keV

Name: b_energy_stop Table: Gards_roi_limits Description: Beta boundary stop energy. Format: number Units: keV

Database Schema

IDC-5.1.1Rev5 October 2002 591 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: back_chan Table: Gards_proc_params_template, Gards_sample_proc_params Description: Number of channels to be used on either side of a ROI in calculating the continuum (or baseline) during automatic analysis. Format: number Range: 0.0 ≤ back_chan

Name: back_channel Table: Gards_peaks, Gards_peaks_orig Description: Average number of background channels. Format: number Range: 0.0 ≤ back_channel

Name: back_count Table: Gards_peaks, Gards_peaks_orig Description: Continuum background counts. Format: number Range: 0.0 ≤ back_count

Name: back_data_type Table: Gards_proc_params_template, Gards_sample_proc_params Description: Parameter that designates the PHD type to be used for a background subtraction (controlled by the do_back column): B indicates BLANKPHD and D indicates DETBKPHD. Format: char(1) Range: back_data_type ∈ {B, D}

Database Schema

592 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: back_sample_id Table: Gards_sample_proc_params Description: sample_id of the most recent background count. This count is used for background subtraction when the background subtraction function is ON. Format: number Range: 0 ≤ back_sample_id

Name: back_type Table: Gards_proc_params_template, Gards_sample_proc_params Description: Type of baseline available, LINEAR or STEP. Format: varchar(6) Range: back_type ∈ {LINEAR, STEP}

Name: back_uncer Table: Gards_peaks, Gards_peaks_orig Description: Uncertainty in back_count. Format: number Units: counts Range: 0.0 ≤ back_uncer

Name: begin_date Table: Gards_cat_template, Gards_proc_params_template, Gards_stations_schedule Description: Indicator of either the date when the data record became active and was used for processing data, or the initial date of a station’s schedule. Format: date

Database Schema

IDC-5.1.1Rev5 October 2002 593 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: beta_coeff1 Table: Gards_bg_energy_cal Description: Zero shift of the beta ECR equation. Format: number

Name: beta_coeff2 Table: Gards_bg_energy_cal Table: Linear coefficient of the beta ECR equation. Format: number

Name: beta_coeff3 Table: Gards_bg_energy_cal Description: Quadratic coefficient of the beta ECR equation. Format: number

Name: beta_ecr_order Table: Gards_sample_xe_proc_params, Gards_xe_proc_params_template Description: Determines whether or not the beta ecr is linear, quadratic, or manually defined; 1 = linear, 2 = quadratic, 3 = manual (ecr is set on the command line). Format: number

Name: bg_effic_error Table: Gards_bg_efficiency_pairs Description: Uncertainty of bg_efficiency. Format: number

Database Schema

594 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: bg_efficiency Table: Gards_bg_efficiency_pairs Description: Detection efficiency of β-γ coincidence event. Format: number

Name: bkgd_measurement_id Table: Gards_sample_aux Description: Unique background identifier corresponding to the detection identifier. Format: varchar2(31)

Name: bootstrap Table: Gards_sample_update_params, Gards_update_params_template Description: Flag for ignoring prior ECR/RER. A value of 0 indicates not ignore, 1 indicates ignore. Format: number Range: bootstrap ∈ {0, 1}

Name: branch_ratio Table: Gards_aux_lib Description: Percentage of decays to given decay path. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 595 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: buildtype Table: Gards_sample_update_params, Gards_update_params_template Description: Indicator of the units of the spectral analysis results. "BUILD" is used for normal sample analysis and returns air activity concentrations, µBq/m3. “NONE” is used for BLANKPHDs, CALIBPHDs, DETBKPHDs, and QCPHDs and returns analysis results as activity values, µBq. Format: varchar2(8) Range: buildtype ∈ {BUILD, NONE}

Name: cal_energy Table: Gards_b_energy_pairs, Gards_b_energy_pairs_orig, Gards_energy_pairs, Gards_energy_pairs_orig Description: Calibration energy. Format: number Units: keV

Name: cal_error Table: Gards_b_energy_pairs, Gards_b_energy_pairs_orig, Gards_energy_pairs, Gards_energy_pairs_orig Description: Uncertainty of channel. Format: number Units: keV

Name: calibration_dtg Table: Gards_sample_aux Description: Date of most recent calibration at a detector site. Format: date

Database Schema

596 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: calibration_type Table: Gards_refline_master Description: Calibration type indicator. MIX indicates a mixed source, CAL indicates a single radionuclide source, and no entry indicates the calibration_type is an actual air sample. Format: varchar2(3) Range: calibration_type ∈ {MIX, CAL}

Name: category Table: Gards_auto_sample_cat, Gards_sample_cat, Gards_sample_status Description: Categorization level. Format: number Range: 0 ≤ category ≤ 5

Name: category_list Table: Gards_qat_query_filter Description: comma-separated list of categories Format: varchar2(32)

Name: central_value Table: Gards_auto_sample_cat, Gards_cat_template, Gards_sample_cat Description: Estimate of the level of the random process. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 597 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: centroid Table: Gards_peaks, Gards_peaks_orig Description: Peak centroid energy. Format: number Units: KeV Range: 0.0 ≤ centroid

Name: centroid_err Table: Gards_peaks, Gards_peaks_orig Description: Uncertainty of centriod. Format: number Units: channels Range: 0.0 ≤ centroid_err

Name: chain_id Table: Gards_aux_lib Description: Decay chain index. Format: number

Name: chain_pos Table: Gards_aux_lib Description: Position in decay chain. Format: number

Database Schema

598 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: channel Table: Gards_b_energy_pairs, Gards_b_energy_pairs_orig, Gards_energy_pairs, Gards_energy_pairs_orig Description: Peak centroid channel. Format: number

Name: channels Table: Gards_detectors, Gards_spectrum Description: Number of channels. Format: number Range: channels > 0

Name: class Table: Gards_interval Description: Station name. Format: varchar2(16)

Name: cnf_begin_date Table: Gards_sample_status Description: Date when last analysis began. Format: date

Name: cnf_end_date Table: Gards_sample_status Description: Date when last analysis ended. Format: date

Database Schema

IDC-5.1.1Rev5 October 2002 599 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: cnv_factor Table: Gards_energy_cal, Gards_energy_cal_orig Description: Conversion factor from MeV to keV. Format: number Units: keV/MeV

Name: code Table: Gards_codes Description: Code symbol. Format: char(5)

Name: code Table: Gards_stations_schedule Description: Code symbol SCHEDULE as found in the gards_codes table. SF_GP for full sample grace period or SPHDF for full sample PHD. Format: char(5) Range: code ∈ {SF_GP, SPHDF}

Name: coeff1 Table: Gards_efficiency_cal, Gards_energy_cal, Gards_energy_cal_orig, Gards_resolution_cal, Gards_resolution_cal_orig Description: First order calibration coefficient. Format: number

Name: coeff2 Table: Gards_efficiency_cal, Gards_energy_cal, Gards_energy_cal_orig, Gards_resolution_cal, Gards_resolution_cal_orig Description: Second order calibration coefficient. Format: number

Database Schema

600 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: coeff3 Table: Gards_efficiency_cal, Gards_energy_cal, Gards_energy_cal_orig, Gards_resolution_cal, Gards_resolution_cal_orig Description: Third order calibration coefficient. Format: number

Name: coeff4 Table: Gards_efficiency_cal, Gards_energy_cal, Gards_energy_cal_orig, Gards_resolution_cal, Gards_resolution_cal_orig Description: Fourth order calibration coefficient. Format: number

Name: coeff5 Table: Gards_efficiency_cal, Gards_energy_cal, Gards_energy_cal_orig, Gards_resolution_cal, Gards_resolution_cal_orig Description: Fifth order calibration coefficient. Format: number

Name: coeff6 Table: Gards_efficiency_cal, Gards_energy_cal, Gards_energy_cal_orig, Gards_resolution_cal, Gards_resolution_cal_orig Description: Sixth order calibration coefficient. Format: number

Name: coeff7 Table: Gards_efficiency_cal, Gards_energy_cal, Gards_energy_cal_orig, Gards_resolution_cal, Gards_resolution_cal_orig Description: Seventh order calibration coefficient. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 601 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: coeff8 Table: Gards_efficiency_cal, Gards_energy_cal, Gards_energy_cal_orig, Gards_resolution_cal, Gards_resolution_cal_orig Description: Eighth order calibration coefficient. Format: number

Name: collect_start Table: Gards_rlr, Gards_sample_data Description: Date of sample collection commencement. Format: date

Name: collect_stop Table: Gards_rlr, Gards_sample_data Description: Date of sample collection termination. Format: date

Name: comment_id Table: Gards_comments, Gards_user_comments Description: Unique comment identifier. Format: number

Name: comment_text Table: Gards_cat_template, Gards_comments_defs, Gards_qat_notify, Gards_user_comments Description: Text of analyst comments. Format: varchar2(256) for gards_comments_defs, gards_cat_template, varchar2(512) for gards_user_comments, varchar2(2048) for gards_qat_notify.

