Smoothdome™ Slotted Cap Skullgard® Protective Caps and Hats

MSA Products for Construction

SmoothDome™ Slotted Cap

SmoothDome Cap Assemblies 4-Point Fas-Trac 6-Point Fas-Trac Color (Standard Size) (Standard Size) White 10074067 10084078 Blue 10074068 10084079

SmoothDome Protective Cap Yellow 10074069 10084080 Orange 10074070 10084081 MSA's SmoothDome Slotted Caps are welcomed by welders, especially those in shipbuilding and general construction, for its smooth crown Red 10074071 10084082 and light weight. These caps meet allapplicable requirements for a Type Green 10074072 10084083 I (top impact) helmet as outlined in ANSI/ISEA Z89.1-2009 (Class E) and Gray 10074073 10084084 CSA Z94.1-2005 (Class E). Hi-Viz Orange* 10074077 10084088 SmoothDome Caps also meet the ANSI/ISEA Z89.1-2009 voluntary standard for low temperature [LT] and reverse donning. Look for the Hi-Viz Yellow-Green* 10074084 10084095 official reverse donning logo to determine if your hard hat may Hi-Viz Orange w/Yellow-Green Stripe* 10095987 10095988 be worn backwards without voiding approvals. Hi-Viz Yellow-Green w/Orange Stripe* 10095989 10095990 Replacement Suspension Hi-Viz Orange w/Silver Stripe* 10096141 • 4-Point Fas-Trac 6-Point Fas-Trac Swing-Ratchet Hi-Viz Yellow-Green w/Silver Stripe* 10096142 • Suspension Suspension Suspension * SmoothDome Cap meets the voluntary standard for hi-visibility as prescribed by ANSI/ISEA Z89.1-2009. 10087220 10092163 816645 Look for the official hi-visibility marking [HV] on the helmet's ANSI label. Skullgard® Protective Caps and Hats

Third-party certified by: Skullgard Assemblies Skullgard Cap Skullgard Hat w/Staz-On w/Fas-Trac w/Swing-Ratchet w/Staz-On w/Fas-Trac Natural Tan 454617 475395 816651 454664 475407 White 454618 475396 • 454665 475408 Yellow 454619 475397 • 454666 • Red 454620 • • • • Green 454621 • • 454668 • Grey 454622 • • • • Skullgard Protective Cap Blue 454623 • • • • Orange 454626 • • 454673 • Hi-Viz Red-Orange* 458702 • • • • Skullgard with * Skullgard Cap meets the voluntary standard for hi-visibility as prescribed by ANSI/ISEA Z89.1-2009. Swing-Ratchet Look for the official hi-visibility marking [HV] on the helmet's ANSI label. Suspension Alternative Skullgard Assemblies Large Skullgard Cap with Staz-On suspension, natural tan 82018 Large Skullgard Cap with Fas-Trac suspension, natural tan 475405 Standard Skullgard Cap with Staz-On suspension, lamp bracket and cord holder, natural tan 460409 Skullgard Hat with Staz-On suspension, lamp bracket and cord holder, natural tan 460389 Skullgard Protective Hat Skullgard Cap with Fas-Trac suspension, welder’s lugs, natural tan 482002

Skullgard Caps and Hats meet all applicable requirements for a Type I (top impact) helmet as outlined in ANSI/ISEA Replacement Suspensions Z89.1-2009 (Class G). These caps and hats also meet the Size Staz-On Fas-Trac Swing-Ratchet 1-Touch

ANSI/ISEA Z89.1-2009 voluntary standard for low 1 1 5 Std (6 /2–8) 454231 473334 816654 (6 /2–7 /8) 10061128 temperature [LT]. 1 Large (7–8 /2) 468096 478454 • •

8 Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com HELMET LIGHTS FROM MSA Bright | Durable | Lightweight | Non-incendive

Ordering Information

Stealthlite® Helmet Light VersaLite* Helmet Light P/N 697261 P/N 697259 10,000 candlepower Xenon lamp module 6,000 candlepower Xenon lamp module One-hand safety switch operation and black lanyard Multi-position swivel head Burn time using 4AA alkaline battery cells: 5–6 hours 2AA alkaline battery cells (included) Watertight to 500 feet Burn time: 5–6 hours High-impact polycarbonate case Water resistant, high-impact polycarbonate case Color: non-glare black Color: non-glare black Length: 6 ½” Length: 3”

Diameter: 1 5⁄8” Width: 1 ¾”

Height: 1 7⁄8” * Trademark of Pelican Products, Inc.

The MSA light holder is designed especially to fit MSA slotted hard hats. The holder allows the light to be pointed downward at an angle, so the the light beam follows the natural line of sight. When properly attached, the holder will not affect the dielectric properties of the helmet. Light Holder Light Holder P/N 814322 Non-metallic MSA light holder for slotted caps Intrinsically safe helmet lights, 5 both of which are FM and CSA-approved

Approvals Typical Hazardous Locations The Stealthlite and VersaBrite are FM These locations are not exhaustive approved for Class I, Division 2, Groups A, B, and are listed for your convenience. C, D and CSA approved for Class I, Division 2, A supervisor should always be consulted Groups A, B, C, D and Class II, Division 2, before using any MSA light to determine Group G. if it is appropriate to use the light in a particular application. This means that MSA Helmet Lights are ideal for use in a number of specific Class I hazardous locations. Class I (NEC-500-5) is • Petroleum refineries, and gasoline defined as those areas in which flammable storage and dispensing areas gases or vapors may be present in the air • Industrial firms that use flammable in sufficient quantities to be explosive or liquids in dip tanks for parts cleaning ignitable. Class II (NEC-500-6) refers to or other operations those areas made hazardous by the • Dry cleaning plants where vapors presence of combustible dust. (See list at from cleaning fluids can be present right for some examples of Class I and • Companies with spraying areas Class II hazardous locations.) where products are coated with paint or plastics Division 2 (NEC-500-5, 6, 7) means that • Aircraft hangars and an encounter with Class I or Class II fuel-servicing stations hazardous materials is an abnormal • Utility gas plants, and operations situation; material is expected to be involving storage and handling of confined within closed containers or liquefied petroleum gas or natural gas closed systems and will be present only through accidental rupture, breakage or Class II unusual faulty operation. • Grain elevators, flour and feed mills • Plants that manufacture, use or store Groups A, B, C, D refer to specific magnesium or aluminum powders chemicals and Group G refers to specific • Plants that have chemical or particulates—please contact the metallurgical processes… MSA Customer Service Center at producers of plastics, medicines 1-800-MSA-2222 for more information and fireworks, etc. about any of these Groups. • Producers of starch or candies • Spice-grinding plants, sugar plants and cocoa plants • Coal preparation plants and other carbon-handling or processing areas

Do not service or charge any MSA light while in a hazardous environment. Do not use rechargeable batteries in these lights, as the FM and CSA approvals will be voided.

