sign in sign up
<<
Home , Paint

PERFORMANCE BY DESIGN TM TECHNICAL BULLETIN OSB And The Humid Environment PRODUCT OVERVIEW cured during the high tempperature pressing process which brings the components together to form a Oriented Strand Board (OSB) is an engineered structual very stable, insoluble, waterproof and boilproof panel. OSB is made by processing small diameter, connection between the OSB strands making up the fast growing trees into thin strands which are bonded panel. Interior type binders are slowly soluble in water and are primarily for interioruse such as wall together under heat and presure with an exterior resin paneling, cabinets and furniture. binder. OSB is manufactured to a performance standard which identifies the structural and physical performance, BOND CLASSIFICATION fastener holding and bond durability requirements needed for a particular end-use, or All trademark stamps must state the panel’s Bond alternatively but less frequently to a product standard Classification. This classification is a designationof the which specifies the minimum mechanical and physical moisture resistance of the glue bond and is related to the properties for the grade. intended end use. It is a function of the structural panel’s raw material composition and its adhesive bond WOOD & MOISTURE durability. OSB panels intended for construction are marked Expoure 1, in accordance with the US-DOC All wood products naturally contain water. In fact, the Voluntary Product Standard PS2, or Exterior Type Bond natural moisture content in wood can vary from 25 in accordance with Canadian Building Codes. percent to more than 200 percent. In the process, most of that natural moisture content is removed. EXPOSURE 1 With OSB, wood strands cut from green wood are typically dried to between three to eight percent moisture content. the Exposure 1 Bond Classification indicates continued The wood strands are then coated with powdered or performance where delays in construction may cause the and a small amount of . These resin binders panels to be exposed to the weather before being together with the wax will contribute to OSB’s moisture protected. Like CDX , OSB panels with this resistant qualities. However, like alll wood products, OSB designation are intended for protcted construction uses will react to change in moisture and humidity in service. not permanently exposed to the weather, intended to resist moisture exposure due to construction delays, or EXTERIOR-TYPE RESIN BINDERS other conditions of similsr severity. OSB panels marked resin binders used for construction products are generally Expoure 1 must meet specific (i.e. moisture cycling) bond of two types, Exterior for use under conditions exposed requirements. to humid weather or high humidity and Interior for use under dry humidity levels.Exterior type resin binders are

® Structural Board Association Representing the OSB PANEL CERTIFICATION JOBSITE CARE OF OSB OSB panels intended for construction will bear With all wood products, care should be taken to avoid the stamp of an accredited third party testing and contact with free moisture. Because this is not always inspection agency. Principle agencies include APA – possible, especially in the early stages of construction, The Association, TECO Corp. and the Structural Board Association recommends the PSI/PTL Inc. The trade mark includes nominal following precautions to minimize the effects of thickness, span rating, bond classification, the symbol moisture on OSB: PS2, the name or logo of the testing agency and the • If heavy rainfall or melting snow comes in contact manufacturer’s name. with OSB floors, it is recommended that all MOISTURE PROTECTION moisture be removed by shoveling, sweeping, etc. OSB panels are edge-coated with a proprietary water • If ponding occurs, holes should be drilled in the resistant sealer to reduce edge swelling. If needed, affected areas to drain the water. panels should be cut to preserve as much of the edge • If OSB floors are exposed to prolonged moisture as possible. Remaining panel edges that may be during construction, it may be necessary to exposed to moisture should either be protected or the edges and surface slightly to remove any high coated with an exterior latex paint. When panels are to spots. be exposed to the weather such as the exterior walls of carports, garden sheds, or fascia boards, they should be • Prior to installation of the floor covering the OSB painted or stained. Panels intended for should subfloor should be dry and thoroughly swept or be primed with a good quality ; panels that will vacuumed to remove any dirt or debris remaining be stained, should be treated with a water-repellent from the construction. primer compatible with the stain finish. When using OSB as roof sheathing, it is recommended VAPOR BARRIERS FOR FLOORING that the roofing materials – felt, shingles, shakes, etc. – be installed as soon as possible after completing the Although OSB floor sheathing panels have low moisture sheathing installation. For larger flat roofs, built-up a permeability, local building codes may require the use roofing materials should be placed in sequence as the of a vapor barrier on the underside of the panel. If so, sheathing installation progresses. consult with the local building inspector or flooring manufacturer as to the type and method of When using OSB as wall sheathing, under siding or installation. stucco, protect the panels by installing good quality sheathing paper or sheathing membrane over the panels SHIPPING, HANDLING & STORING prior to placing the siding or stucco. Pay particular Reasonable care is required in warehousing and storage attention to wrapping the sheathing membrane around of OSB, especially on the job site, to protect panels from the edges of all openings. mechanical damage and lengthy exposure to adverse moisture conditions. For best results, handle panels as REMINDER little as possible. Ship and store in the original units, if Please remember to gap OSB panels when used as roof, possible. Use care in handling the panels to avoid wall and floor sheathing. These recommended gaps of 1 damaging corners and edges. Store OSB panels produced ⁄8" must also be left around all openings. Also keep OSB by SBA mills indoors or under cover with enough panels a minimum of eight inches above grade when support so that panels remain flat. Provide air installed as wall sheathing. circulation around panels by keeping covers open and away from sides and bottoms of units. Make sure to elevate panels above ground and standing water.

25 Valleywood Drive, Unit 27, Markham, Ontario, Canada L3R 5L9 Member of the Tel: (905) 475-1100 • Fax: (905) 475-1101 Wood Panel Bureau Web: http://www.osbguide.com Email: [email protected] Member of the Sustainable Certification Coalition Printed in Canada EL812