Database Schema

602 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: comment_type Table: Gards_comments, Gards_comments_defs, Gards_qat_notify Description: Predefined comment code. Format: number

Name: comp_confid Table: Gards_nucl_ided, Gards_nucl_ided_orig Description: Computed confidence index. Format: number

Name: compton Table: Gards_roi_counts, Gards_sample_xe_proc_params, Gards_xe_proc_params_template Description: Compton continuum background counts. Format: number Units: counts

Name: compton_err Table: Gards_roi_counts Description: Uncertainty of compton. Format: number Units: counts

Name: count_ratio Table: Gards_sample_ratios Description: Ratio of upper ROI counts to lower ROI counts. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 603 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: count_ratio_err Table: Gards_sample_ratios Description: Uncertainty of count_ratio. Format: number

Name: country_code Table: Gards_stations Description: Unique two-digit identifier for the country in which the station is located. Format: varchar2(2)

Name: count_sec Table: Gards_peaks, Gards_peaks_orig Description: Count rate. Format: number Units: counts/second

Name: count_sec_err Table: Gards_peaks, Gards_peaks_orig Description: Uncertainty of count rate. Format: number Units: percent

Name: crit_level Table: Gards_proc_params_template, Gards_sample_proc_params Description: If set to 1, the estimated net areas are subjected to a simple "Critical Level Test" to see if they are above a multiple of the ROI baseline-area’s estimated variability. This column is a form of "signal-to-noise" test. The indicated area

Database Schema

604 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

must be at least 1.645 (hardcoded) times the estimated standard deviation of the baseline area for the peak to be accepted. If the area fails the test, it is deleted from the peak search results. Format: number Range: crit_level ∈ {0, 1}

Name: csc_mod_flag Table: gards_nucl_ided, gards_nucl_lines_ided Description: flag that indicates if cascade summing modified a nuclide: 1 = nuclide was modified, 0 = nuclide was not modified. Format: number

Name: csc_ratio Table: gards_nucl_ided, gards_nucl_lines_ided Description: multiplier used by analysis to update activ_key and mda. Format: number

Name: csc_ratio_err Table: gards_nucl_ided, gards_nucl_lines_ided Description: uncertainty in csc_ratio. Format: number

Name: data_type Table: Gards_proc_params_template, Gards_refline_master, Gards_sample_data, Gards_update_reflines Description: Type of sample; an uncontaminated crushed blank filter (B), calibration background (C), detector background (D), quality control (Q), or an actual sample (S). Format: char(1) Range: data_type ∈ {B, C, D, Q, S}

Database Schema

IDC-5.1.1Rev5 October 2002 605 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: data_type Table: Gards_data_log , Gards_processing_errors Description: Type of data message. Format: varchar2(10); varchar2(12) Range: data_type ∈ {ALERT, MET, SOH, SPHD-B, SPHD-C, SPHD-D, SPHD-F, SPHD-P, SPHD-Q, SPHD-G.}

Name: date_begin Table: Gards_detectors, Gards_stations Description: Station/Detector initialization date. Format: date

Name: date_end Table: Gards_detectors, Gards_stations Description: Station/Detector decommissioning date. Format: date

Name: date_received Table: Gards_data_log Description: Date message arrival date. Format: date

Name: date_value Table: Gards_trendvue Description: Date of Trendvue plot. Format: date

Database Schema

606 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: db_name Table: Gards_permissions, Gards_roles Description: Name of corresponding database role. Format: varchar2(35)

Name: decay_mode Table: Gards_b_energy_pairs, Gards_b_energy_pairs_orig, Gards_sample_cert_lines Description: Type of decay; B = beta particle, C = conversion electron. Format: char(1) Range: decay_mode ∈ {B, C}

Name: default_role Table: Gards_users_roles Description: Number that corresponds to the default role id for a user. Format: number

Name: degree Table: Gards_efficiency_cal Description: Degree of efficiency equation. Format: number

Name: delta Table: Gards_auto_sample_cat, Gards_cat_template, Gards_sample_cat Description: Value of a variable used in bounds estimation (EWMA algorithm). Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 607 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: description Table: Gards_notify Description: Reason a notification message is transmitted. Format: varchar2(80)

Name: description Table: Gards_codes, Gards_detectors, Gards_stations Description: Description of the code, detector, or station. Format: varchar2(40) varchar2(80) for gards_detectors

Name: description Table: Gards_sample_description Description: Description sent from the station in a Comment block of a PHD message. Format: varchar2(512)

Name: det Table: Gards_energy_cal, Gards_energy_cal_orig Description: The determinant of the weighted design matrix, a measure of the spread of fitted data points and the error in the fitted points. Format: number

Name: det_back_used Table: Gards_sample_xe_proc_params, Gards_xe_proc_params_template Description: Determines whether the detector background is in use or not (1 = YES, 0 = NO). Format: number

Database Schema

608 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: detector_back Table: Gards_roi_counts Description: Detector background counts. Format: number

Name: detector_back_err Table: Gards_roi_counts Description: Uncertainty of detector_back. Format: number Units: counts

Name: detector_code Table: Gards_detectors, Gards_processing_errors Description: Detector identification code. Format: varchar2(9)

Name: detector_id Table: Gards_cat_template, Gards_detectors, Gards_nucl_ided, Gards_nucl_ided_orig, Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_proc_params_template, Gards_qchistory, Gards_qcparams, Gards_qctargets, Gards_rlr, Gards_sample_data, Gards_soh_char_data, Gards_soh_header, Gards_soh_num_data, Gards_soh_sensor_data, Gards_stadet, Gards_update_params_template, Gards_update_reflines, Gards_xe_proc_params_template Description: Unique detector identifier. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 609 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: display_detector Table: Gards_soh_code Description: Flag indicating if the SOH parameter is associated with a detector; 1 = the parameter is associated with a detector and Trendvue should allow users to query by detector, 0 = the parameter is station only and no detectors will appear in the Trendvue dialog box. Format: number

Name: display_station Table: Gards_soh_code Description: Flag indicating if the SOH parameter is associated with a station; 1 = the parameter is associated with a station and Trendvue should allow users to query by station, 0 = the parameter is detector only and no stations will appear in the Trendvue dialog box. Format: number

Name: dlid Table: Gards_data_log Description: Data log identifier. Format: number

Name: do_back Table: Gards_proc_params_template, Gards_sample_proc_params Description: Flag that indicates whether or not background subtraction should be performed: 1 = yes, 0 = no. Format: number Range: do_back ∈ {0,1}

Database Schema

610 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: do_csc Table: gards_proc_params_template, gards_sample_proc_params Description: flag that indicates how cascade summing should default: 0 = defaul to off, 1 = default to on. Format: number

Name: do_pd_calc Table: Gards_proc_params_template, Gards_sample_proc_params Description: Flag that indicates if the parent/daughter calculations were run for a particular sample; 1 = calculations were run, 2 = calculations were not run. Format: number

Name: do_reru Table: Gards_update_params_template, Gards_sample_update_params Description: Flag that indicates if the software is to perform a resolution update. Format: number Range: do_reru ∈ {0,1}

Name: dtg Table: Gards_alerts, Gards_comments, Gards_data_log, Gards_fpe, Gards_qat_notify, Gards_qctargets, Gards_receipt_log, Gards_status_history. Description: Date of the event, comment, message, or change. Format: date

Database Schema

IDC-5.1.1Rev5 October 2002 611 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: dtg_begin Table: Gards_mdas2report, Gards_notify, Gards_nucl2quantify, Gards_soh_char_data, Gards_soh_header, Gards_soh_num_data, Gards_soh_sensor_data Description: Start date of applicability, notification initialization date, or the reporting period. Format: date

Name: dtg_end Table: Gards_mdas2report, Gards_notify, Gards_nucl2quantify, Gards_soh_char_data, Gards_soh_header, Gards_soh_num_data, Gards_soh_sensor_data Description: End date of applicability, notification termination date, or the reporting period. Format: date

Name: ecal_range_max Table: Gards_detectors Description: Maximum detector calibration energy for which the detector is calibrated. Format: number Units: keV

Name: ecr_slope Table: Gards_sample_update_params Description: Default ECR slope. Format: number

Database Schema

612 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: eff_error Table: Gards_peaks, Gards_peaks_orig Description: Uncertainty of efficiency. Format: number

Name: effic Table: Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig Description: Efficiency at energy. Format: number

Name: effic_energy Table: Gards_efficiency_pairs, Gards_total_effic Description: Efficiency energy. Format: number Units: keV

Name: effic_err Table: Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig Description: Uncertainty of effic. Format: number

Name: effic_error Table: Gards_efficiency_pairs, Gards_total_effic Description: Uncertainty of efficiency. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 613 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: efficiency Table: Gards_efficiency_pairs, Gards_peaks, Gards_peaks_orig, Gards_total_effic Description: Peak efficiency. Format: number

Name: efftype Table: Gards_efficiency_cal Description: Efficiency type. Format: char(8)

Name: elevation Table: Gards_stations Description: Elevation of the station location above sea level. Format: number Units: meters Range: 0 ≥ elevation

Name: email_addr Table: Gards_notify Description: Recipient email address. Format: varchar2(80)

Name: email_address Table: Gards_poc Description: Email address of the point-of-contact. Format: varchar2(50)

Database Schema

614 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: end_date Table: Gards_cat_template, Gards_proc_params_template, Gards_stations_schedule Description: In gards_proc_params_template, this column indicates when a data record became inactive. If the value of the date is NULL, then the record is still active. In gards_stations_schedule, this column contains the date of station termination. Format: date

Name: end_env_time Table: Gards_environment Description: End date of environmental data. Format: date

Name: end_env_time_sec Table: Gards_environment Description: End date of environmental data. Format: number Units: seconds

Name: end_time Table: Gards_met_data Description: End time of measurement. Format: date

Name: end_time Table: Gards_interval Description: End time of interval in epoch time. Format: float(22)

Database Schema

IDC-5.1.1Rev5 October 2002 615 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: energy Table: Gards_aux_lines_lib, Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_nucl_lines_lib, Gards_peaks, Gards_peaks_orig, Gards_qat_notify, Gards_qctargets, Gards_sample_cert_lines, Gards_xe_nucl_lines_lib Description: Line energy. Format: number Units: keV Range: 0 ≤ energy

Name: energy_err Table: Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_nucl_lines_lib, Gards_peaks, Gards_peaks_orig, Gards_xe_nucl_lines_lib Description: Uncertainty of energy. Format: number Units: keV Range: 0.0 ≤ energy_err