Note: this bulletin contains only a general description of the Corporate Headquarters MSA Canada Offices and representatives worldwide products shown. While uses and performance capabilities are P.O. Box 426, Phone 1-800-967-2222 For further information: described, under no circumstances shall the products be used Pittsburgh, PA 15230 USA Fax 1-800-967-0398 by untrained or unqualified individuals and not until the product Phone 412-967-3000 MSA Mexico instructions including any warnings or cautions provided have www.MSAnet.com Phone 01 800 672 7222 been thoroughly read and understood. Only they contain the U.S. Customer Fax 52 - 44 2227 3943 complete and detailed information concerning proper use and Service Center MSA International care of these products. Phone 1-800-MSA-2222 Phone 412-967-3354 Fax 1-800-967-0398 FAX 412-967-3451 ID 0616-07-MC / Jun 2009 © MSA 2009 Printed in U.S.A. Swing-Ratchet Suspension

Skullgard Cap with Swing-Ratchet Suspension

Self-adjusting The only self-adjusting crown assembly reversible 360˚ Padded ratchet suspension Perforated Sweatband Topgard Cap with Swing-Ratchet Suspension Self-adjusting slide

Thermalgard Cap with Swing-Ratchet Suspension Normal Position Reversible Ratchet napestrap

Reverse Position

5 360-degree perforated sweatband 5 Correct positioning assured enhances comfort 5 Fas-Trac® Ratchet Suspension's 5 Easy to use, comfortable and stable nape slide feature

For the greatest degree of The Swing-Ratchet Suspension Approvals protection, a helmet should easily converts MSA’s V-Gard®, V-Gard, Topgard, Thermalgard, and always be worn with the brim Topgard®, Thermalgard®, and Skullgard Helmets equipped with facing forward. Skullgard® Caps and Hats from the Swing-Ratchet Suspension are the normal wearing position to third-party certified by the Safety However, for those times when you the reverse without removing Equipment Institute (SEI) in both need the option of turning your the suspension. standard and reverse positions and helmet around, MSA’s Swing- meet all applicable requirements of Ratchet Suspension is the answer. ANSI Z89.1-2003 for Type I helmets. Suspension converting V-Gard, Topgard, 5 Thermalgard, and Skullgard Hats and Caps from normal wearing position to the reverse.

Ordering Information Helmets plus Swing-Ratchet Suspension, complete Medium V-Gard Cap, white, with Swing Ratchet Suspension 10004689 Skullgard Cap, natural, with Swing Ratchet Suspension 816651

1 5 Replacement Swing Ratchet Suspension (6 /2-7 /8) V-Gard 816645 Topgard & Thermalgard 816648 Skullgard 816654

Note: This Bulletin contains only a general Corporate Headquarters Offices and representatives worldwide description of the products shown. While P.O. Box 426, Pittsburgh, For further information: uses and performance capabilities are PA 15230 USA described, under no circumstances shall Phone 412-967-3000 the products be used by untrained or www.MSAnet.com unqualified individuals and not until the U.S. Customer Service Center product instructions including any Phone 1-800-MSA-2222 warnings or cautions provided have been Fax 1-800-967-0398 thoroughly read and understood. MSA Canada Only they contain the complete Phone 416-620-4225 and detailed information Fax 416-620-9697 concerning proper use and care of these products. MSA Mexico Phone 52-55 21 22 5770 Fax 52-55 5359 4330 ID 0614-04-MC / Aug 2006 © MSA 2006 Printed in U.S.A. MSA International Phone 412-967-3354 FAX 412-967-3451 V-Gard® Helmets with a Choice Five suspensions available: one to fit every need

V-Gard® Protective Caps and Hats 1-Touch™ Suspension V-Gard Protective Caps and Hats from MSA The first real innovation in suspension adjustment NEW! consist of a polyethylene shell and your choice of in 20 years features: suspension system, working together as a • Easy squeeze opening protective system. V-Gard headwear features • One-hand slide adjustment advanced styling in cap and hat styles, with the • Comfortable and stable fit 1 cap available in three sizes: small (6 – 7/8), • Adjustable dual nylon straps 1 1 standard (6/2 – 8) and large (7 – 8/2). V-Gard Caps and Hats meet or exceed the Standard Size Cap Hat applicable requirements for a Type I helmet (top White 10057441 10058321 impact) as outlined in ANSI Z89.1-2003, Class E, Blue 10057442 10058320 and also are certified to in CSA 294.1-2005 (Class E) with 1-Touch and Fas-Trac suspensions. Yellow 10057443 10058318 Orange 10057444 10058322 V-Gard Caps and Hats are not specifically Red 10057446 10058324 designed to protect against lateral blows from Green 10057445 10058323 the front, side, or rear. (MSA’s Vanguard™ II Gray (navy) 10057447 10058319 protective helmets are so designed and must be Hi-Viz Orange 10057420 10058326 used if lateral protection is desired. For more Hi-Viz Yellow-Green 10061514 10061516 information, contact your local MSA distributor.)

Staz-On® Suspension V-Gard with Staz-On Suspension • Comfortable, four-point webbed suspension Standard Size Cap Hat Standard Size Cap Hat • Adjustable dual nylon crown straps White 463942 454733 Robin’s egg blue 463111 — • Perforated vinyl sweatband Blue 463943 454732 Brown 464658 1/ • Three sizes available: Small (6 – 7 8), Hi-Viz orange 488148 1 1 Yellow 463944 454730 Standard (6/2 – 8), and Large (7– 8/2) Orange 463945 454734 Silver 484340 Red 463947 454736 Tan 461180 Green 463946 454735 Black 475235 Gray (navy) 463948 454731 Light buff 478237 Gold 464852 — Purple 488398 Hi-Viz lime green 815558

Staz-On Suspension

Staz-On Suspension 1 Small (6–7/8) 467386 1 Standard (6/2 – 8)*NEW part number 10087218 SAME great product 1 Large (7– 8/2) 492566 Fas-Trac® Ratchet Suspension UniPro™ Suspension-Standard Cap Swing-Ratchet Suspension for all-day comfort, with quick and easy Only The only self-adjusting reversible adjustments for basic comfort ratchet suspension • Large knob for easy adjustment • Energy-absorbing, four-point, one-piece The Swing-Ratchet Suspension easily converts • Comfortable, four-point webbed plastic suspension your V-Gard®, Topgard®, Thermalgard® or suspension • Integral napestrap sits low on the back of Skullgard® hat or cap from the normal wearing • Adjustable dual nylon crown straps the head position to the reverse wearing position without • Perforated vinyl sweatband wipes • Baseball-cap-style pinlock adjustment having to remove the suspension! clean easily • Comfortable and absorbent replaceable 1/ • Three sizes available: Small (6 – 7 8), sweatband 1 1 Standard (6/2 – 8), and Large (7 – 8/2) 1 The Swing-Ratchet has a 360° perforated • Adjusts to fit sizes 6 /2 – 8 in standard size cap sweatband to enhance comfort. With the Fas- ® V-Gard with Fas-Trac Suspension V-Gard w/ UniPro Suspension Trac ratchet’s ease of use and the slide feature, Standard Size Cap Hat you are assured of the correct positioning of the UniPro Suspension napestrap for comfort and stability. White 475358 475369 1 Standard only (6/2 – 8) 10004788 Blue 475359 475368 Yellow 475360 475366 Standard Size Cap Orange 475361 496075 White 10004760 Self-adjusting crown assembly Red 475363 475371 Blue 10004762 Green 475362 475370 Yellow 10004761 Gray (navy) 475364 475367 Orange 10004767 360˚ Padded Self-adjusting slide Perforated Sweatband Gold 475365 — Red 10004763 Hi-Viz orange 488146 10021292 Green 10004765 Small Size Cap Gray (navy) 10004766 Hi-Viz orange 10004764 White 477477 Reverse Blue 477478 Hi-Viz lime green 10017732 Position Normal Position Yellow 477479 Reversible Ratchet Large Size Cap napestrap White 477482 Ordering Information Blue 477483 Helmets plus Swing-Ratchet Suspension, Yellow 477484 complete Medium V-Gard cap, white, with Fas-Trac Ratchet Suspension Swing Ratchet Suspension 10004689 1 Small (6 – 7 /8) 492567 1 5 1 Replacement Swing Ratchet Suspension (6/2 -7/8) Standard (6 /2 – 8)*NEW part number 10087220 SAME great product 1 Large (7 – 8 /2) 492568 V-Gard 816645

