City & Co. of San Francisco Public Safety Uniforms, Accessories

City & Co. of San Francisco Public Safety Uniforms, Accessories, Equipment Contract Proposal No. 81150 Purchasing Department Appendix C Aggregate #1 Items 1- 205 POLICE ITEMS SPECIFICATIONS San Francisco Police Dept.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

1 SHIRTS-LONG SLEEVE, MALE Flying Cross by Fechheimer 20W9586

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC Raeford Only: #8321-30

Content: 100% Wool Tropical Weave conforming to the following specifications:

Weight: 10-10 1/2 oz. per linear yd.

Construction: 50 ends/46 picks per inch.

Tensile: Warp 55 lbs. Filling 50 lbs. COLOR LAPD Navy matching standard of Raeford's 30 Shade.

STYLE The style shall be known Dress style, top center placket front, full cut tapered fit, banded collar, long sleeves with square cuffs, and dress shirttail. Two plain breast pockets with topstitched scalloped flaps. Topstitched shoulder straps. Exterior badge holder with metal eyelets. Matching inside yoke and band of high luster Poly Twill. Work wear industrial style shirt construction is unacceptable and shall be cause for rejection. COLLAR & STAND Collar points to measure 3” long with ultrasonically fused-in or SEWN-IN Mylar stays. Stays to be 2-3/4” long, 3/8” minimum width, and to be fused to under side of collar interlining. Stays applied directly to collar material itself unacceptable. There shall be a ¾” tie space opening when collar band is buttoned. Collar height at rear 1-1/2". Collar topstitched with ¼” Double Needle Stitching. Collar band shall have 2 (two) rows of stitching ½” apart. Collar stand to measure 1-5/16" at rear and band to be interlined with "Crease-N- Tack." Collar material itself (top or underside) shall have no fusing to Mylar stays or collar interlining. Collar to have woven interlining of #285 Stabilized Mello-Press.

FRONT: The left front shall have a top center placket 1 ¾” wide with two double rows of stitching. The shirt will have 7 buttons and buttonholes on the front; spacing between each will be 3 ¾” except the spacing between the neck button and the first button on the front, which will be 3 ¼”. Top center placket to have woven interlining of #550 Stabilized Mello-Press. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a ¼” double needle stitch. Safety stitch joining unacceptable. EPAULETS Shoulder straps to be two-piece pointed, 1/4” double needle topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1-3/8" and set not more than 1/2" from collar set seam. Cross & box stitched 2" from sleeve seam. Shoulder strap to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable. BADGE REINFORCEMENT Exterior badge piece is to finish 1 1/8" wide x 2 1/4" long with two black metal eyelets. Centered 1 3/4" above left flap and eyelets spaced 1 1/4" apart.

POCKETS Shirt is to have two plain breast pockets with rounded corners Pocket to measure 5-5/8" wide, 6" deep. Breast pockets are set to shirtfront with ¼” double needle stitching. Left breast pocket to have 1- 1/2" pencil stitch. Each pocket to have hook Velcro, 3/4" long by ½" wide, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement.

FLAPS Two piece deep scalloped design to measure 5 7/8" across and 2-3/4" in depth at center point, 2-1/4" at sides. Secured to shirtfront 3/8” above pocket. Left flap to have invisible pencil opening 1-1/2" to correspond precisely with pencil slot of pocket. (Stop & start stitching for pencil opening unacceptable and shall be cause for rejection.) Flaps to be 1/4" double needle topstitched. Flaps to have woven interlining of #550 Stabilized Mello-Press. Creased and edge stitched pocket flap construction unacceptable. Under side of the flap to have looped Velcro 3/4" long by 1/2" wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket. Each flap shall have a button centered on uncut sewn buttonhole. SLEEVES & CUFFS To be long sleeves cut straight and whole, with 5 1/2"sleeve vent. Sleeve shall have a one-piece, elbow reinforcement and vent facing. Elbow reinforcement shall extend into the sleeve-closing seam. Lower facing shall measure 1/2" in width. Cuff to measure 3" with square corners. There shall be two buttons with corresponding buttonholes on each cuff and one button and buttonhole in the sleeve facing. Cuffs to be interlined with Durapress #550.

BUTTONS First grade 24-ligne melamine to match.

STICHING Entire shirt is to be double stitched 1/4" apart THREAD All sewing threads to be fast color polyester core polyester wrap to match.

INTERLININGS: Collar shall be interlined with #285 Stabilized MelloPress. Cuffs, pocket flaps, shoulder straps and top center to be interlined with #550 Stabilized MelloPress. Collar band interlining to be Crease-N-Tack. CONVERTIBILITY This garment shall be designed to accommodate removable metal buttons having eyelets under the sewn buttons on the shoulders and the pockets. Protective pieces shall be sewn on the inside of the garment on the shoulders.

CONSTRUCTION Collars, cuffs, flaps and shoulder straps are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

2 SHIRTS-LONG SLEEVE, FEMALE Flying Cross by Fechheimer 120W9586

SPECIFICATIONS AND ESSENTIAL FEATURES

FABRIC Raeford Only: #8321-30

Content: 100% Wool Tropical Weave conforming to the following specifications:

Weight: 10-10 1/2 oz. per linear yd.

Construction: 50 ends/46 picks per inch.

Tensile: Warp 55 lbs. Filling 50 lbs. COLOR LAPD Navy matching standard of Raeford's 30 Shade. STYLE The style shall be known Dress style, top center placket front, full cut tapered fit, banded collar, long sleeves with square cuffs, and dress shirttail. Two plain breast pockets with topstitched scalloped flaps. Topstitched shoulder straps. Exterior badge holder with metal eyelets. Matching inside yoke and band of high luster Poly Twill. Work wear industrial style shirt construction is unacceptable and shall be cause for rejection.

POCKETS Shirt is to have two plain breast pockets with rounded corners. Pocket to measure 5-3/8" wide, 5-1/2" deep. Breast pockets are set to shirtfront with ¼” double needle stitching. Each pocket to have hook Velcro, 3/4" long by ½" wide, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement.

FLAPS Two piece deep scalloped design to measure 5 5/8" across and 2-1/4" in depth at center point, 1-3/4" at sides. Secured to shirtfront 3/8” above pocket. Left flap to have invisible pencil opening 1-1/4" wide. (Stop & start stitching for pencil opening unacceptable and shall be cause for rejection.) Flaps to be 1/4" double needle topstitched. Flaps to have woven interlining of #550 Stabilized Mello-Press. Creased and edge stitched pocket flap construction unacceptable. Under side of the flap to have looped Velcro 3/4" long by 1/2" wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket. Each flap shall have a button centered on uncut sewn buttonhole. COLLAR & STAND Collar points to measure 2 7/8” long with ultrasonically fused-in Mylar stays. Collar to have woven interlining of #285 Stabilized Mello-Press. Stays to be 2-1/2” long, 3/8” minimum width, and to be fused to under side of collar interlining. Stays applied directly to collar material itself unacceptable. Collar height at rear 1-1/2". Collar topstitched with ¼” Double Needle Stitching. Collar band shall have 2 (two) rows of stitching ½” apart. Collar stand to measure 1-5/16" at rear and band to be interlined with "Crease-N- Tack." Collar material itself (top or underside) shall have no fusing to Mylar stays or collar interlining.

FRONT: The right front shall have a top center placket 1 ½” wide with two double rows of stitching. The shirt will have 6 buttons and buttonholes on the front; spacing between each will be 3 ½” except the spacing between the neck button and the first button on the front, which will be 3”. Top center placket to have woven interlining of #550 Stabilized Mello- Press. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a ¼” double needle stitch. Safety stitch joining unacceptable. SHOULDER STRAPS: Shoulder straps to be two-piece pointed, 1/4” double needle topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1-3/8" and set not more than 1/2" from collar set seam. Cross & box stitched 2" from sleeve seam. Shoulder strap to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable. SLEEVES & CUFFS To be long sleeves cut straight and whole, with 4 1/2"sleeve vent. Sleeve shall have a one-piece, elbow reinforcement and vent facing. Elbow reinforcement shall extend into the sleeve-closing seam. Lower facing shall measure 1/2" in width. Cuff to measure 2-1/2" with square corners. There shall be two buttons with corresponding buttonholes on each cuff and one button and buttonhole in the sleeve facing. Cuffs to be interlined with Durapress #550.

SLEEVES To be long sleeves cut straight and whole, with 5” sleeve vent. Sleeve shall have one-piece elbow reinforcement and vent facing. Elbow reinforcement shall extend into the sleeve closing seam with ¼” double needle topstitch. Lower facing shall measure ½” in width. Cuff to measure 2 ½” with square corners. There shall be two buttons with corresponding buttonholes on each cuff and one button and buttonhole in the sleeve facing. Cuffs to be interlined with #550 Stabilized Mellopress. BADGE REINFORCEMENT Exterior badge piece is to be finished l 1/8" wide X 2 1/4" long with two black metal eyelets. Centered l 3/4" above left flap and eyelets spaced l l/4" apart.

BUTTONS First grade 24-ligne melamine to match. STITCHING Entire shirt is to be double stitched 1/4" apart. THREAD All sewing threads to be fast color polyester core polyester wrap to match. INTERLININGS: Collar shall be interlined with #285 Stabilized MelloPress. Cuffs, pocket flaps, shoulder straps and top center to be interlined with #550 Stabilized MelloPress. Collar band interlining to be Crease-N-Tack.

CONVERTIBILITY This garment shall be designed to accommodate removable metal buttons having eyelets under the sewn buttons on the shoulders and the pockets. Protective pieces shall be sewn on the inside of the garment on the shoulders.

CONSTRUCTION then Collars, cuffs, flaps and epaulets are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, turned right side out, and finally topstitched. STOCK SIZES:

Shirts must be available in the following sizes:

Bust Sizes 28-52

Long Sleeve Lengths:

30 Regular = 30”

32, 34 Regular = 30” Long = 31”

36, 38 Regular = 31” Long = 32”

40, 42 Regular = 32” Long = 33”

44, 46 Regular = 33” Long = 34”

48 & Up Regular = 34” Long = 35”

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

3 SHIRTS-SHORT SLEEVE, MALE Flying Cross by Fechheimer 70R9586

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC Raeford Only: #8321-30

Content: 100% Wool Tropical Weave conforming to the following specifications:

Weight: 10-10 1/2 oz. per linear yd.

Construction: 50 ends/46 picks per inch.

Tensile: Warp 55 lbs. Filling 50 lbs. COLOR LAPD Navy matching standard of Raeford's 30 Shade. STYLE Dress style, top center placket front, full cut tapered fit, convertible collar, short sleeves, and dress shirttail. Two plain breast pockets with topstitched scalloped flaps. Topstitched shoulder straps. Exterior badge holder with metal eyelets. Matching inside yoke and banana band of high luster Poly Twill. Work wear industrial style shirt construction is unacceptable and shall be cause for rejection. COLLAR Collar points to measure 3" long with ultrasonically fused-in Mylar stays. Collar to have woven interlining of #285 Stabilized Mello-Press. Stays to be 2-3/4” long, 3/8” minimum width, and to be fused to under side of collar interlining. Stays applied directly to collar material itself unacceptable. Collar topstitched with 1/4” double needle stitching. Collar material itself (top or underside) shall have no fusing to Mylar stays or collar interlining.

FRONT Each front shall have a facing 3” in width. The left front shall have a top center placket 1-3/4" wide with two double rows of stitching. The shirt will have 7 buttons and buttonholes on the front; spacing between each will be 3-3/4" except the spacing between the neck button and the first button on the front, which will be 3-1/4". Top center placket to have woven interlining of #550 Stabilized Mello-Press. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a ¼” double needle stitch. Safety stitch joining unacceptable. SHOULDER STRAPS: Shoulder straps to be two-piece pointed, 1/4” double needle topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1-3/8" and set not more than 1/2" from collar set seam. Cross & box stitched 2" from sleeve seam. Shoulder strap to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable. BADGE REINFORCEMENT Exterior badge piece is to finish 1 1/8" wide x 2 1/4" long with two black metal eyelets. Centered 1 3/4" above left flap and eyelets spaced 1 1/4" apart.

FLAPS Two piece deep scalloped design to measure 5 7/8" across and 2-3/4" in depth at center point, 2-1/4" at sides. Secured to shirtfront 3/8” above pocket. Left flap to have invisible pencil opening 1-1/2" to correspond precisely with pencil slot of pocket. (Stop & start stitching for pencil opening unacceptable and shall be cause for rejection.) Flaps to be 1/4" double needle topstitched. Flaps to have woven interlining of #550 Stabilized Mello-Press. Creased and edge stitched pocket flap construction unacceptable. Under side of the flap to have looped Velcro 3/4" long by 1/2" wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket. Each flap shall have a button centered on uncut sewn buttonhole. SLEEVES Sleeves are to be straight and whole, to have 3/4" hem and to finish 9 3/4" from shoulder seam. BUTTONS First grade 24-ligne melamine to match.

STICHING Entire shirt is to be double stitched 1/4" apart

THREAD All sewing threads to be fast color polyester core polyester wrap to match. INTERLININGS: Collar shall be interlined with #285 Stabilized MelloPress. Pocket flaps, shoulder straps and top center to be interlined with #550 Stabilized MelloPress. CONVERTIBILITY

This garment shall be designed to accommodate removable metal buttons having eyelets under the sewn buttons on the shoulders and the pockets. Protective pieces shall be sewn on the inside of the garment on the shoulders.

CONSTRUCTION

Collars, flaps and shoulder straps are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

4 SHIRTS-SHORT SLEEVE, FEMALE Flying Cross by Fechheimer 170R9586

SPECIFICATIONS AND ESSENTIAL FEATURES

FABRIC Raeford Only: #8321-30

Content: 100% Wool Tropical Weave conforming to the following specifications:

Weight: 10-10 1/2 oz. per linear yd.

Construction: 50 ends/46 picks per inch.

Tensile: Warp 55 lbs. Filling 50 lbs. COLOR LAPD Navy matching standard of Raeford's 30 Shade.

STYLE Dress style, top center placket front, full cut tapered fit, convertible collar, short sleeves, and dress shirttail. Two plain breast pockets with topstitched scalloped flaps. Topstitched shoulder straps. Exterior badge holder with metal eyelets. Matching inside yoke and banana band of high luster Poly Twill. Work wear industrial style shirt construction is unacceptable and shall be cause for rejection. COLLAR Collar points to measure 2-7/8" long with ultrasonically fused-in Mylar stays. Collar to have woven interlining of #285 Stabilized Mello-Press. Stays to be 2-1/2” long, 3/8” minimum width, and to be fused to under side of collar interlining. Stays applied directly to collar material itself unacceptable. Collar topstitched with 1/4” double needle stitching. Collar material itself (top or underside) shall have no fusing to Mylar stays or collar interlining. FRONT Each front shall have a facing 3” in width. The right front shall have a top center placket 1-1/2" wide with two double rows of stitching. The shirt will have 6 buttons and buttonholes on the front; spacing between each will be 3-1/2" except the spacing between the neck button and the first button on the front, which will be 3". Top center placket to have woven interlining of #550 Stabilized Mello-Press. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a ¼” double needle stitch. Safety stitch joining unacceptable. EPAULETS Shoulder straps to be two-piece pointed, 1/4” double needle topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1-3/8" and set not more than 1/2" from collar set seam. Cross & box stitched 2" from sleeve seam. Shoulder strap to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable.

BADGE REINFORCEMENT Exterior badge piece is to finish 1 1/8" wide x 2 1/4" long with two black metal eyelets. Centered 1 3/4" above left flap and eyelets spaced 1 1/4" apart.

FLAPS Two piece deep scalloped design to measure 5 5/8" across and 2-1/4" in depth at center point, 1-3/4" at sides. Secured to shirtfront 3/8” above pocket. Left flap to have invisible pencil opening 1-1/4" wide. (Stop & start stitching for pencil opening unacceptable and shall be cause for rejection.) Flaps to be 1/4" double needle topstitched. Flaps to have woven interlining of #550 Stabilized Mello-Press. Creased and edge stitched pocket flap construction unacceptable. Under side of the flap to have looped Velcro 3/4" long by 1/2" wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket. Each flap shall have a button centered on uncut sewn buttonhole. SLEEVES Sleeves are to be straight and whole, to have ¾” hem to finish 8 ½” from shoulder seam. BUTTONS First grade 24-ligne melamine to match. STICHING Entire shirt is to be double stitched 1/4" apart THREAD All sewing threads to be fast color polyester core polyester wrap to match.

INTERLININGS: Collar shall be interlined with #285 Stabilized MelloPress. Pocket flaps, shoulder straps and top center to be interlined with #550 Stabilized MelloPress.

CONSTRUCTION

Collars, flaps and epaulets are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched. STOCK SIZES:

Shirts must be available in the following sizes:

Bust sizes: 28-52

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

5 MALE WOOL TROUSERS Flying Cross by Fechheimer Brothers Company SFPDTRS01

WARRANTY: Garment must have one (1) year warranty against manufacturing workmanship and fabric defects

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC Raeford Mills #13507. 19 1/2 to 20 oz/linear yard (60" width) 100% wool elastique two ply warp and filling with a breaking strength of 115 lbs in the warp and 90 lbs in the filling

COLOR DARK NAVY #2135. DESIGN Trouser shall be manufactured from a men's uniform trouser pattern. The trouser styling shall incorporate a plain front and straight leg bottoms. The trouser will have two straight side pockets, two hip pockets, a watch pocket and two club pockets, one below each hip pocket.

POCKET DESIGN The two side pockets will have a minimum opening of 6 1/2" and a minimum depth of 5 3/4" measured from the bottom of the pocket opening. Side pockets shall have straight bartacks at top and bottom of pocket openings Pockets shall be constructed using the stitch, turn, and topstitch method. Pocket facings shall be made of the basic fabric and measure a minimum of 1 1/2" from the bottom of the pocket opening.

The two hip pockets shall have a minimum opening of 6" and a minimum depth of 7 1/2" measured from the bottom of the pocket opening. Hip pockets shall be constructed using the double welt method on a REECE PW machine and the welts shall be finished in such a manner that there is no topstitching (topstitched hip pocket welts shall be cause for rejection). The corners of the hip pockets shall have triangle bartacks for reinforcing strength.

The watch pocket shall be located on the right front. This pocket shall have a minimum opening of 3 1/4" and depth of 4". The front of the pocket shall be made of pocketing fabric and the back of the pocket shall be made of basic fabric and the two pieces are securely stitched together. Each corner of the pocket opening shall have triangle bartacks.

There shall be club pockets located 5 1/4" (plus or minus 1/4") below each hip pocket. The club pockets shall be 1-1/2" (plus or minus 1/4") from the side seam with a minimum opening of 3 1/2" and a minimum depth of 8". Pocketing material to be the same as side and hip pockets. Club pockets shall be constructed using the double welt method on a REECE PW machine and finished in such a manner that there is no topstitching (topstitched club pockets shall be cause for rejection). The corners of the club pockets shall have triangle bartacks for reinforcing strength.

WAISTBAND The trouser will be made with the Freedom Fit® A TWO-ZONE STRETCH waistband system, which is designed to provide the wearer with a more comfortable and better fitting trouser. The waistband shall be constructed using the "closed method" and shall measure 2" wide when finished. The waistband closure shall be accomplished with a crush proof hook and eye. The hook and eye shall be reinforced with stays made of a non-woven fabric that are anchored by the topstitching for the fly facing and curtain. This topstitching must be to the top of the waistband. The waistband must be topstitched 1/16" below the waistband seam for added strength. The top portion of the inside of the waistband is to consist of the same fabric as used for pocketing (70% polyester 30% cotton - minimum 80 X 62 (+/-) 2 count). The fabric is to be cut on the bias for maximum comfort. The waistband is to be 1¾" wide and to finish 1-1/8" wide after construction.

Upper waistband curtain to be inner lined with stretch Ban-Rol or other monofilament stabilizer to prevent roll over. This canvas fabric consists of a warp of 47 ends of texturized nylon and a fill of 34 ends of 750-denier polyester monofilament. The woven fabric is coated with latex, which completely encapsulates all yarns. This finish canvas fabric weighs 12.0 oz/yd2. The canvas will be cut 1-3/8" monofilaments running vertically and have a 10% stretch.

The bottom portion of the waistband curtain will be a blend of 32% nylon, 38% polyester, 18% rubber (3 strands) 11% lycra and 1% acrylic woven 1-7/8" wide and to finish a minimum of 1-5/8"wide. To have a minimum of 40% stretch characteristics.

Note: In a performance stretch waistband, the upper and lower portion of the band will perform different functions.

The upper portion should allow a comfort fit at the waist when bending or sitting, and must maintain a crisp, clean appearance at the outer waistband. This part of the band will stretch 10% and be firm enough to prevent waistband rollover.

FLY Trouser shall have a metal memory lock zipper. There shall be a French Fly tab closure on the inside of the right fly. The tab shall be double ply made of the basic cloth (tabs made of pocketing material or a "grown on" French Fly will be cause for rejection). The right fly shall be lined with the same fabric as the waistband curtain and pocketing. The fly lining shall be sewn to the left fly below the zipper in a neat and durable manner. A button shall be located on the left fly corresponding with the French Fly tab to provide a clean and comfortable closure. There shall be a firm straight bartack at the bottom of the fly going through the zipper tape. The crotch shall be lined in front.

BELT LOOPS There shall be a minimum of seven 3/4" wide interlined belt loops. All loops (except for the back center loop) must be sewn into the bottom of the waistband ("dropped" belt loops are cause for rejection) and the top of the belt loops shall be caught into the waistband curtain seam with a Rocap (or equal) machine. The bottom of the center back loop shall be tacked to the trouser and the top of the loop tacked to the outside of the waistband.

STITCHING, PRESSING & FINISHING Trouser must be stitched with matching thread and all stitching to show must be 10-11 stitches per inch. Trouser must be neatly pressed on Hothead Presses and properly shaped. Outseams and inseams must be pressed open. Trouser must be cleaned and finished to eliminate loose threads.

CREASING The front and rear crease in the trouser legs must incorporate a permanent modified silicone crease produced by the “Lintrak System” or other NATICK approved method.

LABELS Trouser must have a care label permanently affixed that also indicates the size. A paper ticket showing the size, fabric content, cut number, and WPL number must be on the outside of the waistband.

STOCK SIZES Trouser must be available in the following stock sizes:

REGULAR RISE: 28 - 56 (EVEN ONLY OVER 38) HEMMING The trouser leg shall hang to a point not less than 1” nor more than 2” from the top of the heel, in back and hollowed in front to allow the bottoms of the trouser to rest on the shoes without a break. Leg bottoms shall be plain with a minimum 2” turn up. STRIPES Chief & Deputy Chief: A stripe of lustrous black mohair, 1 1/4” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Commanders, Captains & Lieutenants: A stripe of lustrous black mohair, 1” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Sergeants: A stripe of lustrous black mohair, 1/2” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Patrol: A stripe of lustrous black mohair, 1/4” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

6 FEMALE WOOL TROUSERS Flying Cross by Fechheimer Brothers Company SFPDTRSWT

WARRANTY: Garment must have one (1) year warranty against manufacturing workmanship and fabric defects

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC Raeford Mills #13507-only. 19 1/2 to 20 oz/linear yard (60" width) 100% wool elastique two ply warp and filling with a breaking strength of 115 lbs in the warp and 90 lbs in the filling

COLOR DARK NAVY #2135

DESIGN Trouser shall be manufactured from a women's uniform trouser pattern. The trouser styling shall incorporate a plain front and straight leg bottoms. The trouser will have two straight side pockets, two hip pockets, a watch pocket and two club pockets, one below each hip pocket.

POCKETING The pocketing shall be 70% Polyester / 30% Cotton, 2.9 oz. per square yard (60" width) with a minimum 78 X 64 count. Pocketing must have a durable press finish and the color of the pocketing must be black. POCKET DESIGN The two side pockets will have a minimum opening of 6 1/2" and a minimum depth of 5 3/4" measured from the bottom of the pocket opening. Side pockets shall have triangle bartacks at top and bottom of pocket openings Pockets shall be constructed using the stitch, turn, and topstitch method. Pocket facings shall be made of the basic fabric and measure a minimum of 1 1/2" from the bottom of the pocket opening.

There shall be club pockets located 5 1/4" (plus or minus 1/4") below each hip pocket. The club pockets shall be 3/4" (plus or minus 1/4") from the side seam with a minimum opening of 3 1/2" and a minimum depth of 8". Pocketing material to be the same as side and hip pockets. Club pockets shall be constructed using the double welt method on a REECE PW machine and finished in such a manner that there is no topstitching (topstitched club pockets shall be cause for rejection). The corners of the club pockets shall have triangle bartacks for reinforcing strength.