Name: energy_span Table: Gards_spectrum Description: Total energy span of detector. Format: number Units: keV

Database Schema

616 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: energy_tol Table: Gards_sample_proc_params Description: Column used during nuclide identification. Nuclides with photopeaks within energy_tol (keV) of the given centroid energy will be tentatively associated with the peak. Format: number Units: keV Range: 0.0 ≤ energy_tol

Name: energy_units Table: Gards_energy_cal, Gards_energy_cal_orig Description: Energy units. Format: char(3) Range: energy_units ∈ {MeV, keV}

Name: entry_date Table: Gards_sample_status, Gards_processing_errors Description: Date sample was entered into database; date and time of error entry Format: date

Name: error Table: Gards_sample_cert_lines Description: Uncertainty of activity. Format: number Units: percent Range: 0.0 ≤ error

Database Schema

IDC-5.1.1Rev5 October 2002 617 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: error_text Table: Gards_processing_errors Description: Text associated with the error Format: varchar2(2048)

Name: etol Table: Gards_qcparams Description: Energy tolerance used to match peaks with energies. Format: number Range: 0.0 ≤ etol

Name: event Table: Gards_notify Description: Type of occurrence. Format: varchar2(10) Range: event ∈ {ALERT, FIS_FOUND, NIC_SIG34, NIC_SIG5, QC_ERROR, QC_WARNING, RADOPSCAL, RMS_ADMIN}

Name: f_linear Table: Gards_sample_update_params, Gards_update_params_template Description: Flag for forcing ECR to be first ordered. A value of 0 indicates not to force, 1 indicates to force the ECR. Format: number Range: f_linear ∈ {0,1}

Database Schema

618 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: file_size Table: Gards_data_log Description: Data message size. Format: number Units: kilobytes

Name: filename Table: Gards_histogram, Gards_rlr, Gards_spectrum, Gards_processing_errors Description: Name of file containing associated data; import message filename Format: varchar2(256); varchar2(512)

Name: first_name Table: Gards_poc Description: Point of contact’s first name. Format: varchar2(20)

Name: fit_singlets Table: Gards_proc_params_template, Gards_sample_proc_params Description: Flag that indicates the type of processing performed when searching for singlets. 0 indicates a simple arithmetic summation of the ROI channel data is used to estimate the centroid, width, and area of a peak. 1 indicates a non-linear Gaussian fit is used to estimate the peak centroid, width, and area. Format: number Range: fit_singlets ∈ {0,1}

Database Schema

IDC-5.1.1Rev5 October 2002 619 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: fitted Table: Gards_peaks, Gards_peaks_orig Description: Peak fit indicator. 0 indicates the peak fit function is OFF. 1 indicates the peak fit function is ON. Format: number Range: fitted ∈ {0,1}

Name: fix_fwhm Table: Gards_proc_params_template, Gards_sample_proc_params Description: If the value for this variable is 1, the width of a peak will be "fixed" at the value predicted by the RER at the energy of interest. A 0 indicates that the peak width is a free parameter and will be estimated. Format: number Range: fix_fwhm ∈ {0,1}

Name: flag_id Table: Gards_flags, Gards_sample_flags Description: Unique identifier for an event screening test. Format: number Range: 0 ≤ flag_id

Name: flow_rate Table: Gards_environment Description: Flow rate through filter. Format: number Units: m3/h Range: 0.0 ≤ flow_rate

Database Schema

620 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: fpid Table: Gards_fpe Description: Unique fission product identifier. Format: number Range: 0 ≤ gards_fpe

Name: fwhm Table: Gards_peaks, Gards_peaks_orig Description: Peak width at half the maximum peak height. Format: number Units: keV Range: 0.0 ≤ fwhm

Name: fwhm_err Table: Gards_peaks, Gards_peaks_orig Description: Uncertainty in fwhm. Format: number Units: KeV Range: 0.0 ≤ fwhm_err

Name: fwhm_mult_width Table: Gards_proc_params_template, Gards_sample_proc_params Description: Number of full-width-at-half-maximums to search to determine multiplets during peak searches (a user configurable value). Format: number Range: 0 ≤ fwhm_mult_width

Database Schema

IDC-5.1.1Rev5 October 2002 621 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: g_chan_start Table: Gards_roi_channels Description: Gamma boundary start channel. Format: number

Name: g_chan_stop Table: Gards_roi_channels Description: Gamma boundary stop channel. Format: number

Name: g_channels Table: Gards_histogram Description: Number of gamma channels in histogram. Format: number

Name: g_energy_span Table: Gards_histogram Description: Gamma energy span of detector. Format: number Units: keV

Name: g_energy_start Table: Gards_roi_limits Description: Gamma boundary start energy. Format: number Units: keV

Database Schema

622 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: g_energy_stop Table: Gards_roi_limits Description: Gamma boundary stop energy. Format: number Units: keV

Name: gainchange Table: Gards_qcparams Description: Acceptable change in gain for a quality control (QC) test. Format: number

Name: gainshift Table: Gards_update_params_template, Gards_sample_update_params Description: Gainshift observed between one spectrum and the spectrum that follows. Used during matching peaks. Format: number Units: percent Range: 0.0 ≤ gainshift

Name: gamma Table: Gards_cat_template Description: Gain of first-order recursive filter for process variance. Format: number Range: 0.0 ≤ gamma

Database Schema

IDC-5.1.1Rev5 October 2002 623 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: gamma_coeff1 Table: Gards_bg_energy_cal Description: Gain of the gamma ECR equation. Format: number

Name: gamma_coeff2 Table: Gards_bg_energy_cal Description: Linear coefficient of the gamma ECR equation. Format: number

Name: gamma_coeff3 Table: Gards_bg_energy_cal Description: Quadratic coefficient of the gamma ECR equation. Format: number

Name: gamma_ecr_order Table: Gards_sample_xe_proc_params, Gards_xe_proc_params_template Description: Determines whether the gamma ecr is linear, quadratic, or manually defined; 1 = linear, 2 = quadratic, 3 = manual (ecr is set on command line). Format: number

Name: gas_back_used Table: Gards_sample_xe_proc_params, Gards_xe_proc_params_template Description: Determines whether or not the gas background is in use (1 = YES, 0 = NO). Format: number

Database Schema

624 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: gas_bkgd_measurement_id Table: Gards_sample_aux Description: Unique measurement of the gas background acquisition associated with the sample. Format: varchar2(31)

Name: geometry Table: Gards_sample_data Description: Sample geometry. Format: varchar2(17)

Name: gross Table: Gards_roi_counts Description: Counts in ROI before processing. Format: number Units: counts

Name: gross_err Table: Gards_roi_counts Description: Uncertainty of gross. Format: number Units: counts

Database Schema

IDC-5.1.1Rev5 October 2002 625 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: halflife Table: Gards_nucl_ided, Gards_nucl_ided_orig, Gards_nucl_lib, Gards_roi_lib, Gards_sample_cert_lines, Gards_xe_nucl_lib Description: Half-life of a radionuclide given as a number (integer, decimal, or exponential) followed by a time unit such as S for seconds, H for hours, D for days, or Y for years. Format: varchar2(23)

Name: halflife_act Table: Gards_aux_lib Description: Actual half-life. Format: varchar2(23)

Name: halflife_act_err Table: Gards_aux_lib Description: Uncertainty of halflife_act. Format: varchar2(23)

Name: halflife_err Table: Gards_nucl_lib, Gards_roi_lib, Gards_xe_nucl_lib Description: Uncertainty of halflife. Format: varchar2(23)

Name: halflife_sec Table: Gards_nucl_lib, Gards_roi_lib, Gards_xe_nucl_lib Description: Half-life in seconds. Format: number Units: seconds

Database Schema

626 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: hold Table: Gards_auto_sample_cat, Gards_sample_cat Description: Flag that holds categorization bounds fixed and does not update values. A value of 1 means to proceed as usual, 0 means to wait. Format: number Range: hold ∈ {0,1}

Name: ided Table: Gards_peaks, Gards_peaks_orig Description: Peak identification indicator. 1 = peak was associated with a nuclide by the automated analysis. 0 = peak was not associated with a nuclide by the automated analysis. This field is not updated by the ROI interface. Format: number Range: ided ∈ {0,1}

Name: include_stations Table: Gards_qat_query_filter Description: flag to include or exclude stations Format: number

Name: init_begin_date Table: Gards_cat_template Description: Start date for initialization data. Format: date

Name: init_end_date Table: Gards_cat_template Description: End date for initialization data. Format: date

Database Schema

IDC-5.1.1Rev5 October 2002 627 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: input_file_name Table: Gards_sample_data Description: Name of data file to be input. Format: varchar2(256)

Name: interference Table: Gards_roi_counts Description: Counts from interference nuclides. Format: number Units: counts

Name: interference_err Table: Gards_roi_counts Description: Uncertainty of interference. Format: number Units: counts

Name: kb_sent Table: Gards_receipt_log Description: Size of data sent. Format: number Units: kilobytes Range: kb_sent > 0

Database Schema

628 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: key_flag Table: Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_nucl_lines_lib, Gards_xe_nucl_lines_lib Description: Flag that indicates whether the photopeak is a key line (1) or not (0). Format: number Range: key_flag ∈ {0,1}

Name: last_name Table: Gards_poc Description: Last name of the point of contact. Format: varchar2(50)

Name: lat Table: Gards_detectors, Gards_stations Description: Geographic latitude of the detector or station. Format: number Units: degrees Range: 90.0 > lat > –90.0

Name: lc Table: Gards_peaks, Gards_peaks_orig, Gards_roi_counts Description: Critical level for the peak. Format: number Units: counts

