Installation Guide Theniss3h T Firmware for DBALL 2 Is an All-In-One Door Lock and Override Module Compatible with Specific Infiniti, and Nissan Vehicles
Total Page:16
File Type:pdf, Size:1020Kb
Platform: DBALL2 Firmware: NISS3HT Remote Start Ready(RSR) Installation Rev.: 20170817 Update Alert: Firmware updates are postedon the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide TheNISS3H T firmware for DBALL 2 is an all-in-one door lock and override module compatible with specific Infiniti, and Nissan vehicles. This guide supports the installation of aDBALL 2 in Remote Start Ready (RSR ) mode with or without a Plug & Play THNISS3/THNISS3D T-Harness ( o ptional) . This solution offers three (3) configuration options to control your system: 3xOEM Lock Remote Start Activation,RF System or SmartStart (all sold separately). This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer tothe Module Programming sectionon page 11 for more information. Remote Start Ready (RSR ) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or anOEM remote starter in order to start the vehicle from a distance. Important! This product isNOT compatible with vehicles equipped with a manual transmission. Index Vehicle Application Guide .....................................................................................................................................................02 Installation(Wiring Diagram s & Vehicle Wiring Reference Chart s ) Type 1 Wiring Diagramwith T-Harness THNISS3/THNISS3D .............................................................................................03 Type 1 Wiring Diagram without T-Harness ...........................................................................................................................04 Type 2 Wiring Diagram without T-Harness ...........................................................................................................................08 SmartStart/XL202 Installation Notes.....................................................................................................................................10 Module Programming Module Programming............................................................................................................................................................11 Module Reset........................................................................................................................................................................13 HardReset ............................................................................................................................................................................13 Feature & Option List............................................................................................................................................................14 Feature Programming...........................................................................................................................................................14 LED Diagnostics & Troubleshooting.....................................................................................................................................15 Parking Light Error Codes ....................................................................................................................................................17 Limited One-Year ConsumerWarranty .................................................................................................................................18 Quick Reference Guide ........................................................................................................................................................19 SmartStart Compatible SmartStart is equipped with D2D , which means it can be connected to an interface module and used in Remote Start Ready (RSR ) mode without the use of a remote starter. See theModule Programming section for more information. ® Infiniti and Nissanare registered trademarks and property of their respective companies . © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: NISS3HT Remote Start Ready(RSR) Installation Rev.: 20170817 Page 2 Vehicle Application Guide The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles 2017 2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEMRS-3x remote LOCK START (Start control usingRS-3x OEM LOCK Remote) STOP (Stop control usingRS-RAP OEM Shut Remote) Down (Retained ACC Power) RS-Remote Start Ready RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-Door Locks Status Infiniti EX35(SmartKey) 11111 ••••••••••••••• EX37(SmartKey) 11111 • • ••••••••••••• FX35(SmartKey) 1111 ••••••••••••••• FX50(SmartKey) 11111 • • ••••••••••••• G25(SmartKey) 11 ••••••••••••••• G35 (Smart Key) 11 ••••• ••••••••• G37(SmartKey) 111111 • • ••••••••••••• M35 (Smart Key) [1] 22222• • ••••••••••••• Q60(SmartKey) 11 ••••••••••••••• QX50(SmartKey) 1111 • • ••••••••••••• QX70(SmartKey) 1111 • • ••••••••••••• Nissa n 370Z (Smart Key) 11111111 • • ••••••••••••• Altima(SmartKey) 1111 ••••••••••••••• Altima(SmartKey) 11 ••••• ••••••••• Altima Coupe (Smart Key) 1 • • ••••••••••••• GT-R(SmartKey) 11111 • • ••••••••••••• Maxima(SmartKey) 111111 • • ••••••••••••• Murano(SmartKey) 111111 • • ••••••••••••• Legend: AV: Horn & Lights Controls RS: Remote Start & Engine Controls DL: OE Door Lock & Alarm Controls SS: Integrated Security & Monitoring FOB: Sync CAN Interface w/ FOB Remote ST: Function/Feature Status PK: Transponder & Immobilizer Override [1] Special programming required (see Module Programming section). It is also NOT COMPATIBLE with the optional T-harness THNISS3/THNISS3D. © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: NISS3HT Remote Start Ready(RSR) Installation Rev.: 20170817 Page 3 Important! - TheHood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL . - Always connect OBDII connectorBEFORE all other connections. - Parking lightoutputMUST be controlled through data when using T-Harness, see Feature & Option List section to enable this feature. NOT USED Hood Pin T-02 T-02 Note: hood pin only required on vehicles not equipped with a factory hood pin. White/Black T-01 T-01 Remote Start Safety Override Switch ConnectorsT-01 and T-02 (each pair has one male and one female) are NOT 14 12 interchangeable, thus you will be able to connectONLY the Key Port connector correct connectors. (-)RAP Off Output: Red/Black 10 Refer to the (-) Push-To-Start Output: Green/Black Vehicle wiring reference Push-to-Start Chart. (Brown conn, at Push-to-Start switch) 132 2 RF 4 567 8 4 Prog. Button (-) Push-To-Start: pin 4 LED DBALL2 T-Harness THNISS3/ THNISS3D NOT USED B-01 B-02 You can connect to either aXL 202 RFTD OR a SmartStart module. Refer to the OR SmartStart/XL 202 OBDII Installation Notes for Brake Pedal Diagnostic16-pin Connector more information. (connector side view) 1 8 9 16 © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: NISS3HT Remote Start Ready(RSR) Installation Rev.: 20170817 Page 4 Type 1 Wiring Diagram without T-Harness Important! TheHood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL . Diagnostic Conn. OBDII (connector side view) HS CAN High: pin 6 18 9 16 Push-to-Start HS CAN Low: pin 14 (Brown conn. at Push-to-Start switch) Note: The installation of an aftermarket hood pin (sold 132 separately) is only required 4 567 8 on vehicle not equipped (-) Push-to-Start: pin 4 HS CAN High:Tan/Black: 3 with a factory hood pin. HS CAN Low:Tan: 4 Immo.Data Interr. (Vehicle side):Yellow: 8 Hood Pin 14 12 Immo.Data Interr. ( conn. side):Orange/Yellow: 9 (+) 12V (+) 12V Input:Red: 13 (-) Ground:Black: 14 (-) Push-To-Start Output:Green/Black : 2 Remote Start Safety Override Switch (-)RAP Off Output :Red/Black: 4 (+) BrakeActivation Output :Gray: 6 10 6: White/Black: (-) Hood (+)Keysense Output :Gray/Black: 7 Immo. Clock Output:Yellow/Black: 10 Immo.Data Output (veh . side):Orange /:Black 11 (+) 12V (fused) 2 RF 4 8687 85 Prog. Button 87a 30 LED DBALL2 Clock, Data & Keysense (white conn. at key port) Refer to the Vehicle Clock: pin 2 wiring reference Chart. 1 2 3 4 5 6 You can connect to either 7 8 9 101112 aXL 202 RFTD OR a SmartStart module. CUT Data: pin 3 Refer to the SmartStart/XL202 (+) Keysense: pin 11 Key Port connector Installation Notes for more information. BCM conn. (Green connector in passenger kick panel or behind cluster) Note: insert pin if wire is not present 20 19 18 17 16 15 14 13 12 11 10987654321 40 39 38 37 36 35 34 3332 31 30 29 28 27 26 25 24 23 22 21 (-) Driver Door Trigger (RAP Off): pin 39 With the exception of theOBDII Diagno s tic connector, all adapters are displayed from the wire side (unless specified otherwise). © 2017 Directed. All rights reserved. Platform: DBALL2 Firmware: NISS3HT Remote Start Ready(RSR) Installation Rev.: 20170817 Page 5 Type 1 - Vehicle Wiring Reference Chart Wire Information Connector Information Function Color Pin Polarity Location Color Pins Infiniti EX35 (Smart Key)