UniProm™ Suspension

! WARNING Do not mix sus pen sion and helmet sizes. Make sure the sizes match (example: standard size suspension with standard size helmet). UniPro, 1-Touch and Swing Ratchet suspensions should be used only in standard size V-Gard helmets. Use only MSA suspensions with an MSA helmet. Failure to comply with the above will reduce the energy-absorbing ability of the pro tec tive helmet, which can result in serious injury or death. Fas-Trac Suspension

Note: This Bulletin contains only a general description of Corporate Headquarters MSA Mexico the products shown. While uses and performance P.O. Box 426, Pittsburgh, PA 15230 USA Phone (52) 55 2122 5770 capabilities are described, under no circumstances shall Phone 412-967-3000 Fax (52) 55 5359 4330 the products be used by untrained or unqualiﬁed www.MSAnet.com MSA International individuals and not until the product instructions including U.S. Customer Service Center Phone 412-967-3354 any warnings or cautions provided have Phone 1-800-MSA-2222 FAX 412-967-3451 been thoroughly read and understood. Only Fax 1-800-967-0398 they contain the complete and detailed MSA Canada information concerning proper use and care Phone 416-620-4225 of these products. Fax 416-620-9697 ID 0613-27-MC / Dec 2007 © MSA 2007 Printed in U.S.A. HEARING PROTECTION

Passive Hearing Protection Passive Hearing Protection Guarding workers against the daily hazards of noise is of paramount concern in HPE—headband model 10061271 countless industries. The challenge is to balance personal attenuation devices with comfort. A worker who takes off hearing protection to rub sore ears is a worker at HPE—for slotted caps 10061272 risk. MSA provides a wide selection of hearing protection designed for the most Hygiene Kit for HPE, complete with cushions and inserts 10061291 demanding applications, offers protection with a variety of Noise Reduction Ratings, EXC—headband model 10061229 and does it with the benefits of style and comfort. Noise Reduction Rating (NRR) is third-party certified in accordance with ANSI S3.19-1974, EN352 and meets CSA EXC—for slotted caps 10061230 Class A. Cap Model Noise Reduction Ratings listed below are for medium Hygiene Kit for EXC, complete with cushions and inserts 10061292 V-Gard helmets only. Noise Reduction Rating and Attenuation Values for MSA XLS—for slotted caps 10061535 Topgard, Advance, Thermalgard, Vanguard II, Wildland T and Super-V slotted helmets may vary. Contact MSA for more information. Hygiene Kit for XLS, complete with cushions and inserts 10061537

HPE Muff (NRR – 26dB) HPE Cap Model (NRR – 27dB) Designed specifically for very high noise levels, the powerful Muff/Cap Model is ideal for airfields, power plants and other areas with intense noise. The HPE Muff/Cap Model provides the highest-rated protection available for low-frequency environments. A padded headband and super-soft ear cushions guarantee all-day comfort while ensuring full-time protection.

EXC Muff (NRR – 24dB) EXC Cap Model (NRR – 25dB) The ear muff is so comfortable that you always want to wear it. Unique injection molded inserts provide excellent attenuation and maximum space for the ears inside the cap. Headband model offers force adjustment for individual fit. The helmet-mounted version has a spring design that offers low pressure tension and a high level of comfort.

XLS Cap Model (NRR – 23dB) Designed to fit comfortably under safety hardhats and faceshields, it features easy-to-remove ear cushions for quick cleaning and replacement. The XLS Muff offers agressive “protection in low-moderate noise environments

Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com • QuickLit Fax Information: 1-800-672-9010 127 HEARING PROTECTION

Soprano™ Muff (NRR-25dB) for Hats Soprano Muff Designed to fit all full brim hats, Soprano Muff Kit for Full Hats (NRR 25) 10034487 the Soprano Muff provides high-level hearing protection. Economuff Line (The Muff reduces helmet Economuff Earmuff 10004291 class to Class “C”.) Economuff Multi-Position Earmuff 10061273 Comfort Band, each (must order in multiples of 20) 10003344 Sound Blocker Cap Model ™ Economuff Line Sound Blocker 26 cap model (for Defender Faceshield Frame) 10026398

Economuff Earmuff (NRR – 20dB) Sound Blocker 26 cap model* (for non-slotted caps) 10022021 The Economuff Earmuff comes with the Reusable Ear Plugs features you expect from MSA hearing protection. Comfortable ear pads ensure Tri-Seal Reusable Silicone Ear Plugs (corded) Dispenser box (suit- 10005607 all-day wearing without fatigue, and the able for wall hanging) of 100 individ. packaged pairs durable design provides protection in tough, dirty environments. Lightweight at Disposable Ear Plugs just 8.0 ounces. Round Ear Plugs (NRR – 29dB) Economuff Multi-Position Earmuff FormFit Disposable Urethane Foam Ear Plugs (non-corded) 10009333 Over-the-Head (NRR – 24dB) Dispenser Box of 200 individually packaged pairs Behind-the-Head and Under-the-Chin 23 FormFit Disposable Urethane Foam Ear Plugs (corded) Dispenser 10009332 (NRR – dB) Box of 200 individually packaged pairs The Economuff Multi-Position Earmuff * Tested on Comfo and Skullgard Helmets. comes with comfortable ear pads and padded headband to ensure all-day wearing without fatigue, and the durable design provides protection in Reusable Ear Plugs tough, dirty environments. • Extremely lightweight Tri-Seal™ Reusable Silicone Ear Plugs (NRR – 25dB) • Multi-position (over head/ Ruggedly designed, made of soft, comfortable under chin/behind head) silicone, these reusable ear plugs are easy to insert • Includes crown strap in the ear and economical. They offer protection Comfort Band™ Hearing Protector comparable to many MSA earmuffs. Tri-Seal corded (NRR – 23dB) plugs are available in dispenser boxes of 100 individually packaged pairs. Designed to be worn under the chin, the MSA Comfort Band Hearing Protector is Disposable Ear Plugs made with soft, easily cleanable pods and a durable plastic neck band. While not in use, FormFit™ Disposable Foam Ear Plugs the Comfort Band Hearing Protector can be For users who prefer to dispose of their plugs after left resting around your neck. each use, the FormFit plug is the answer. Easy to use and affordable, FormFit ear plugs offer very aggressive noise reduction while being very comfortable to wear. Available in corded and uncorded versions, in dispenser boxes of 200 pair. Sound Blocker™ 26 Hearing Protection (NRR – 26dB) Designed for high noise areas such as industrial plants and construction sites, the Sound Blocker 26 comes in two models, one for use with the Defender faceshield frame and a non-slotted cap model.