WAISTBAND The trouser will be made with the Freedom Fit® waistband system, a two zone stretch waistband system, which is designed to provide the wearer with a more comfortable and better fitting trouser. The waistband shall be constructed using the "closed method" and shall measure 2" wide when finished. The waistband closure shall be accomplished with a crush proof hook and eye. The hook and eye shall be reinforced with stays made of a non-woven fabric that are anchored by the topstitching for the fly facing and curtain. This topstitching must be to the top of the waistband. The waistband must be topstitched 1/16" below the waistband seam for added strength. The top portion of the inside of the waistband is to consist of the same fabric as used for pocketing (70% polyester 30% cotton - minimum 80 X 62 (+/-) 2 count). The fabric is to be cut on the bias for maximum comfort. The waistband is to be 1¾" wide and to finish 1-1/8" wide after construction.

Note: In a performance stretch waistband, the upper and lower portion of the band will perform different functions.

TRU-GRIP, a ½” surface area composed of thin gauge rubber for max. Comfort and performance and to keep shirts tucked in. Substitution of silicone strip or strips in place of Tru- Grip shall not be acceptable. TRU-GRIP ensures that shirts stay tucked in for neat appearance. FLY Trouser shall have a metal memory lock zipper. The right fly shall be lined with the same fabric as the waistband curtain and pocketing. The fly lining shall be sewn to the left fly below the zipper in a neat and durable manner. There shall be a firm straight bartack at the bottom of the fly going through the zipper tape. The crotch shall be lined in front.

CREASING The front and rear crease in the trouser legs must incorporate a permanent modified silicone crease produced by the “Lintrak System” or other NATICK approved method.

SIZES: 0 2 4 6 8 10 12 14 16 18 20 22 24 26 HEMMING The trouser leg shall hang to a point not less than 1” nor more than 2” from the top of the heel, in back and hollowed in front to allow the bottoms of the trouser to rest on the shoes without a break. Leg bottoms shall be plain with a minimum 2” turn up.

STRIPES Chief & Deputy Chief: A stripe of lustrous black mohair, 1 1/4” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Commanders, Captains & Lieutenants: A stripe of lustrous black mohair, 1” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Sergeants: A stripe of lustrous black mohair, 1/2” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Patrol: A stripe of lustrous black mohair, 1/4” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

7 IKE JACKETWITH PATCHES Flying Cross by Fechheimer Brothers Company SFPD IKE JKT

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC Raeford Mills #13507 Only. 100% Worsted Wool, elastique Weave, 19-1/2 to 20 oz COLOR Dark Navy #2135 BASIC STYLE To be a semi-dress, waist length jacket with a zipper to the bottom of the lapel made with coat sleeves. Jacket is to have both peak lapels and a bi-swing back. A cloth belt is to be stitched down in the back. Epaulets. Side seam straps. Two (2) breast patch pockets with scalloped flaps. Side body. Two (2) inside pockets. Nylon lined, body and sleeve, and inner vitals, including shoulder pads. Badge tab. No waistband. Jacket is to be fitted so it will be worn loosely and straight down over the modified Sam Browne belt and accouterments. The length is to vary in accordance with the individual, but in all cases to fall to the top of the hip pockets. Bottom to be made with a 4-inch bottom turn up with lining sewn to top of turn up and not to include a separate waistband. BODY DETAIL Front will be plain with box pleated patch pockets, flaps, and epaulets. Inside facing of the jacket must be the same as the outer fabric. There shall be a No. 5 YKK brass finish zipper down the front. The back will be seamed (2 piece back) bi-swing back. The ends of each bi-swing will be held in place with a strip of elastic. There shall be a permanent “belt” across the lower back located at the waist. The jacket shall have two side adjustment straps with 24-ligne buttons on each side at the side seam.

LAPELS

To be plain peaked with 15 inch opening and being 3-3/4 inches wide at the widest point. SLEEVE BRAID To have departmental stripe sewn on both sleeves, 3 inches from the bottom of the sleeves, extending halfway around sleeves from seam to seam and set into the seam at both sides.

Chief: to have one gold rayon braid 2 inches wide and positioned 3 inches from the bottom of the sleeves, extending halfway around sleeves from seam to seam and set into the seam at both sides.

Deputy Chief & Assistant Chief: to have two gold rayon braids both measuring ¾ inch wide and positioned 3 inches from the bottom of the sleeves, extending halfway around sleeves from seam to seam and set into the seam at both sides

Commander: to have two gold rayon braids, one measuring ½ inch wide and the other measuring ¾ inch wide, and positioned 3 inches from the bottom of the sleeves, extending halfway around sleeves from seam to seam and set into the seam at both sides

Captains and Lieutenants: to have one gold rayon braid ¾ inch wide and positioned 3 inches from the bottom of the sleeves, extending halfway around sleeves from seam to seam and set into the seam at both sides.

FACING

To be of the same material as the jacket, cut in one piece, not less than 4 inches wide at the top and 3-1/2 inches wide at the bottom. LINING

Fully lined, not quilted, in body and sleeves with 120 count black rayon. COLLAR

Collar shall be properly inner lined and 1-3/4 inches wide at the center with the under collar properly shaped. POCKETS

There shall be two (2) outside box pleated patch pockets measuring 7” deep and 5 ¾” wide. There shall be scalloped flaps set 1” above the pocket openings. Flaps shall measure 6 ¼” wide, 2 ½” at outside points, and 3” at center point. There shall be a non-functional 24-ligne departmental button and corresponding buttonhole in each flap. Flap closure shall be accomplished with hook and loop at each edge of the pocket flap. EPAULETS

Epaulets shall be made of the same fabric as the jacket and shall be sewn into the sleeve seam, cross-stitched, and the end of the epaulet tacked to the jacket at the neck. The epaulet shall be finished with at the point being 2-1/4 inches wide at the sleeve head and 1-1/2 inches wide at the collar and long enough to extend and be tacked down under the collar. There shall be a buttonhole and non-functional button on each epaulet. The button should be placed so it comes flush up the edge of the collar. The epaulet must have two rows of stitching all around and to be stayed across 2 inches above the shoulder seam and cross “X” stitched. BUTTONS There shall be 24-ligne departmental metal buttons on both the epaulets and pocket flaps.

STITCHING Seams to be double stitched and all sewing shall be done with first quality polyester or polyester core thread. ARM SHIELDS

To be piped and made of the same material as the jacket. BADGE TAB

To be tunnel-type badge holder, finished 1 inch wide and 2 inches long, made of two thickness of the jacket material, single stitched all around the edges. To be equipped with two-black rustproof eyelets spaced vertically 7/8 of an inch apart. Top eyelet is to be ¼ inch from top of badge holder. Entire holder is to be attached to the jacket with the center of the top eyelet 2-3/4 inches above the top center of the left pocket flap. CONSTRUCTION

Jacket shall be tailored using “Hymo” type coat fronts, employing standard practice used in coat construction. FINISHING, PRESSING & MISCELLANEOUS

After jacket has been completely sewn and ready for pressing, it shall be pressed on both utility presses, and shaping presses. All loose threads must be removed. All proper size tags, content labels, and care instructions shall be properly affixed to the garment. SHOULDER PATCH

To be attached on both sleeves with the top of the patch 1 inch below the sleeve head seam and in such a manner that a line bisecting the center of the patch would be perpendicular to the ground when the garment is worn. To be sewn on the garment with color fast black thread, not cross-stitched.

DESCRIPTION MANUFACTURER MODEL # IMAGE ITEM #

8 BDU LONG SLEEVE EMBROIDERED SHIRT Flying Cross by Fechheimer 528R5886

SPECIFICATIONS AND ESSENTIAL FEATURES

FABRIC:

Milliken Mills IntelliDry. Style 3455 Color 1688 LAPD Blue with Stain Smart 3 finish. IntelliDry combines fluorochemical-based water repellency on the outside of the garment with proprietary technology for superior moisture wicking on the inside. In addition to repellency and wicking, the fabric releases oily stains in the wash. The dual-sided performance of this smart fabric is achieved through an application that uniquely balances the chemistry to obtain the differential performance. COLOR: Dark Navy STYLE Dress style, fly placket front with zipper, full cut tapered fit, convertible sport collar, long sleeves with square cuffs and dress shirttail. Two pleated breast pockets with topstitched rectangular flaps. Topstitched epaulets. Exterior badge holder with metal eyelets. Back to have topstitched double yoke of shirting material with Hook Velcro attached to the shoulders to correspond to the Loop Velcro on the underside of the epaulets to serve as a microphone holder. Work wear industrial style shirt construction is unacceptable and shall be cause for rejection. The back to have a double yoke. Back length to finish 32 1/2". Side seams to measure 20".

COLLAR: Convertible collar shall be one piece and measure 3" long at points with fused in Mylar stays. Topstitched 1/4" off the edge. Collar to be interlined with #250 Dacron.

FRONT:

To be made with a reverse shirt front having turn back facings of 3". There shall be one button and buttonhole at the lapel and 1 additional button and corresponding buttonhole at the bottom of the shirt, 21” from the top button.In between buttons, there shall be a 15” Talon metal zipper closure. A small piece of Velcro, measuring ½” X 1” shall be sewn above the zipper, for additional closure. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16" raised stitch. Safety stitch joining is unacceptable. EPAULETS:

Asymmetrical shape top-stitched 1/4" off the edge is to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1 3/8" and set not more than 1/2" from folded collar. Cross stitched 2" from sleeve seam. Points of strap are to be stitched down shoulder. Creased and edge stitched shoulder strap construction unacceptable. An additional microphone holder must be included. The Velcro (microphone holder) shall be placed on the under side of the strap to have the loop Velcro measuring 1” X 2” and shall be placed between the cross-stitch and buttonhole. The shoulder (yoke) is to have corresponding hook velcro.

MICROPHONE HOLDER: The underside of the epaulets are to have Loop Velcro 2” wide, 1” deep placed between the cross stitch and the buttonhole. The shoulders (yoke) to have corresponding Hook Velcro to correspond precisely with the Loop Velcro on the epaulets. This will serve as the microphone holder.

BADGE REINFORCEMENT:

Exterior holder to finish 1 1/8" wide X 2-1/4" deep with two black metal eyelets spaced 1 1/4" apart with bottom eyelet centered 1 1/4" above left flap. POCKETS:

Two breast pockets with inverted pleats and square corners. Pocket to measure 6" wide, 6" deep. Left breast pocket to have 1 1/2" pencil stitch. Each pocket to have Velcro tape 3/4" long by 1/2" wide, positioned on both edges of pocket to correspond with outer square flap points as sample. FLAPS:

Rectangular flap design is to measure 6-1/4”" across and 2 1/4" in depth. Secured to the shirt front 1/4" above pocket. Topstitched 1/4" off the edge. Left flap to have invisible pencil opening 1 1/2" to correspond precisely with pencil slot of pocket. Both flaps are to be interlined with Dacron #250. Creased and edge stitched pocket flap construction unacceptable. Under side of the flap to have Velcro tape 3/4" long by 1/2" wide, positioned on outer points of both pocket flaps as sample.

SLEEVES:

Straight at width - no bias - of one piece shaped at head, jacket type. Sleeve vent 5 1/2" long with continuous narrow facings. CUFFS:

To measure 2 1/2" in depth with squared corners as sample. Topstitched 1/4" off the edge. Two button adjustable cuff. Both cuffs to be interlined with #250 Dacron. BUTTONS:

First grade 20-ligne melamine to match. STITCHING:

Single needle throughout. All topstitched 1/4" off the edge. Sleeve inserting and side close felling safety stitched. THREAD:

All sewing threads to be fast color polyester core polyester wrap to match. MILITARY CREASES:

Five (5) stitched-in sharp military creases on all shirts. One crease on each front to be centered vertically not going through the pockets and flaps.

CONSTRUCTION:

Collars, flaps and shoulder straps are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched SIZES:

Shirt shall be made available in the following sizes:

Neck Sizes: S (14&14-1/2), M (15&15-1/2), L (16&16-1/2), XL (17&17-1/2), XXL (18&18-1/2),

XXXL (19&19-1/2), XXXXL (20&20-1/2)

Sleeve Length: Shorts to finish 32”

Regular to finish 34”

Long to finish 36”

X Long to finish 38” EMBROIDERY:

SFPD’s cloth star (silver) with officer’s badge number embroidered in black thread (8 mm block font) sewn above left breast pocket. Officer’s first initial and last name in all CAPS SIZE OF FONT? COLOR OF THREAD? OFCS SILVER/WHITE? LTS GOLD/YELLOW? SPECIALIZED/TACT OLIVE?

SABRE EMBROIDERY FOR MOUNTED(?)

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

9 BDU PANTS –NAVY Fechheimer 49320

SPECIFICATIONS AND ESSENTIAL FEATURES MILL: MILLIKEN FABRIC 65% Polyester / 35% Cotton Twill, 6.5 oz/Square Yard, 2x1 Twill Weave, Warp: 86 Filling: 52, Post Cured Finish, COLOR Dark Blue DESIGN:

Trouser shall be manufactured from a men's uniform trouser pattern. The trouser shall incorporate a plain front, two (2) quarter top front pockets and two (2) hip pockets. Trouser is to be straight leg style. . POCKETING:

The pocketing shall be 70% Polyester / 30% Cotton, 2.9 oz. per square yard (60" width) with a minimum 78 X 64 count. Pocketing must have a durable press finish and the color of the pocketing must be black. POCKET DESIGN

The two (2) front pockets will be quarter top style with a minimum opening of 6" and a minimum depth of 5 3/4" measured from the bottom of the pocket opening. Pockets shall be constructed using the stitch, turn, and topstitch method. Pocket facings shall be made of the basic fabric and shall measure a minimum of 3" in width. The two (2) hip pockets shall have a minimum opening of 5 1/2" and a minimum depth of 5 3/4" measured from the bottom of the pocket opening with rectangular pocket flaps to close with velcro. Hip pockets shall be constructed using the double welt method on a REECE PW Machine and the welts shall be finished in such a manner that there is no top stitching (top stitched hip pockets shall be cause for rejection).

CARGO POCKET:

There shall be two cargo pockets, one on each side seam. There will be double-section pleated patch pockets with rectangular flaps to close with velcro. The pockets will be centered across the side seam and placed 2" below the bottom of the front quarter-top pocket, measuring from the top of the pocket flap. The pocket shall be constructed of the shell fabric and lined with the specified pocketing. The top edge of the pocket shall be bound. The outside measurements of the pocket are 7" wide x 8½" deep with mitered bottom corners. There shall be a 1½" center pleat on each pocket. There shall be a 1½" wide x 1" deep piece of Velcro (male side) sewn to the inner ply of the flap and a corresponding piece of Velcro (female side) sewn on the pleat of the pocket. There shall be a black vislon zipper sewn behind the inner pocket and to the trouser leg so that the zipper is recessed 1" from the top of the pocket flap. There shall be straight vertical bartacks on all four corners of each pocket flap. WAISTBAND:

The trouser will be made with the Freedom Fit®, a two zone stretch waistband system, which is designed to provide the wearer with a more comfortable and better fitting trouser. The waistband shall be constructed using the "closed method" and shall measure 2" wide when finished. The waistband closure shall be accomplished with a crush proof hook and eye. The hook and eye shall be reinforced with stays made of a non-woven fabric that are anchored by the topstitching for the fly facing and curtain. This topstitching must be to the top of the waistband. The waistband must be topstitched 1/16" below the waistband seam for added strength. The top portion of the inside of the waistband is to consist of the same fabric as used for pocketing (70% polyester 30% cotton - minimum 80 X 62 (+/-) 2 count). The fabric is to be cut on the bias for maximum comfort. To be 1¾" wide and to finish 1-1/8" wide after construction.

Upper waistband curtain to be inner lined with stretch Ban-Rol or other monofilament stabilizer canvas. This canvas fabric consists of a warp of 47 ends of texturized nylon and a fill of 34 ends of 750-denier polyester monofilament. The woven fabric is coated with latex, which completely encapsulates all yarns. This finish canvas fabric weighs 12.0 oz/yd2. The canvas will be cut 1-3/8" monofilaments running vertically and have a 10% stretch.

Note: In a performance stretch waistband, the upper and lower portion of the band will perform different functions.

The bottom portion of the waistband stretches over the hip to give support to the lower back and abdomen. In addition, this high stretch portion of the band should constantly be pressed up by the hips, preventing the slack from slipping down while being worn, even if heavy keys, change, or other items are carried in the pockets or on the belt. The single ½” rubberized strand ensure that shirts stay tucked in for neat appearance. FLY: Trouser shall have a metal memory lock zipper. There shall be a buttonhole on the inside right fly. The right fly shall be lined with the same fabric as the waistband curtain and pocketing. The fly lining shall be sewn to the left fly below the zipper in a neat and durable manner. A button shall be located on the left fly corresponding with the buttonhole. There shall be a firm straight bartack at the bottom of the fly going through the zipper tape. BELT LOOPS: There shall be a minimum of seven (7) belt loops 1" in width of double thickness. Each loop must have a non-woven interlining. All loops must be "dropped" with the bottom of the belt loop tacked to the trouser. The top of all belt loops (except for the center back loop) shall be caught into the waistband curtain seam with a Rocap (or equal) Machine. The top of the center back loop shall be tacked to the waistband. CREASES:

The leg creases, front and back will have a silicone bead put in by using the Lintrak process. STITCHING, PRESSING & FINISHING:

Trouser must be stitched with matching thread and all stitching to show must be 10-11 stitches per inch. Trouser must be neatly pressed on Hothead Presses and properly shaped. Outseams and inseams must be pressed open. Trouser must be oven baked after pressing. Trouser must be cleaned and finished to eliminate loose threads. LABELS:

Trouser must have a care label permanently affixed that also indicates the size. A paper ticket showing the size, fabric content, cut number, and WPL number must be on the outside of the waistband. Garment must be made in the United States of America and bear a union label.

STOCK SIZES:

Trouser must be available in the following stock sizes:

REGULAR RISE: 28 - 60 (EVEN ONLY OVER 38)

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

10 SHIRT, LONG SLEEVE, LIGHT BLUE Flying Cross by Fechheimer 45W6625

(MEN’S PSA ONLY)

SPECIFICATIONS AND ESSENTIAL FEATURES MILL Burlington 8130 FABRIC

Content: All synthetic tropical weave 65% Dacron Polyester/35% Rayon conforming to the following specifications:

Weight: 6.6 oz./yd. 2

Construction: 49 warp X 36 filling yarns per sq. inch. All yarns size 10/1 singles

Air Permeability: Ft. 3/Min/Ft. 2 131 ASTM D 737-46

Tensile: Break Strength 105 warp - 90 filling (lbs.)

Properties: Tear Strength 9.7 warp - 8.5 filling (lbs.)

Pilling: Minimum 4.9 rating COLOR: Medium Blue #6625

STYLE: Plain front coat style, form fitting, collar attached, long sleeves with barrel cuffs. Two pleated breast pockets with scalloped flaps. Epaulets. Full badge reinforcement. Matching inside yoke and collar band of high luster Dacron/Cotton Poplin. Flying Cross by Fechheimer Lot 45W6625 or equal value.

COLLAR  Collar points: 3”  Interlining: Woven interlining of #285 Stabilized Mello-Press. Non-woven interlining unacceptable and shall be cause for rejection  Plastic stays: Fused-in Mylar stays, (or equivalent) to be 2 ¾” long 3/8” min. width, and to be fused to underside of collar interlining. Stays applied directly to collar material itself unacceptable  Collar rear: 1 ½”  Collar stand: 1-5/16” and band to be interlined with “Crease-N-Tack” or #250 Dacron Polyester in the band. Collar stand to be lined with poly/cotton to match FRONT  Buttons: First grade 20-ligne melamine, have 7 buttons and buttonholes on the front  Button spacing: 3 ¾” except the spacing between the neck button and the first button on the front which will be 3 ¼” Placket: 1 ½” wide with 2 rows of stitches 7/8” apart, top center placket to have woven interlining of # 550 Stabilized . Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16” raised stitch. Safety stitch joining unacceptable. EPAULETS 2-piece pointed, ¼” topstitched and to be set on yoke with leading topstitch conforming to front joining seam. To measure 2” at sleeve tapering to 1-3/8” and set not more than ½” from collar set seam. Cross-stitched 2” from sleeve seam. Shoulder straps to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable BADGE REINFORCEMENT 2-ply sling 1” wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 buttonhole eyelets 1 ¼” from top of pocket flap spaced 1 ¼” apart and centered on sling POCKETS  Measure: 5-5/8” wide, 6” deep  Breast patch pocket: Two, with mitered corners and 1 ½” stitched pleats  Pleats: Shall be stitched top and bottom and full length of pleat to prevent spreading  Left breast pocket: Have 1 ½” pencil stitch Hook Velcro: Each pocket to have a ¾” long by ½” wide hook Velcro, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement

FLAPS  Construction: 2 piece deep scalloped design to measure 5-7/8” across and 2 ¾” in depth at center point, 2 ¼” at sides. Secured to shirtfront 3/8” above pocket. Flaps to be ¼” topstitched. Flaps to have woven interlining of #550 stabilized Mello-Press. Each flap shall have a button centered on uncut sewn buttonhole  Left flap: To have invisible pencil opening 1 ½” to correspond precisely with pencil slot of pocket  Underside of the flap: To have looped Velcro ¾” long by ½” wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket Creased and edge stitched pocket flap construction unacceptable. Stop & start stitching for pencil opening unacceptable and shall be cause for rejection SLEEVES Sleeve vent shall be a min. of 4 ½” long with one-piece top and bottom facings. Facing to measure 1-1/8” wide point blacked at top CUFFS 2 piece ½” hemmed cuff with ¼” topstitching. Cuffs to measure 3” in depth with rounded corners (barrel cuffs). Cuffs to have 2 buttons and corresponding buttonholes set vertically with one button and buttonhole in center of facing. Cuffs to have woven interlining of #550 Stabilized Mello-Press

BUTTONS:

First grade 19 ligne pearlescent plastic to match. STITCHING:

To have single needle stitching throughout the shirt. All topstitched 1/4" off the edge. Sleeve inserting and side close felling safety stitched. THREAD:

All sewing threads to be fast color polyester core polyester wrap to match. INTERLININGS

Collar interlined with # 285 Stabilized Mello-Press. Cuffs, pocket flaps, shoulder straps and top center to be interlined with # 550 Stabilized Mello-Press. Collar band to be interlined with Crease-N-Tack or #250 Dacron Polyester in the band. MILITARY CREASES: There shall be five Lintrak creases or equivalent silicone sharp military creases on all shirts. One crease on each front to be centered vertically. Front creases shall be through pockets and flaps. Spacing for three military creases across shirt back to be proportionate to the size of the shirt.

STOCK SIZES:

Shirts must be available in the following sizes:

Sleeve lengths: 32-37 inches

Neck sizes: 14-1/2 to 18-1/2, 19, 20, 21, and 22

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

11 SHIRT, SHORT SLEEVE, LIGHT BLUE Flying Cross by Fechheimer 95R6625

(MEN’S PSA AND ACADEMY ONLY)

SPECIFICATIONS AND ESSENTIAL FEATURES MILL

Burlington 8130

FABRIC:

Content: All synthetic tropical weave 65% Dacron Polyester/35% Rayon

conforming to the following specifications:

Weight: 6.6 oz./yd. 2

Construction: 49 warp X 36 filling yarns per sq. inch All yarns size 10/1 singles

Air Permeability: Ft. 3/Min/Ft. 2 131 ASTM D 737-46

Tensile: Break Strength 105 warp - 90 filling (lbs.)

Properties: Tear Strength 9.7 warp - 8.5 filling (lbs.)

Pilling: Minimum 4.9 rating COLOR: Light Blue #6625 STYLE: The style shall be known as a convertible collar, short sleeve, coat Shirt, with full length tail and form-fitting. The Shirt to have two outside breast pockets and scalloped flaps having one button each. Also to have a full badge sling and epaulets. The back to have a double yoke, with high luster Dacron/Cotton Poplin yoke trim. Flying Cross by Fechheimer #95R6625 or equal value. COLLAR 1 piece convertible collar, collar topstitched ¼” off the edge, collar material itself shall have no fusing to Mylar stays (or equivalent) or collar interlining  Collar points: 3”  Plastic stays: Ultrasonically fused-in Mylar stays (or equivalent), have woven interlining of # 285 Stabilized Mello-Press. Stays to be 2 ½” long, 3/8” min., and to be fused to underside of collar interlining. Stays applied directly to collar material itself unacceptable. Collar stand: 1-5/16” and band to be interlined with “Crease-N-Tack” or #250 Dacron Polyester in the band. FRONT  Buttons: Have 7 buttons and buttonholes on the front  Inside yoke to be lined with poly/cotton to match.  Button spacing: 3 ¾” except the spacing between the neck button and the first button on the front, which will be 2 ½”

 Placket: Each front shall have a facing 3” in width, the left front shall have a top center placket 1 ½” wide with 2 rows of stitches 7/8” apart. Stitching on top center is not to be visible on the turn-back facing. Top center placket to have woven interlining #550 Stabilized Mello-Press. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16” raised stitch Non woven interlining is unacceptable and shall be cause of rejection.