Database Schema

IDC-5.1.1Rev5 October 2002 629 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: lc_abscissa Table: Gards_proc_params_template, Gards_sample_proc_params, Gards_sample_xe_proc_params, Gards_xe_proc_params_template Description: Abscissas of the normal distribution corresponding to a confidence level; a value of 1.645 corresponds to a 95% confidence interval for the peak critical level. Format: number

Name: lddate Table: Gards_interval, Gards_qchistory Description: Load date of record. Format: date

Name: left_chan Table: Gards_peaks, Gards_peaks_orig Description: Left channel of peak I. Format: number Range: left_chan > 0

Name: left_fwhm_lim Table: Gards_proc_params_template, Gards_sample_proc_params Description: One of two user-configurable limits on the peak size. This column indicates the maximum possible peak width to the left of the peak centroid, expressed in multiples of the FWHM. Format: number Range: left_fwhm_lim > 0

Database Schema

630 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: line_comment Table: Gards_aux_lines_lib Description: Description of line properties. Format: varchar2(500)

Name: line_type Table: Gards_aux_lines_lib Description: Type of radiation causing the line. Format: varchar2(8)

Name: lon Table: Gards_detectors, Gards_stations Description: Geographic longitude of the detector or station. Format: number Units: degrees Range: –180.0 > lon > 180.0

Name: lower_bound Table: Gards_auto_sample_cat, Gards_cat_template, Gards_sample_cat Description: Lower limit of the amount of a nuclide that can be acceptably found. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 631 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: lower_limit Table: Gards_cat_criteria_tests Description: lower limit bound of the test Format: number

Name: lower_roi_number Table: Gards_sample_ratios Description: ROI number associated with the lower ROI. Format: number

Name: max_sample_id Table: Gards_qat_query_filter Description: foriegn key Format: number

Name: max_t_time Table: Gards_qat_config Description: maximum allowable value for t_time Format: number

Name: mda Table: Gards_nucl_ided, Gards_nucl_ided_orig, Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_roi_concs Description: Minimum detectable activity. Format: number Units: µBq/m3 mBq/m3 for gards_roi_concs Range: mda ≥ 0.0

Database Schema

632 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: mda_err Table: Gards_nucl_ided, Gards_nucl_ided_orig Description: Uncertainty of mda. Format: number Units: µBq/m3 Range: mda_err ≥ 0

Name: mda_level Table: Gards_proc_params_template, Gards_sample_proc_params Description: Confidence level at which the minimum detectable concentration is calculated. The value represents a value to be subtracted from 100%, resulting in a confidence level of 1–100%. Format: number Range: 1.0 ≤ mda_level ≤ 100.0

Name: mda_max Table: Gards_mdas2report Description: Maximum bound for the MDC range. Format: number Units: µBq/m3 Range: 5 ≤ mda_max ≤ 22000

Name: mda_min Table: Gards_mdas2report Description: Minimum bound for the minimum detectable activity (MDA) range. Format: number Units: µBq/m3 Range: 3 ≤ mda_min ≤ 22000

Database Schema

IDC-5.1.1Rev5 October 2002 633 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: mdc_width Table: Gards_proc_params_template, Gards_sample_proc_params Description: Baseline width used for MDA calculation. Format: number

Name: measurement_id Table: Gards_sample_aux Description: Unique alphanumeric identifier assigned to each detector acquisition. Format: varchar2(31)

Name: memory Table: Gards_roi_counts Description: Gas background (that is, “memory effect”) counts. Format: number Units: counts

Name: memory_err Table: Gards_roi_counts Description: Uncertainty of memory. Format: number Units: counts

Name: method_id Table: Gards_auto_sample_cat, Gards_cat_template, Gards_sample_cat Description: Method identifier. Format: number

Database Schema

634 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: method_type Table: Gards_cat_template Description: Type of categorization analysis to use. Format: number

Name: min_lookup Table: Gards_sample_update_params, Gards_update_params_template Description: Minimum value possible for the nuclide library lookup energy tolerance, energy_tol. The energy_tol cannot be less than min_lookup and result in a match. Format: number

Name: min_sample_id Table: Gards_qat_query_filter Description: foreign key Format: number

Name: min_t_time Table: gards_qat_config Description: minimum allowable value for t_time Format: number

Name: moddate Table: Gards_cat_criteria_tests, Gards_interval, Gards_qat_config, Gards_qat_notify, Gards_status_history Description: Modification date. Format: date

Database Schema

IDC-5.1.1Rev5 October 2002 635 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: mrp_sample_id Table: Gards_sample_update_params Description: Column that lists the sample_id of the MRP sample in the event that the mrp_used flag has been set to 1. Format: number Range: mrp_sample_id ≥ 0

Name: mrp_used Table: Gards_sample_update_params Description: Flag that indicates when the most recent prior sample should be taken into account during sample processing. 1 = should be used. 0 = should not be used. Format: number Range: mrp_used ∈ {0,1}

Name: mse Table: Gards_energy_cal, Gards_energy_cal_orig Description: The mean-squared error of the fit; a measure of how large the residual is. Format: number

Name: msg_id Table: Gards_data_log, Gards_sample_aux , Gards_processing_errors Description: Message identifier sent in the email header of the message. Format: number Range: msg_id ≥ 0

Database Schema

636 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: muarea Table: Gards_qctargets Description: Target area for each nuclide line energy. Format: number Units: counts Range: muarea > 0

Name: multiplet Table: Gards_peaks, Gards_peaks_orig Description: Multiplet peak indicator. Format: number Range: multiplet ∈ {0,1}

Name: muwidth Table: Gards_qctargets Description: Target width for each nuclide line indicator. Format: number Units: keV Range: muwidth > 0.0

Name: name Table: Gards_auto_sample_cat, Gards_aux_lib, Gards_aux_lines_lib, Gards_cat_template, Gards_mdas2report, Gards_nucl2quantify, Gards_nucl_ided, Gards_nucl_ided_orig, Gards_nucl_lib, Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_nucl_lines_lib, Gards_qctargets, Gards_relevant_nuclides, Gards_roi_lib, Gards_sample_cat, Gards_xe_nucl_lib, Gards_xe_nucl_lines_lib Description: Nuclide name. Format: varchar2(8)

Database Schema

IDC-5.1.1Rev5 October 2002 637 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: name Table: Gards_flags Description: Test name. Format: varchar2(32)

Name: name Table: Gards_interval Description: Detector or system name. Format: varchar2(16)

Name: name Table: Gards_userenv Description: Variable name. Format: varchar2(40)

Name: net Table: Gards_roi_counts Description: Counts in ROI after processing. Format: number Units: counts

Name: net_err Table: Gards_roi_counts Description: Uncertainty of net. Format: number Units: counts

Database Schema

638 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: new_status Table: Gards_sample_status Description: sample_status after change Format: char(1)

Name: nid_confid Table: Gards_proc_params_template, Gards_sample_proc_params Description: User-configurable nuclide identifier confidence threshold. This threshold must be exceeded by the confidence level generated during analysis, or the nuclide is not considered identified. Format: number Range: nid_confid > 0.0

Name: nid_flag Table: Gards_nucl_ided, Gards_nucl_ided_orig, Gards_roi_concs Description: Flag, nuclide identification indicator. Format: number Range: nid_flag ∈ {–1, 0, 1, 2}

Name: nuclide_id Table: Gards_nucl_ided, Gards_nucl_ided_orig, Gards_nucl_lib, Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_nucl_lines_lib, Gards_xe_nucl_lib, Gards_xe_nucl_lines_lib Description: Nuclide identifier. Format: number Range: nuclide_id > 0

Database Schema

IDC-5.1.1Rev5 October 2002 639 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: nuclide_lib Table: Gards_proc_params_template, Gards_sample_proc_params Description: Indicator of which nuclide library data file is to be used when processing sample data. The actual data in this column is a UNIX path name to a nuclide library data file. Format: varchar2(96)

Name: nucl_name Table: Gards_comments, Gards_sample_cert_lines, Gards_qat_notify Description: Nuclide name. Format: varchar2(8)

Name: num_lines Table: Gards_nucl_lib, Gards_xe_nucl_lib Description: Total number of nuclide lines in library. Format: number

Name: num_samples Table: Gards_cat_template Description: Number of samples used to collect the average and define the standard deviation (RDC algorithm). Format: number

Name: num_value1 Table: Gards_trendvue Description: First plot value. Format: number

Database Schema

640 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: num_value2 Table: Gards_trendvue Description: Second plot value. Format: number

Name: num_value3 Table: Gards_trendvue Description: Third plot value. Format: number

Name: num_value4 Table: Gards_trendvue Description: Fourth plot value. Format: number

Name: old_status Table: Gards_status_history Description: sample_status before change Format: char(1)

Name: original_area Table: Gards_peaks, Gards_peaks_orig Description: Original peak area. Format: number Units: counts Range: original_area > 0

Database Schema

IDC-5.1.1Rev5 October 2002 641 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: original_uncer Table: Gards_peaks, Gards_peaks_orig Description: Uncertainty of original peak area. Format: number Units: counts

Name: owner Table: Gards_dbrole_owner Description: Name of database user who owns the database roles for the MAR tool. Format: varchar(12)

Name: param Table: Gards_soh_code Description: SOH parameter name. Format: varchar2(30)

Name: param_code Table: Gards_soh_char_data, Gards_soh_code, Gards_soh_num_data Description: SOH parameter code. Format: number

Name: param_display Table: Gards_soh_code Description: Text of the SOH parameter to be displayed in Trendvue. Format: varchar2(30)

Database Schema

642 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: param_display_flag Table: Gards_soh_code Description: Flag that indicates if the SOH parameter should appear in Trendvue’s menu; 1 = the parameter will appear in Trendvue’s menu, 0 = the parameter will not appear in Trendvue’s menu. Format: number