128 Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com • QuickLit Fax Information: 1-800-672-9010 HEARING PROTECTION

Electronic Hearing Protection Electronic Hearing Protection Guarding people against the daily hazards of noise is of paramount ListenOnly Basic FM Pro CutOff Pro concern in countless industries. The challenge is to balance personal attenuation devices with comfort and the ability of communication Headband model 10061275 10061280 10061278 and listening to music, so that workers will wear their hearing Slotted cap model* 10061277 10061281 10061279 protectors all the time. With over 40 years of experience, MSA now offers a new wide range of hearing protectors with built-in Hygiene Kit 10061536 10061293 10061293 electronics – from basic functions to high-specification Sound quality mono stereo stereo communication devices. You have Volume memory — — the choice between headband and helmet-mounted versions. Battery save function — — All products are comfortable Battery life (approx. hours) 120–140 300 hearing protectors, designed to prevent you Downleads for Basic and Pro Line from feeling isolated, 3.5 mm Stereo Plug 10061538 thereby encouragaing you to use them 3.5 mm Mono Plug 10061539 and so protecting 2.5 mm Mono Plug 10061540 your hearing for the rest of your life. Hands Free, 2.5 mm Stereo Plug 10062072 Noise Reduction * fits V-Gard, Advance, Topgard & Thermalgard slotted caps Rating (NRR) is third- party certified in accordance with ANSI S3.19-1974 and EN352-3. Also meets CSA Z94.2. CutOff Slotted Cap Model on Advance Cap

Basic and Pro Line The line features standard and advanced electronics with a very good price-to-performance ratio. Built-in features, such as FM and CutOff are optional. ListenOnly Basic Headband Model (NRR – 24dB) ListenOnly Basic Slotted Cap Model (NRR – 22dB) External connection to CD, MP3-player or scanner ListenOnly Basic Headband Model • Connection lead with 3.5 mm stereo jack included (fits most CD and MP3-players, etc.) • The cable can be removed easily when not needed FM Pro Headband Model (NRR – 24dB) FM Pro Slotted Cap Model (NRR – 22dB) Built-in radio receiver—stereo • Scan stations automatically • Memory for last selected station and volume • Automatically switches off to save batteries • Battery life of 120–140 hours CutOff Pro Headband Model ((NRR – 24dB) CutOff Pro Slotted Cap Model (NRR – 22dB) FM Pro Headband Model Built-in level dependent function protects without your feeling isolated • Lets through speech and other harmless sounds while protecting you from harmful noise • Battery life of 1000 hours • Amplification of weak sounds • Auxilliary input for connection of external devices CutOff Pro Headband Model

Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com • QuickLit Fax Information: 1-800-672-9010 129 HEARING PROTECTION Protection and communication with the Connect by Cable Series Effective noise attenuation and amplification at the same time

Connect By Cable Connect-by-Cable Connect By Cable Cap Model A comfortable hearing protector Connect by Cable headband model (NRR – 25dB) 10064515 equipped with a hard-wired lead (3.5 mm) and boom microphone. Connect by Cable slotted cap model (NRR – 23dB) 10064516 • The standard Connect by Cable model comes with a hard-wired Hygiene Kit 10061293 cable for connection to an MSA Push-To- Talk,or lapel microphone (No noise cancelling) • Noise-cancelling boom microphone permits two-way communication Connect-by-Cable Earmuffs with minimal interference from background noise • Headband version comes with padded headband with adjustable pressure • Muffs come with a hard-wired 3.5 mm cable adapter • All MSA Helmet Communication System adapters will work with these muffs

Supreme Pro Supreme Pro

Our top model. Provides optimum protection with Supreme Pro headband model (NRR – 18dB) 10061285 high amplification, AUX input and watertight battery compartment. Both earmuffs are shaped Hygiene Kit 10061294 to suit both right-handed and left-handed shots. • Two separate, well-shielded microphones for optimum stereo effect and location of sound direction • High amplification and natural sound reproduction without “chopping” • Around 600 hours battery life with two standard AAA batteries • AUX input for connecting external audio sources, such as a radio. Lead with 3.5 mm mono jack plug included

130 Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com • QuickLit Fax Information: 1-800-672-9010

MSA Products for Construction

Hearing Protection Passive Helmet-Mounted Hearing Protectors Sound Control Cap Models Sound Control Cap Models are designed for easy attachment to slotted MSA Caps and help to reduce the effects of excessive noise. Noise Reduction Rating (NRR) is third-party tested in accordance with ANSI S3.19-1974, CSA Class A and EN352-3.

Sound Control Cap Models HPE cap model, complete with brackets (NRR 27 dB) 10061272 EXC cap model, complete with brackets (NRR 25 dB) 10061230 EXC cap model HPE cap model XLS cap model XLS cap model, complete with brackets (NRR 23 dB) 10061535

left/RIGHT Cap Models The cups for left/RIGHT™ helmet-mounted models are specially designed for each ear and can be adjusted individually to the angle of the ear. Each cap model comes complete with brackets.

left/RIGHT Cap Models left/RIGHT, LOW, White (NRR 21) 10087439 left/RIGHT, MEDIUM, Blue (NRR 25) 10087429 left/RIGHT, HIGH, Yellow (NRR 28) 10087422

left/RIGHT Cap Models

Soprano™ Muff for Hats Designed to fit all full brim hats, the Soprano Muff provides high-level hearing protection. NOTE: The addition of the Soprano muff reduces helmet rating to Class C.

Soprano Muff Soprano Muff Kit for full-brim Hats (NRR 25 dB) 10034487

Sound Blocker™ 26 Hearing Protection for Faceshield Frames Designed for high noise areas such as industrial plants and construction sites, the Sound Blocker 26 comes in two models, one for use with the Defender faceshield frame and a non-slotted cap model.

Sound Blocker Cap Models Sound Blocker 26 cap model for Defender Faceshield Frame (NRR 26 dB) 10026398 Sound Blocker 26 cap model for non-slotted caps* (NRR 26 dB) 10022021 Defender + Frame , Sound Blocker 26 Muff Assembly, *Tested on Comfo and Skullgard caps. shown with visor

16 Customer Service Center: 1-800-MSA-2222 • Website: www.MSAnet.com Topgard® Protective Helmets 5

Topgard Slotted Caps and Non-Slotted Ordering Information Hats are built for use by utilities and Topgard Helmet Assemblies other industries where head protection Topgard Slotted Cap Topgard Non-slotted Hat with dielectric protection is necessary. Color w/1-Touch® w/Fas-Trac® w/1-Touch w/Fas-Trac Suspension Suspension Suspension Suspension Limited resistance to top impact or penetration is retained over a wide range of White 454728 475385 454719 475393 temperatures. Yellow 454721 475378 454712 475387 Gray 454722 475379 454713 • Topgard Caps and Hats meet all applicable require- Blue 454723 475380 • • ments for a Type I helmet (top impact) as outlined in Orange 454725 475382 • • ANSI/ISEA Z89.1-2009 (Class E) and CSA Z94.1-2005 Green 454726 475383 • • (Class E). These caps and hats also meet the ANSI/ISEA Z89.1-2009 voluntary standard for low Red 454726 475384 • • temperature [LT] and reverse donning. Look for the Bright Orange • 804396 • 804397 official reverse donning logo to determine if White with your hardhat may be worn backwards without void- lamp bracket 448914 • • • and cord holder ing approvals.