EPAULETS To be 2-piece pointed, ¼” topstitched and to be set on yoke with leading topstitch conforming to front joining seam. To measure 2” at sleeve tapering to 1 3/8” and set not more than ½” from collar set seam. Cross-stitched 2” from sleeve seam. Shoulder strap to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable. BADGE REINFORCEMENT 2-ply sling 1” wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 buttonhole eyelets 1 ¼” from top of pocket flap spaced 1 ¼” apart 1 ¼” apart and centered on sling POCKETS  Measure: 5-5/8” wide, 6” deep  Breast patch pocket: Two, with mitered corners and 1 ½” stitched pleats  Pleats: Shall be stitched top and bottom and full length of pleat to prevent spreading  Left breast pocket: Have 1 ½” pencil stitch Hook Velcro: Each pocket to have a ¾” long by ½” wide hook Velcro, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement FLAPS  Construction: 2 piece deep scalloped design to measure 5-7/8” across and 2 ¾” in depth at center point, 2 ¼” at sides. Secured to shirtfront 3/8” above pocket. Flaps to be ¼” topstitched. Flaps to have woven interlining of #550 stabilized Mello-Press. Each flap shall have a button centered on uncut sewn buttonhole  Left flap: To have invisible pencil opening 1 ½” to correspond precisely with pencil slot of pocket  Underside of the flap: To have looped Velcro ¾” long by ½” wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket Creased and edge stitched pocket flap construction unacceptable. Stop & start stitching for pencil opening unacceptable and shall be cause for rejection

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

12 SHIRT, LONG SLEEVE, BLUE (WOMEN’S) Flying Cross by Fechheimer 102W6625 (WOMEN’S PSA ONLY)

SPECIFICATIONS AND ESSENTIAL FEATURES MILL Burlington 8130 FABRIC: Content: All synthetic tropical weave 65% Dacron Polyester/35% Rayon conforming to the following specifications: Weight: 6.0 - 6.6 oz./yd. 2 Construction: 49 warp X 36 filling yarns per sq. inch All yarns size 10/1 singles Air Permeability: Ft. 3/Min/Ft. 2 131 ASTM D 73746 Tensile: Break Strength 105 warp 90 filling (lbs.) Properties: Tear Strength 9.7 warp 8.5 filling (lbs.) Pilling: Minimum 4.9 rating COLOR: Medium Blue #6625 STYLE: Plain front coat style, formfitting, banded collar attached, long sleeves with barrel cuffs. Two pleated breast pockets with scalloped flaps. Epaulets. Full badge reinforcement. Matching inside yoke and collar band of high luster Dacron/Cotton Poplin. Flying Cross by Fechheimer Lot #102W6625.

COLLAR Collar material itself shall have no fusing to Mylar stays (or equivalent)or collar interlining  Collar points: 2-7/8”  Plastic stays: Ultrasonically fused-in Mylar stays (or equivalent). Collar to have woven interlining of # 285 Stabilized Mello-Press. Stays to be 2 ½” long, 3/8” min. width, and to be fused to underside of collar interlining. Stays applied directly to collar material itself unacceptable  Collar rear: 1 ½”, collar topstitched ¼” off the edge Collar stand: 1-5/16” at rear and band to be interlining with “Crease-N-Tack” or #250 Dacron Polyester in the band.

FRONT  Buttons: First grade 20-ligne melamine. The shirt will have 6 buttons and buttonholes on the front  Button spacing: 3 ½” except the spacing between the neck button and the first button on front, which will be 3 ¼” Placket: The right front shall have a top center placket 1 ½” wide with 2 rows of stitches 7/8” apart. Top center placket to have woven interlining of # 550 Stabilized Mello-Press. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16” raised stitch EPAULETS 2-piece pointed, ¼” topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2” at sleeve tapering to 1 3/8” and set not more than ½” from collar set seam. Cross-stitched 2” from sleeve seam. Shoulder straps to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable.

BADGE REINFORCEMENT 2-ply sling 1” wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 buttonhole eyelets 1 ¼” from top of pocket flap spaced 1 ¼” apart and centered on sling POCKETS  Measure: 5” wide, 5” deep  Breast patch pocket: Two, with mitered corners and 1 ¼” stitched pleats  Pleats: Shall be stitched top and bottom and full length of pleat to prevent spreading Hook Velcro: Each pocket to have a ¾” long by ½” wide hook Velcro, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement FLAPS 2-piece deep scalloped design to measure 5 ¼” across and 2 ¼” in depth at center point, 1 ¾” at sides. Secured to shirtfront 3/8” above pocket  Construction: Flaps to be ¼” topstitched. Flaps to have woven interlining of # 550 stabilized Mello-Press.  Each Flap shall have a button centered on uncut sewn buttonhole  Left flap: flap to have invisible pencil opening 1 ¼”. Stop & start stitching for pencil opening unacceptable and shall be cause for rejection  Underside of the flap: To have looped Velcro ¾” long by ½” wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket Creased and edge stitched pocket flap construction unacceptable SLEEVES Sleeve vent shall be a min. of 4 ½” long with one-piece top and bottom facings. Facing to measure 1-1/8” wide point blacked at top

CUFFS 2 piece ½” hemmed cuff with ¼” topstitching. Cuffs to measure 2 ½” in depth with rounded corners (barrel cuffs). Cuffs to be two button adjustable. Cuffs to have woven interlining of # 550 Stabilized Mello-Press BUTTONS: First grade 19 ligne pearlescent plastic to match. NOTE: SPEC. ON FRONTS, INDICATES “MELAMINE” BUTTONS STITCHING: Single needle stitching throughout the shirt. All topstitched 1/4" off the edge. Sleeve inserting and side close felling safety stitched.

THREAD: All sewing threads to be fast color polyester core polyester to match. INTERLININGS

There shall be five Lintrak creases or equivalent silicone sharp military creases on all shirts. One crease on each front to be centered vertically. Front creases shall be through pockets and flaps. Spacing for three military creases across shirt back to be proportionate to the size of the shirt.

CONSTRUCTION

Collars, flaps and cuffs are made with conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out and finally topstitched.

STOCK SIZES:

Shirts must be available in the following sizes:

Bust sizes: 28-52

Sleeve lengths:

28, 30 Regular = 30”

32, 34 Regular = 30” Long = 31”

36, 38 Regular = 31” Long = 32”

40, 42 Regular = 32” Long = 33”

44, 46 Regular = 33” Long = 34”

48 & Up Regular = 34” Long = 35

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

13 SHIRT, SHORT SLEEVE, LIGHT BLUE Flying Cross by Fechheimer 152R6625 (WOMEN’S PSA AND ACADEMY ONLY)

COLOR: Medium Blue #6625 STYLE: The style shall be known as a convertible collar, short sleeve, coat Shirt, with full length tail and form fitting. The Shirt to have two outside breast pockets and scalloped flaps having one button each. Also to have full badge sling and epaulets. The back to have a double yoke, with high luster Dacron/Cotton band and yoke trim. Flying Cross by Fechheimer Lot #152R6625 or equal value. COLLAR 1 piece convertible collar  Collar points: 2-7/8”  Plastic stays: Ultrasonically fused-in Mylar stays (or equivalent). Stays to be 2 ½” long. 3/8” min. width, and to be fused to underside of collar interlining. Stays applied directly to collar material itself unacceptable  Woven interlining: # 285 Stabilized Mello-Press Construction: Collar topstitched ¼” off the edge. Collar material itself shall have no fusing to Mylar stays (or equivalent) or collar interlining FRONT:  Button spacing: 3 ½” except the spacing between the neck button and the first button on the front which will be 2 ½”  Placket: Each front shall have a facing 3” in width. The right front shall have a top center placket 1 ½” wide with 2 rows of stitches 7/8” apart. Stitching on top center is not to be visible on the turn-back facing. Top center placket to have woven interlining of # 550 Stabilized Mello-Press. Non-woven interlining unacceptable and shall be cause for rejection The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between,

EPAULETS 2-piece pointed, ¼” topstitched and to be set on yoke with leading topstitch conforming to front joining seam. To measure 2” at sleeve tapering to 1-3/8” and set not more than ½” from collar set seam. Cross-stitched 2” from sleeve seam. Shoulder strap to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable BADGE REINFORCEMENT: Two-ply sling 1" wide centered over left pocket and stitched to shoulder seam and flap setting stitch. To have 2 buttonhole eyelets 7/8" from top of pocket flap spaced 7/8" apart and centered on sling. POCKETS  Measure: 5” wide, 5” deep  Breast patch pocket: Two, with mitered corners and 1 ¼” stitched pleats  Pleats: Shall be stitched top and bottom and full length of pleat to prevent spreading Hook Velcro: Each pocket to have ¾” long by ½” wide hook Velcro, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement

FLAPS 2-piece deep scalloped design to measure 5 ¼” across and 2 ¼” in depth at center point, 1 ¾” at sides. Secured to shirtfront 3/8” above pocket  Construction: Flaps to be ¼” topstitched, to have woven interlining of #550 Stabilized Mello-Press. Each flap shall have a button centered on uncut sewn buttonhole  Left flap: to have invisible pencil opening 1 ¼”. Stop & start stitching for pencil opening unacceptable and shall be cause for rejection  Underside of the flap: To have looped Velcro ¾” long by ½” wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket Crease and edge stitched pocket flap construction unacceptable SLEEVES To be straight and whole and to have a ¾” hem and to finish at a min. of 8 ½” long from shoulder seam SEWING Collar, shoulder straps and pocket flaps to be topstitched ¼” off the edge. Sleeve inserting and side close felling seams are to be safety stitched

THREAD

All sewing threads to be color fast polyester wrap to match. BUTTONS: First grade 19 ligne pearlescent plastic to match. STITCHING: Single needle stitching throughout the shirt. All topstitched 1/4" off the edge. Sleeve inserting and side close felling safety stitched. INTERLININGS

Collar interlined with #285 Stabilized Mello-Press. Pocket flaps, shoulder straps and top center to be interlined with # 550 Stabilized Mello-Press. MILITARY CREASES: Five silicone military creases on all Shirts. One crease on each front to be centered vertically through pocket and flap. Spacing for military creases on shirt back to be proportionate to the size of the shirt. CONSTRUCTION: Collars, flaps and epaulets are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched. STOCK SIZES:

Shirts must be available in the following sizes:

Bust sizes: 28-52

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

14 Fechheimer 38289 POLYESTER NAVY BLUE TROUSER, MEN’S

(PSA – AIRPORT BUREAU, PSA -- GOLDEN GATE/METRO, ACADEMY)

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC:

100% Texturized polyester serge weave, weight 11.75 oz./linear yard (60- 61" width) fabric shall incorporate a permanent grab tensile 154 lbs warp - 173 lbs fill washable and dry cleanable moisture tongue tear 14 lbs warp - 12 lbs fill transport/soil release release finish. COLOR:

Dark Navy DESIGN:

Trouser shall be manufactured from a men’s uniform trouser pattern. The trouser styling shall incorporate a plain front and straight leg bottoms The trouser will have two straight side pockets, two hip pockets, a watch pocket and two club pockets, one below each hip pocket. POCKETING:

The pocketing shall be 70% Polyester / 30% Cotton, 2.9 oz. per square yard (60" width) with a minimum 78 x 64 count. Pocketing must have a durable press finish and the color of the pocketing must be black. POCKET DESIGN:

The two side pockets will have a minimum opening of 6 ½ " and a minimum depth of 5 3/4" measured from the bottom of the opening. Side pockets shall have triangle bartacks at top and bottom of pocket openings. Pockets shall be constructed using the stitch, turn, and topstitch method. Pocket facings shall be made of the basic fabric and measure a minimum of 1 ½ " from the bottom of the pocket opening.

The two (2) hip pockets shall have a minimum 6" wide opening and a minimum depth of 7 ½ " measured from the bottom of the pocket opening. Hip pockets shall be constructed using the double welt method on a REECE PW Machine and the welts shall be finished in such a manner that there is no topstitching (topstitched hip pockets shall be finished in such

a manner that there is no topstitching (topstitched hip pockets shall be cause for rejection). The corners of the hip pocket openings shall have firm straight bartacks for reinforcing strength.

The watch pocket shall be located on the right front. These pockets shall have a minimum opening of 3 1/4" and depth of 4". The front of the pocket shall be made of pocketing fabric and the back of the pocket shall be made of basic fabric and the two pieces are securely stitched together. Each corner of the pocket opening shall have a firm straight bartack.

There shall be club pockets located 5 1/4" (plus or minus 1/4") below each hip pocket. The club pockets shall be 3/4" (plus or minus 1/4") from the side seam with a minimum opening of 3 ½ " and be constructed using the double welt method on a REECE PW machine and finished in such a manner that there is no topstitching (topstitched club pockets shall be cause for rejection). The corners of the club pockets shall have triangle bartacks for reinforcing strength WAISTBAND:

The waistband shall be constructed using the "closed method" and shall measure 2" wide when finished. The waistband curtain is to be made of the same fabric and color as the pocketing material and shall be attached to the trouser with a zigzag stitch. The waistband must contain BAN-ROL to prevent roll over and have Tru Grip to keep shirts tucked in. The waistband closure shall be accomplished with a crushproof hook and eye. The hook and eye shall be reinforced with stays made of non-woven fabric that are anchored by the topstitching for the fly facing and curtain. This topstitching must be to the top of the waistband. The waistband shall be set on and closed using a lockstitch (use of a chain stitch is unacceptable) to stitch in the band seam through the outer fabric and the waistband curtain. The waistband must be topstitched 1/16" below the waistband seam for added strength. FLY & CROTCH:

Trouser shall have a metal memory lock zipper. There shall be a French Fly tab closure on the inside of the right fly. The tab shall be double ply made of the basic cloth (tabs made of pocketing material or a "grown on" French Fly will be cause for rejection). The right fly shall be lined with the same fabric as the waistband curtain and pocketing. The fly lining shall be sewn to the left fly below the zipper in a neat and durable manner. A button shall be located on the left fly corresponding with the French Fly tab to provide a clean and comfortable closure. There shall be a firm straight bartack at the bottom of the fly going through the zipper tape. The crotch shall be lined in front. BELT LOOPS:

There shall be a minimum of seven belt loops 3/4" in width of double thickness. Each loop must have a non-woven interlining. All loops (except for the back center loop) must be sewn into the bottom of the waistband ("dropped" belt loops are cause for rejection) and the top of the belt loops shall be caught into the waistband curtain seam with a Rocap (or equal) machine. The bottom of the center back loop shall be tacked to the trouser and the top of the loop tacked to the outside of the waistband.

STITCHING, PRESSING & FINISHING:

Trouser must be stitched with matching thread and all stitching to show must be 10-11 stitches per inch. Trouser must be neatly pressed on Hothead Presses and properly shaped. Outseams and inseams must be pressed open. Trouser must be cleaned and finished to eliminate loose threads. LABELS:

REGULAR RISE: 28 - 54 (EVEN ONLY OVER 38)

SHORT RISE: 28 - 40 (EVEN ONLY)

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

15 POLYESTER NAVY BLUE TROUSER, WOMEN’S Fechheimer 35233

(PSA – AIRPORT BUREAU, PSA -- GOLDEN GATE/METRO, ACADEMY)

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC:

100% Dacron polyester 12-12 1/2 Oz./Linear yard (60" Width) elastique weave, tensile strength 240 lbs warp 212 lbs filling fabric incorporate a washable and dry cleanable soil release finish. COLOR:

Navy Blue

DESIGN:

Slack shall be manufactured from a women's uniform trouser pattern with a plain front and one dart on each rear panel above the hip pockets. Slack shall be straight leg design. The slack shall incorporate two-quarter top front pockets and two hip pockets. POCKETING:

The two front pockets will be quarter top style with an opening of 5 1/2" and a depth of 5 1/4" measured from the bottom of the opening. Front pockets to have straight bartacks at the top and bottom of pocket openings. Pockets shall be constructed using the stitch, turn, and topstitch method. Pocket facings shall be made of the basic fabric and shall measure a minimum of 2" in width.

The two hip pockets shall have a 5" wide opening and a 6" depth measured from the bottom of the pocket opening. Hip pockets shall be constructed using the double welt method on a REECE PW Machine. The corners of the hip pocket openings shall have firm straight bartacks for reinforcing strength. The left hip pocket shall have a centered tab made of basic cloth inserted into the top welt with bartacks at the top and bottom of the tab to form an opening for a button. A button shall be located below the bottom welt corresponding in location with the tab. WAISTBAND:

The waistband shall be constructed using the "closed method" and shall measure 2" wide when finished. The waistband curtain is to be made of the same fabric and color as the pocketing material and must be attached to the trouser with a zig-zag stitch. The waistband must contain BAN-ROL to prevent roll over and have Tru Grip OR SNUGTEX in the waistband to keep shirts tucked in. The waistband closure shall be accomplished with a crushproof hook and eye. The hook and eye shall be reinforced with stays made of non- woven fabric that are anchored by the topstitching for the fly facing and curtain. This topstitching must be to the top of the waistband. The waistband shall be set on and closed using a lockstitch (use of a chain stitch is unacceptable) to stitch in the band seam through the outer fabric and the waistband curtain. The waistband must be topstitched 1/16" below the waistband seam for added strength. Waistband is to incorporate elasticized system in rear to ensure comfort and proper fit.

FLY:

BELT LOOPS:

There shall be a minimum of five belt loops, of which are to be Keystone style. Belt loops can be either Keystone or non-Keystone style and measure no less than 7/8” wide each. Keystone loops shall measure 1 3/4" in width at the top and 1 1/4" at the bottom. The center back loop shall be a 3/4" wide straight loop. The Keystone belt loops shall be sewn into the bottom of the waistband and the top of the loops shall be caught into the waistband curtain seam with a Rocap (or equal) machine. The bottom of the center back loop shall be tacked to the trouser and the top of the loop tacked to the outside of the waistband. SEAT:

Seat outlet to measure a minimum of 2 3/4" to allow for alterations. Seat must be sewn with a Tandem Needle Machine. PRESSING AND FINISHING:

Trouser must be neatly pressed on hothead presses and properly shaped. Outseams and inseams must be pressed open. Trouser must be cleaned and finished in such a manner that there are no loose threads. LABELS:

Slacks must have a care label permanently affixed that also indicates the size. A paper ticket showing the size, fabric content, cut number and WPL number must be on the outside of the waistband. Each size ticket must state both the size designation and the actual waist measurement and hip measurement.

SIZES:

6 8 10 12 14 16 18 20 22 24 26

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

16 COMMANDO STYLE PULL-OVER SWEATER, BLACK Flying Cross by Fechheimer Brothers 00701

(PSA – AIRPORT BUREU)

SPECIFICATIONS AND ESSENTIAL FEATURES

FABRIC:

The yarn shall be spun on the worsted system from combed top and shall be of a 2-ply construction. The yarn shall be of 70% Acrylic Monsanto Pil-Trol and 30% Worsted Wool. Color: Black KNIT:

The component parts of body, sleeves, and collar shall be knitted with a 2 x 2 rib knit with 6 Wales and 10-11 Courses per inch. The cuffs and skirt will be a 2x2 rib knit with 8 Wales and 11 Courses per inch. CONSTRUCTION:

The sweater is to have a straight body and set-in sleeves. The body shall be knit in one continuous piece to the required body width. The sleeves and cuffs shall be knit in one continuous piece. The cuffs shall be finished with a non-raveling bottom edge. A matching cotton 5/8” reinforcement tape shall be sewn into the shoulders and underarm. DESIGN:

The sweater is a pullover type with a "V" neck opening, long sleeves with shoulder patches, elbow patches, and shoulder loops with hook and pile fasteners. Nameplate holder and badge patch with eyelets. CLOTH PATCHES AND LOOPS:

The cloth used for making the shoulder patches, epaulets, elbow patches, nameplate and badge tab shall be a matching cloth. BADGE & NAMEPLATE PATCHES:

The badge patch will be 3" x 4" and have metal eyelets spaced 1½" apart. The nameplate will be 1½" x 4" and have metal eyelets spaced 1½" apart. FINISHING & PACKAGING:

Sweaters shall be constructed in a first class manner with patches, thread used throughout. All exposed inside edges must be serged and all loose threads to be thoroughly trimmed. Sweaters to be individually bagged in clear plastic. LABELS:

There shall be permanently affixed content and size labels. CARE:

Washable SIZES:

S (34-36), M (38-40), L (42-44), XL (46-48), XXL (50-52), XXXL (54-56)

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

17 Academy Windbreaker Law Pro made by Quartermaster 14

SPECIFICATIONS AND ESSENTIAL FEATURES JACKET

Metal snap front jacket with self-collar. Polyester taffeta shell with brushed tricot lining. Raglan sleeves. Front slash pockets with welts, Full elastic cuffs. Drawstring at bottom hem. Reinforced hand warmer pockets. Six matching front snaps.

COLOR

Navy, JC 382 SIZE

Small, Medium, Large, X-large, XX-large to 5XL ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

18 DRESS COAT WITH PATCHES Flying Cross by Fechheimer Company Dress Coat #SFPD BLO COAT (Chief, Deputy Chiefs & Commissioned Officers)

FEMALE DRESS COAT:

Female dress coats shall be manufactured to specifically fit the shape and frame of a female.

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC Raeford Mills #13507. 19 1/2 to 20 oz/linear yard (60" width) 100% wool; Elastique two ply warp and filling with a breaking strength of 115 lbs in the warp and 90 lbs in the filing

COLOR Dark Navy #2135 STYLE Four (4) buttons, single breasted, six piece straight front, semi-form fitting, and sack coat. Rolled collar with notch lapels, opening to be 13 to 15 inches to first button. Coat to have an 11 to 12 inch center vent in the back seam. COLLAR Shall not be over 1 7/8" wide in back when finished. Under collar to be made of pre-padded under collar cloth.

LENGTH The coat is to be tailored so that it falls not less than 2 inches and not more than 4 inches at the bottom.

EDGES & SEAMS Double stitched 1/4 inch with plain seams pressed open. The entire coat is to be stitched with thread to be fast color polyester core polyester wrap to match. The center seam in back shall be made so the vent and front to overlap so that they will hang closed at all times. The turn up at the bottom shall not be less than 1-1/4 inches.

OUTLETS All body seams to have outlets of not less than 3/4". Turn up at sleeve cuffs to be not less than 2 1/2".

FACINGS Same material as coat. Cut in one piece not less than 4 inches at the bottom.

BUTTONS Four (4) 36-ligne Gilt San Francisco Police Department buttons sewn on front 4" apart and one (1) 24 Ligne button on each pocket flap.

BUTTONHOLES All buttonholes, excepting epaulet buttonholes, shall be made to a full 1/2" from the edges of the seam and pocket flaps. The ends of the buttonholed shall be bartacked. All buttonholed to be "cut after" machine made buttonholed. All thread used in making buttonholes shall be black buttonhole thread, tailor's button twist, colorfast and guaranteed against fading.

LINING Coat is to be fully lined with black 86 pick nylon taffeta material.

SLEEVE BRAID To have departmental stripe sewn on both sleeves, 3 inches from the bottom of the sleeves, extending halfway around sleeves from seam to seam and set into the seam at both sides.

Chief: to have one gold rayon braid 2 inches wide and positioned 3 inches from the bottom of the sleeves, extending halfway around sleeves from seam to seam and set into the seam at both sides.

EPAULETS To be sewn in sleeve seam directly on tip of the shoulder. The epaulet is to be 2 inches wide and tapering to 1-1/4 inches in width at the side of the neck. The pointed end of the epaulet shall come under the collar and fasten with a 24-ligne metal button at the edge of the collar. The epaulet is to be cross-stitched 1-1/2 inches from the shoulder. The edges are to be double stitched 1/4".