Name: pd_mod_flag Table: Gards_nucl_ided, Gards_nucl_ided_orig Description: Flag that indicates if a nuclide’s activity was modified by the parent/daughter calculation; 1 = the activity was modified, 0 = no modification. Format: number

Name: peak Table: Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig Description: Peak identifier associated with line. Format: number Range: peak > 0

Name: peak_end Table: Gards_proc_params_template, Gards_sample_proc_params Description: Spectrum energy at which the peak search terminates. Format: number Units: keV Range: peak_end > 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 643 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: peak_id Table: Gards_comments, Gards_peaks, Gards_peaks_orig Description: Unique peak identifier. Format: number Range: peak_id > 0

Name: peak_sense Table: Gards_proc_params_template, Gards_sample_proc_params Description: User-configurable threshold that aids in peak identification. This column is a multiplier of the digital filter. The smaller the peak_sense, the more likely a peak will be accepted. Format: number Range: peak_sense > 0.0

Name: peak_sig Table: Gards_peaks, Gards_peaks_orig Description: Peak significance; the peak area divided by lc. Format: number

Name: peak_start Table: Gards_proc_params_template, Gards_sample_proc_params Description: Spectrum energy at which the peak search begins. Format: number Units: keV Range: peak_start > 0.0

Database Schema

644 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: peak_tol Table: Gards_peaks, Gards_peaks_orig Description: Per peak energy tolerance; this approximates the energy tolerance at a given peak. Format: number

Name: permission_id Table: Gards_permissions, Gards_roles_permissions Description: Permission identifier. Format: number

Name: permission_name Table: Gards_permissions Description: String name of a permission. Format: varchar2(30)

Name: pocid Table: Gards_poc, Gards_receipt_log, Gards_stations Description: Unique point of contact identifier. Format: number Range: pocid > 0

Database Schema

IDC-5.1.1Rev5 October 2002 645 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: poll_time Table: Gards_qat_config Description: number of minutes rms_QAT sleeps between each database poll. Format: number

Name: pressure Table: Gards_environment Description: Outside air pressure. Format: number Units: millibars Range: pressure > 0.0

Name: pss Table: Gards_peaks, Gards_peaks_orig Description: Peak search significance. Format: number

Name: q_time Table: Gards_qat_config Description: number of minutes after gards_sample_status.review_date that rms_QAT_auto waits before releasing a sample Format: number

Name: quantity Table: Gards_sample_data Description: Air volume sampled. Format: number Units: m3

Database Schema

646 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: quantity Table: Gards_sample_cert Description: Total source activity. Format: number Units: Bq

Name: rated_efficiency Table: Gards_detectors Description: Efficiency of the detector relative to a standard 3 in. x 3 in. (7.62 cm x 7.62 cm) cylindrical NaI(Tl) detector at 1332 keV. The rated efficiency is usually supplied by the detector manufacturer. Format: number Range: 0 < rated_efficiency < 130

Name: rated_resolution Table: Gards_detectors Description: Rated resolution of the detector, supplied by the manufacturer, at 1332 keV. Format: number Range: 0.0 < rated_resolution < 3.0

Name: ratio_id Table: Gards_sample_ratios Description: Ratio identifier. Format: varchar2(15) Range: 1 ≤ ratio_id ≤ 6

Database Schema

IDC-5.1.1Rev5 October 2002 647 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: recipient_list Table: gards_qat_notify Description: comma-separated list of users to whom notification was sent Format: varchar2(128)

Name: ref_id Table: Gards_rlr Description: Sample reference identification. Format: varchar2(32)

Name: reference Table: Gards_aux_lines_lib Description: Reference for line properties. Format: varchar2(8)

Name: refpeak_energy Table: Gards_refline_master, Gards_update_reflines Description: Refline energy for a particular nuclide. Format: number Range: 0.0 < refpeak_energy

Name: report_mda Table: Gards_nucl_ided, Gards_nucl_ided_orig Description: Flag that indicates whether or not MDA is to be reported. Format: number Range: report_mda ∈ {–1, 0, 1}

Database Schema

648 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: rer_intercept Table: Gards_sample_update_params, Gards_update_params_template Description: Default RER intercept to be used during calculations. Format: number

Name: rer_slope Table: Gards_sample_update_params, Gards_update_params_template Description: Default RER slope to be used during calculations. Format: number

Name: res_energy Table: Gards_b_resolution_pairs, Gards_b_resolution_pairs_orig, Gards_resolution_pairs, Gards_resolution_pairs_orig Description: Resolution energy. Format: number Units: keV Range: 0.0 < res_energy

Name: res_error Table: Gards_b_resolution_pairs, Gards_b_resolution_pairs_orig, Gards_resolution_pairs, Gards_resolution_pairs_orig Description: Uncertainty of resolution. Format: number Units: keV Range: 0.0 < res_error

Database Schema

IDC-5.1.1Rev5 October 2002 649 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: resolution Table: Gards_b_resolution_pairs, Gards_b_resolution_pairs_orig, Gards_resolution_pairs, Gards_resolution_pairs_orig Description: Detector resolution. Format: number Units: keV

Name: result Table: Gards_sample_flags Description: Indicator for the database flag tests. 0 indicates failure, 1 indicates a pass. Format: number

Name: revid Table: Gards_fpe Description: Revision number of the FPEB. Format: number Range: revid ≥ 1

Name: review_date Table: Gards_sample_status Description: Date sample was last reviewed. Format: date

Database Schema

650 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: review_time Table: Gards_sample_status Description: Time duration of sample review. No longer automatically updated in Release 3. Format: number Units: minutes Range: review_time > 0

Name: right_fwhm_lim Table: Gards_proc_params_template, Gards_sample_proc_params Description: One of two user-configurable limits on the peak size. This column indicates the maximum possible peak width to the right of the peak centroid, expressed in multiples of the FWHM. Format: number Range: right_fwhm_lim > 0.0

Name: rlr_id Table: Gards_rlr Description: Unique radionuclide lab report identifier. Format: number

Name: rms_id Table: Gards_data_log, Gards_processing_errors Description: Internal identifier for message; either the sample_id for PHDs, the rlr_id for RLRs, or the soh_id for SOHs. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 651 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: roi Table: Gards_bg_efficiency_pairs, Gards_roi_channels, Gards_roi_concs, Gards_roi_counts, Gards_roi_lib, Gards_roi_limits, Gards_sample_xe_proc_params, Gards_xe_proc_params_template Description: Unique ROI identifier. Format: number

Name: role_id Table: Gards_dist_sample_queue, Gards_roles, Gards_roles_permissions, Gards_users_roles Description: Role identifier. Format: number

Name: role_name Table: Gards_roles Description: String name of a role. Format: varchar2(30)

Name: rqst_id Table: Gards_query_results Description: Unique query identifier. Format: number Range: rqst_id > 0

Name: rqst_string Table: Gards_query_results Description: Data requested by a client using the IDC Event Screening Tool. Format: varchar2(100)

Database Schema

652 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: sample_diameter Table: Gards_sample_aux Description: Diameter of gas chamber. Format: number Units: cm

Name: sample_height Table: Gards_sample_aux Description: Height of the sample. Format: number Units: cm Range: sample_height > 0.0

Name: sample_id Table: Gards_auto_sample_cat, Gards_bg_efficiency_pairs, Gards_bg_energy_cal, Gards_b_energy_pairs, Gards_b_energy_pairs_orig, Gards_b_resolution_pairs, Gards_b_resolution_pairs_orig, Gards_comments, Gards_dist_sample_queue, Gards_efficiency_cal, Gards_efficiency_pairs, Gards_energy_cal, Gards_energy_cal_orig, Gards_energy_pairs, Gards_energy_pairs_orig, Gards_environment, Gards_fpe, Gards_histogram, Gards_nucl_ided, Gards_nucl_ided_orig, Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_peaks, Gards_peaks_orig, Gards_qat_notify, Gards_qchistory, Gards_resolution_cal, Gards_resolution_cal_orig, Gards_resolution_pairs, Gards_resolution_pairs_orig, Gards_roi_channels, Gards_roi_concs, Gards_roi_counts, Gards_roi_limits, Gards_sample_aux, Gards_sample_cat, Gards_sample_cert, Gards_sample_cert_lines, Gards_sample_data, Gards_sample_description, Gards_sample_flags, Gards_sample_proc_params, Gards_sample_ratios, Gards_sample_status, Gards_sample_update_params, Gards_sample_xe_proc_params, Gards_spectrum, Gards_status_history, Gards_total_effic, Gards_user_comments Description: Sample identifier. Format: number Range: sample_id > 0

Database Schema

IDC-5.1.1Rev5 October 2002 653 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: sample_ref_id Table: Gards_sample_aux, Gards_processing_errors Description: Sample reference identifier (SRID). Format: varchar2(32)

Name: sample_status Table: Gards_qat_query_filter Description: comma-separated list of sample status values Format: varchar2(128)

Name: sample_type Table: Gards_mdas2report, Gards_proc_params_template, Gards_relevant_nuclides, Gards_sample_data, Gards_spectrum Description: Sample type indicator: P for particulate, G for gamma spectroscopy gas, B for beta-gamma coincidence gas. Format: char(1) varchar2(2) for gards_mdas2report Range: sample_type ∈ {B, G, P}

Name: score Table: Gards_energy_cal, Gards_energy_cal_orig Description: The score used when comparing this ECR to other ECRs; a measure of both the ape and the determinant. Format: number

Database Schema

654 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: sdmult Table: Gards_qcparams Description: Standard deviation multiplier for the K-40 location test. This column value is usually equal to 3 standard deviations. Format: number NA Value: –999.0 Range: sdmult = 3