MSA can customize your helmets with your com- Replacement Suspension

pany logo and choice of reflective striping. For more 1-Touch Suspension (61/2–8) 10061127 information regarding logos and stripes, contact Fas-Trac Suspension (61/2–8) 473333

MSA Logo Express at 1.800.MSA.LOGO. 5 Swing-Ratchet Suspension (61/2–7 ⁄8) 816648

Note: this bulletin contains only a general description of the Corporate Headquarters MSA Mexico products shown. While uses and performance capabilities are P.O. Box 426, Pittsburgh, PA 15230 USA Phone 01 800 672 7222 described, under no circumstances shall the products be used Phone 412-967-3000 Fax 52-44 2227 3943 by untrained or unqualified individuals and not until the product www.MSAnet.com MSA International instructions including any warnings or cautions provided U.S. Customer Service Center Phone 412-967-3354 have been thoroughly read and understood. Only they Phone 1-800-MSA-2222 FAX 412-967-3451 contain the complete and detailed information Fax 1-800-967-0398 concerning proper use and care of these products. MSA Canada Phone 416-620-4225 ID 0612-06-MC / July 2009 Fax 416-620-9697 © MSA 2009 Printed in U.S.A. Topgard® Protective Helmets 5

MSA can customize your helmets with your com- Replacement Suspension

pany logo and choice of reflective striping. For more 1-Touch Suspension (61/2–8) 10061127 information regarding logos and stripes, contact Fas-Trac Suspension (61/2–8) 473333

MSA Logo Express at 1.800.MSA.LOGO. 5 Swing-Ratchet Suspension (61/2–7 ⁄8) 816648

Topgard Slotted Hard Hats are built for use by utilities, oil, gas and petrochemical, and other industries where head protection is needed in environments with higher temperature exposures. classification: Type I application: General purpose; elevated temperature 1 Shell material: Polycarbonate available Styles: Slotted Cap; Slotted Full-Brim Hat

Sizes: Standard (6 1⁄2 – 8") Standards: ANSI/ISEA Z89.1-2014 (Class E); CSA Z94.1-2005 (Class E) certification: Third-party by SEI customization: Imprinting and striping available

Topgard Protective Caps

color topgard Slotted cap-Style hard hat (standard size) color topgard Slotted cap-Style hard hat (standard size) w/ 1-touch w/ Fas-trac® iii w/ 1-touch w/ Fas-trac® iii Suspension Suspension Suspension Suspension White 454728 475385 green 454726 475383

yelloW 454721 475378 red 454727 475384

gray 454722 475379 bright — 804396 orange

blue 454723 475380 White 448914 — W/lamp bracket and cord holder

orange 454725 475382

Topgard Cap with Fas-Trac III Suspension

1Topgard Caps and Hats can withstand temperatures produced by radiant heat loads up to, but not exceeding, 275ºF. Topgard Full-Brim Hard Hats Replacement Suspensions

color topgard Slotted Full-brim hat (standard size) Suspension type (4-point, unless otherwise noted) w/ 1-touch w/ Fas-trac iii Fast-trac iii 1-touch Swing ratchet 1 Suspension Suspension White 454719 475393 HARD HAT SIZE

topgard 10153384 10061127 816648 cap-Style or Full-brim (Standard) yelloW 454712 475387

FaS-trac iii 10153518 •For use with MSA SWeatband Fas-Trac® III Suspension acceSSory •Optional, moisture- wicking and washable gray 454713 — •Can be attached/ replaced while suspension is assembled in helmet • Sold ONLY in packages of 10 orange — 804397

Use only the indicated MSA suspension in your MSA hard hat. Do not mix suspension sizes and hard hat sizes (i.e., putting a standard-sized suspension in a large hard hat or any other mismatched combination). Do not use competitor suspensions in MSA hard hats. Inspect your suspension frequently. Suspensions should be replaced every 12 months, regardless of inspection results. Replace immediately (along with the hard hat), if an impact has occurred. Failure to follow these instructions will reduce the energy absorbing ability of the hard hat to receive impact, and could result in serious injury or death.

please contact mSa customer Service at 1-800-mSa-2222 for details about topgard helmets or other head protection or hard hat accessory products. you can also visit us on the web at mSaSafety.com.

Note: This Bulletin contains only a general MSA – The Safety Company description of the products shown. While uses 1000 Cranberry Woods Drive and performance capabilities are described, Cranberry Township, PA 16066 USA under no circumstances shall the products be Phone 724-776-8600 used by untrained or unqualified individuals www.MSAsafety.com and not until the product instructions U.S. Customer Service Center including any warnings or cautions provided Phone 1-800-MSA-2222 have been thoroughly read and understood. Fax 1-800-967-0398 Only they contain the complete and detailed information MSA Canada concerning proper use and care Phone 1-800-672-2222 of these products. Fax 1-800-967-0398 MSA Mexico ID 0612-06-MC / Nov 2018 Phone 01 800 672 7222 © MSA 2018 MSA safety .com V-Gard® Industrial Safety Helmets The ”all-round” helmet

V-Gard Push-Key

V-Gard Fas-Trac® III

V-Gard Safety Helmet - Key features and benefits

• Reliable, UV stabilised HDPE non-vented helmet shell • For many industrial applications the ideal and most economic solution • ELECTROSTATIC-INERIS certified (testing according to EN 13463-1). Suitable for use in ATEX environments hazardous zones 1, 2, 20, 21, 22 • Economic electrician helmet meeting EN 397 440 V AC and EN 50365 (Triangle symbol is engraved inside the shell) and part of visor testing GS-ET-29 Class 1 and Class 2 • GOST certified (–50°C) • Standard slots to easily attach MSA visors and/or ear muffs • 2- or 3-point chinstraps available • 6 shell colours: white, yellow, red, blue, green, orange • Optional: text or full colour picture printing an all helmet sides; individual naming stickers; reflective stickers • Lifetime: 2 years storage, +4 years service time; MSA delivers stickers to note date of first use and stick to inside shell • 4 suspensions available: -Push-Key with slide adjustment and sweat-wicking foam sweatband -Push-Key with slide adjustment and wipeable PVC sewn in sweatband -Fas-Trac® III with wheel ratchet and sweat-wicking foam sweatband -Fas-Trac® III with wheel ratchet and wipeable PVC sewn in sweatband

V-Gard Technical Datasheet, Rev.00, February 2016 MSA safety .com V-Gard Industrial Safety Helmets The ”all-round” helmet

MSA Suspensions - General features and benefits

• Overhead straps made of woven polyester providing high comfort and long term, consistent shock absorption performance • Ensures consistent performance and comfort level even under the influence of moisture or low temperatures • Sophisticated 4 point attachment: good positioning, stability and better air circulation • Ideal positioning of the harness through height and length adjustment: perfect for use with face masks • Self-adjusting textile crown straps for fast height adjustment and comfortable fit