POCKETS Outside Front Pockets:

There shall be two, three pointed flaps measuring 5-1/2” long on each side of the breast. The center of the flap is to be midway between the center of the top button and inside sleeve seam. Flaps are to be 3 inches wide at the ends and center points with the buttonhole and regulation 24-ligne button on the center point of the flap. The top edge of the flap is to be on a line with the center of the top button. Also, the two lower, three pointed flaps, measure 8 inches long and 3-1/2 inches wide at the ends and center points, with a buttonhole and regulation 24-ligne button on the center point of the flap. The top edge of the flap is to be on a line with the hip and center of the bottom button. The inner edge of

both top and bottom flaps are to be on a line and equal distance from the top and bottom buttons. The corners of the flaps are to be sewn down securely to the body of the coat. Flaps are to be graded slightly according to the size of the pocket. All pockets and flaps are to be double stitched 1/4". The inside of the pockets are to be lined with Silesia.

Inside Pockets: Four inside breast pockets are to be piped with same material as the coat. The inside of the pockets are to be lined with Silesia

BADGE TAB A separate badge tab made of same material as the garment, 1" wide with two rustproof black metal eyelets with 3/16 inch inside diameter spaced vertically 7/8 of an inch apart. The length of the badge tab sewn to the jacket shall be 2 1/4" long. The top grommet shall be positioned 6-1/2 inches below the top left shoulder seam of the jacket so that the lower point of the badge is 1" above the breast pocket button.

SWEAT SHIELDS A sweat shield of the same cloth as in the body of the coat, piped with Rayon to be securely set under each arm over the lining

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

19 MALE WHITE DRESS SHIRT LONG SLEEVE Flying Cross by Fechheimer #15W5400

SPECIFICATIONS AND ESSENTIAL FEATURES MILL: Milliken

FABRIC Shall be a Poplin weave, 65% Dacron Polyester/35% Combed Cotton with a finished weight of 4.0 to 4.25 oz. per square yard with a minimum thread count of 104 warp yarns and 54 filling yarns per square inch. Shall have a Permanent Press, Soil Release finish. To be Flying Cross #15W5400.

COLOR White, #81 STYLE Shirt shall be made in coat style, form-fitting, with banded collar, epaulets, badge reinforcement and two pleated outside breast pockets with scalloped flaps. It will have long sleeves with two button barrel cuffs, one button on sleeve facing COLLAR Shall consist of leaf and stand of two-ply with permanently fused-in OR SEWN-IN Mylar stays properly positioned with each collar point. Collar to be styled as sample, with collar points 3 1/4" in length, 1 1/2" in height at back. Collar stand to measure 1 5/16" in height at back and have one button and buttonhole at front. Collar and band to be die cut to insure uniformity. EPAULET The epaulets shall be pointed at the end toward the neck of the shirt. The other end shall be sewn in sleeve head seam. The pointed ends shall be fastened with one button. To measure 2" at sleeve and tapered to 1-3/8". Epaulets to be set about 1/2" from the collar. Epaulets shall be box-stitched to shoulders with row of cross-stitching 2" from sleeve head seam, and diagonally across from each end of seam to the sleeve head seam. Epaulets to be top stitched 1/8" off the edge. Creased and edge stitched shoulder strap construction unacceptable BADGE REINFORCEMENTS Shall have a two-ply sling type badge reinforcement inside left front of shirt, 1" wide to be centered and secured in left shoulder seam and left flap setting seam. Two buttonhole eyelets are to be spaced 1 1/4" apart with the bottom eyelet 1 1/4" from the top of the left pocket flap.

FRONTS Left: To have 1 5/8" turned back selvage edge facing along front edge. Facing to be held in position only by 6 well-sewn buttonholes.

Right: To have 1" hemmed self-button piece along front edge with 6 buttons to correspond with left front buttonholes.

The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16" raised stitch. Safety stitch joining is unacceptable.

POCKETS The shirt shall have two outside 1 1/4" pleated breast pockets with scalloped flaps. Flap to finish 2 3/4" at center point and 2 1/4" at sides. Flaps to be secured to front of shirt 1/4" above pocket. Left flap is to have invisible pencil opening 1 1/2" wide. Pocket shall be clip corner design to finish 5 5/8" wide and 6" deep. The left breast pocket is to have a pencil stitch 1 1/2" wide. Creased and edge stitched pocket flap construction unacceptable. Button centered on pocket to align with buttonhole in flap.

SLEEVES & CUFFS To be long sleeve cut straight and whole with pleats and 5 1/2" sleeve vent. Sleeve vent shall have a top facing 1 1/8" wide finished at the top with a neatly. Cuff to measure 2 1/2" with rounded corners. There shall be two ADJUSTABLE buttons with corresponding buttonholes on each cuff and one button and buttonhole in the sleeve facing.

BUTTONS Shall be first grade, pearlescent plastic, 19 ligne to match.

SEWING Collar and pocket flaps shall be stitched 1/8 inch from edge. Side closing and sleeve setting shall be made with safety-stitch type machine. Shoulder straps and cuffs to be topstitched 1/8” off edge. All stitching will be with no fewer than 12 to 14 stitches per inch. Bottom hem shall be a continuous hem 3/8" without any gussets.

THREAD All sewing threads to be fast color polyester core polyester wrap to match.

INTERLINING Collars, pocket flaps and cuffs to be interlined with 100% Dacron #250.

SIZE MARKING Size tag sewn into collar seam.

CONSTRUCTION

Collars, flaps and epaulets are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

20 FEMALE WHITE DRESS LONG SLEEVE SHIRT Flying Cross by Fechheimer #139R5400

SPECIFICATIONS AND ESSENTIAL FEATURES MILL: Milliken

FABRIC Shall be a Poplin weave 65% Dacron Polyester/35% Combed Cotton with a finished weight of 4.0 to 4.25 oz. per square yard with a minimum thread count of 104 warp yarns and 54 filling yarns per square inch. Shall have a Permanent Press, Soil Release finish.

COLOR White #81.

STYLE Plain front coat style, form fitting, collar attached, long sleeves with barrel cuffs. Two pleated breast pockets with scalloped flaps. Shoulder straps. Badge tab. Matching inside yoke and collar band. Darts on front at shoulder and at waist and two vertical back darts.

COLLAR Convertible collar shall be one piece and to measure 2-7/8" long at points. The collar shall be made with fused in Mylar stays. Collar to be topstitched 1/8" off the edge. Collar to be interlined with #250 Dacron.

EPAULETS The epaulets shall be pointed at the end toward the neck of the shirt. The other end shall be sewn in sleeve head seam. The pointed ends shall be fastened with one button. To measure 2" at sleeve tapering to 1 3/8" and set not more than 1/2" from folded collar. Cross stitched 2" from sleeve seam. Creased and edge stitched shoulder strap construction unacceptable.

BADGE REINFORCEMENTS Two-ply sling 1" wide centered over left pocket and stitched to shoulder seam and flap setting stitch. Inside reinforcement piece to be held in place by horizontal eyelets. Two have 2 buttonhole eyelets 7/8" from top of pocket flap spaced 1-1/4”" apart and centered on sling. Bottom eyelet to be 1-1/4” above left flap.

FRONTS Each front shall have a facing 3" in width extending from neckline to bottom of shirt provided by a turn under of material. The right front shall have 6 buttonholes spaced 3 1/2" apart and to be set 3/4" from edge. Second buttonhole to be positioned 2 1/2" from top button, balance of buttons spaced 3 1/2" apart. Buttons to be strongly attached through two thickness of material forming left front, and shall correspond to each buttonhole. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16" raised stitch. Safety stitch joining unacceptable.

POCKETS Two breast pockets with 1 1/4" stitched pleats. Pockets to measure 5" wide, 5" deep. Left breast pocket to have 1 1/4" pencil stitch.

FLAPS: Deep scalloped design to measure 5 1/4" across and 2 1/4"in depth at center point, 1 3/4" at sides. Secured to shirtfront 1/4" above pocket. Left flap to have invisible pencil opening 1 1/4". Both flaps to be inter-lined with #250 Dacron. Creased and edge stitched pocket flap construction unacceptable.

SLEEVES:

Straight at width no bias of one piece shaped at head, jacket type. Sleeve vent 4 3/4" long with top and bottom facings. Top facing to measure 1 1/8" wide point blocked at top. Underfacing 1-1/8" wide.

CUFFS:

To measure 2 1/2" in depth with rounded corners. With two button adjustable cuff. Both cuffs to be inter-lined with #250 Dacron.

BUTTONS Shall be first grade 19-ligne pearlescent plastic to match.

STICHING Single needle stitching throughout the shirt. All topstitched 1/8" off the edge. Sleeve inserting and side close felling, safety stitched.

THREAD All sewing threads to be fast color polyester core polyester wrap to match

CONSTRUCTION Collars, flaps and shoulder straps are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

21 LONG SLEEVE POLO SHIRTS VF Imagewear/Horace Small HS5127 (Dark Navy) HS5128 (Black)

SPECIFICATIONS AND ESSENTIAL FEATURES POLO SHIRT:

Dri-Balance Technology gives superior breathability and absorption, keeping wearer dry in all activities. Plated knit with jersey face and mesh back provides superior color retention. Double layer sweat patch on the center back of the neck. Raglan sleeves combined with straight side panels for an athletic, technical look with superior freedom of movement. Dyed to match rib knit, no curl collar with collar stays. Interlined three button front placket. Double needle cuff and bottom hem. Heat seal transfer neck label eliminates tag irritation. Reinforces mic loop at base of placket and two concealed mic pockets at dropped shoulder seams. SIZE:

XSmall, Small, Medium, Large X-large, XX-large to 4XL WEIGHT:

Special OPS POLO

63% cotton/37% polyester COLOR:

Dark Navy, Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

22 SHORT SLEEVE POLO SHIRTS VF Imagewear/Horace Small HS5123 (Dark Navy) HS5124 (Black)

SPECIFICATIONS AND ESSENTIAL FEATURES

POLO SHIRT:

XSmall, Small, Medium, Large X-large, XX-large to 4XL WEIGHT:

Special OPS POLO

63% cotton/37% polyester COLOR:

Dark Navy, Black, Red

23 BICYCLE PURSUIT PANTS Mocean 2020 S

SPECIFICATIONS AND ESSENTIAL FEATURES

BICYCLE PANTS

Supplex, nylon pants coated with Teflon ht., water repellant barrier and fabric protector. Zipper fly, gusseted crotch, tapered legs. Articulated knees with vents, two zippered pockets, two zippered back pockets, a pen pocket, shirred waistband with five belt loops and zipper cuff opening.

COLOR

Shell fabric: Navy

LINING

Black

ZIPPER & POCKETING

Black

SIZES

Extra Small, Small, Medium, Large, X Large, 1X Large, 2 X Large, 3X Large

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

24 BICYCLE SHIRT Flying Cross by Fechheimer 85R5456

SPECIFICATIONS AND ESSENTIAL FEATURES

FABRIC

Content: Poplin weave, 65% Dacron Polyester/35% Combed Cotton

Weight: 4.0 to 4.25 oz. per square yard

Construction: 104 warp yarns and 54 filling yarns per square inch

COLOR

LAPD Navy

STYLE

The style shall be known as a convertible collar, short sleeve coat shirt with full-length tail and form fitting. The shirt is to have two outside pleated breast pockets with scalloped flaps, epaulets and a full badge sling. The back is to have a double yoke. Shirt should have a 4 ½” mesh underarm panel.

COLLAR

Convertible collar shall be one piece and to measure 3" long at points. The collar shall be made with fused-in Mylar stays. Collar to be topstitched 1/8” off the edge and to be interlined with #250 Dacron.

FRONT

Each front shall have a facing 3" in width. The left front shall have a top center 1-1/2" wide with two rows of stitches 7/8 inches apart. Stitching on top center is not to be visible on the turn-back facing. The shirt will have 7 buttons and buttonholes on the front, spacing between each will be 3-3/4" except the spacing between the neck button and the first button on the front, which will be

3-1/4". Top center interlined with #250 Dacron. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16" raised stitch. Safety stitch joining is unacceptable.

EPAULETS:

Asymmetrical shape double needle topstitched 1/8” to be set on yoke with leading topstitch conforming to joining seam. To measure 2" at sleeve tapering to 1 1/2" and set not more than 1/2" from folded collar. Cross stitched 2" from sleeve seam. Creased and edge stitched epaulet construction unacceptable.

BADGE REINFORCEMENT:

Two-ply sling is 1" wide centered over the left pocket and stitched to shoulder seam and flap setting stitch. To have 2 buttonhole eyelets 1-1/4 inches from top of pocket flap spaced 1-1/4 inches apart and centered on the sling.

SLEEVES

Sleeves are to be straight and whole, to have 3/4" hem and to finish 9 3/4" from shoulder seam.

POCKETS:

Two breast pockets with 1-1/4 inches stitched pleats. Pocket to measure 5-5/8" wide, 6" deep. Left breast pocket to have l-1/2" pencil stitch. Each pocket to have Velcro fasteners 3/4" long by l/2" wide, positioned on both edges of pocket to correspond with outer scalloped flap points.

FLAPS:

To have deep scalloped flaps design to measure 5-7/8" across and 2-3/4" in depth at center point, 2-l/4" at sides. The flap is secured to the shirt front 1/4” above the pocket. The left flap is to have invisible pencil opening l-l/2" to correspond precisely with pencil slot of pocket. Flaps to be topstitched 1/8” off the edge and interlined with Durapress #250 Dacron. Creased and edge stitched pocket flap construction unacceptable. The underside of the flap is to have Velcro fasteners 3/4" long by 1/2" wide positioned on outer points of both pocket flaps.

Button to be sewn on the top of the flap.

BUTTONS:

First grade 19-ligne pearlescent plastic to match.

STITCHING:

Single needle stitching is to be done throughout the shirt. All topstitched 1/8 inch off the edge. Sleeve inserting and side close felling, safety stitched.

THREAD:

All sewing threads to be fast color polyester core polyester wrap to match

INTERLINING:

Collars, pocket flaps, epaulets and top center to be interlined with 100% Dacron #250.

MILITARY CREASES:

Five stitched-in sharp military creases on all shirts. Spacing for military creases on shirt back to be proportionate to the size.

CONSTRUCTION:

Collars, flaps and epaulets are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched.

MESH INSERT:

A black mesh insert shall be added to this shirt under the arms about 2” below the set in sleeve. The mesh shall be 4” wide and extend to the bottom of the shirt.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

25 BICYCLE SHORTS Mocean 1059 Cargo Shorts

SPECIFICATIONS AND ESSENTIAL FEATURES

CARGO SHORTS –

• Supplex® nylon w/Teflon HT® shell • Loose fit with 7 1/2-inch inseam • 'Varied Fit Waist™' half fitted/ half elastic waist with a zipper fly, snap closure and 'Floating Beltloops™' • Full-length pleat from waist to hem • Gusseted crotch for ease of MOCEAN • 2-side seam 'Reservoir Pockets™' • 2-cargo pockets with gusset and Velcro'd® flap • 2-back pockets with zipper closures and flaps • 1-pen pocket with two pen ports • Loose, nonbinding hem • Double needle top stitching w/ bartacks on all stress points MOCEAN's FLEX VENT MESH™ SOLUTION - Flex-Vent-Mesh: Incredibility stretchy, Flex-Vent-Mesh has excellent 4-way stretch properties and its liher content lends itself well to wicking perspiration and drying quickly. What is Flex-Vent-Mesh? It is a high quality, warp knit fabric that has unusual strength and durability for its weight and construction. Its robust quality and slippery hand is excellent for placement in high friction areas, such as over knees and under arms. Why not regular mesh? Either too light, too heavy or not slippery enough. Flex-Vent- Mesh is perfect due to its unique balance of stretch and durability for everyday use around friction areas in high quality, professional uniforms. Does Flex-Vent-Mesh have good memory? We should call it Elephant Mesh. Flex-Vent-Mesh will stretch and recover for the life of the garment.

COLOR: BLACK or POLICE NAVY

SIZE TAG:

The shorts shall have a sewn in label giving care instructions, sizes, and fiber content

SIZE RANGE:

XS – 5XL

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

26 BICYCLE JACKET (ONE PIECE CYCLING JACKET) Mocean 6023S SFPD

SPECIFICATIONS AND ESSENTIAL FEATURES

BICYCLE JACKET

Shell 100% nylon supplex Face Ultrex. Lining is Cool max Upper, 160 X 90 nylon lower. ½” 3M reflective tape on front and back cape, and along 1-1/2 elastic shirred waistband. 3M reflective piping at front an back of both sleeves. Two Velcro belt keepers at back waistband, two dual entry pockets on outer shell, 8” zipper at top, under front cape and fleece lined, side entered hand warmer pockets underneath. Two epaulets, 5” long, snap closure. Gusseted Velcro closing cuffs. Three pen pocket left front. Inside lining has two top entered welted pockets and has an elastic stormbelt. Jacket is two way zippered closed with two snaps at collar, one snap lower front waistband. Collar is full 4” wide, for zipping up and snapping for harsh weather conditions. Knit storm collar on the inside shell collar. Lettering is heat pressure applied in black reflective letters to the front and back of garment. Velcro name tag strip on right front, above “POLICE” lettering. Badge tab is 2-1/2” X 1” with two eyelets at 2-1/4” apart.

COLOR

Navy Blue

SIZES:

X-Small, Medium, Large, X Large, 1X Large, 2X Large, 3X Large,

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

27 BREECHES WITH GOLD STRIPES (MOUNTED) Flying Cross by Fechheimer SFPD MOU BRE

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC Raeford Mills #13507 only. 19 1/2 to 20 oz/linear yard (60” width) 100% wool elastique two ply warp and filling with a breaking strength of 115 lbs in the warp and 90 lbs in the filling.

COLOR DARK NAVY #2135 DESIGN Breeches shall be manufactured from up-to-date patterns and shall be designed so that there will be a high "peg" at the hip, and no baggy seat. The front shall be plain (no pleats) with two (2) top pockets, two (2) hip pockets with flaps to button, one (1) club pocket below right hip pocket and one (1) watch pocket on the right side. All pockets shall be bartacked with triangle bartacks except for the top pocket and watch pocket, which is to have straight bartacks. Hip pockets will be of the double welt method, manufactured on Reece PW Machine, and shall be finished in such a manner that there is no top stitching. The welts shall be interlined with Pellon. POCKET DESIGN The two front ½ top pockets will have a minimum opening of 6 1/2" and a minimum depth of 5 3/4" measured from the bottom of the pocket opening. Side pockets shall have straight bartacks at top and bottom of pocket openings. Pockets shall be constructed using the stitch, turn, and topstitch method. Pocket facings shall be made of the basic fabric and measure a minimum of 1 1/2" from the bottom of the pocket opening.

The two hip pockets shall have a minimum opening of 5-1/2”" and a minimum depth of 6-1/8”" measured from the bottom of the pocket opening. Hip pockets shall be constructed using the double welt method on a REECE PW machine and the welts shall be finished in such a manner that there is no topstitching (topstitched hip pocket welts shall be cause for rejection). The corners of the hip pockets shall have triangle bartacks for reinforcing strength. Rear pocket flaps shall be added to garment with both flaps to be closed with buttons going through pocket flap.

There shall be club pockets located 3" below each hip pocket. The club pockets shall be 2-1/4" from the side seam with a minimum opening of 3 1/2" and a minimum depth of 9". Pocketing material to be the same as side and hip pockets. Club pockets shall be constructed using the double welt method on a REECE PW machine and finished in such a manner that there is no topstitching (topstitched club pockets shall be cause for rejection). The corners of the club pockets shall have triangle bartacks for reinforcing strength.

POCKETING The pocketing shall be 70% Polyester / 30% Cotton, 2.9 oz. per square yard (60" width) with a minimum 78 x 64 count. Pocketing must have a durable press finish and the color of the pocketing must be a natural drill.

FLY LINING The right fly shall be the same fabric and color as the waistband and pocketing. The right fly lining must be sewn to the left fly below the zipper with strong closure and smart appearance. There shall be a French Fly closure on the inside of the right fly, and the fabric for the French Fly must be the same as the outer material of the trousers.

BELT LOOPS There shall be 7 belt loops, 2" wide, of double thickness, and each loop must be interlined with a non-woven fabric. All loops (except for the back center loop) must be sewn into the bottom of the waistband, and the top of all loops shall be caught into the waistband curtain seam. The waistband shall measure 2" wide when finished, wide enough to comfortably accommodate a belt 1 5/8" wide. The back center loop shall be 1" wide.

MISCELLANEOUS:

Breeches must have a YKK #42 Memory Lock zipper, the tape of which has permanent press finish, and there shall be a bartack at the bottom of the fly, going through the zipper tape. The breeches must be seamed with matching thread and the seat seam must be stitched with a Tandem needle machine (2 threads). All exposed inside edges must be serged. Breeches to have back reinforcement and front knee strapping. Bottoms of breeches shall have zipper closures.

STRIPE Captains & Lieutenants: A stripe of lustrous gold mohair, 1” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Sergeants: A stripe of lustrous gold mohair, 1/2” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Patrol: A stripe of lustrous gold mohair, 1/4” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

LABELS:

Breeches must have a care label permanently affixed that also indicates the size. A paper ticket showing the size, fabric content, cut number, and WPL number must be on the outside of the waistband.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

28 BREECHES WITH MOHAIR BRAID (MOTORCYCLES) Flying Cross by Fechheimer SFPD MOT BRE

COLOR DARK NAVY #2135 DESIGN Breeches shall be manufactured from up-to-date patterns and shall be designed so that there will be a no "peg" at the hip, and no baggy seat. The front shall be plain (no pleats) with two (2) top pockets, two (2) hip pockets with flaps to button, one (1) club pocket below each hip pocket and one (1) watch pocket on the right side. All pockets shall be bartacked with diamond bartacks except for the watch pocket, which is to have straight bartacks. Hip pockets will be of the double welt method, manufactured on Reece PW Machine, and shall be finished in such a manner that there is no top stitching. The welts shall be interlined with Pellon.

POCKET DESIGN The two front ½ top pockets will have a minimum opening of 6 1/2" and a minimum depth of 5 3/4" measured from the bottom of the pocket opening. Side pockets shall have straight bartacks at top and bottom of pocket openings. Pockets shall be constructed using the stitch, turn, and topstitch method. Pocket facings shall be made of the basic fabric and measure a minimum of 1 1/2" from the bottom of the pocket opening.

be cause for rejection). The corners of the hip pockets shall have triangle bartacks for reinforcing strength. Rear pocket flaps shall be added to garment with both flaps to be closed with buttons going through pocket flap.

There shall be club pockets located 3" below each hip pocket. The club pockets shall be 1-1/4" from the side seam with a minimum opening of 3 1/2" and a minimum depth of 9". Pocketing material to be the same as side and hip pockets. Club pockets shall be constructed using the double welt method on a REECE PW machine and finished in such a manner that there is no topstitching (topstitched club pockets shall be cause for rejection). The corners of the club pockets shall have triangle bartacks for reinforcing strength. POCKETING The pocketing shall be 70% Polyester / 30% Cotton, 2.9 oz. per square yard (60" width) with a minimum 78 x 64 count. Pocketing must have a durable press finish and the color of the pocketing must be a natural drill.

WAISTBAND Waistband curtain to be of the same fabric as the pocketing and shall close with a hook and eye. The waistband curtain must be attached to the trouser with a zigzag stitch. There must also be a Tru Grip in the waistband, a ½” surface area composed of thin gauge rubber for max. Comfort and performance and to keep shirts tucked in. Substitution of silicone strip or strips in place of Tru-Grip shall not be acceptable. . FLY LINING The right fly shall be the same fabric and color as the waistband and pocketing. The right fly lining must be sewn to the left fly below the zipper with strong closure and smart appearance. There shall be a French Fly closure on the inside of the right fly, and the fabric for the French Fly must be the same as the outer material of the trousers.

BELT LOOPS There shall be 7 belt loops, 2" wide, of double thickness, and each loop must be interlined with a non-woven fabric. All loops (except for the back center loop) must be sewn into the bottom of the waistband, and the top of all loops shall be caught into the waistband curtain seam. The waistband shall measure 2" wide when finished, wide enough to comfortably accommodate a sa 1 5/8" wide. The back center loop shall be 1" wide.

MISCELLANEOUS

Breeches must have a YKK #42 Memory Lock zipper, the tape of which has permanent press finish, and there shall be a bartack at the bottom of the fly, going through the zipper tape. The breeches must be seamed with matching thread and the seat seam must be stitched with a Tandem needle machine (2 threads). All exposed inside edges must be serged. Breeches to have a full back reinforcement and front knee strapping. Bottoms of breeches shall have zipper closures.