Name: sensor_name Table: Gards_soh_sensor_data Description: Unique sensor name to distinguish between sensors of the same type. Format: varchar2(20)

Name: sensor_type Table: Gards_soh_sensor_data Description: Type of sensor (TEMP, PRESSURE, PROCESSFLOW, VOLTAGE, COUN- TRATES, DEWPOINT, CO2VOLUME). Format: varchar2(20)

Name: session_id Table: Gards_trendvue Description: Unique identifier assigned to a Trendvue session. Format: number Range: 0 < session_id

Name: site_det_code Table: Gards_sample_data Description: Station code concatenated with detector code. Format: char(15)

Database Schema

IDC-5.1.1Rev5 October 2002 655 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: soh_id Table: Gards_soh_header Description: SOH identifier. Format: number

Name: spectral_qualifier Table: Gards_proc_params_template, Gards_refline_master, Gards_sample_data, Gards_update_reflines Description: Time for which sample was exposed: FULL or PREL (preliminary). Format: varchar2(5)

Name: squant_err Table: Gards_proc_params_template, Gards_sample_proc_params Description: Uncertainty in the air volume of a sample. This value is used to determine the uncertainty in the activity concentration. (No longer used in Release 3 processing.) Format: number Units: m3 Range: squant_err > 0

Name: start_time Table: Gards_interval, Gards_met_data Description: Date of data sampling commencement. Format: date float for gards_interval

Database Schema

656 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: state Table: Gards_qchistory, Gards_interval Description: Text results of quality control hypothesis test (gards_qchistory). Specific activity of detector or system (gards_interval). Format: varchar2(128) varchar2(16) for gards_interval

Name: station_code Table: Gards_alerts, Gards_processing_errors, Gards_stations Description: Station code. Format: varchar2(5) char(5) for gards_alerts

Name: station_id Table: Gards_alerts, Gards_cat_template, Gards_data_log, Gards_met_data, Gards_nucl_ided, Gards_nucl_ided_orig, Gards_nucl_lines_ided, Gards_nucl_lines_ided_orig, Gards_proc_params_template, Gards_qchistory, Gards_qctargets, Gards_rlr, Gards_sample_data, Gards_soh_char_data, Gards_soh_header, Gards_soh_num_data, Gards_soh_sensor_data, Gards_stadet, Gards_stations, Gards_stations_schedule, Gards_station_assignments, Gards_update_reflines Description: Unique station identifier. Format: number Range: station_id > 0

Database Schema

IDC-5.1.1Rev5 October 2002 657 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: station_list Table: Gards_qat_query_filter Description: comma-separated list of stations Format: varchar2(1024)

Name: status Table: Gards_data_log Description: Status of data msg_id processing; P - processed or U - unprocessed. Format: char(1) Range: status ∈ {P, U}

Name: status Table: Gards_detectors Description: Status of detector: if Y, then data from this detector are automatically processed; if N, then they are not processed automatically. Format: varchar2(2) Range: status ∈ {N, Y}

Name: status Table: Gards_stations Description: Status of station: if NULL, then station is fully operational, otherwise status is I. Format: varchar2(2) Range: status ∈ {I}

Database Schema

658 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: status Table: Gards_sample_status Description: Current processing status of sample. Some possible values are: A - analyzed, P - processed, R - reviewed, U - unprocessed, V - viewed. Format: char(1) Range: status ∈ {A, P, R, U, V}

Name: t_time Table: gards_qat_config Description: number of minutes after gards_sample_status.entry_date that rms_QAT_auto waits before releasing a sample. Format: number

Name: telephone Table: Gards_poc Description: Telephone number of the point of contact. Format: varchar2(20)

Name: temperature Table: Gards_environment Description: Outside temperature. Format: number Units: degrees C

Name: temporal_unit Table: Gards_stations_schedule Description: Units for schedule period - currently only the value DAYS is supported. Format: char(5)

Database Schema

IDC-5.1.1Rev5 October 2002 659 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: temporal_value Table: Gards_stations_schedule Description: Expected station schedule period. Format: number

Name: test Table: Gards_flags Description: Calculated result of the test; this value is compared to the threshold value. (examples are <, =, >, >=). Format: varchar2(8)

Name: test_code Table: Gards_cat_criteria_tests Description: unique test code identifier string Format: varchar2(24)

Name: test_date Table: Gards_rlr Description: Test completion date at lab. Format: date

Database Schema

660 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: test_id Table: Gards_cat_criteria_tests Description: unique identifier Format: number

Name: test_name Table: Gards_cat_criteria_tests Description: test name label for display Format: varchar2(48)

Name: threshold Table: Gards_flags Description: Threshold against which the results in the test column are compared. Format: number

Name: total_rainfall Table: Gards_met_data Description: Total rainfall. Format: number Units: millimeters Range: 0.0 ≤ total_rainfall

Name: transmit_date Table: Gards_rlr Description: Transmit date. Format: date

Database Schema

IDC-5.1.1Rev5 October 2002 661 Name: transmit_dtg Table: Gards_sample_data, Gards_soh_header Description: Date of sample data message transmittal. Format: date

Name: tstat Table: Gards_cat_template, Gards_energy_cal, Gards_energy_cal_orig Description: T-statistic confidence level (gards_energy_cal, gards_energy_cal_orig). Multiplier applied to variance estimate for defining prediction interval (gards_nic_init). Format: number Range: tstat > 0.0

Name: type Table: Gards_codes Description: Category of code. Format: varchar2(15)

Name: type Table: Gards_detectors, Gards_stations Description: Brief description of detector or station. Format: varchar2(6) Range: ASCII characters IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: type Table: Gards_mdas2report, Gards_nucl_ided, Gards_nucl_ided_orig, Gards_nucl_lib, Gards_relevant_nuclides, Gards_xe_nucl_lib Description: Nuclide type. Choices are: ACTIVATION, COSMIC, FISSION(G), FIS- SION(P), or NATURAL. Format: varchar2(16) Range: type ∈ {ACTIVATION, COSMIC, FISSION(G), FISSION(P), NATURAL}

Name: type Table: Gards_receipt_log Description: Data type of message. Format: varchar2(5)

Name: unit Table: Gards_soh_code Description: Unit in which the SOH parameter is stored. Format: varchar2(32)

Name: units Table: Gards_cat_criteria_tests, Gards_flags, Description: Unit values for the test bounds; Units of the event screening test. Format: varchar2(16)

Name: upper_bound Table: Gards_auto_sample_cat, Gards_cat_template, Gards_sample_cat Description: Upper limit of the amount of a nuclide that can be acceptably found. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 663 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: upper_limit Table: Gards_cat_criteria_tests Description: upper limit bound of the test Format: number

Name: upper_roi_number Table: Gards_sample_ratios Description: ROI number associated with the upper ROI. Format: number Range: 1 ≤ upper_roi_number ≤ 6

Name: use_mult Table: Gards_sample_update_params, Gards_update_params_template Description: Flag for using multiplets in determining matches. A value of 0 indicates not to use multiplets; 1 indicates the use of multiplets. Format: number Range: use_mult ∈ {0,1}

Name: use_review_cat Table: Gards_qat_query_filter Description: flag for reviewed or auto categorization Format: number

Name: use_weight Table: Gards_sample_update_params, Gards_update_params_template Description: Flag for controlling of weights in ECR updating. A value of 0 indicates not to use weights; 1 indicates the use of weights. Format: number Range: 0 ≤ use_weight ≤ 1

Database Schema

664 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: user Table: Gards_status_history Description: user making status change Format: varchar2(30)

Name: user_id Table: Gards_dist_sample_queue, Gards_qat_query_filter, Gards_station_assignments, Gards_users, Gards_users_roles Description: User identifier. Format: number

Name: user_name Table: Gards_users Description: String name for a user database login name. Format: varchar2(30)

Name: value Table: Gards_sample_flags Description: Threshold value for the test. Format: number

Name: value Table: Gards_soh_char_data, Gards_soh_num_data, Gards_soh_sensor_data Description: Value of the specified SOH parameter. Format: number

Database Schema

IDC-5.1.1Rev5 October 2002 665 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Name: value Table: Gards_userenv Description: Variable name. Format: varchar2(256)

Name: width Table: Gards_peaks, Gards_peaks_orig Description: Width of peaks (channels). Format: number Range: width > 0

Name: width_adj Table: Gards_qcparams Description: Peak width standard deviation inflation factor. Format: number

Name: xe_collect_yield Table: Gards_sample_aux Description: Xe collection yield of the system; volume of stable Xe on detector/volume of stable Xe collected on first trap. Format: number

Name: xe_collect_yield_err Table: Gards_sample_aux Description: Uncertainty of xe_collect_yield. Format: number

Database Schema

666 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides Chapter 7:

Radionuclide Column Descriptions ▼

Name: xe_volume Table: Gards_sample_aux Description: Volume of stable Xe in gas cell counter. Format: number Units: cm3

Name: xe_volume_err Table: Gards_sample_aux Description: Uncertainty of xe_volume. Format: number Units: cm3

Name: xform Table: Gards_cat_template Description: Code for transform function applied to measurement data (1 = log, 2 = square root, 3 = none). Format: number Range: xform ≥ 0.0

Name: zeroshift Table: Gards_sample_update_params, Gards_update_params_template Description: Change in channel number at 0 keV between one spectrum and the previous spectrum. Format: number Range: zeroshift ≥ 0.0

Database Schema

IDC-5.1.1Rev5 October 2002 667 IDC DOCUMENTATION Chapter 7: User Guides

▼ Radionuclide Column Descriptions

Database Schema

668 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

References

The following sources supplement or are referenced in document:

[And90a] Anderson, J., Farrell, W., Garcia, K., Given, J., and Swanger, H., CSS Version 3 Database: Schema Reference Manual, Science Applications International Corporation, 1990.