MSA Fas-Trac® III suspension Features and benefits

• BALANCE & STABILITY : – Lower nape strap improves retention: Helmets stay on when leaning over – Adjusts for a custom fit to the back of the head • HEADBAND COMFORT: – The comfort pad by separating the ratchet from the head, cradles MSA Push-Key suspension the head increasing comfort and cooling airflow Features and benefits – Prevents hair from getting pulled • EASE OF USE: • EASE OF USE: – Ratchet offers smooth rotation: reduced effort to turn – This is the fastest sliding suspension on the market: simple push – Easy grip knob adjustable even with gloves on to loosen, squeeze to tighten • ADJUSTABILITY: – Can be adjusted with one hand even when worn – Three levels of nape height adjustment giving superior nape fit • SURE FITTING: – Avoids interference with other PPE such as ear muffs – It offers greater retention capacity than competitive sliding • SWEATBAND COMFORT: suspensions because it's so much easier to select the best – Largest sweatband surface area on the market covers more of the adjustment position headband and user's forehead for increased comfort • ADJUSTABILITY: – 2 different sweatband options: sewn in PVC perforated wipeable – 2 levels of nape adjustment for fitting comfort or sweat-wicking washable foam(breathable fabric allows direct air – Designed to avoid interference with other PPE such as ear muffs permeation) • SWEATBAND COMFORT: – Replaceable foam sweatband can be attached over the existing – 2 different options: sewn in PVC perforated wipeable or sweat- sweatband without demounting the suspension wicking foam

Also available Terry cotton washable sweatband that can be used over both sewn in PVC or replaceable foam sweatbands for increased user comfort

V-Gard Technical Datasheet, Rev.00, February 2016 MSA safety .com V-Gard Industrial Safety Helmets The ”all-round” helmet

Technical Specifications

Shell Material High Density Polyethylene (HDPE) stabilized, non-vented Weight 269 g Suspensions Weight Push-Key with slide adjustment and sweat-wicking foam sweatband: 66 g Push-Key with slide adjustment and wipeable PVC sewn in sweatband: 70 g Fas-Trac® III with wheel ratchet and sweat-wicking foam sweatband: 89 g Fas-Trac® III with wheel ratchet and wipeable PVC sewn in sweatband: 91 g Webbing Black Polyester (PET), double straps, 4 points Sweatband material Push-Key with wipeable sewn in PVC sweatband and Polyurethane (PU) internal foam. Nontoxic PVC in contact with the head. Push-Key with sweat-wicking Polyurethane (PU) internal grey foam and grey Polyamide (PA) ﬁnish in contact with the head Fas-Trac® III with wipeable sewn in PVC sweatband and Polyurethane (PU) internal foam. Nontoxic PVC in contact with the head. Fas-Trac® III with sweat-wicking Polyurethane (PU) internal grey foam and grey Polyamide (PA) ﬁnish in contact with the head. Machine or hand washing (max. 50 cycles)

Headband Fas-Trac® III : Polypropylene (PP) Push-Key : Low Density Polyethylene (LDPE) Clips Grey Polypropylene (PP) Comfort pad (Fas-Trac® III) Low Density Polyethylene (LDPE) Adjustment Fas-Trac® III (Ratchet): Polyoxymethylene (POM), Polypropylene (PP) and Polyamide (PA) Push-Key (Button) : Polyoxymethylene (POM) Size 52-64 cm Metal parts No Approvals Standard Certified by European notified body INSPEC (0197) according to: EN 397: 2012 Mandatory tests Shock absorption, resistance to penetration, flame resistance, chinstrap anchorage Optional tests Very low temperature / -30°C, electrical insulation / 440 V AC Other standards Certified by European notified body INSPEC (0197) according to: EN 50365:2002 electrical class 0 nominal voltage up to 1000 V A.C. and 1500 V D.C. The voltage used for this test is 10 000 V.

Certiﬁed by INERIS to EN 13463-1: 2001 for safe use in ATEX areas* (ELECTROSTATIC-INERIS testing): Certiﬁcate n°29406 - Industry: Dust: hazardous zones 20, 21, 22 (all zones) Gas: zones 1 and 2 with gas group IIA (propane) - Mines: any type of extraction and any depth *Caution:when working in an ATEX area operatives must be fully equipped with appropriate PPE eg. dissipative shoes (earth resistance less than 1.108 Ω), not just suitable industrial helmets!

Part of GS-ET-29 class 1+2 visor testing. Lifetime guidelines Storage time (when helmet not 2 years from shell injection date (helmet packed in proper condition, not exposed to light, chemical or used) any type of pollution). Store in a proper storage bag and/or in a closed cabinet to avoid extended exposure to sunlight, cold, humidity, exhaust fumes, etc. If the helmet has been stored more than 2 years, deduct the extra storage time from the recommended helmet’s service life. NB: For EN 50365 class 0 helmets recommended storage temperature 20 ±15 °C to ensure performance Service life (in addition to the stor - 4 years from actual starting date of use. MSA recommends writing the date of ﬁrst use onto a sticker age time) (supplied with each helmet) and then sticking into the shell.This is normally the point at which service life starts Suspension (Push-Key and Fas-Trac® III) Replace when damaged or contaminated , or as required for hygienic reasons

V-Gard Technical Datasheet, Rev.00, NFeobvreumarbye 2r 02106 15 MSA safety .com V-Gard Industrial Safety Helmets The ”all-round” helmet

Packaging

Part No. Description One helmet in a protective plastic bag printed with instructions, 1 tab suspensions fitted or Individual (sales unit) 4 suspensions fitted (GVxxx-xxAxxxx-xxx) Minimum order quantity: 20 helmets with EAN code on the box Box Box size: 706x586x455 mm (one tab fitted) or 720x610x460 mm (4 tab fitted) 200 helmets (10 boxes of 20 helmets) Pallet Pallet size: 1200 x 730 x 1980 mm

Ordering Information

V-Gard Fas-Trac® III V-Gard Fas-Trac® III V-Gard Push-Key V-Gard Push-Key Colors RAL Code PVC sweatband Foam sweatband PVC sweatband Foam sweatband White RAL 9003 GV112-0000000-000 GV119-0000000-000 GV111-0000000-000 GV113-0000000-000 Yellow RAL 1018 GV122-0000000-000 GV129-0000000-000 GV121-0000000-000 GV123-0000000-000 Red RAL 3001 GV132-0000000-000 GV139-0000000-000 GV131-0000000-000 GV133-0000000-000 Green RAL 6024 GV142-0000000-000 GV149-0000000-000 GV141-0000000-000 GV143-0000000-000 Blue RAL 5015 GV152-0000000-000 GV159-0000000-000 GV151-0000000-000 GV153-0000000-000 Orange RAL 2001 GV162-0000000-000 GV169-0000000-000 GV161-0000000-000 GV163-0000000-000 ATO digit when Part No. Description ﬁtted to helmets 10162752 Fas-Trac® III suspension with ratchet and sewn in PVC sweatband GVxx2 10162755 Fas-Trac® III suspension with ratchet and replaceable, washable, foam sweatband GVxx9 10162507 Push-Key suspension with slide adjustment and sewn in PVC sweatband GVxx1 10162508 Push-Key with slide adjustment and replaceable foam sweatband GVxx3 10153518 Fas-Trac® III foam sweatband (10 pcs) – replacements for 10162755 or GVxx9 or over 3335612-SP Push-Key foam sweatband (10 pcs) – replacements for 10162508 or GVxx3 696688 Terry cotton (Terri-Band) sweatband (10 pcs) – for use over sewn in PVC sweatband