STRIPES Chief & Deputy Chief: A stripe of lustrous black mohair, 1 1/4” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Commanders, Captains & Lieutenants: A stripe of lustrous black mohair, 1” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Sergeants: A stripe of lustrous black mohair, 1/2” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser.

Patrol: A stripe of lustrous black mohair, 1/4” wide, on outside seams which shall extend from the bottom of the side pocket to the bottom of the trouser. LABELS

Breeches must have a care label permanently affixed that also indicates the size. A paper ticket showing the size, fabric content, cut number, and WPL number must be on the outside of the waistband.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

29 SHORT SLEEVE POLO SHIRTS- EVOC and RANGE VF Imagewear/Horace Small HS5134 (Red)

SPECIFICATIONS AND ESSENTIAL FEATURES POLO SHIRT:

XSmall, Small, Medium, Large X-large, XX-large to 4XL WEIGHT:

Special OPS POLO

63% cotton/37% polyester COLOR:

Red

EVOC star embroidered on left chest- standard

1 Line monogramming on right chest- standard, All caps block letters, ½” size letters in Mediera thread #1011 with First initial & last name

IMAGE

SHORT SLEEVE POLO SHIRTS- Range

SPECIFICATIONS AND ESSENTIAL FEATURES

POLO SHIRT:

XSmall, Small, Medium, Large X-large, XX-large to 4XL WEIGHT:

Special OPS POLO

63% cotton/37% polyester COLOR:

Red

Range Instructor shirts should have “FIREARMS INSTRUCTOR” embroidered on the right breast. On the left breast “SAN FRANCISCO POLICE” with the eagle emblem and “RANGE STAFF” underneath should be embroidered.

Rangemaster shirts should have “SAN FRANCISCO POLICE” with the eagle emblem and “RANGEMASTER” embroidered underneath.

ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE

3-in-1 PARKA SAFETY-JACKET FOR RANGE, 5.11 TACTICAL E.V.O.C, CSI 30 48001 Red

48001-019 Black

COLOR: Black, Red Contractor shall include the following at no additional cost to the city:

 Police cloth star (silver or gold) with officer’s badge number embroidered in black thread (8 mm block font) sewn onto left chest pull out flap

 Officer’s last name only embroidered onto right chest pull out flap in 12 mm Block font, utilizing Madeira # 1024, Silver or gold color thread o “RANGE STAFF” shall be embroidered ½” below officer’s last name for Range Staff o “EVOC STAFF” shall be embroidered ½” below officer’s last name for EVOC Staff o “C.S.I.” shall be embroidered ½” below officer’s last name for CSI Staff

 “E.V.O.C.” shall be Silk Screened onto back pull out flap for EVOC Staff  “RANGE STAFF” shall be Silk Screened onto back pull out flap for Range Staff  “CSI” shall be Silk Screened onto back pull out flap for CSI personnel

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

31 TACTICAL BDU LONG SLEEVE EMBROIDERED 5.11 TACTICAL INC. 72002-724 (NAVY) SHIRT

Men’s BDU Shirt Poly/Cotton Ripstop, 5.7 oz

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC 65% polyester / 35% cotton stop COLOR Dark Navy, Black DESIGN:

The shirt is made with 65% polyester and 35% cotton rip stop for a professional appearance and comfort. The short sleeve shirt shall incorporate patented document pockets on the front chest. The shirt has a hidden placket with melamine buttons. Bi-swing shoulder design allows for extra movement through the back shoulder area. The shirt bottom is a straight cut. The shirt is Teflon treated. The shirt comes with triple stitching and 28 bartacks for added strength. POCKET DESIGN:

The two front chest pockets are flat with Velcro closure. The two (2) hidden document pockets can hold large documents or necessary equipment. The pockets end at the arm/side seam in width and underneath the front chest pocket in length. They open ½” from the edge of the placket and have two hook and loop strips to close the pocket opening.

LABELS:

Shirt must have a care label, size label, country of origin and fiber content label permanently attached to the garment. BUTTONS/ZIPPERS:

Buttons – Melamine buttons that won’t melt, burn or crack. STOCK SIZES:

Shirts must be available in the following stock sizes:

Men’s: Small/Medium/Large/Extra Large/2XL/3XL/4XL

SHIRT COLORS Dark Navy Blue EMBROIDERY: Remove any creases prior to embroidery

Officer’s first initial and last name on right chest ½” above pocket in 1-line monogramming (Madiera Silver #1011 for Officers/Sergeants, Madiera Gold #1024 for Lieutenants/Captains);

Crossed rifles on right chest 1/2” above name -.50” 1-line monogramming in Madiera Silver #1011 for Officers/Sergeants, in Madiera Gold #1024 for Lieutenants/Captains;

Officer’s star with number on left chest; badge # in .25” block new font style in black madeira thread #1000 inside the star, ½” above the pocket

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

32 MEN’S BDU SHIRT POLY/COTTON RIP STOP, 5.11 TACTICAL INC. 72002-019 (BLACK)

5.7 oz. Add subdued name strips attached over the right pocket, subdued cross rifles over the name strip and

subdued star attached over left pocket

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC: 65% polyester / 35% cotton stop

DESIGN:

POCKET DESIGN:

Shirt must have a care label, size label, country of origin and fiber content label permanently attached to the garment. BUTTONS/ZIPPERS:

Buttons – Melamine buttons that won’t melt, burn or crack. STOCK SIZES:

Men’s: Small/Medium/Large/Extra Large/2XL/3XL/4XL SHIRT COLORS Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

33 TACTICAL BDU PANTS (Tact Only) 5.11 TACTICAL INC. 74003-724 (NAVY)

SPECIFICATIONS AND ESSENTIAL FEATURES

FABRIC 65% Polyester / 35% Cotton Ripstop DESIGN

The pant shall incorporate a plain front, two (2) quarter top front pockets, (2) back utility pockets with hook and loop closure, and two (2) BBStm cargo pockets. The pants must be double seated. The waist band shall be an expandable comfort waist with reinforced waist band. The pants have a double knee with removable neoprene knee pads. The pants are triple stitched and there are 45 bar tacks for added strength. The pants are Teflon treated. POCKET DESIGN:

The two (2) front pockets will be quarter top style with a minimum opening of 7 ½” and a minimum depth of 5 ½” measured from the bottom of the pocket opening. Pockets shall be constructed using the stitch, turn, and topstitch method, also known as a French seam. The edges of the front pockets shall be reinforced with binding of fabric at each bottom edge.

The two (2) rear hip pockets shall have a minimum opening of 5 ½” and a minimum depth of 6 ½” measured from the bottom of the pocket opening. Hip pockets shall have 2” pocket flaps with Velcro closures at each corner.

The two (2) cargo pockets, (one on each side seam) shall have two inner pocket compartments. The pockets will be centered across the side seam. The outer pocket shall be constructed of the shell fabric. The inner compartments are formed with a layer of loop material. The loop material serves as a mounting surface for 5.11’s hook based material on the Accessories Pouches. The outside measurements of the pocket are 9” wide x 10” deep. There shall be two (2) working 1” pleats on each pocket. There shall be a 1 ½” bellow on the back vertical edge of the pocket. The pocket flaps shall be secured with 1 ½ x ¾ inch hook and loop tabs at each corner. There shall be “X” bar tacks on all corners of each pocket flap. WAISTBAND:

The pant will be made with the 5.11 Comfort Tunnel Waistband, which provides 2 inches of expansion at each side for better comfort and fit. The waistband shall measure 2” wide when finished. The waistband shall be closed with a PRYM snap and a French fly. The waistband must be topstitched 1/8” along both edges for added strength.

BELT LOOPS:

Side and front belt loops shall be 1 ¾” wide and have a functional opening of 2 ¼”. The center back loop shall be 1” wide. There must be a minimum of five (5) belt loops at the waist.

STITCHING, PRESSING & FINISHING:

Trouser must be stitched with matching thread. Trouser must be cleaned and finished to eliminate loose threads. LABEL:

Trouser must have a care label, size label, and country of origin and fiber content label permanently attached to the garment BUTTONS/ZIPPERS/SNAPS:

YKK Zipper - #5 metal tooth zipper

PRYM Snap - #26L Antique Brass Anodized Black Metal Snap STOCK SIZES:

Trouser must be available in the following stock sizes:

XS – 4XL in short, regular and long COLORS:

Trouser must be available in the following colors:

Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

34 TACTICAL BDU PANTS (Tact Only) 5.11 TACTICAL INC. 74003-019 (BLACK)

Need name strip over right rear pant pocket

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC 65% Polyester / 35% Cotton Ripstop

DESIGN

BELT LOOPS:

Side and front belt loops shall be 1 ¾” wide and have a functional opening of 2 ¼”. The center back loop shall be 1” wide. There must be a minimum of five (5) belt loops at the waist. STITCHING, PRESSING & FINISHING:

Trouser must be stitched with matching thread. Trouser must be cleaned and finished to eliminate loose threads.

LABEL:

Trouser must have a care label, size label, and country of origin and fiber content label permanently attached to the garment BUTTONS/ZIPPERS/SNAPS:

YKK Zipper - #5 metal tooth zipper

PRYM Snap - #26L Antique Brass Anodized Black Metal Snap STOCK SIZES:

Trouser must be available in the following stock sizes:

XS – 4XL in short, regular and long COLORS:

Trouser must be available in the following colors:

Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

35 Propper ACU Coat Propper A TACS ACU Coat 65 35 Poly Cotton Ripstop Mil Add subdued name strips attached over the right Spec F5459 pocket, subdued cross rifles over the name strip and subdued star attached over left pocket SKU# FS459-38-379

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

The A-TACS ACU are sewn to military spec FQ/PD 04-04A. The A-TACS ACU are made from a Battle Rip 65% polyester / 35% cotton ripstop material. Hook and loop-faced patches can accomodate rank insignia, unit patch, and name tapes. The mandarin collar can be worn up or down, and the hook and loop sleeve cuff closure provides positive closure. A 3- slot pen pocket on the sleeve bottom and miximized shoulder pockets are designed to fit optimally with the OTV. Nametape and patches not included. A-TACS camo replaces traditional digital style square pixels with pixels that are organically shaped and small. This cam removes any and all 90 degree angles which means the A-TACS camo has an appearance that is more natural and fluid. The colors utilized by A-TACS are digitally sampled from real world elements which enhances the concealment ability of this camo pattern.A-TACS utilizes a unique design which creates a "pattern within a pattern". FABRICS:

The military fabric is a 65/35 Poly/Cotton Ripstop. This fabric is resistant to shrinking and is vat-dued to ensure a minimal amount of fading over the life of the garment.

COLOR:

A-TACS AU

SIZE: XSXS – XXLL

CHEST: 29-32 through 49-52

HEIGHT: 59-63 through 75-79

SLEEVE: 20 3/8 – 25 3/8

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

36 Propper ACU Trouser Propper A TACS ACU Pants Mil Spec 65 35 Poly Cotton Ripstop Need name strip over right rear pant pocket F5209

SKU# F5209-38-379

SPECIFICATIONS AND ESSENTIAL FEATURES SPECS:

Sewn to Military Specification FQ/PD 04-05A Leg Cuff with Front Closure Tie Forward-Tilted Cargo Pockets Button Fly with Drawstring External Knee Pouch with Hook and Loop Closure Vat-Died for Fade, Shrink and Wrinkle Resistance FABRICS:

The military fabric is a 65/35 Poly/Cotton Ripstop. This fabric is resistant to shrinking and is vat-dued to ensure a minimal amount of fading over the life of the garment.

COLOR:

A-TACS AU SIZE: XSXS – 4XLR

WAIST: 23-26 – 51-54

INSEAM: 23 ½ - 26 ½ through 35 ½ - 38 ½ LAUNDRY INSTRUCTIONS:

Machine wash, gentle cycle, with warm water. Cold water rinse. NO BLEACH. Hang dry, do not fold or store when wet. Maximum Shrinkage: Less than 1%.

DESCRIPTION ITEM # MANUFACTURER MODEL # 3-in-1 PARKA SAFETY-JACKET 37 5.11 TACTICAL 48001-019 Black SPEC./TAC

SPECIFICATIONS AND ESSENTIAL FEATURES: (See Item #30)

ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE

38 GORE-TEX® REVERSIBLE RAIN JACKET WITH Blauer # 9691 OPTIONAL # 9123 RAIN HOOD # 9123

Contractor shall include the following without additional cost to the City:

 SFPD’s cloth star (silver) with officer’s badge number embroidered in black thread (8 mm block font) sewn in place of left chest badge tab  The following shall be Silk Screened on the back of the garment in 3” Silver, reflective lettering “SFPD”

SPECIFICATIONS AND ESSENTIAL FEATURES

FABRIC:  Reversible waterproof, windproof, breathable 3-layer GORE-TEX® fabric  Convertible side pockets with waterproof zippers provide the convenience of equipment and weapon access from both hi-vis and dark sides of jacket  Seams sealed with GORE-SEAM® tape  Water-repellent treated on both hi-vis and dark sides  Double storm fly front with hook-and-loop fasteners  Sport collar zips to top  Adjustable cuff closures  2” SCOTCHLITETM reflective trim on hi-vis side around chest, back, cuffs, and sleeves  Badge tabs on left chest of both sides (optional)  31 1/2” long  Certified to ANSI/ISEA 107-2010 Class II  Optional upgrade to ANSI III with 2” reflective stripe added above hem Authorized for purchase under the Homeland Security Grant Program & Fire Act Grant as PPE TECHNOLOGY:  Blauer's B.BRIGHT® logo indicates a product is designed to provide additional visibility while on the job, and may be certified to an ANSI standard. B.BRIGHT® product attributes include body silhouetting and color-blocked designs, hi-visibility fabrics, and Scotchlite™ and other reflective materials.

 3M™ Scotchlite™ Reflective Material is recognized as the leading high performance retroreflective material for enhancing nighttime visibility by concentrating light from sources such as headlights and reflecting it back to the source.

Waterproof. Windproof. Breathable. GORE-TEX® fabric keeps you drier, warmer, and more comfortable in all types of weather. CERTIFICATION:

American National Standard for High-Visibility Public Safety Vests ANSI/ISEA was developed by the International Safety Equipment Association in response to concerns that American workers who are exposed to low visibility hazards are not wearing appropriate visibility-enhancing apparel. SIZE: XS, S, M, ML, XL, 2XL, 3XL, 4XL, 5XL, 6XL

LENGTH: SHORT, REG, & TALL

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

39 RAID JACKETS Law Pro made by Quartermaster JC 382

SPECIFICATIONS AND ESSENTIAL FEATURES JACKET

COLOR

Navy, JC 382 SIZE

Small, Medium, Large, X-large, XX-large to 5XL LETTERING

Silk-Screen:

Back: Six (6) inch silk screen, gold letters, centered with “POLICE”

Front: Two (2) inch silk screen, gold letters, right front breast pocket area with “POLICE”.

Three (3) inch silk screen, gold lettering, left front breast pocket are with “SFPD.” star,

Inserted with the words “San Francisco Police”. (Letters shall be all caps, block style.)

Sleeves: SFPD patches to be placed on each shoulder, centered, 1" from shoulder seam.

40 Fechheimer Brothers Company 78141 GORE-TEX WATERPROOF FOUL WEATHER JACKET

SPECIFICATIONS AND ESSENTIAL FEATURES OUTER SHELL:

Supplex supreme warp 70 denier nylon filling 3 ply 70 denier nylon. Weight 3.6 oz. per square yard. Weave: Plain. Tear strength warp 9.0 lbs. Filling-8.0 lbs. Tensile strength Warp-200 lbs. Fill-150 lbs. Abrasion (4 lb diaphragm, 1 lb head load): 300 COLOR:

BLACK LINING:

Gore-Tex material, waterproof, breathable lining or other porous fluoropolymer membrane (Teflon) coating. This membrane had about 9 billion pores per square inch (around 1.4 billion pores per square centimeter). Each pore is 1/20,000 the size of a water droplet, making it impenetrable to liquid water while still allowing the more autonomous water vapor molecules to pass through. It must pass the following:

CHARACTERISTIC REQUIREMENT TEST METHOD

Moisture Vapor

Transmission Rate (g/m²/24hr)

Procedure B 600 Minimum ASTM E 96-80

Procedure BW 5,000 Minimum ASTM E 96-80

Hydrostatic Resistance (psi) 90 Minimum FED-STD-191A 5512

Water Permeability

Initial No Leakage FED-STD-191A 5516

After Cold Flex

Warp No Leakage ASTM D 2097-69 (1980) Fill No Leakage

After 100 Hours of Continuous No Leakage AATCC 135

Wet Flex (agitation) FED-STD-191A 5516

After Dry Cleaning No Leakage FED-STD-191A 5516

After Synthetic Perspiration No Leakage Gore QCTM 510

FED-STD-191A 5516

After Sustained Pressure No Leakage BS 3424: Part 26:1990

Method 29A

After Sustained Pressure, Gore QCTM 552

After Exposure to No Leakage BS 3424: Part 26:1990

Contamination Method 29a

BASIC STYLING:

Waist length, single breasted, black Gore-Tex LTD breathable waterproof lining, or other porous fluoropolymer membrane (Teflon) coating that is free hanging. This membrane had about 9 billion pores per square inch (around 1.4 billion pores per square centimeter). Each pore is APPROXIIMATELY 1/20,000 the size of a water droplet, making it impenetrable to liquid water while still allowing the more autonomous water vapor molecules to pass through removable, Thinsulate body/sleeve liner, and front zipper storm front closure, bi- swing back, raglan sleeves, sleeve zippers, pocket flaps, inverted pleated patch pockets with hand warmer openings, collar, knit wind collar, shoulder straps, badge tab, zippered side vents with tab REMOVABLE LINER:

There shall be a zip-out insulated liner that incorporates CDS-200 Thinsulate® Thermal Insulation in the body portion of the liner and CDS-100 Thinsulate Thermal Insulation in the sleeves. The insulation shall be quilted to black 86-pick nylon on the face side of the liner and nylon tricot on the backing. There shall be black knit inserts placed under the arm of the liner sleeves 9" in length and 3 ½"at widest center point for comfort and ease of movement. The liner will attach to the jacket with a grip-lock non-run zipper.

SHELL FOR REMOVABLE LINER:

86 pick. 100% Nylon Taffeta. WEAVE-Plain. DENIER: Warp-70. Fill-70. WEIGHT 1.8 oz./square yard COLOR : Black (any other shade is cause for rejection). INSULATION:

3M Thinsulate, with a scrim covering front and back to prevent migration of insulation fibers. Lining must be quilted horizontally with a min of a 6” railroad pattern for max. thermo retention. Excess stitching and openings in liner cause extreme loss of body heat.

BODY:

Body - 3M Thinsulate CDS 200 composed of 65% Polyolefin microfibers and 35% 6 Denier Polyester staple fibers (by weight). Shall weigh 200 grams/square meter horizontally quilted SLEEVES:

3M Thinsulate CDS 100  Content: 65% Polyolefin microfibers 35% 6 Denier Polyester staple fibers  Material wt: 100grs/sq.m.  Liner: The perimeter of the liner shall be bound with black nylon taffeta tape and the liner shall have a black vislon zipper track to allow the liner to zip out of the jacket. The liner sleeves will have a female snap by the in sleeve seam no more than 1” from the end of the sleeve. The liner have a left breast patch pocket, each sleeve hem must be finished with bias tape so there are no raw edges. The liner shall be designed with vents corresponding with the zippered side vents on the jacket to allow easy access to weapon or equipment. Tab: Attached to the jacket sleeve, made of shell material with a make snap, the tab and snap are used to secure the liner sleeves. BACK:

One piece back with a bi-swing Bi-swing: 9” in length and 1 ½” in depth. It shall be constructed with an elasticized anchor so the bi-swing will snap back into proper position after being extended. It shall be constructed with an elasticized anchor made of a 2” wide strip of Lycra so the bi-swing will snap back into proper position after being extended INTERLINING:

 To be used in collar, pocket flaps, shoulder straps, front waistband, and storm front.  Material: 100% Cotton Osnaburg  DEF: Osnaburg was a coarse type of plain textile fabric, named for the city of Osnabrück (from which it may have been first imported into English-speaking countries). Originally made from flax yarns, it has been made from either flax, tow or jute yarns, sometimes flax or tow warp with mixed or jute weft, and often entirely of jute. The finer and better qualities form a kind of common sheeting, and the various kinds may contain from 20 to 36 threads per inch and 10 to 15 picks per inch. Material wt: 3.45 yds./lb POCKETS 7 ½” wide and 8” depth, there shall be an inverted pleated patch pocket on each front of the jacket.  On the side of the pocket: Pockets shall be constructed with hand warmer openings  Top part of the pocket: Will be black Kasha, the top and bottom of the side openings shall be securely bartacked.  Patch pocket: Will have an opening at the top underneath the flaps, the top of each patch pocket must be bound with black nylon binding, back of box pleated patch pocket must be fully lined. The Left front Pocket: Will have a pencil compartment opening on the inside corner of the pocket flap, the opening will be reinforced by bartacks.

 Pocket flaps: Have a metal snap closure system, the male portion of the snaps shall be located on the underside of each flap and the female portion of the snaps shall be in a corresponding location on the breast pocket. Each flap shall have a dummy buttonhole with a 24 ligne metal button on the top of the flap attached with a kotter key on the bottom side of the flap Inside left breast pocket: Min width of 6” and min depth of 8 ¼”, the inside pocket will incorporate a zipper closure system utilizing a 6” CFC-256B2 zipper that is made with bottom stops at both ends.

ELASTIC WAISTBAND Separate waistband shall be elasticized in the back.

 Spacing: 2 rows of stitching each ½” apart, centered on the waistband, and extending through the elastic.  Elastic: Shall be securely tacked at each end  Zipper: Be sewn into each side for access.  Elasticized tabs: Be sewn into the waistband for closure of the side tab Belt keeper tab: 2 belt keeper tabs, with sewn eyelets, made of shell fabric and located 2” from back zipper side vents SLEEVES:

3 pieces, raglan style sleeves with cuffs. The top half of the cuff must be elasticized and the bottom half to close with a tab and double snap for cuff adjustment. The sleeves shall be constructed with 7” zippers on the underseams. The attachment without puncturing the Gore-Tex or other porous fluoropolymer membrane (Teflon) coating that is free hanging to a fabric. This membrane had about 9 billion pores per square inch (around 1.4 billion pores per square centimeter). Each pore is ,000 the size of a water droplet, making it impenetrable to liquid water while still allowing the more autonomous water molecules to pass through .by allowing access to the shell is permitted. COLLAR:

2 plies of the shell fabric plus the interlining  Ply: all plies to be cut on bias  Interlining: Be sewn to the undercollar  Collar point: Shall be well shaped and symmetrical Under collar: To be constructed to conceal a removable Gore-Tex . Hood or other porous fluoropolymer membrane (Teflon) coating that is bonded to a fabric. This membrane had about 9 billion pores per square inch (around 1.4 billion pores per square centimeter). Each pore is 1/20,000 the size of a water droplet, making it impenetrable to liquid water while still allowing the more autonomous water vapor molecules to pass through. EPAULETS:

Measuring 2 ½” at the widest point and tapering to 1-3/4” at the narrow end, fastened with a 24 ligne metal uniform button and buttonhole, shoulder strap to be cross-stitched and sewn down.

STORM FLAP There shall be a double front storm flap  Top storm flap: 2 ¾” wide and will extend from the bottom of the waistband to the top of the collar point  Metal snaps: There shall be 6 black gun metal snaps centered down the top storm flap  Under storm flap: 2” wide and will extend from the bottom of the waistband to the top of the collar point  Male portion of the snaps: Shall be positioned on the under storm flap to correspond to the placement of the snaps on the top storm flap to provide a neat and secure closure Center of snap: To be plugged, concealing open portion of snap SIDE VENTS The jacket shall be designed with side vents to allow for easy access to equipment  The vent: Shall incorporate 10” zippers Bottom of each vent: There shall be an elasticized tab and snap closure system to prevent gaping between the front and rear portion of the jacket when the side zipper are in the full upward position WEEP EYELETS To have black metal 1/8” weep eyelets located at the bottom of sleeve (both panels) and front and back body panels. BADGE TAB To be made of self material with 2 metal eyelets The bottom of the badge tab: Shall be 2 ¼” – 2 ½” above the left pocket flap FRONT ZIPPER The front zipper opening shall be accomplished with a two way pull, heavy-duty # 5 nylon modeled zipper, and extend from bottom of waistband to collar seam.