[Car97] Carter, J., and Bowman, J. R., IDC Database Schema, CMR-97/28, 1997.

[Fli74] Flinn, E. A., Engdhal, E. R., and Hill, A. R., “Seismic and Geographical Regionalization,” Bulletin of the Seismological Society of America, Volume 64, No. 3, Part ii, pp. 771-992, 1974.

[Gan79] Gane, C., and Sarson, T., Structured Systems Analysis: Tools and Techniques, Prentice-Hall, Inc., Englewood Cliffs, NJ, 1979.

[IDC5.1.1] Science Applications International Corporation, Pacific-Sierra Research, Inc., Database Schema (Part 1 and Part 2), SAIC-98/3009, PSR-98/TN1127, 1998.

[IDC5.1.1Rev1] Science Applications International Corporation, Pacific-Sierra Research Corporation, Database Schema (Parts 1, 2, and 3), Revision 1, SAIC-99/3009, PSR-99/TN1142, 1999.

[IDC5.1.1Rev5] Science Applications International Corporation, Veridian Systems, Database Schema, (Part 1, Part 2, and Part 3), Revision 5, TN2924, October 2002.

[IDC5.1.2] Science Applications International Corporation, Pacific-Sierra Research Corporation, Database Tutorial, SAIC-99/3022, PSR-99/TN1145, 1999.

Database Schema

IDC-5.1.1Rev5 October 2002 R669 IDC DOCUMENTATION User Guides

▼ References

[IDC5.1.3Rev0.1] Science Applications International Corporation, Veridian Pacific- Sierra Research, Configuration of PIDC Databases, Revision 0.1, SAIC-01/3022, PSR-99/TN1114, 2001.

[IDC7.1.1] Science Applications International Corporation, Detection and Feature Extraction (DFX)–Scheme Files, SAIC-01/3000, 2001.

[IDC7.1.3] Science Applications International Corporation, Surface Wave Identification and Measurement, SAIC-01/3008, 2001.

[IDC7.1.4] Science Applications International Corporation, Global Association (GA) Subsystem, SAIC-01/3009, 2001.

[IDC7.1.5] Science Applications International Corporation, Event Location Software, SAIC-01/3010, 2001.

[IDC7.1.6] Science Applications International Corporation, Event Magnitude Software, SAIC-01/3011, 2001.

[IDC7.1.10Rev3] Veridian Systems, Radionuclide Software Design, Revision 3, TN2927, October 2002.

[IDC7.1.11] Science Applications International Corporation, WaveExpert, SAIC- 00/3029, 2000.

[IDC7.1.12] Science Applications International Corporation, Station Processing (StaPro), SAIC-00/3013, 2000.

[IDC7.3.1] Science Applications International Corporation, Distributed Application Control System (DACS), SAIC-01/3001, 2001.

[IDC7.4.1] Science Applications International Corporation, Continuous Data Subsystem CD–1.1, SAIC-01/3012, 2001.

[IDC7.4.2] Science Applications International Corporation, Pacific-Sierra Research Corporation, Message Subsystem, SAIC-98/3003, 1998.

[IDC7.4.3] Science Applications International Corporation, Retrieve Subsystem, SAIC-01/3024, 2001.

[IDC7.4.4] Science Applications International Corporation, Subscription Subsystem, SAIC-98/3001, 1998.

Database Schema

R670 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

References ▼

[IDC7.5.1] Science Applications International Corporation, Archiving Subsystem, SAIC-01/3013, 2001.

[Swa91] Swanger, H., Given, J., and Anderson, J., IMS Extensions to the Center Version 3 Database, Science Applications International Corporation, SAIC-91/1138, 1991.

[Swa93] Swanger, H., Anderson, J., Sereno, T., Given, J., and Williams, D., Extensions to the Center Version 3 Database, Revision 1, Science Applications International Corporation, SAIC-93/1123, 1993.

Database Schema

IDC-5.1.1Rev5 October 2002 R671

IDC DOCUMENTATION User Guides

Glossary A

abundance R: Fraction of a decay event that results in the radiation(s) or interest (for example, a gamma line at a specific energy or a beta- Selected definitions in this glossary include gamma coincidence pair). Intensity is prefixes of either “R: ” or sometimes used to mean abundance. “S/H/I: .” Definitions applicable only to the radionuclide technology include the “R: ” activation products prefix; definitions applicable only to seis- R: Nuclides produced from the absorption mic, hydroacoustic, or infrasonic technolo- of a neutron by a nucleus. gies include the “S/H/I: ” prefix. activity R: Decay rate of a radionuclide; usually Symbols expressed in Becquerels (disintegrations per second), Bq. 2-D Two-dimensional. amp Amplitude. 3-C Three-component. amplitude S/H/I: Zero-to-peak height of a waveform β in nanometers. R: Beta particle. array γ S/H/I: Collection of sensors distributed R: Gamma particle. over a finite area (usually in a cross or con- centric pattern) and referred to as a single µBq station. R: MicroBecquerels. arrival µPa S/H/I: Signal that has been associated to an event. First, the Global Association (GA) MicroPascals. software associates the signal to an event.

Database Schema

IDC-5.1.1Rev5 October 2002 G673 IDC DOCUMENTATION User Guides

▼ Glossary

Later during interactive processing, many beta particle arrivals are confirmed and improved by R: Electron that is produced from a nuclear visual inspection. decay. May also refer to other electron radiations, for example, a conversion electron. ASCII American Standard Code for Information blank subtraction Interchange. Standard, unformatted 256- R: Process of removing counts from a sam- character set of letters and numbers. ple spectrum or a region of interest within a sample spectrum originating from the air attribute filter. (1) A database column. S/H/I: (2) Charac- teristic of an item; specifically, a quantita- BLANKPHD tive measure of a S/H/I arrival such as R: Blank Pulse Height Data; ASCII data azimuth, slowness, period, and amplitude. message containing the pulse height data of an unexposed air filter, as well as other authentication signature information, in an IDC-approved format. Series of bytes that are unique to a set of data and that are used to verify the authen- ticity of the data. C

CALIBPHD B R: Calibration Pulse Height Data; ASCII data message containing the pulse height background data of a certified standard source, as well R: Contribution to a spectrum from natu- as other information, in an IDC-approved rally occurring radionuclides as well as format. The data in a CALIBPHD are used interactions between radiation and materi- to determine the ECR, EER, and RER. als in the vicinity of the detector. calibration coefficients baseline R: Numbers that define the energy, resolu- R: Contribution to a spectrum from the par- tion, and efficiency equations. tial energy deposition of a gamma-ray in a detector. centroid R: Energy (in keV) or channel number at beta-gamma coincidence event the center of a fitted peak. R: Nuclear decay that produces both a gamma ray and a beta particle within a very channel short time scale. May also refer to other R: Energy window (in keV) representing a photon-electron coincidence events such as differential increment of pulse height. an X-ray with a conversion electron. S/H/I: Component of motion or distinct stream of data.

Database Schema

G674 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

Glossary ▼

cm dB Centimeter. Decibel.

coherent defining S/H/I: Quality of having a fixed phase rela- S/H/I: Arrival attribute, such as arrival tionship; as signals from a wavefront time, azimuth, or slowness, which is used detected on numerous seismic or infrasonic in calculating the event’s location or magni- array station elements. tude.

concentration defining phase R: Activity per unit volume of air. S/H/I: Associated phase for which features are used in the estimation of the location cosmogenic nuclides and origin time of an S/H/I event. R: Nuclides produced by the interaction of cosmic-rays with matter. DETBKPHD R: Detector Background Pulse Height Data; counts ASCII data message containing the pulse R: Number of pulses observed within a height data from a background count, as spectrum channel. well as other information, in an IDC- S/H/I: Units of digital waveform data. approved format.

critical level/limit detection limit R: Minimum net counts that must be con- R: The smallest amount of activity that can tained in an ROI for nuclide identification be reliably detected and quantified in a spectrum. This quantity is used to deter- (Lc). mine the MDC. CSCI Computer Software Configuration Item. E CTBT ECR Comprehensive Nuclear Test-Ban Treaty R: Energy versus Channel Regression; an (the Treaty). equation providing the initial detector-specific relationship between channel number D and energy. The equation contains calibration coefficients and is estimated from a transmitted calibration dataset. DB Database.

Database Schema

IDC-5.1.1Rev5 October 2002 G675 IDC DOCUMENTATION User Guides

▼ Glossary

ECRU F R: Energy versus Channel Regression Update; an equation providing the final FFT detector-specific relationship between Fast Fourier Transform. channel number and energy. fission (P) EER R: Particulates created in a fission event. R: Efficiency versus Energy Regression; an equation providing the detector-specific fission (G) relationship between efficiency and energy. R: Gases created in a fission event. energy f-k R: Usually refers to the measured kinetic S/H/I: Frequency versus wavenumber (k) energy of radiation quanta deposited in a analysis that maps phase power from an detector. The unit most appropriate for such array as a function of azimuth and slow- measurements is keV. ness. S/H/I: Occurrence that displays characteristics indicative of a possible nuclear weap- FPID ons test. R: Fission Product Identification. epoch time FTP Number of seconds after January 1, 1970 00:00:00.0. File Transfer Protocol; protocol for trans- ferring files between computers. event FULL SPHD R: Occurrence that displays characteristics indicative of a possible nuclear weapons R: Full Sample Pulse Height Data; ASCII test. data message containing the pulse height S/H/I: Unique source of seismic, hydroa- data of a sample acquired for a complete coustic, or infrasonic wave energy that is collection interval, as well as other infor- limited in both time and space. mation, in an IDC-approved format.