Other accessories and options Ask for our detailed data-sheets

Options Lamp brackets Options Logo Customization Accessories or Options Chinstraps Accessories or Options High visibility stickers Accessories Helmet mounted ear-muﬀs Accessories Individual naming Accessories Frame and visors Accessories Winter liners Accessories Cooling liners Accessories Neck curtains

V-Gard Technical Datasheet, Rev.00, February 2016 MSA safety .com V-Gard® Helmets with a Choice Five suspensions available: one to fit every need

Staz-On Suspension

UniProm™ Suspension

The MSA V-Gard Helmet, with its distinctive trademark “V” design, is a world recognized brand known for comfort, quality, and durability. MSA has sold well over 100 million V-Gard Helmets since its introduction—so many in fact, that the iconic “V” design has been a mainstay for many years on even the toughest worksites. \ Full Brim Hat shown with Fas-Trac® III Suspension

Features Specifications STANDARDS COMPLIANCE • Superior top impact protection ANSI/ISEA Z89.1-2014 CSA Z94.1-2014 • Fas-Trac III suspension is the most comfortable on the market— CLASSIFICATION Type I, Class E preferred by 92% of users CERTIFICATION Third-party by SEI • Designed for use with MSA accessories to ensure compliance with the helmet & accessory APPLICATION(S) General Purpose PRODUCT SIZES 1 Markets Standard (6 ⁄2” to 8”) SHELL MATERIAL Virgin high-density polyethylene (HDPE) • Oil, gas and petrochemical with UV inhibitor • General industry and manufacturing AVAILABLE STYLES Slotted Hat • Electric/utilities AVAILABLE SUSPENSIONS Fas-Trac® III Ratchet Staz-On® Pinlock Closure • Construction 1-Touch Slide Closure Customization Swing Ratchet REQUIREMENTS FOR Reverse Donning, Lower Temperature, • 27+, factory applied reflective or retro-reflective stripes OPTIONAL FEATURES (Z89.1) Higher Temperature, Hi-Viz (as indicated) • Multiple printing services: one-color logo to digital photos; COLORS 12 (stocked); other color options available, including custom colors up to four locations OTHER PPE MSA accessories, including MSA slotted • For additional details, visit msasafety.com KEYWORD: logo and unslotted hat-mounted hearing protectors, V-Gard Face Protection Care & Maintenance System, Winter Liners, and chinstraps • Clean helmet assembly regularly with MSA's Confidence Plus PRODUCT DIMENSIONS 12.12" x 10.5" x 6" Cleaning Solution (P/Ns 10009971 or 10032737) or mild soap .94 lb (no detergents) and warm water MIN ORDER QUANTITIES 20 (stocked colors) (MOQ) 100 (non-stocked colors) • Do not throw, drop, use as support or abuse helmet 500 (custom colors) to ensure proper working condition SHIPPING CARTON 25" x 21.75" x 14.5" • Store helmet in clean, dry environment <49°C (120°F). DIMENSIONS (BOX OF 20) 23.8 lb

Service Life Guidelines Technical Assistance/Additional Information • V-Gard Helmets are made with high-quality, For more information about V-Gard Helmets and other MSA products, wear-resistant materials please contact MSA Customer Service at 1-800-MSA-2222 • Inspect the helmet before and after each use and replace or visit MSAsafety.com. any part(s) as required MSA – The Safety Company MSA Canada • Always replace the helmet after it has withstood an impact 1000 Cranberry Woods Drive Phone 1-800-672-2222 Cranberry Township, PA 16066 USA Fax 1-800-967-0398 or penetration. MSA recommends: Phone 724-776-8600 – replacing the suspension after no more than 12 months of use www.MSAsafety.com U.S. Customer Service Center – replacing the shell after no more than five (5) years of use Phone 1-800-MSA-2222 Fax 1-800-967-0398 • Please consult user instructions for additional details

ID 0613-69-MC / July 2015 © MSA 2015 Printed in U.S.A. Because every life has a purpose... RED WING SHOES INDUSTRIAL SALES

8241 RED WING MEN'S 9-INCH PULL-ON BOOT BROWN

Electrical Hazard Steel Toe

Puncture Resistant

LEATHER TYPE: Full Grain, Water-Resistant LEATHER NAME: Brown Boomer Leather CONSTRUCTION: SuperSole® Welt INSOLE: Texon® SHANK: Fiberglass LAST: 522 OUTSOLE: Mini Lug SuperSole® - Black

NON-MARKING: Yes COUNTRY OF ORIGIN: Made in USA SAFETY RATING: ASTM F2413-11, M I/75 C/75 PR CARE PRODUCTS: Boot Oil,Leather Protector SIZES: EE5-12,13,EEE6-12

SLIP RESISTANCE GOOD OIL/GAS RESISTANCE BEST CHEMICAL BETTER RESISTANCE BETTER ABRASION RESISTANCE MINI LUG SUPERSOLE® - BLACK

2-Channel Precision Direction Finder RT-202

Compact and Easy to use

The RT-202 CrewFinder features compact, robust design the person in distress. The “selective squelch” function and permits fast, effi cient recovery in the event of a prevents false alarms caused by interference or other man overboard incident despite heavy seas and poor radio signals. The RT-202’s compact antenna also makes visibility. The RT-202 monitors the 121.5 MHz inter- it ideal for installation on smaller vessels and lifeboats as national distress frequency and alarms the crew if an well as for landside applications. emergency signal is received. The bearing of the source is shown on the LED screen to lead the crew directly to SAR (Search and Rescue) and “Man over- The transmitter is activated either manually or through board” applications immersion in water. This triggers transmission of a signal on the international emergency frequency (121.5 A “man overboard” emergency is always terrifying – for MHz). The azimuth of the source of the signal is then the person in distress as well as for crew members. Un- automatically displayed on board the vessel to within der poor conditions, it can be almost impossible to fi nd ±10°, and a loud acoustic signal is triggered at the same someone in the water and whether or not the individual time. This enables the skipper to turn the vessel in the is found is a matter of luck. To make matters worse, direction of the source of the signal to approach the search and rescue services are usually not available due individual in the water. Since the direction fi nder oper- to the lack of a seamless infrastructure or SAR person- ates over 360° azimuth, the signal cannot be lost while nel cannot reach the person in the water before it is too maneuvering. late. The RT-202 makes it possible to reach and rescue overboard crew members quickly and easily despite adverse weather and water conditions.

All crew members are equipped with personal locator beacons (PLB), which can be either attached to their life jackets or worn on their person.