KNIT WIND COLLAR  Knit wind collar: 1x1 ribbed spun nylon sewn into the collar seam Collar seam: Measuring 14” long (for size Large) by 1 ½ wide at the center SEAM WATERPROOFING Seams shall be taped with 7/8” two layer Gore tape or other porous fluoropolymer tape (Teflon) seam tape. There shall be no stitching through the LTD liner except those seams that are waterproofed. There will be metal eyelets on the sleeve bottoms and above the front and back waistband, for water drainage in laundering

SIZE TAG AND CARE INSTRUCTIONS:

The jacket shall have a sewn in label giving care instructions and a permanent woven size tag. The jacket shall also have a label indication lot number, size, fiber content, and RN number. +

SIZE RANGE:

The jacket must be available in the following sizes:

Regular: S-4XL Short: S-L

Long: S-3XL

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

41 WINDBREAKER REVERSIBLE NYLON BLACK Fechheimer 73161 JACKET

SPECIFICATIONS AND ESSENTIAL FEATURES MODEL NUMBER:

Reversible High Visibility Jacket shall be Flying Cross by Fechheimer Company #73161.. FABRIC  Outer shell: 100% nylon 3-ply Supplex Lining (reversible side): 100% Polyester high-visibility fluorescent yellow BASIC DESIGN Jacket to have windproof, waterproof, and breathable membrane with all seams properly sealed and shall meet ANSI standard. It shall be full cut with a butted reversible molded plastic zipper to the top of collar COLLAR Collar facing to extend to top edge of upper reflective stripe on the fluorescent yellow side  Collar points: Shall be well shaped and symmetrical, the collar shall be top stitched with collar points long enough for a neat appearance  Permanent collar and collar stand: Shall be made of 2 plies of the basic fabric plus the interlining  Collar interlining: Shall be sewn to the under collar and the under collar stand Top of collar: With a black molded plastic reversible zipper

BODY DESIGN  The fronts: Shall be plain with patch pockets measuring 6 ¾” wide by 7” deep with top edge of pocket turned in and finished ¾” so there are no raw edges  Pleat: Inverted pleat shall be 1 ½” wide. Pleat shall be sewn to open 4”  Side opening of pocket: 5” to allow access to the hand warmer compartment/pocket  Flap: 7 ¼” across, 2 ¼” at each side, and 3” at center point where there shall be a horizontally positioned dummy buttonhole to accommodate a 24ligne SFPD metal button. Flap and pocket are to have small snaps at each end to close separate top opening compartment/pocket. Left pocket flap to have hidden pen opening on left side 1 ½” wide, bartacked at each side Black metal eyelets: There shall be 4 weep holes on navy side, at front and back of jacket, both sides, 1 ¾” from side zippered vents WAISTBAND Separate waistband shall measure 2 ¼”, plain across the front, elasticized across the back with 2 rows of stitching through the center Spacing: 2 rows of stitching each ½” apart, centered on the waistband, and extending through the elastic.  Side zipper vents: Shall be butted and finish 9 ½” long  Zipper: Black nylon reversible  Elasticized tabs: 3 ½” long by 1” wide and to snap on the front of jacket Additional snap: Shall be positioned 1 ¼” towards back of jacket waistband to hold tab in place if not utilized by wearer SLEEVES Shall be 2 piece modified raglan style with 8” nylon zipper on black side to allow for access inside coat for emblem sewing  The bottom: Shall have a 2” cuff, elasticized shirred with 3 rows of stitching across the back, with 1 ½” wide by 2 ½” long tab on front side of cuff with Velcro for adjustable closure  Loop side of Velcro on cuff: 4” long by 1” wide and to attach to hook side of Velcro on bottom side of tab 1 ½” long by 1” wide Back metal eyelets: There shall be 2 weep holes spaced 1” from cuff on front and back sides of sleeves EPAULETS To be 1 ¾” wide tapering slightly to a point, cross stitched, and permanently inserted into armhole. Pointed end of shoulder strap to be tacked in place. There shall be a horizontally positioned dummy buttonhole to accommodate a 24 ligne SFPD metal button SILVER REFLECTIVE TAPE (REVERSIBLE LINING SIDE):

ANSI 2 standard silver reflective tape shall be placed on the fluorescent yellow side of jacket. All silver reflective tape to be 2” wide with black edge. There shall be two rows on body of coat and sleeves. The top row on the body of coat to be positioned 1” down from armhole and bottom row to be up 1” from waistband and shall continue around back of jacket with stripes on back lining up with stripes on front. Sleeves to also have two rows of reflective tape positioned so that top row is 5” down from armhole and bottom row to be 4” from cuff. Tape on sleeves to line up at sleeve seams. Both rows of reflective tape on body shall line up at butted front zipper closure. Reflective 3” SFPD letters shall be heat sealed to the high visible side of the jacket in the back center, at the factory, as in previous garments.

BADGE TAB(S):

Both sides of jacket to have badge tab coordinating with color/fabric. To be positioned on left breast measuring 2-1/2" long by 7/8" wide with 2 metal eyelets 1-1/4" apart, center to center. INTERLININGS: Front opening, collar, pocket flaps, cuffs, epaulets, and waistband to be interlined with pellon. FINISHING & PRESSING:

The entire jacket must be made in a first class manner. Industrial construction will not be acceptable. All loose threads must be removed and jacket must be completely pressed with proper pressing equipment and properly shaped. STOCK SIZES:

To be available from stock in the following sizes:

Regulars – XS to 5XL

Longs – M to 5XL

Extra Longs – L to 4XL

ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE

MOTOR OFFICER JACKET Tourmaster Flex Jacket LE2

COLOR: Black

FEATURES:  Converts easily from a 600 denier Carbolex® Jacket to an Armor-Link mesh jacket and vice-versa  Water-resistant outer jacket incorporates waterproof zippered sleeve vents  360º Phoslite® reflective piping and Tour Master’s signature reflective rear triangle help increase nighttime visibility  Soft, durable microfiber-lined collar and cuff  Adjustable sleeve takeup straps to secure elbow armor and material  Removable, CE approved armor at the elbows and shoulders with an articulated triple density back protector  Tour Master’s Z.O.Q. (Zip-Out Quilted) Liner features warming 100gm polyfill insulation  Zippered hand pockets, internal pouch pocket and mobile media pocket  Adjustable waist belts with TPR pulls help to fine tune the fit  Includes a jacket/pant zipper attachment with the pant side included  Zippered air vents  Badge and mic holder  Outer to Inner shell conversion STOCK SIZES: Men’s XS-4XL, Ladies XS-XL

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

43 Patrol Otto-Cap N/A Baseball Cap 27-210

SPECIFICATIONS AND ESSENTIAL FEATURES Features

FEATURES

 15% Wool 85% Acrylic: The Professional Look / Structured / Firm Front Panel  6-panel cap  Seamed Front Panel with Full Buckram  6 Embroidered Eyelets  Pro Stitch on Crown  8 Rows Stitching on Visor  Matching Color Undervisor  Matching Color Sweatband  Plastic Adjustable Snap

Embroidery Specification:

 2.16 H x 4.41 W  “SAN FRANCISCO POLICE” Shall be embroidered in ½” Block, capital lettering in Madeira 1024 Gold Thread at no additional cost to the City.

SIZE:

Adjustable

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

44 Range Otto-Cap No photo Baseball Cap 27-210

SPECIFICATIONS AND ESSENTIAL FEATURES Features

FEATURES

Embroidery Specification:

 2.16 H x 4.41 W  “SAN FRANCISCO POLICE” Shall be embroidered in ½” Block, capital lettering in Madeira 1024 Gold Thread at no additional cost to the City.

COLOR:

Red

SIZE:

Adjustable

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

45 EVOC Otto-Cap Need photo Baseball Cap 27-210

SPECIFICATIONS AND ESSENTIAL FEATURES Features

FEATURES

Embroidery Specification:

 2.16 H x 4.41 W  “SAN FRANCISCO POLICE” Shall be embroidered in ½” Block, capital lettering in Madeira 1024 Gold Thread at no additional cost to the City.

COLOR:

Red

SIZE:

Adjustable

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

46 Academy PT/DT Tshirt D&J Enterprises TS848 NAV (Galls)

SPECIFICATIONS AND ESSENTIAL FEATURES

To be screenprinted with Academy star on front (see photo), Last name in all Caps on the back. COLOR

Navy with yellow/gold screenprint SIZE

Small, Medium, Large, X-large, XX-large to 5XL

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

47 Academy PT/DT Shorts D& J Enterprises TT594 NAV (Galls) N/A

SPECIFICATIONS AND ESSENTIAL FEATURES COLOR

Navy SIZE

Small, Medium, Large, X-large, XX-large to 5XL

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

48 Academy PT/DT Fleece jacket zip up D&J Enterprises SM226 NAV (Galls) N/A

SPECIFICATIONS AND ESSENTIAL FEATURES COLOR

Navy, SIZE

Small, Medium, Large, X-large, XX-large to 5XL

100

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE 85R54 http://www.galls.com/flyi 49 Flying Cross ng-cross-men-s-polyester- cotton-short-sleeve- Academy shirt (men’s) shirt?PMSRCH=sh020

SPECIFICATIONS AND ESSENTIAL FEATURES

With Academy patch on left and right sleeve COLOR

Light blue

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE 176R54 http://www.galls.com/flyi 50 Flying Cross ng-cross-women-s- polyester-cotton-short- Academy shirt (women’s) sleeve- shirt?PMSRCH=sh047 SPECIFICATIONS AND ESSENTIAL FEATURES

With Academy patch on left and right sleeve

COLOR

Light blue

101

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

51 Galls Tie UA521

SPECIFICATIONS AND ESSENTIAL FEATURES Features

Clip COLOR:

Black SIZE:

Short/ Regular/ 16”/ Long

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

52 Red Kap Poly cotton trousers Academy trousers Galls TR022

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC:

8 oz. 65% polyester/35% combed cotton twill

102

COLOR:

Navy Blue POCKETING:

Darts over hip pockets for better fit

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

53 Marine Unit Tactical Fleece 5.11 Black Tactical Fleece Model 48038-019

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC: All-weather fleece

FEATURES:

Reinforcements at collar, shoulders, and elbows

Mike clips at each shoulder

Zippered handwarmer pockets

Hidden chest pockets SPECIAL CONDITIONS:

To include 2 each subdued shoulder patches, embroidered subdued star, embroidered last name tape (subdued), collar/shoulder rank insignia (subdued) COLOR:

Black

103

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Marine Unit Flotation Jacket with Reflective Tape Mustang Survival MJ6214 T1 54

SPECIFICATIONS AND ESSENTIAL FEATURES FEATURES:

62 square inch of reflective tape

Neoprene wrist seals

Pen pocket on right sleeve

Four front pockets, 1 large pocket on inside of jacket

Full length storm flap

Internal waist belt

USCG-UL1123 approval for Marine Buoyant devices SPECIAL CONDITIONS:

To include: shoulder patches, embroidered star patch (rank dependent color/style, Velcro-attached), embroidered last name tape (rank dependent color, Velcro attached), collar/shoulder rank insignia (rank dependent color), embroidered crossed oars & life-ring centered above name (rank-dependent color, direct embroidery), embroidered dive helmet for certified Unit divers only centered on right pocket flap (silver, direct embroidery) COLOR:

Black

104

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Grundens GAGE Burning Daylight Hooded Jacket in 55 Marine Grade hooded rain jacket BD300B black

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC: Heavy duty 10,000 mm waterproof material with fully taped seams FEATURES:

Secure storage pockets, 10,000mm waterproof, 5,000 mvp breathable fabric, two exterior chest pockets, interior mesh stuff pocket COLOR:

Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

56 Marine Grade rain pant with suspenders Grundens GAGE Burning Daylight pant in black BDT101BB

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC: 10,000 mm waterproof material with fully taped seams

FEATURES:

10,000mm waterproof, 5,000mvp breathable fabric, fully taped and sealed seams, reinforced knees, zippered handwarmer pockets, adjustable leg cuffs, removable adjustable suspenders. COLOR: Black

105

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

57 Richardson K-9s/Specialized Units 585 fitted baseball cap Galls HW851 N/A

http://www.richardsoncap.com/capmodel/585

SPECIFICATIONS AND ESSENTIAL FEATURES Specifications:

Fitted cap (no adjustable plastic band)

Embroidered “San Francisco Police K-9 Unit” in silver embroidery for navy cap or subdued embroidery for black cap

COLOR:

Navy, Black

ITEM # DESCRIPTION CURRENT MANUFACTURER CURRENT MODEL # IMAGE

5.11 WATERPROOF Patrol Rain PANTS 5.11 TACTICAL 48057 58

COLOR: Black

106

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

59 HI-VIS B. DRY RAIN PANTS BLAUER 134-1 (PSA and Security Guard)

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC:  B.DRY® waterproof, windproof, breathable laminate on durable polyester shell fabric.  Elasticized drawcord waistband with side openings.  Seams sealed with thermal tape.  Side openings provide access to trouser pockets. Hi-vis certified to ANSI 107-2010 Class E certified with double 2” SCOTCHLITE ™ brands above hem.

COLOR:

Hi-vis Yellow SIZE:

XS thru 6XL, in short, regular and tall lengths.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

60 Raeford #970233 UNIFORM CAP FOR SFPD OFFICER 8-Point Style

107

SPECIFICATIONS AND ESSENTIAL FEATURES MATERIAL:

Raeford Uniform Fabrics Company’s Style No. 13507-2135 Wool, kiss bonded with foam and tricot lining

STYLE:

8-point style. MEASUREMENTS: Size 7-1/8 – 7-1/4. Crown from point to point 11", front height 2-1/4", back height 1-3/4". Measurements of other sizes to be proportion.

COVER:

Will include top, projection, side band, tip lining (black acetate), sweatshield (.008 gauge clear vinyl) and a pocket for individual name card. Seams will lockstitched, 10 to 12 stitches to the inch. FRAME:

The construction shall be #9820 black visor, front band, and stayer of solid black. Emblem slots and assembly holes to the preformed, the inner band 2-1/8" x .050" extruded "poly" perforated with 3/8" holes throughout, with pre-punched button holes and attached with brass rivets. Black soutache top and bottom of band.

GROMMET:

Galvinized piping wire #2 attached to front stayer by (3) brass rivets.

SWEATBAND:

27 oz. anti-migratory non-toxic cloth backed vinyl, sewn on the outside of inner band and turned for cushioned effect to provide maximum confort, Top edge to be finished and size label attached. Each cap to effectively cover (2) head sizes. EYELETS:

Each cap provided with a front badge eyelet and (2) ventilating eyelets on each side.

108

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

61 Raeford #970233-D UNIFORM CAP FOR SFPD LIEUTENANT 8-Point Style

SPECIFICATIONS AND ESSENTIAL FEATURES MATERIAL:

Raeford Uniform Fabrics Company’s Style No. 13507-2135 Wool, kiss bonded with foam and tricot lining

STYLE:

8-point style. MEASUREMENTS: Size 7-1/8 – 7-1/4. Crown from point to point 11", front height 2-1/4", back height 1-3/4". Measurements of other sizes to be proportion.

COVER:

GROMMET:

Galvinized piping wire #2 attached to front stayer by (3) brass rivets.

109

SWEATBAND:

Each cap provided with a front badge eyelet and (2) ventilating eyelets on each side.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

62 Raeford #970233-C UNIFORM CAP FOR SFPD COMMANDER 8-Point Style

SPECIFICATIONS AND ESSENTIAL FEATURES MATERIAL:

Raeford Uniform Fabrics Company’s Style No. 13507-2135 Wool, kiss bonded with foam and tricot lining

STYLE:

8-point style. MEASUREMENTS: Size 7-1/8 – 7-1/4. Crown from point to point 11", front height 2-1/4", back height 1-3/4". Measurements of other sizes to be proportion.

COVER:

110

FRAME:

GROMMET:

Galvinized piping wire #2 attached to front stayer by (3) brass rivets.

SWEATBAND:

Each cap provided with a front badge eyelet and (2) ventilating eyelets on each side.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

63 Raeford #970233-B UNIFORM CAP FOR SFPD CHIEF 8-Point Style

SPECIFICATIONS AND ESSENTIAL FEATURES MATERIAL:

Raeford Uniform Fabrics Company’s Style No. 13507-2135 Wool, kiss bonded with foam and tricot lining

STYLE:

8-point style.

111

MEASUREMENTS: Size 7-1/8 – 7-1/4. Crown from point to point 11", front height 2-1/4", back height 1-3/4". Measurements of other sizes to be proportion.

COVER:

GROMMET:

Galvinized piping wire #2 attached to front stayer by (3) brass rivets.

SWEATBAND:

Each cap provided with a front badge eyelet and (2) ventilating eyelets on each side.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

64 DRESS SHIRT, LONG SLEEVE, TAN POLY/RAYON Flying Cross by Fechheimer 19W6604 (MEN’S)

(AIRPORT BUREAU)

SPECIFICATIONS AND ESSENTIAL FEATURES

112

MILL Burlington 8130 FABRIC:

Content: All synthetic tropical weave 65% Dacron Polyester/35% Rayon conforming to

the following specifications:

Weight: 6.6 oz./sq. yd.

Construction: 49 warp X 36 filling yarns per sq. inch. All yarns size 10/1 singles

Air Permeability: Ft. 3/Min/Ft. 2 131 ASTM D 737-46

Tensile: Break Strength 105 warp - 90 filling (lbs.)

Properties: Tear Strength 9.7 warp - 8.5 filling (lbs.)

Pilling: Minimum 4.9 rating COLOR: Silver Tan #1985 STYLE: Dress style, top center placket front, full cut tapered fit, banded collar, long sleeves with barrel cuffs, and dress shirttail. Two plain breast pockets with topstitched scalloped flaps. Topstitched epaulets. Exterior badge holder with metal eyelets. Matching inside yoke and collar band of Dacron/Cotton Poplin. Work wear industrial style shirt construction is unacceptable and shall be cause for rejection. Flying Cross by Fechheimer Lot 19W6604.

COLLAR  Collar points: 3” long  Plastic stays: Fused-in Mylar stays (or equivalent)  Collar rear: 1-1/2” Collar stand: 1-5/16” at rear and band to be die cut and interlined with stabilized Mello Press (#285 in collar, “Crease N Tack” or #250 Dacron Polyester in band). Top enter interlined with # 550 Mello Press. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16” raised stitch. Safety stitch joining unacceptable

113

FRONT  Buttons: First grade 22 ligne melamine  Inside Yoke and Collar band lined with Poly/Cotton Poplin to match  Button spacing: The shirt will have 7 buttons and buttonholes on the front, spacing between each will be 3 3/4” except the spacing between the neck button and the first button on the front which will be 3¼” Placket: The left front shall have a top center 1 ¾” wide with two rows of stitches 7/8” apart EPAULETS Asymmetrical shape topstitched ¼” off the edge to be set on yoke with leading topstitch conforming with front joining seam. To measure 2” at sleeve tapering to 1 3/8” and set not more than ½” from folded collar. Cross stitched 2” from sleeve seam. Creased and edge stitched epaulet construction unacceptable

BADGE REINFORCEMENT  Exterior holder: 1 1/8” wide by 2 ¼” deep 2 metal eyelets: Spaced 1 ¼” apart with bottom eyelets centered 1 ½” above left flap. POCKETS 2 Plain breast pockets  Measure: 5 5/8” wide, 6” deep  Left breast pocket: 1 ½” pencil stitch Position: Each pocket to have Velcro tape ¾” long by ½” wide positioned on both edges of the pocket to correspond with outer scalloped flap points as sample.

FLAPS  Design: Deep scalloped  Measure: 5 7/8” across, 2 ¾” in depth at center point, 2 ¼” at sides. Topstitched ¼” off the edge and secured to shirt front ¼” above pocket  Left flap: To have invisible pencil opening 1 ½” to correspond precisely with pencil slot of pocket  Both flaps: To be interlined with #550 stabilized Mello Press Creased and edge stitched pocket flap construction unacceptable Underside of the flap: To have Velcro tape ¾” long by ½” wide positioned on outer points of both pocket flaps as sample SLEEVES To be long sleeves cut straight and whole with 5 ½” sleeve vent  Elbow reinforcement: Shall extend into the sleeve closing seam  Lower facing: Shall measure ½” in width  Cuff: To measure 3” with rounded corners with ¼” topstitching 2 buttons: With corresponding buttonholes on each cuff and one button and buttonhole in the sleeve facing

114

CUFFS:

Two piece ½-inch hemmed cuff with ¼” topstitching. Cuffs to measure 3" in depth with rounded corners (barrel). Cuffs to have two buttons and corresponding buttonholes set vertically with one button and buttonhole in center of facing. Cuffs to have woven interlining of #550 Stabilized Mello-Press.

BUTTONS:

First grade 22-ligne melamine. STITCHING: To have single needle stitching throughout the shirt. All topstitched 1/4" off the edge. Sleeve inserting and side close felling safety stitched.

THREAD: All sewing threads to be fast color polyester core polyester wrap to match. MILITARY CREASES 5 Lintrak creases or equivalent silicone military creases on all shirts  Front: 1 crease on each front to be centered vertically through pocket and flap Spacing for three military creases across shirt back to be proportionate to the size of the shirt. STOCK SIZES:

Shirts must be available in the following sizes:

Sleeve lengths: 32-37 inches; Neck sizes: 14-1/2 to 18-1/2, 19, 20, 21, 22

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

65 DRESS SHIRT, SHORT SLEEVE, TAN POLY/RAYON Flying Cross by Fechheimer 69R6604 (MEN’S)

(AIRPORT BUREAU)

115

SPECIFICATIONS AND ESSENTIAL FEATURES MILL Burlington 8130 MATERIAL WEIGHT 6.6 oz / sq. yd. FABRIC:

Content: All synthetic tropical weave 65% Dacron Polyester/35% Rayon conforming to the following specifications:

Weight: 6.6 oz./yd. 2

Construction: 49 warp X 36 filling yarns per sq. inch All yarns size 10/1 singles

Air Permeability: Ft. 3/Min/Ft. 2 131 ASTM D 737-46

Tensile: Break Strength 105 warp - 90 filling (l

Properties: Tear Strength 9.7 warp - 8.5 filling (lbs.)

Pilling: Minimum 4.9 rating COLOR: Silver Tan #1985 STYLE:

Dress style, top center placket front, full cut tapered fit, convertible collar, short sleeves, and dress shirttail. Two plain breast pockets with topstitched scalloped flaps. Topstitched epaulets. Exterior badge holder with metal eyelets. Matching inside yoke of Dacron/Cotton Poplin. Work wear industrial style shirt construction is unacceptable and shall be cause for rejection. Flying Cross by Fechheimer #69R6604.

COLLAR: Convertible collar shall be 1 piece  Collar points: 3” long  Plastic stays: Fused-in Mylar stays (or equivalent) Collar to be topstitched ¼” off the edge, to be interlined with #285 Mello Press. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16” raised stitch. Safety stitch joining unacceptable

116

FRONT:  Buttons: First grade 22 ligne melamine  Inside Yoke lined with Poly/Cotton Poplin to match  Button spacing: The shirt will have 7 buttons and buttons on the front, spacing between each will be 3 ¾” except the spacing between the neck button and the first button on the front which will be 3 ¼” Placket: The left front shall have a top center 1 ½” wide with 2 rows of stitches 7/8” apart. Stitching on the top center is not to be visible on the turn-back facing EPAULETS: Asymmetrical shape top stitched ¼” off the edge to be set on yoke with leading topstitch conforming with front joining seam. To measure 2” at sleeve tapering to 1 3/8” and set not more than ½” from folded collar. Cross stitched 2” from sleeve seam. Creased and edge stitched shoulder strap construction unacceptable

BADGE REINFORCEMENT Exterior holder to finish 1-1/8” wide x 2” deep with 2 metal eyelets spaced 7/8” apart with bottom eyelet centered 7/8” above left lap POCKETS 2 Plain breast pockets  Measure: 5 5/8” wide, 6” deep  Left breast pocket: 1 ½” pencil stitch Position: Each pocket to have Velcro tape ¾” long by ½” wide positioned on both edges of the pocket to correspond with outer scalloped flap points as sample. FLAPS  Design: Deep scalloped  Measure: 5 7/8” across, 2 ¾” in depth at center point, 2 ¼” at sides. Topstitched ¼” off the edge and secured to shirt front ¼” above pocket  Left flap: To have invisible pencil opening 1 ½” to correspond precisely with pencil slot of pocket  Both flaps: To be interlined with #550 stabilized Mello Press Creased and edge stitched pocket flap construction unacceptable Underside of the flap: To have Velcro tape ¾” long by ½” wide positioned on outer points of both pocket flaps as sample

SHORT SLEEVES Sleeves are to be straight and whole, to have ¾” hem and to finish 9” long from shoulder seams BUTTONS:

First grade 22-ligne melamine. STITCHING: Collar, epaulets and pocket flaps to be topstitched 1/4" off the edge. Sleeve inserting and side close felling seams are to be safety stitched.