EWMA FWHM R: Exponentially Weighted Moving Aver- R: Full Width at Half-Maximum; metric of age; statistical filter that recursively gener- detector resolution and equivalent to the ates a prediction interval using past width of a photopeak (in keV) taken at the observations weighted in an exponential peak height equal to half the maximum fashion. This filter is useful for determining peak counts. anomalous radionuclide concentrations for categorization purposes.

Database Schema

G676 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

Glossary ▼

G H

g hydroacoustic Gram. S/H/I: Pertaining to sound in the ocean.

GA S/H/I: Global Association application. GA I associates S/H/I phases to events. IDC gamma International Data Centre. R: Gamma-ray. IEEE gamma ray Institute for Electrical and Electronic Engi- R: Photon that is produced from a nuclear neers. transition; may also imply other photon radiations, for example, an X-ray. IIR Infinite Impulse Response (filters also GARDS referred to as recursive filters). R: Global Atmospheric Radionuclide Detection System; the network of radionu- IMS clide monitoring stations that meet CTBT International Monitoring System. requirements and transmit radionuclide data to the IDC with coordination by the infrasonic IDC. S/H/I: Pertaining to low-frequency (sub- audible) sound in the atmosphere. GASBKPHD R: Gas Background Pulse Height Data. Internet Data type sent by noble gas monitoring sys- World-wide network of computers linked tems that observe a memory effect during by means of the IP protocol. sample acquisition due to atoms from the previous sample adsorbed onto the walls of IP the gas cell. The counts from the memory Internet protocol. effect must be subtracted from the sample counts for accurate activity quantification.

GMT K Greenwich Mean Time. KB

GSETT-3 Kilobyte. 1,024 bytes. S/H/I: Group of Scientific Experts Third Technical Test.

Database Schema

IDC-5.1.1Rev5 October 2002 G677 IDC DOCUMENTATION User Guides

▼ Glossary

keV MDA R: Kiloelectron Volts; a metric of kinetic R: Minimum Detectable Activity. energy. MDC keyline R: Minimum Detectable Concentration. R: Photon with the highest detection probability. minimum detectable concentration R: Activity concentration of a given radionuclide that is indistinguishable from the L measurement process noise level.

L c ML R: Critical level. S/H/I: Magnitude based on waves measured near the source. local S/H/I: (1) (distance) Source to seismometer mm separations of a few degrees or less. (2) Millimeter. (event) Recorded at distances where the first P and S waves from shallow events have trav- monitoring system eled along direct paths within the crust. See IMS and RMS.

M Ms S/H/I: Magnitude of seismic surface waves. m msmle (1) Meter(s). (2) Megabyte(s); 1,024 kilobytes. (3) Month(s). (4) Minute(s). S/H/I: Magnitude of an event based on maximum likelihood estimation using surface waves. mb S/H/I: Magnitude of a seismic body wave. multiplet

mbar R: Spectral region of interest comprised of more than one photopeak. Millibar.

mbmle N S/H/I: Magnitude of an event based on maximum likelihood estimation using seis- NA mic body waves. Not Applicable. mBq R: MilliBecquerel.

Database Schema

G678 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

Glossary ▼

NDC ORACLE National Data Center. Vendor of PIDC and IDC database management system. NID Nuclide Identification. origin S/H/I: Hypothesized time and location of a nm seismic, hydroacoustic, or infrasonic event. Nanometer. Any event may have many origins. Charac- teristics such as magnitudes and error esti- nondefining mates may be associated with an origin. S/H/I: Arrival attribute, such as arrival time, azimuth, or slowness, which is associ- P ated, but not used in calculating the event’s location or magnitude. parameter (par) file nondefining phase ASCII file containing values for parameters of a program. Par files are used to replace S/H/I: Associated phase for which features command line arguments. The files are for- are not used in the estimating the location matted as a list of [token = value] and origin time of an S/H/I event. strings. NSE peak Noise Spectrum Equalization. R: Statistically significant increase in counts above a spectrum baseline at an nuclide energy associated with a gamma line of a R: One of many combinations of nucleons particular radionuclide or other phenome- that may comprise an atomic nucleus. non. Because all nuclides of interest with respect to CTBT compliance verification are radio- PHD active, this term is often used to refer spe- R: Pulse Height Data; a format for spectral cifically to radionuclides. data messages. Possible PHD data message types include BLANKPHD, CALIBPHD, O DETBKPHD, GASBKPHD, QCPHD, and SAMPLEPHD. Operations Manuals PIDC Treaty-specified, formal documents that Prototype International Data Centre. describe how to provide data, receive IDC products, access the IDC database, and evaluate the performance of the IDC.

Database Schema

IDC-5.1.1Rev5 October 2002 G679 IDC DOCUMENTATION User Guides

▼ Glossary

polarization R S/H/I: Form of three-component analysis used to derive azimuth and slowness infor- R mation from non-array stations. R: Radionuclide.

PREL SPHD radioactivity R: Preliminary Sample Pulse Height Data; R: See activity. ASCII data message containing the pulse height data of a sample acquired for less radionuclide than a complete collection interval, as well R: Nuclide that has an unstable nucleus, as other information. that is, a radioactive nuclide. primary seismic REB S/H/I: IMS seismic station(s) or data that is S/H/I: Reviewed Event Bulletin; the bulle- (are) part of the detection network. tin formed of all S/H/I events that have passed analyst inspection and quality assur- PS ance review. R: Peak Search. region of interest Q R: Region of a radionuclide spectrum or histogram that corresponds to a particular radionuclide. QC Quality Control. regional S/H/I: (1) (distance) Source to seismometer QCPHD separations between a few degrees and 20 R: Quality Control Pulse Height Data; degrees. (2) (event) Recorded at distances ASCII data message containing the pulse where the first P and S waves from shallow height data of a certified source as well as events have traveled along paths through other information. Information in the the uppermost mantle. QCPHD, along with other data, is used to check a detector’s state of health. RER R: Resolution (versus) Energy Regression; quefrency an equation providing the initial detector- S/H/I: Time-delay axis with units of sec- specific relationship between resolution onds for a cepstrum. and energy. This equation contains calibration coefficients and is interpolated from a transmitted calibration spectrum.

Database Schema

G680 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

Glossary ▼

residual S S/H/I: Difference in time, azimuth, or slowness between a calculated attribute and its SAIC corresponding theoretical value. Science Applications International Corpo- ration. RLR R: Radionuclide Lab Report; report con- sample taining sample analysis results from a certi- Any physical entity counted on a detector. fied radionuclide laboratory. SAMPLEPHD RMS R: Sample Pulse Height Data; ASCII data R: Radionuclide Monitoring System; the message containing pulse height data part of the IMS that monitors the atmo- acquired by counting a gas or particulate sphere for radionuclides. sample with a detector system.

RNPS S/H/I R: Radionuclide Network Product Sum- S/H/I: Seismic, hydroacoustic, and infra- mary; daily report containing a summary of sonic. the Radionuclide Network for a three-day period, including the data received, their SID products, and any relevant nuclides. R: Sample ID; unique alphanumeric string assigned to a sample during the automated ROI processing for identification and account- R: Region of interest. ing purposes.

RRR singlet R: Reviewed Radionuclide Report. Elec- R: Spectrum photopeak consisting of tronic file containing the final results of the counts from one mono-energetic gamma- interactive review of the automated radio- ray; photopeak containing counts from nuclide processing. It contains sections on multiple photons, but fit as if it is com- sample information, measurement categori- prised of counts from only one because zation, measured radionuclide quantities, contributions from the individual radiations MDCs, radionuclide identification, analyst cannot be separated, as in a multiplet. editing, processing parameters, data quality flags, event screening flags, calibration SLSD equations, and field of regard. S/H/I: Standard List of Signal Detections.

SOH State of Health; indicator of a system’s operability.

Database Schema

IDC-5.1.1Rev5 October 2002 G681 IDC DOCUMENTATION User Guides

▼ Glossary

spectrum Sum/Natural R: Plot of the differential number of pulses R: Artificial entries in the nuclide library (in counts) per differential pulse height (in that enable the automated processing to channels or keV). identify commonly observed sum peaks in S/H/I: Plot of the energy contained in a spectrum. waveforms as a function of frequency.

SPHD T R: Sample Pulse Height Data; ASCII data message type containing the pulse height taxonomy data of a sample, as well as other informa- Systematic arrangement; classification. tion. The two types of SPHDs are full and preliminary. See FULL SPHD and PREL TCP/IP SPHD. Transmission Control Protocol/Internet Protocol. SQL Structured Query Language; a language for teleseismic manipulating data in a relational database. S/H/I: (1) (distance) Source to seismometer separations of 20 degrees or more. (2) SSREB (event) Recorded at distances where the first R: Standard Screened Radionuclide Event P and S waves from shallow events have trav- Bulletin; bulletin generated by the IDC eled paths through the mantle/core. when fission or activation products are detected at a radionuclide station above time series normal limits. A SSREB contains informa- S/H/I: Time ordered sequence of data sam- tion on the possible event, source location, ples. Typically a waveform or derived from fission products, activation products waveforms, such as a beam. detected, any isotopic ratios calculated, and any certified laboratory results. New event Treaty information can be added to the SSREB as Comprehensive Nuclear Test-Ban Treaty it arrives, therefore, multiple revisions of an (CTBT). SSREB are possible. Type I Error STA/LTA R: Spectral region of interest falsely identi- S/H/I: Short-term average/long-term aver- fied as a peak by the automated processing. age ratio. Type II Error R: Peak undetected by the automated processing.

Database Schema

G682 October 2002 IDC-5.1.1Rev5 IDC DOCUMENTATION User Guides

Glossary ▼

Database Schema

IDC-5.1.1Rev5 October 2002 G683