The RT-202 CrewFinder is a robust, easy-to-operate MOB rescue device that is ideal for use on virtually all vessels or offshore installations. Electrical data

Method of bearing: Doppler principle (3 kHz frequency of rotation) Bearing accuracy1: ±5° Internal resolution: 1° Sensitivity: < 2 µV/m Reception frequencies: 121.500 MHz + 121.650 MHz (customer-specific frequencies available on request) Bearable modulation: A3E, F3E, A3X (distress modulation), bearing largely independent of modulation Polarization: Vertical Polarization error: < 5° at 60° field vector rotation Garbling cone: Approx. 30° to the vertical Response time2: < 50 ms (with sufficient reception field strength) Operating voltage: 12 V to 28 V DC Power consumption: Max. 350 mA (without external speaker) Monitoring: With built-in miniature speaker, modulation: A3E

Interfaces

Serial RS-232 (V24): 1200 baud, parity = odd, 7 data bits, 1 stop bit

Audio out: For external loudspeaker (on GND) approx. 5 Vpp on 8 Ω, output power approx. 0.5 W Alarm out: Open collector output to GND with reception signal / alarm:

Uout < 1.0 V DC (Imax: approx. 100 mA)

Mechanical data

Operating temperature: -20 °C to +60 °C Weight: Display Control Unit (DCU): approx. 600 g Antenna Unit (AU): approx. 1400 g Dimensions: DCU: length x width x height 120 mm x 100 mm x 55 mm AU: diameter x height 260 mm x 600 mm Ingress protection: IP 67 (The use of the mast sealing kit is recommended to protect the antenna connector against moisture.) Lateral thrust due to Approx. 14 N at 150 km/h wind speed wind: Approx. 20 N at 180 km/h wind speed

1 With undisturbed wave field and sufficient field strength. Measured by changing the angle of incidence with the antenna rotating on a revolving table in order to eliminate environmental influences on the results. 2 Very weak signals can increase response time considerably! www.rhotheta.com

Features

• Completely automatic operation • Compact and robust construction ensures • Very high receiver sensitivity to permit detection exceptional reliability of very weak or remote signals • All DF components are waterproof (IP 67) • Bearing information displayed on a circular LED • Easy to install: no RF cables required direction indicator • Interface for remote operation and data transfer • Selective alarm function to prevent false alarms to a PC • Signal strength indicator

��

POM housing (standard) Aluminum housing with panel mounting brackets

��

Screw ﬂange (standard) 6-hole-ﬂange

All product speciﬁcations subject to change without notice.

RHOTHETA Elektronik GmbH Dr.-Ingeborg-Haeckel-Str. 2 82418 Murnau E-Mail: [email protected] Germany Internet: www.rhotheta.com

Tel.: +49 8841 4879 - 0 Coordinates: Fax: +49 8841 4879 - 15 N 47.6842° / E 11.1982° / (WGS 84)

BRAND NAME: Imperial DESCRIPTION: 198RT, 199RT Offshore PFDs

PRODUCT • USCG Type I Approval 160.055/153/0 FEATURES • International Safety Orange color AND NOTES: • PE (Polyethylene) foam buoyancy • 1” stainless steel snaphook and d-ring closure • Two 1" encircling straps and one 1" neck strap • 126 square inches of SOLAS-grade reflective tape • Reversible design for quick donning • Weather- and fade-resistant polyester • Light loop and whistle attachment over shoulder --- Box/case package dims/weight/unit qty by PFD size: --- • 198RT: 32x21x21", 17 lbs, qty of 8 units enclosed • 199RT: 22x20x17", 10 lbs, qty of 8 units enclosed

SPECIFICATIONS

DIMENSIONS UPC-A UNIT COUNTRY OF WEARER WEARER MINIMUM LIFEJACKET SIZE PRODUCT # (LxWxH) BARCODE WEIGHT ORIGIN WEIGHT CHEST SIZE BUOYANCY

198RT (adult) 6x15x19" 098198363069 1.4 lbs 61-198RT-001 China >90 lbs up to 60" 24 lbs (107N) 199RT (child) 5x11x15" 098198373068 1.35 lbs 61-199RT-001 China <90 lbs Call 16 lbs (71N)

Survitec Group Survitec Survival Products, Inc. 1420 Wolf Creek Trail, PO Box 545, Sharon Center, OH 44274 Tel: 330-239-4331 / Fax 330-239-3671 / Email: [email protected] www.survitecgroup.com

SCD0006A REV12222015 PAGE 1 OF 1

SEACREWSADER 275N SOLAS 275N INFLATABLE LIFEJACKET

The Seacrewsader 275N Twin is designed to SOLAS 2010 regulations, and outperforms the new requirements to provide increased performance in the most demanding environments. Improved body angle, mouth freeboard and face plane angles make the Seacrewsader even safer at sea. Together with the improved rotating times each chamber is fitted with two 60 g CO2 cylinders, activated by UML MK5i standard automatic inflation mechanisms* - and a 3.5 psi relief valve to ensure full buoyancy during single or double chamber inflation.

The Seacrewsader 275N Twin is designed for extreme working environments and is also suitable for abandonment purposes. The high buoyancy level provides added protection when heavy work gear and clothing is worn. The new, more compact cover is a robust fabric to withstand the most arduous conditions without damage to the lifejacket and internal bladders. Crotch straps come fitted as standard.

FEATURES • TWIN CHAMBER 275N MSC 200 (80)/ SOLAS APPROVED LIFEJACKET • HIGH BUOYANCY LEVEL PROVIDES ADDED PROTECTION WHEN HEAVY WORK GEAR AND CLOTHING IS WORN • SUITABLE FOR USE WITH MOST IMMERSION AND ABANDONMENT SUITS, SUBJECT TO COMPATIBILITY TESTING. • ONE SIZE FITS ALL ADULT SIZE • ALSO AVAILABLE IN HAMMAR INFLATION (SEE CREWFIT TWIN CHAMBER CODES)*

“The cover is available as standard in durable PU coated polyester, it is also available with a wipe clean or fire resistant cover. SEACREWSADER 275N

Oral/relief tubes Spray hood TECHNICAL DATA

Newtons 275N Whistle Oral/relief tubes Type Lifejacket Flotation Inflatable Lifting becket Chambers Twin

Harness Fall Arrest / Deck Optional CSL light Heavy Duty, Fire Retardant Cover or Wipe Clean

Approval MED / SOLAS Buddy line Reflective tape

Twin UML automatic inflator

Accessories

PRODUCTS

Product Number Product Name

SUPFITS20 McMurdo S20 Supply and Fit

Spares Ordering Information

PRODUCTS PRODUCTS

Product Number Product Name Product Number Product Name

1143-AUTO Seacrewsader 275N Twin Chamber Automatic with Hood 11037 60 g CO2 Cylinder for 290N Lifejackets x 2 Seacrewsader 275N Twin Chamber Automatic Fall Arrest Harness 1143-PLUS 10017 Mk5i Black Automatic Capsule with Hood

12050 60 g CO2 Cylinder for Manual and Automatic 1143-AUTOH Seacrewsader 275N Twin Chamber Automatic Hood and Harness 1154-HAMM Crewfit 275N Twin Chamber Hammar with Hood

1154-H&H Crewfit 275N Twin Chamber Hammar with Hood and Harness APPROVALS Crewfit 275N Twin Chamber Hammar with Hood and Fall Arrest 1154-PLUS The Seacrewsader 275N Twin inflatable lifejacket is approved to Harness SOLAS MSC 81(70) as amended by MSC 200(80) and MSC 207(81)

GET IN TOUCH www.survitecgroup.com Phone +44 (0)1329 820 000 Survitec House, Lederle Lane, Gosport, Hampshire, Email [email protected] PO13 0FZ, United Kingdom