117

THREAD: All sewing threads to be fast color polyester core polyester wrap to match. INTERLININGS:

Collar interlined with #285 Stabilized Mello-Press. Pocket flaps and top center to be interlined with #550 Stabilized Mello-Press. MILITARY CREASES 5 Lintrak creases or equivalent silicone military creases on all shirts  Front: 1 crease on each front to be centered vertically through pocket and flap Spacing for three military creases across shirt back to be proportionate to the size of the shirt. MILITARY CREASES: Five silicone military creases on all shirts. One crease on each front to be centered vertically through pocket and flap. Spacing for military creases on shirt back to be proportionate to the size of the shirt as follows: sizes 14 thru 15 1/2 - creases to be 4 3/4" apart; sizes 16 thru 18, inclusive - creases to be 5 3/8" apart as measured from the center crease. CONSTRUCTION Collars, flaps and shoulder straps are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched STOCK SIZES:

Shirts must be available in the following sizes:

Neck sizes: S – 4XL

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

66 DRESS SHIRT, LONG SLEEVE, TAN POLY/RAYON Flying Cross by Fechheimer 103W6604 (WOMEN’S)

(AIRPORT BUREAU)

SPECIFICATIONS AND ESSENTIAL FEATURES MILL Burlington 8130

118

COLOR Silver Tan #1985 FABRIC: Content: All synthetic tropical weave 65% Dacron Polyester/35% Rayon conforming to the following specifications: Weight: 6.0 - 6.6 oz./yd. 2 Construction: 49 warp X 36 filling yarns per sq. inch All yarns size 10/1 singles Air Permeability: Ft. 3/Min/Ft. 2 131 ASTM D 73746 Tensile: Break Strength 105 warp 90 filling (lbs.) Properties: Tear Strength 9.7 warp 8.5 filling (lbs.) Pilling: Minimum 4.9 rating STYLE: To be Flying Cross Model 103W6604. Dress style, top center placket front, full cut tapered fit, banded collar, long sleeves with barrel cuffs, and dress shirttail. Two plain breast pockets with topstitched scalloped flaps. Topstitched epaulets. Exterior badge holder with metal eyelets. Matching inside yoke and collar band of Dacron/Cotton Poplin. Work wear industrial style shirt construction is unacceptable and shall be cause for rejection.

COLLAR:  Collar points: 2 7/8” long  Plastic stays: Fused-in OR SEWN-IN Mylar stays (or equivalent)  Collar rear: 1-1/2” Collar stand: 1-5/16” at rear and to be interlined with stabilized #285 Mello Press and “ Crease N Tack” or #250 Dacron Polyester in band, top center interlined with #550 Mello Press. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16” raised stitch. Safety stitch joining unacceptable FRONT  Buttons: First grade 22 ligne melamine  Inside Yoke and Collar band lined with Poly/Cotton Poplin to match  Button spacing: The shirt will have 6 buttons and buttonholes on the front, spacing between each will be 3 ½” except the spacing between the neck button and the first button on the front which will be 3¼” Placket: The right front shall have a top center 1 ½” wide with two rows of stitches 7/8” apart EPAULETS:

Asymmetrical shape top stitched ¼” off the edge to be set on yoke with leading topstitch conforming with front joining seam. To measure 2” at sleeve tapering to 1 3/8” and set not more than ½” from folded collar. Cross stitched 2” from sleeve seam. Creased and edge stitched shoulder strap construction unacceptable

119

BADGE REINFORCEMENT:

 Exterior holder: 1 1/8” wide by 2 ¼” deep 2 metal eyelets: Spaced 1 ¼” apart with bottom eyelets centered 1 ½” above left flap. POCKETS:

2 Plain breast pockets  Measure: 5” wide, 5” deep Position: Each pocket to have Velcro tape ¾” long by ½” wide positioned on both edge of pocket to correspond with outer scalloped flap points. FLAPS:

 Design: Deep scalloped  Measure: 5 ¼” across, 2 ¼” in depth at center point, 1 ¾” TO 2” at sides. Topstitched ¼” off the edge and secured to shirt front ¼” above pocket  Left flap: To have invisible pencil opening 1 ¼” wide  Both flaps: To be interlined with #550 stabilized Mello Press Creased and edge stitched pocket flap construction unacceptable Underside of the flap: To have Velcro tape ¾” long by ½” wide positioned on outer points of both pocket flaps as sample SLEEVES:

To be long sleeves cut straight and whole with 4 ½” sleeve vent  Elbow reinforcement: Shall extend into the sleeve closing seam Lower facing: Shall measure ½” in width CUFFS:

Two piece ½-inch hemmed cuff with 1/4" topstitching. Cuffs to measure 2 1/2" in depth with rounded corners (barrel cuffs). Cuffs to be two button adjustable. Cuffs to have woven interlining of #550 Stabilized Mello-Press. BUTTONS:

First grade 22-ligne melamine. STITCHING:

Single needle stitching throughout the shirt. All topstitched 1/4" off the edge. Sleeve inserting and side close felling safety stitched THREAD:

All sewing threads to be fast color polyester core polyester wrap to match.

120

MILITARY CREASES: 5 Lintrak creases or equivalent silicone military creases on all shirts  Front: 1 crease on each front to be centered vertically through pocket and flap. Spacing for three military creases across shirt back to be proportionate to the size of the shirt. CONSTRUCTION:

Collars, flaps and epaulets are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched. SIZES:

Shirts must be available in the following sizes:

Bust sizes: 28-52 Sleeve lengths: 28, 30 Regular = 30”

32, 34 Regular = 30” Long = 31”

36, 38 Regular = 31” Long = 32”

40, 42 Regular = 32” Long = 33”

44, 46 Regular = 33” Long = 34”

48 & Up Regular = 34” Long = 35”

121

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

67 DRESS SHIRT, SHORT SLEEVE, TAN POLY/RAYON Flying Cross by Fechheimer 153R6604 (WOMEN’S)

(AIRPORT BUREAU)

SPECIFICATIONS AND ESSENTIAL FEATURES MILL Burlington 8130 FABRIC: Content: All synthetic tropical weave 65% Dacron Polyester/35% Rayon conforming to the following specifications: Weight: 6.6 oz./yd. 2 Construction: 49 warp X 36 filling yarns per sq. inch All yarns size 10/1 singles Air Permeability: Ft. 3/Min/Ft. 2 131 ASTM D 73746 Tensile: Break Strength 105 warp 90 filling (lbs.) Properties: Tear Strength 9.7 warp 8.5 filling (lbs.) Pilling: Minimum 4.9 rating COLOR: Silver Tan #1985 STYLE: Dress style, top center placket front, full cut tapered fit, convertible collar, short sleeves, and dress shirttail. Two plain breast pockets with topstitched scalloped flaps. Topstitched epaulets. Exterior badge holder with metal eyelets. Matching inside yoke and banana band of Dacron/Cotton Poplin. Work wear industrial style shirt construction is unacceptable and shall be cause for rejection. To be Flying Cross #153R6604.

122

COLLAR: Convertible collar shall be 1 piece  Collar points: 2 7/8” long  Plastic stays: Fused-in Mylar stays (or equivalent) Collar to be topstitched ¼” off the edge, to be interlined with #285 Mello Press. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, then all three are stitched down with a 1/16” raised stitch. Safety stitch joining unacceptable FRONT:  Buttons: First grade 22 ligne melamine  Inside Yoke lined with Poly/Cotton Poplin to match  Button spacing: The shirt will have 6 buttons and buttons on the front, spacing between each will be 3 ½” except the spacing between the neck button and the first button on the front which will be 3 ¼” Placket: The right front shall have a top center 1 ½” wide with 2 rows of stitches 7/8” apart. Stitching on the top center is not to be visible on the turn-back facing EPAULETS: Asymmetrical shape top stitched ¼” off the edge to be set on yoke with leading topstitch conforming with front joining seam. To measure 2” at sleeve tapering to 1 3/8” and set not more than ½” from folded collar. Cross stitched 2” from sleeve seam. Creased and edge stitched shoulder strap construction unacceptable

BADGE REINFORCEMENT: Exterior holder to finish 1-1/8” wide x 2” deep with 2 metal eyelets spaced 7/8” apart with bottom eyelet centered 7/8” above left flap

POCKETS: 2 Plain breast pockets  Measure: 5” wide, 5” deep Position: Each pocket to have Velcro tape ¾” long by ½” wide positioned on both edge of pocket to correspond with outer scalloped flap points. FLAPS:  Design: Deep scalloped  Measure: 5 ¼” across, 2 ¼” in depth at center point, 1 ¾” at sides. Topstitched ¼” off the edge and secured to shirt front ¼” above pocket  Left flap: To have invisible pencil opening 1 ¼” wide  Both flaps: To be interlined with #550 stabilized Mello Press Creased and edge stitched pocket flap construction unacceptable Underside of the flap: To have Velcro tape ¾” long by ½” wide positioned on outer points of both pocket flaps as sample SHORT SLEEVES: Sleeves are to be straight and whole, to have 3/4" hem and to finish 8 1/2" long from shoulder seams.

123

BUTTONS:

First grade 22-ligne melamine. STITCHING: Single needle stitching throughout the shirt. All topstitched 1/4" off the edge. Sleeve inserting and side close felling safety stitched.

THREAD: All sewing threads to be fast color polyester core polyester wrap to match. MILITARY CREASES: 5 Lintrak creases or equivalent silicone military creases on all shirts  Front: 1 crease on each front to be centered vertically through pocket and flap Spacing for three military creases across shirt back to be proportionate to the size of the shirt. INTERLININGS:

Collar interlined with #285 Stabilized Mello-Press. Pocket flaps and top center to be interlined with #550 Stabilized Mello-Press. CONSTRUCTION: Collars, flaps and epaulets are made by the conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out, and finally topstitched. SIZES:

30R-50R (Even Sizes)

34RL-50RL (Even Sizes)

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

68 POLYESTER SILVER TAN TROUSER, MEN’S Flying Cross by Fechheimer 918

(AIRPORT BUREAU)

124

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC:

100% DACRON POLYESTER 12-12 ½ OZ./LINEAR YARD (60" WIDTH)

ELASTIQUE WEAVE COLOR: SILVER TAN TENSILE STRENGTH: 240 LBS WARP 212 LBS FILLING FABRIC SHALL INCORPORATE A WASHABLE AND DRY CLEANABLE SOIL RELEASE FINISH FINISH:

Wickable Soil Release CARE:

Home wash CLOSURE:

Crush proof hook and eye, solid brass ratcheting zipper, French fly tab. POCKET:

Straight side front pockets, double welt, hip pockets flaps with button through closure. WAISTBAND:

The waistband shall be constructed using the "closed method" and shall measure 2" wide when finished. The waistband curtain is to be made of the same fabric and color as the pocketing material and must be attached to the trouser with a Rocap (or equal) Machine. The waistband must contain ¾" wide BAN-ROL, or other monofilament stabilizer to prevent roll over at the trouser front and have Tru Grip OR SNUGTEX to keep shirts tucked in. The waistband closure shall be accomplished with a crush-proof hook and eye. The hook and eye shall be reinforced with stays made of non-woven fabric that are anchored by the topstitching for the fly facing and curtain. This topstitching must be to the top of the waistband. There is to be topstitching 1/16" below the waistband seam for added strength. BELT LOOPS:

There shall be a minimum of seven belt loops 2" in width of double thickness. Each loop must have a non-woven interlining. All loops (except for the back center loop) must be sewn into the bottom of the waistband ("dropped" belt loops are cause for rejection) and the top of the belt loops shall be caught into the waistband curtain seam with a Rocap Machine. The bottom of the center back loop shall be tacked to the trouser and the top of the loop shall be tacked to the waistband.

125

STITCHING, PRESSING & FINISHING:

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

69 POLYESTER TAN TROUSER, WOMEN’S Flying Cross by Fechheimer 918WT

(AIRPORT BUREAU)

SPECIFICATIONS AND ESSENTIAL FEATURES FABRIC:

100% DACRON POLYESTER 12-12 ½ OZ./LINEAR YARD (60" WIDTH) ELASTIQUE WEAVE COLOR: SILVER TAN TENSILE STRENGTH: 240 LBS WARP 212 LBS FILLING FABRIC SHALL INCORPORATE A WASHABLE AND DRY CLEANABLE SOIL RELEASE FINISH CARE:

Home wash DESIGN:

Slack shall be manufactured from a women's uniform slack pattern. The slack styling shall incorporate a plain front and straight leg bottoms. The slack will have two straight side pockets, two hip pockets with flaps. POCKET:

The two side pockets will have a minimum opening of 6 ¼" and a minimum depth of 5 ¾" measured from the bottom of the opening. Side pockets to have triangle bartacks at the top and bottom of pocket openings. Pockets shall be constructed using the stitch, turn, and top stitch method. Pocket facings shall be made of the basic fabric and shall measure a minimum of 1 ¾" in width.

126

The two hip pockets shall have a minimum opening of 5 ½" and a minimum depth of 5 ¾" measured from the bottom of the pocket opening. Hip pockets shall be constructed using the double welt method on a REECE PW Machine and the welts shall be finished in such a manner that there is no topstitching (topstitched hip pockets shall be cause for rejection). The corners of the hip pocket openings shall have triangle bartacks for reinforcing strength. Both hip pockets shall have pocket flaps with a button hole. Flaps to measure 2 ¼" in center and 1 ¾" at each end. Flap edges shall be straight, not scalloped. The watch pocket shall be located on the right front at the waistband. This pocket shall have a minimum opening and depth of 2 ¾". The front of the pocket shall be made of pocketing fabric and the back of the pocket shall be made of basic fabric and the two pieces are securely stitched together. Each corner of the pocket opening shall have firm straight bartacks. WAISTBAND:

The waistband shall be constructed using the "closed method" and shall measure 2" wide when finished. The waistband curtain is to be made of the same fabric and color as the pocketing material and must be attached to the trouser with a Rocap (or equal) Machine. The waistband must contain ¾" wide BAN-ROL to prevent roll over and have Tru Grip to keep shirts tucked in. The waistband closure shall be accomplished with a crush-proof hook and eye. The hook and eye shall be reinforced with stays made of non-woven fabric that are anchored by the topstitching for the fly facing and curtain. This topstitching must be to the top of the waistband. There is to be topstitching 1/16" below the waistband seam for added strength.

BELT LOOPS:

There shall be a minimum of seven belt loops 2" Each loop must have a non-woven interlining. All loops (except for the back center loop) must be sewn into the bottom of the waistband ("dropped" belt loops are cause for rejection) and the top of the belt loops shall be caught into the waistband curtain seam with a Rocap (or equal) Machine. The bottom of the center back loop shall be tacked to the trouser and the top of the loop shall be tacked to the waistband.

STITCHING, PRESSING & FINISHING:

Trouser must be stitched with matching thread and all stitching to show must be 10-11 stitches per inch. Trouser must be neatly pressed on Hothead Presses and properly shaped. Outseams and inseams must be pressed open. Trouser must be cleaned and finished to eliminate loose threads. SIZE:

Women’s: 4-24

127

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

70 BICYCLE HELMET Giro Bishop or Revel

SPECIFICATIONS AND ESSENTIAL FEATURES

BICYCLE HELMET

Giro Bishop Bicycle Helmet

Bishop SKU: SKU: GRB21573237L

COLOR

Black/Charcoal

FEATURES:

Full coverage shell; Snap fit visor with reinforced anchor points

Construction

In-Mold polycarbonate shell with EPS liner

Fit System

Acu Dial™

Ventilation

128

22 vents

Reflective Rear Decal For Added Visibility

SIZES

Universal Adult and Extra Large

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

71 SUNGLASSES BS BODY SPECS EW 957 BLK/SMK

Missing photo

SPECIFICATIONS AND ESSENTIAL FEATURES

BS Body Specs EW 957 sunglasses

Pistol PKGBLKPAN

COLOR

Black/Smoke

129

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Duty Belt- Synthetic Leather Bianchi (Accumold Elite) NP160 (galls #) 72

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

Bianchi Accumold Elite 2 1/4" Duty Belt

 4-part laminate construction  Tri-Release shatter resistant, polymer buckle features 3-point release for added security  Duraskin exterior with loop lining for use with Bianchi belt liner  Closed-cell foam for support

Sizes: S (28-34), M (34-40), L (40-46), XL (46-52) Belts are 2" oversized to accommodate liner belt and padding

130

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Bianchi International NP826 (Galls #) 73 Liner Belt- Nylon

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

 Combines with duty belt to create keeper-less system.  Works with Bianchi Nylon (Tac/Specs/Hondas) and Accumold Elite (Lightweight Issue) duty belts.  Hook and Loop (Velcro) exterior for mating with duty belt.  Worn in place of issued leather pants belt.

131

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Bianchi International NP164 BLK STG 74 Double Magazine Pouch- Nylon (Galls #)

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

 Ballistic weave nylon  Fits double stack magazines

132

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Bianchi International NP169 (Galls #) 75 OC Case Mk3- Nylon

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

 AccuMold trilaminate construction with ballistic weave exterior.  Full flap with exclusive Roll Top lid helps secure canister  Fits belts up to 2.25”

133

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Bianchi International RC-031BLK (Galls #) 76 Radio Case- Nylon

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

 Fits common radio sizes  Elastic tie down  Swivel mount

134

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Bianchi International NP166 (Galls #) 77 Single Handcuff Case- Nylon

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

 Covered cuff case.  AccuMold trilaminate construction with ballistic weave exterior.  Dual web belt loop design accommodates both 2" and 2.25" belt widths.  Holds standard or linked handcuffs.

135

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Baton Ring- Nylon Bianchi International NP175 (Galls #) 78 Mfg #:SH474

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

 Nylon  Ballistic Weave  Fits belts up to 2.25”  PR24 ring, but works with issued SFPD sticks.

136

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Bianchi International NP171 79 Key Keeper- Nylon (Galls #)

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

 Nylon  Snap closure

137

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Bianchi International NP168 BLK (Galls #) 80 Keepers- Nylon

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

 Fits belts up to 2.25”

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Maxpedition 81 Maxpedition Single Sheath pouch for flashlight (SPECS & TACT)

SPECIFICATIONS AND ESSENTIAL FEATURES

138

PRODUCT DESCRIPTION:

 Magazine/Knife/Tool Sheath.  Overall size: 2"(L) x 1.5"(W) x 6"(H)  Adj. lid; elastic retention.  Belt: 2" Vert. or Horz.  Attach: Velcro strips on the back

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

ESS MFG# 740-0131 82 Fan Goggles- Specs

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

 Full eye protection from debris/impact  Anti-fog fan  Runs on single AA battery  2.8mm thick: MIL-PRF-32432, ANSI Z87.1-2010, CE EN 166 and U.S. Federal OSHA compliant  100% UVA/UVB protection

139

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

GL406 (Galls) Hatch “SOG Operator” Tactical Gauntlet Gloves- Specs 83 MFG#:216 OACRLZ

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

KEVLAR construction provides cut resistance, heat, and flash protection

SOG-700 contains 85% Nomex and 15% Kevlar blend

Will not support flame or combust up to 800 F, (427 C)

Elasticized wrist keeps the Operator taut, while the elasticized gauntlet keeps out foreign objects and prevents snagging.

140

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

84 PUBLIC SAFETY VEST SPIEWAK S912P

SPECIFICATIONS AND ESSENTIAL FEATURES COLOR:

HV Yellow/Black 062 SIZE:

Med (XS-M), 2X (L-2XL), 4X (3XL -4XL), 6X (5XL-6XL)

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

85 202L4 Duty Belt W/Dee Rings Lined Stitched 4 Rows Tex Shoemaker & Sons 201L

SPECIFICATIONS AND ESSENTIAL FEATURES

141

STYLE:

Duty belt is 2 1/4" wide, fully lined with Slide-on or Sewn-on D-Rings and stitched 4 rows

COLOR:

Black basketweave

BELT SIZE:

Even sizes 28-64

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

86 Women’s Duty Belt Tex Shoemaker & Sons Inc. 201LC Duty Belt Curved "Fully Lined"

SPECIFICATIONS AND ESSENTIAL FEATURES STYLE:  Sally Browne 2 ¼” wide  100% cowhide  Black basket weave  Fully lined  Saddle stitched  brass buckle

142

COLOR: Black

BELT SIZE: 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48, 50, 52, 54, 56, 60, 62, 64

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

87 Dress Belt 1 1/2" Tex Shoemaker & Sons Inc. Model # 254

SPECIFICATIONS AND ESSENTIAL FEATURES STYLE:  1 ½” Trouser Belt  100% cowhide  Basket weave  Brass buckle COLOR: Black

BELT SIZE: 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48, 50, 52, 54, 56, 60, 62, 64

143

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

88 Handcuff Pouch Tex Shoemaker & Sons Inc. 204 Cuff Case Top Flap, Hidden Snap, for Hinged Cuffs

SPECIFICATIONS AND ESSENTIAL FEATURES STYLE:  Slide on style. Belt slot for 2 ¼” Sam Browne Duty Belt  Basket weave  Hidden Snap  Fits standard sized hinged handcuffs

COLOR: Black

SIZE: N/A

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

89 OC Spray Holder Tex Shoemaker & Sons Inc. 92AM4 for Mark 4Standard, Top Flap Hidden Snap

144

SPECIFICATIONS AND ESSENTIAL FEATURES STYLE:  Mace holder with a covered top carries a 1 1/2" mark 4 tear gas canister with an open bottom for easy access.  Slide on style for a 2 ¼” Sam Browne Duty Belt  Basket weave  Hidden snap

COLOR: Black

SIZE: N/A

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

90 Silent Key Holder Tex Shoemaker & Sons Inc. 88SK

SPECIFICATIONS AND ESSENTIAL FEATURES STYLE:  Basket weave  Black Snap  Silent key holder with velcro closure Slide on style for a 2 ¼” Sam Browne

145

COLOR: Black

SIZE: N/A

DESCRIPTION MANUFACTURER MODEL # IMAGE ITEM #

91 Chain Link Handcuff Peerless Handcuff Company # 701C Chain Link Handcuff

SPECIFICATIONS AND ESSENTIAL FEATURES STYLE: The classic design is new and improved. The Model 701C features an improved internal lock mechanism for increased tamper resistance, smoother ratcheting action and greater durability. The 701C incorporates spun rivet construction, push pin double lock capability and black oxide finish. Two keys supplied. The Model 701C is made to meet National Institute of Justice Standard 0307.01 and comes with a lifetime warranty for manufacture defects. Made in USA.

 Weight: 10 oz. / 283 gms  Minimum inside perimeter: 5.9 in. / 150 mm  Material/Finish: Carbon Steel / Black Oxide  Maximum inside perimeter: 8.3 in / 211 mm  Minimum opening: 2.0 in / 51 mm  Maximum overall length: 9.3 in / 236 mm

COLOR: Black Oxide Finish

146

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

92 Double Snap 3/4" wide keepers AKER A531-BW Fits Duty Belts up to 2 1/4". 2248 Main Street, Suite 6 Chula Vista, CA 91911-1363 619-423-5182

SPECIFICATIONS AND ESSENTIAL FEATURES Description The Keeper Strap Shall Be Made of Full-Grain Cowhide Not Less Than 8 oz. In Thickness, Designed For Use with the 2.25” Sam Browne Belt. The Keeper Shall Have Two (2) Solid Brass Snap Fasteners. The Keeper Strap Shall Be 8” in Length and .75” in Width. Leather: 8-9 oz. Full Grain Vegetable Tanned Cowhide Hardware: Solid Brass Snaps Stitching: n/a Dye: Water Based Black Dye Glue: n/a Size: n/a Finish: X511 Basket Weave Design Country of Origin: Made in the USA - California DETAILS OF ASSEMBLY: Edges: All Edges Shall Be Edged With A Hand Tool (#133) To Provide Rounded edges Gluing: n/a Dyeing: Shall be dip dyed in water based black dye Sewing: n/a Burnishing: All edges shall be burnished to a smooth finish with a deburring wheel Sanding: n/a Stamping: Shall have “SFPD” stamped with .25” letters on backside Color: Black

147

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

93 Baton Ring With Snap SAFARILAND 67S-4PBL

SPECIFICATIONS AND ESSENTIAL FEATURES STYLE:  Basket weave  Brass ring  Brass snap COLOR: Black SIZE: N/A

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

94 Dyna-thin unlined leather glove with short cuff Damascus Gear Part# D20P

SPECIFICATIONS AND ESSENTIAL FEATURES

148

SPECIFICATIONS:

 Smooth premium quality aniline finished cowhide for exceptional sensitivity and dexterity  Gathered wrist  Unlined

Size range: Men’s XSM to XXLG

COLOR: Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

# 113126 Baton # 199060 95 26” Straight Wood Baton AETCO Rubber Baton Taper Grommet

SPECIFICATIONS AND ESSENTIAL FEATURES STYLE:

26” Straight Baton – Plain  Straight Stick Wooden Batons Features:  Made of Solid Ash  Rounded ends

Rubber Baton Taper Grommet

149

 The taper grommet is a baton stop that supports the baton in a belt carry ring. The taper grommet fits all 1.25-in diameter batons.

