University of Technology/Baghdad/Iraq Email:[email protected] Cell phone: +964 07706328991 Assist. Prof. Dr. Eng. Alaa Abdulhasan
Atiyah
Objective Training Course in Advanced Materials Engineering Born Date Iraq/1968
Education & 1993–1995 Lecturer Engineer University of Technology/Baghdad Experience Lecturer Engineer I was graduated from the Military College of engineering /Baghdad as a first student in the Aircraft Mechanical Engineering Department. Labs lectures in practical applications of many experiments in the advanced materials labs to the students of College and Engineering College/ Al-Nahrain University. Participate in many training courses in mechanical engineering and aeronautics engineering. Installation of many labs in the field of mechanical Engineering inside the College.
1995-1998 MSc. Student MCE/Baghdad MSc. Student During these two calendar years I ve got my MSc. Degree in the Metallurgical Engineering/Aircraft Materials Engineering. My MSc. Thesis entitled {Optimization of mechanical properties and fracture toughness of 2024 Aluminum alloy by Thermomechanical Treatments}, under the supervision of the Assistant professor Dr. Eng. Faiq A. Al-Beidhany (BSc. From USA and PhD. In Metallurgy from Manchester University, UK). My work completely done inside the Al-Rasheed College of engineering and science / University of Technology/Baghdad labs and funded from the Iraqi Air ways company.
1998-2001 Member of staff in Military College of engineering /Baghdad
/Baghdad Member of staff : Many courses to the undergraduate students of College in the following subjects: Materials strength, Stress analysis, Metallurgy, Production Engineering, Industrial Engineering, Phase Transformations in Metals and alloys, Heat treatments, Metallurgical Thermodynamics and Statistics. Course of Production Engineering in the College of Engineering/ University of Babylon.
1
A course of Industrial Engineering and Quality Control Engineering in the Technical College/ Baghdad. Consultant Engineer in many industrial institutes and companies inside Iraq. Participate in many activities in the MEC and many Universities inside Iraq.
2001-2005 PhD. Student University of Technology PhD. Student During these three calendar years I've got my PhD. Degree in the Mechanical Engineering/ Metallurgical Engineering My work is under the following title {Study the effect of increasing zinc Percentage on the properties of Al-Zn-Mg alloys and its response to Thermomechanical Treatments}. I ve got (Very Good) evaluation (83.5%) in courses and (very good) evaluation in Theses.
2005-2006 Member of staff University of Technology Member of Staff Senior lecturer in the Materials Engineering Department/University of Technology. Giving a course of Phase Transformations in Metals and Alloys to the postgraduate students in the Materials Engineering Department/University of Technology. A course of Phase Transformations in Metals and Alloys to the postgraduate students in the Materials Engineering Department/University of Babylon. Supervising on the three students of Master of Science in the Materials Engineering in the University of Babylon. Director of Postgraduate studies in the Materials Engineering Department/ College of Engineering/University of Babylon. Senior Consultant Engineer in Al-Maisarah Group of Construction Companies. Design and Supervising of Many Projects in the field of mechanical and materials engineering.
2006-2008
Head of Metallurgical Engineering Department/College of Materials Engineering/University of Babylon Giving lectures in the Materials Engineering Department/University of Babylon. Courses to the postgraduate students: Phase Transformations in Metals and Alloys to the postgraduate students in the Materials Engineering Department/University of Babylon. Advanced physical metallurgy. Mechanical behavior of materials. Supervising on many students of Master of Science in the Materials Engineering in the University of Babylon.
2
Senior Consultant Engineer
2008 until now: Assistant Professor in the department of materials engineering/University of Technology - Baghdad Giving lectures in the Materials Engineering Department/University of Technology. Giving a courses to the postgraduate students such as: Solidification of Metals and Alloys course to the postgraduate students in the Materials Engineering Department/University of Babylon. Advanced Mathematics to the PhD. Students in the materials engineering department/University of Technology. Giving a Failure Analysis course to the undergraduate students: Supervising on three students of Master of Science in the Materials Engineering in the University of Babylon. Senior Consultant Engineer in Al-Maisarah Group of Construction Companies.
Published Papers (Recent Publications) 1. Experimental study of high temperature creep resistance development of Alumina-based fibers by heat treatments. (Journal of Technology/Baghdad, Vol. 5, No. 2) 2. An Experimental study of clearance width effects on the strength of carbon steel brazed joint .(Journal of King Abdul-Aziz University/ Saudi Arabia Kingdom, vol. 8, no. 1, 2007) 3. Effect of Thermomechanical treatments on the aging behavior of Al-Cu-Mg alloy plates used in Aircraft structure (Journal of Materials and Mechanical Engineering/Iraq, 2006). 4. Effect of heat treatment on thermal conductivity and mechanical properties of brake rotor material (Journal of Materials and Mechanical Engineering/Iraq, 2008). 5. Unidirectional solidification of (Al-Si) eutectic alloy (Journal of Materials and Mechanical Engineering/Iraq, 2008). 6. Improvement Anti-oxidation properties of alpha-brass alloy by Aluminum addition (University of Babylon Journal of science/Iraq, 2009). 7. Preparation and evaluation of Al-Ceramic Functionally graded Materials (Journal of Materials and Mechanical Engineering/Iraq, 2010). 8. An investigation of Cadmium Addition effects on aging behavior of Al- Cu alloy. (Journal of Technology/Baghdad, 2010) 9. Cathodic protection of Oil pipe lines by Aluminum alloys. .(Journal of King Abdul-Aziz University/ Saudi Arabia Kingdom, 2010) 10. Calculations of heat affected zone width & characteristics in high carbon steel weldements. (University of Babylon Journal of science/Iraq, 2010). 11. Experimental Study of the failure in Al-Musaib power station boiler pipes (under publication). 12. Preparation of high order (Ni/Cu) functionally graded materials (under publication).
3
Supervision on Following is a list of the researches titles accomplished under my supervision: postgraduate 1. Unidirectional solidification of (Al-Si) in situ composite (MSC research students 2008).
2. Cathodic protection of oil pipe lines by Al alloys (MSC research 2008).
3. Preparation and characterizations of SiC/Al functionally graded materials(MSC research 2009).
4. Preparation and characterization of continuously formed metal/metal functionally graded materials (MSC research /continuous).
Thanks
Signed Dr. Eng. Alaa Abdulhasan Atiyah Assistant Professor Materials Engineering Department University of Technology-Baghdad-Iraq
4