COLOR: Black

SIZE: N/A

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

# 113136 # 199060 96 36” Wooden Riot Baton AETCO Rubber Baton Taper Grommet

SPECIFICATIONS AND ESSENTIAL FEATURES

150

STYLE:

36” Wooden Riot Baton – Plain  Straight Riot Baton, 36”  Made of Solid Ash  Rounded ends

Rubber Baton Taper Grommet The taper grommet is a baton stop that supports the baton in a belt carry ring. The taper grommet fits all 1.25-in diameter batons. COLOR: Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

97 26" RCB Nickel Collapsible Baton Peacekeeper Products International 926N

SPECIFICATIONS AND ESSENTIAL FEATURES COLOR:  Black Handle Nickel Finish

SIZE: Also available in 24”, 29”

151

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

98 Secure Lock Rotational Holster (Large) Peacekeeper Products International 940-SLBW

SPECIFICATIONS AND ESSENTIAL FEATURES STYLE:  Secure Lock Rotational Holster (Large) for 24,” 26,” and 29” RCB Batons Basket weave finish COLOR: Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

99 Whistle VANGUARD 9700500

SPECIFICATIONS AND ESSENTIAL FEATURES

152

SPECIFICATION:  Whistle: Plastic Weight: 0.25 oz. COLOR: Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Bianchi Accumold (Safariland) 7907 100 OC Holder Mk 3

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

 Basket Weave  Designed for new Sabre Crossfire Mk3 OC  Brass snap/Hidden snap  Designed for use with 2.25” Sam Browne belt.

153

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Sabre 52CFT10 101 Sabre Red OC

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

 Uses time tested SABRE Red formula; 10% OC, 1.33% capsaicinoid content  Fires 10 one-sec bursts  Electronic immobilization device compatible  Non-flammable  4-year shelf life warranty  4-1/2"H x 1-1/2"D  1.8 oz

154

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Don Hume RS270 BLK (Galls #) 102 RIPP Hobble MFG#: A093300X

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

 Allows control of combative kicking subject after handcuffing.  Prevents further kicks by restraining legs.  Permanently attached alligator clip, brass snap ring.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Sirchie Item # LE893/Mfg# 103 Ink pad PMP100

SPECIFICATIONS AND ESSENTIAL FEATURES

155

PRODUCT DESCRIPTION:

 2” round  Pad inside polypropylene case with hinge  Stain free ink  5/8"W x 2"D

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Aker 104 Citation book Z581-PB

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

 Black leather  2 clips for holding pads 5”x10”

156

105 BICYCLE HELMET NUTCASE Gen 3

Missing photo

SPECIFICATIONS AND ESSENTIAL FEATURES

Certified by both the CPSC for cycling and ASTM F1492 for skating standards Durable ABS shell Protective EPS inner foam lining Magnetic buckle means no pinching! Front, top & back venting Crumple zones in external EPSto help disperse energy in the event of a crash Adjustable/Removable spin dial gives a snug & comfortable fit shades you from sun and rain Deluxe soft chin pad for extra comfort An extra set of foam pads to give you the perfect fit Increased 360 degree reflectivity by including straps and spin dial Improved ventilation by adding air channels in EPS

COLOR

Black

SIZES

Small (52cm-56cm)/Medium (56cm-60cm)/Large (60-64cm)

157

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

106 LED Flashlight SureFire SureFire G2X

***SPECIAL NOTES*** SPECIFICATIONS AND ESSENTIAL FEATURES SPECIFICATIONS:

 320 lumens  2.5 hours run time or 45 hours on low  Momentary/constant “on” options  Lockout tailcap  Nitrolon polymer body  Weatherproof  Uses two 123A lithium batteries (included)  Limited lifetime warranty

5.2”L, 4.4 oz COLOR: Black

158

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

107 Flashlight holder Surefire V70 Polymer speed holster (Galls NP543)

SPECIFICATIONS AND ESSENTIAL FEATURES SPECIFICATIONS:  Must be compatible with flashlight being bid Must fit belts up to 2.25” wide COLOR:  Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Propper Propper style # F5634 108 1.5” Cobra liner belt

SPECIFICATIONS AND ESSENTIAL FEATURES

159

PRODUCT DESCRIPTION:

 Hook & Loop adjustable fit  Worn in place of issued leather pants belt.  1.5” double layer nylon webbing

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

ARCTERYX KNEE CAP 109 KNEE PADS BLACK (TAC & Specs) ARC.510

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

Technical Features

• Lightweight

• Low profile

• Durable

Construction

• Low-profile camlocks for quick adjustability

• Two robust elasic straps

160

Patterning

• Anatomical shaping for fit and comfort

• Articulated patterning for unrestricted mobility

Materials

• EV®50 foam

• Kydex®

• Surface clean only.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

ALTA FLEX ELBOW PADS 110 ELBOW PADS Black (TAC & Specs) Alt.501

SPECIFICATIONS AND ESSENTIAL FEATURES

161

PRODUCT DESCRIPTION:

• Strong durable elbow pad design • Soft rubber cap is skid-resistant and provides protection and flexibility • Cordura® Nylon cover • Compression recovery 1/2" Neoprene foam padding provides firm, consistent support without bottoming out • Finished brushed tricot liner wicks away moisture and keeps out dirt and debris • Secured with 4 brass grommets • Two elastic straps with AltaGrip™ hook & loop Fastening System • Finished brushed tricot liner wicks away moisture and keeps out dirt and debris • Adjustable to fit most sizes • Black in color

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

111 203L Sam Browne Dee ring duty belt 202 Duty belt with Tex Shoemaker Dee rings

SPECIFICATIONS AND ESSENTIAL FEATURES

Fully lined Integrates with Sam Browne belt

162

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

112 203L Sam Browne shoulder strap 203 Shoulder strap

Tex Shoemaker & Sons

SPECIFICATIONS AND ESSENTIAL FEATURES

STYLE:

Fully lined for a Sam Browne belt

COLOR:

Black basketweave

BELT SIZE:

Measure from D ring to D ring over the shoulder

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

113 906 Riot Duty helmet Premier Crown Galls # TE023

163

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

 Meets or exceeds NIJ 0104.02 standard for riot helmets  Detachable face shield with liquid seal protects the user’s eyes  Polycarbonate alloy outershell with an anti-reflective dull finish  Semi-resilient polystyrene foam liner

SIZES:

Small, X Large, Jumbo

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

114 Model MJ6214 T1 Mustang Survival Flotation jacket w/ reflective tape

SPECIFICATIONS AND ESSENTIAL FEATURES

164

PRODUCT DESCRIPTION:  USCG Type: Type III  Buoyancy: 15.5lb.  Shell Fabric: 210 Denier nylon  Lining Fabric: Nylon  Insulation Material: AirSoft™ foam  Cuffs: Knit Collar: Storm collar  Closure Type: Zipper  Pockets: Two hand pockets, two cargo pockets, interior and shoulder pocket

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Galls Neoprene gloves Galls GL385

115

SPECIFICATIONS AND ESSENTIAL FEATURES

165

PRODUCT DESCRIPTION:

 Non-slip synthetic leather fingertips and palms for better gripping  Neoprene fabric on back of hand for flexibility  Water-resistant

116 BICYCLE GLOVES Fox Reflex Gel Short Finger

SPECIFICATIONS AND ESSENTIAL FEATURES

BICYCLE GLOVES

Fox Reflex Gel Short Finger bicycle gloves

COLOR

Black

166

FEATURES:

 Lightweight flexible top hand  Gel palm inserts  Double layer Clarino® palm  Absorbent micro-suede thumb  Low profile wrist tab closure

SIZES

Small, Medium, Large, XL, and XXL

117 BICYCLE GLOVES Fox Reflex Gel Long Finger

SPECIFICATIONS AND ESSENTIAL FEATURES

BICYCLE GLOVES

Fox Reflex Gel Long Finger bicycle gloves

COLOR

Black

167

FEATURES:

 Lightweight flexible top hand  Gel palm inserts  Double layer Clarino® palm  Silicone grip fingertip  Absorbent micro-suede thumb  Low profile wrist tab closure

SIZES

Small, Medium, Large, XL, and XXL

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

118 Crossed sabre pins N/A

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

Black

168

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

119 Crossed sabre pins N/A

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

Gold

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Horse head lapel pins for dress coat

120

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

169

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

121 Grip Flex Military Braided Style Shoulder Cord Galls Item #UN004 YEL

SPECIFICATIONS AND ESSENTIAL FEATURES Features

 Single color

COLOR:

Gold

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

122 Stratton Hats Felt Campaign Hat F-40 F40

SPECIFICATIONS AND ESSENTIAL FEATURES

170

Features

 Wool Felt  Extra Stiff Brim  Single Vent Eyelet front and back  Chin Strap attached

COLOR:

Black/Navy SIZE:

6 ½ to 7 7/8. Varying oval sizes.

DESCRIPTION MANUFACTURER MODEL # IMAGE ITEM #

123 Stratton Hats Campaign Hat Cords

SPECIFICATIONS AND ESSENTIAL FEATURES Features

 Gold laminate  Gold Acorns

COLOR:

Solid Gold. Gold/Black

171

SIZE:

Fixed.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

124

N/A Hat Emblem Irvine & Jachens, Inc. SFPD Hat Badge 6700 Mission Street Model #734 Daly City, California 94014

(650) 755-4715

SPECIFICATIONS AND ESSENTIAL FEATURES

 City and County of San Francisco Seal  Constructed of molded solid brass w/3/8” long screw post on back and ¼” sharpened point at the top

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

125 Galls Dress Gloves GL683

172

SPECIFICATIONS AND ESSENTIAL FEATURES Features

 Full Fashion Snap Wrists  White heavyweight cotton gloves  Sure-Grip PVC Dots on palm  Sizes: S, M, L, and XL

COLOR:

White SIZE:

Small/ Medium/ Large/ XL

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

126

N/A Lapel Insignia gold color, reads “COLOR GUARD” Paradestore.com

SPECIFICATIONS AND ESSENTIAL FEATURES

173

 Clutchback pin  1 1/8” width by 1 1/2” height

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Blackhawk 127 FR Balaclava- Specs

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

 7.4 oz Nomex, Fire Resistant. Heavyweight.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

128 TRU SPEC HW202

EVOC

TRU SPEC Boonie Hat

SPECIFICATIONS AND ESSENTIAL FEATURES

174

Features

 65% Polyester/ 35% Cotton Ripstop  Mil-spec  Brass screen vents  Adjustable chin strap Imported COLOR:

Coyote Tan

SIZE:

S (7”), M (7-1/4”), L (7-1/2”), XL (7-3/4”)

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Galls NT017 (Galls #) 129 Nameplate

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

 2 ½” length. 5/8” height.  Pin back  Gold

175

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

130 Shoulder Emblem – Full Color National Emblem, Inc. 8050-01

“SAN FRANCISCO POLICE”

SPECIFICATIONS AND ESSENTIAL FEATURES

176

National Emblem, Inc. Design # 8050-01

Description Shoulder Emblem

Accurate Size 4x5”

Shape Shield

FUFU Thread Colors / Type  PF 367 Med / Light Royal  PF 548 Medium Gold  PF 7125 Desert Orange  PF 7361 Dark Brown  PF 900 Black

Twill Colors / Type  Solid Stitch

Total Colors 8

Embroidery 100%

Border  PF 900 Black (Marrow Border)

Backing Thermo-Plastic

177

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

131 Shoulder Emblem – Subdued National Emblem, Inc. 85080-02

“SAN FRANCISCO POLICE”

SPECIFICATIONS AND ESSENTIAL FEATURES

178

National Emblem, Inc. Design # 85080-02

Description Subdued Shoulder Emblem

Accurate Size 4x5”

Shape Shield

FUFU Thread Colors / Type  PF 900 Black  PF 4256 Dark Grey  PF 4253 Grey Twill Colors / Type  E-954 Subdued Twill

Total Colors 2

Embroidery 75%

Border PF 900 Black (Marrow Border)

Backing Thermo-Plastic

179

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

132 Shoulder Emblem – Subdued National Emblem, Inc. 108090

“SAN FRANCISCO POLICE ACADEMY”

SPECIFICATIONS AND ESSENTIAL FEATURES

180

National Emblem, Inc. Design # 108090

Description Subdued Shoulder Emblem

Accurate Size 4x5”

Shape Shield

FUFU Thread Colors / Type  PF 367 Royal  PF 544 Light Gold  Pf 736 Light Brown  PF 738 Brown  PF 700 Red  PF 900 Black Twill Colors / Type  ?

Total Colors 6

Embroidery 100%

Border PF 900 Black (Marrow Border)

Backing Thermo-Plastic

181

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

133 Reduced Cap Patch – Full Color National Emblem, Inc. 97118

“SAN FRANCISCO POLICE”

SPECIFICATIONS AND ESSENTIAL FEATURES

182

National Emblem, Inc. Design # 97118

Description Shoulder Emblem

Accurate Size 2 ¾ X 3 ¼

Shape Reduced Shield

FUFU Thread Colors / Type  PF 367 Med / Light Royal  PF 548 Medium Gold  PF 7125 Desert Orange  PF 7361 Dark Brown  PF 900 Black

Twill Colors / Type  Solid Stitch

Total Colors 8

Embroidery 100%

Border  PF 900 Black (Marrow Border)

Backing Thermo-Plastic

183

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

134 Reduced Cap Patch – Full Color National Emblem, Inc. 108089

“SAN FRANCISCO POLICE ACADEMY”

SPECIFICATIONS AND ESSENTIAL FEATURES

184

National Emblem, Inc. Design # 108089

Description Shoulder Emblem

Accurate Size 2 11/16” X 3 3/8”

Shape Reduced Shield

FUFU Thread Colors / Type  PF 367 Royal  PF 544 Light Gold  PF 736 Light Brown  PF 738 Brown  PF 700 Red  PF 900 Black

Twill Colors / Type  Solid Stitch

Total Colors 8

Embroidery 100%

Border  PF 900 Black (Marrow Border)

Backing Thermo-Plastic

185

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

135 Star Badge Emblem (Full Color) National Emblem, Inc. N/A

“SAN FRANCISCO POLICE”

SPECIFICATIONS AND ESSENTIAL FEATURES

186

National Emblem, Inc. Design # N/A

Description Star Badge Emblem (Full Color)

Accurate Size 3x3”

Shape 7 Point Star

FUFU Thread Colors / Type  Silver  900 Black (Rayon)

Twill Colors / Type  Solid Stitch

Total Colors 2

Embroidery 100%

Border Stitched FUFU Silver

Backing Thermo-Plastic

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

136 Star Emblem – Gold National Emblem, Inc. N/A No Photo

“SAN FRANCISCO POLICE”

SPECIFICATIONS AND ESSENTIAL FEATURES

187

National Emblem, Inc. Design # N/A

Description Star Badge Emblem (Gold)

Accurate Size 3x3”

Shape 7 Point Star

FUFU Thread Colors / Type  ??? (GOLD)  900 Black (Rayon) Twill Colors / Type  Solid Stitch

Total Colors 2

Embroidery 100%

Border Stitched FUFU GOLD?????

Backing Thermo-Plastic

188

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

137 Star Emblem – Subdued National Emblem, Inc. 67137

“SAN FRANCISCO POLICE”

SPECIFICATIONS AND ESSENTIAL FEATURES

189

National Emblem, Inc. Design # 67137

Description Star Emblem - Subdued

Accurate Size 3x3”

Shape 7 Point Star

FUFU Thread Colors / Type  900 Black (Rayon)

Twill Colors / Type  E954 Subdued Twill OR JM 208 Olive Green??? Total Colors 1

Embroidery 35 %

Border FUFU Black 900 Stitched

Backing Thermo-Plastic

190

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

138 Sergeant Chevrons (Full Color) National Emblem, Inc. 109677

SPECIFICATIONS AND ESSENTIAL FEATURES

191

National Emblem, Inc. Design # 109677

Description Sergeant Chevrons (Full Color)

Accurate Size 3”X 3-¾”

Shape Irregular

FUFU Thread Colors / Type  ROYAL FF367  GOLD PF544  BLACK PF900 Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 75%

Border Stitched FUFU Black 900

Backing Thermo-Plastic

192

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

139 Sergeant Chevrons (Subdued) National Emblem, Inc. 108083

SPECIFICATIONS AND ESSENTIAL FEATURES

National Emblem, Inc. Design # 108083

Description Sergeant Chevrons (Full Color)

Accurate Size 3”X 3-¾”

Shape Irregular

FUFU Thread Colors / Type  ??

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 75%

Border Stitched FUFU Black 900

Backing Thermo-Plastic

193

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

140 Lieutenant Bar National Emblem, Inc. 111476-01

SHIRT SIZE - GOLD

SPECIFICATIONS AND ESSENTIAL FEATURES

194

National Emblem, Inc. Design # 111476-01

Lieutenant Bar

Description

SHIRT SIZE - GOLD

Accurate Size ¾ ”X1-¼”

Shape Square

FUFU Thread Colors / Type  Gold (Rayon) - FF546 Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU

Border BLACK FF900

(Hot Knife Edge)

Backing Thermo-Plastic

195

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

141 Lieutenant Bar National Emblem, Inc. 111476-02

SHIRT SIZE - SUBDUED

SPECIFICATIONS AND ESSENTIAL FEATURES

196

National Emblem, Inc. Design # 111476-02

Lieutenant Bar

Description

SHIRT SIZE – Subdued

Accurate Size ¾ ”X1-¼”

Shape Square

FUFU Thread Colors / Type  238 Green (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900 / POSSIBLE CHANGE TO BE MATCHED WITH BDU Border

(Hot Knife Edge)

Backing Thermo-Plastic

197

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

142 Lieutenant Bar National Emblem, Inc. 108080

JACKET SIZE - GOLD

SPECIFICATIONS AND ESSENTIAL FEATURES

198

National Emblem, Inc. Design # 108080

Lieutenant Bar

Description

JACKET SIZE - GOLD

Accurate Size 1-¾”X1-¾”

Shape Square

FUFU Thread Colors / Type  546 Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU

Border BLACK FF900

(Hot Knife Edge)

Backing Thermo-Plastic

199

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

143 Lieutenant Bar National Emblem, Inc. 108081

JACKET SIZE - SUBDUED

SPECIFICATIONS AND ESSENTIAL FEATURES

200

National Emblem, Inc. Design # 108081

Lieutenant Bar

Description

JACKET SIZE - SUBDUED

Accurate Size 1-¾”X1-¾”

Shape Square

FUFU Thread Colors / Type  238 Green (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900 / POSSIBLE CHANGE TO BE MATCHED WITH BDU Border

(Hot Knife Edge)

Backing Thermo-Plastic

201

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

144 Captain Bar National Emblem, Inc. 108074

SHIRT SIZE - GOLD

SPECIFICATIONS AND ESSENTIAL FEATURES

202

National Emblem, Inc. Design # 108074

Captain Bar

Description

SHIRT SIZE - GOLD

Accurate Size 1-¼”X1-¼”

Shape Square

FUFU Thread Colors / Type  Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU

Border BLACK FF900

(Hot Knife Edge)

Backing Thermo-Plastic

203

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

145 Captain Bar National Emblem, Inc. 108075

SHIRT SIZE - SUBDUED

SPECIFICATIONS AND ESSENTIAL FEATURES

204

National Emblem, Inc. Design # 108075

Captain Bar

Description

SHIRT SIZE - SUBDUED

Accurate Size 1-¼”X1-¼”

Shape Square

FUFU Thread Colors / Type  238 Green (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900 / POSSIBLE CHANGE TO BE MATCHED WITH BDU Border

(Hot Knife Edge)

Backing Thermo-Plastic

205

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

146 Captain Bar National Emblem, Inc. 108076

JACKET SIZE - GOLD

SPECIFICATIONS AND ESSENTIAL FEATURES

206

National Emblem, Inc. Design # 108076

Captain Bar

Description

JACKET SIZE - GOLD

Accurate Size 1-5/8”X1-5/8”

Shape Square

FUFU Thread Colors / Type  546 Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU

Border BLACK FF900

(Hot Knife Edge)

Backing Thermo-Plastic

207

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

147 Captain Bar National Emblem, Inc. 108077

JACKET SIZE - SUBDUED

SPECIFICATIONS AND ESSENTIAL FEATURES

208

National Emblem, Inc. Design # 108077

Captain Bar

Description

JACKET SIZE - SUBDUED

Accurate Size 1-5/8”X1-5/8”

Shape Square

FUFU Thread Colors / Type  238 Green (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900/ POSSIBLE CHANGE TO BE MATCHED WITH BDU Border

(Hot Knife Edge)

Backing Thermo-Plastic

209

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

148 Commander Star National Emblem, Inc. N/A No Photo

SHIRT SIZE - GOLD SPECIFICATIONS AND ESSENTIAL FEATURES

210

National Emblem, Inc. Design # N/A

Commander Star

Description

SHIRT SIZE - GOLD

Accurate Size 1” x 2”

Shape Rectangle

FUFU Thread Colors / Type  546 Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

211

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

149 Commander Star National Emblem, Inc. N/A No Photo

SHIRT SIZE – SUBDUED SPECIFICATIONS AND ESSENTIAL FEATURES

212

National Emblem, Inc. Design # N/A

Commander Star

Description

SHIRT SIZE – SUBDUED

Accurate Size 1” X 2”

Shape Rectangle

FUFU Thread Colors / Type  238 Green (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

213

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

150 Commander Star National Emblem, Inc. N/A No photo

JACKET SIZE - GOLD SPECIFICATIONS AND ESSENTIAL FEATURES

214

National Emblem, Inc. Design # N/A

Commander Star

Description

JACKET SIZE - GOLD

Accurate Size 1” X 2”

Shape Rectangle

FUFU Thread Colors / Type  546 Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

215

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

151 Commander Star National Emblem, Inc. N/A No photo

Jacket Size - Subdued SPECIFICATIONS AND ESSENTIAL FEATURES

216

National Emblem, Inc. Design # N/A

Commander Star

Description

Jacket Size - Subdued

Accurate Size 1” X 2”

Shape Rectangle

FUFU Thread Colors / Type  238 Green (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

217

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

152 Chief Deputy Star National Emblem, Inc. 111576-1

SHIRT SIZE - GOLD SPECIFICATIONS AND ESSENTIAL FEATURES

218

National Emblem, Inc. Design # 111576-1

Chief Deputy Star

Description

SHIRT SIZE - GOLD

Accurate Size ¾” X 1 ½”

Shape Rectangle

FUFU Thread Colors / Type  546 Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

219

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

153 Chief Deputy Star National Emblem, Inc. 111576-2

SHIRT SIZE – SUBDUED SPECIFICATIONS AND ESSENTIAL FEATURES

220

National Emblem, Inc. Design # 111576-2

Chief Deputy Star

Description

SHIRT SIZE – SUBDUED

Accurate Size ¾” X 1 ½”

Shape Rectangle

FUFU Thread Colors / Type  238 Green (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

221

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

154 Chief Deputy Star National Emblem, Inc. 111576-01

JACKET SIZE - GOLD

SPECIFICATIONS AND ESSENTIAL FEATURES

222

National Emblem, Inc. Design # 111615-01

Chief Deputy Star

Description

JACKET SIZE - GOLD

Accurate Size 1” X 2”

Shape Rectangle

FUFU Thread Colors / Type  546 Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

223

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

155 Chief Deputy Star National Emblem, Inc. 111576-02

Jacket Size - Subdued

SPECIFICATIONS AND ESSENTIAL FEATURES

224

National Emblem, Inc. Design # 111615-02

Chief Deputy Star

Description

Jacket Size - Subdued

Accurate Size 1” X 2”

Shape Rectangle

FUFU Thread Colors / Type  238 Green (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

225

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

156 Chief Stars

National Emblem, Inc. 111618-01 SHIRT SIZE - GOLD

SPECIFICATIONS AND ESSENTIAL FEATURES

226

National Emblem, Inc. Design # 111618-01

Chief Star

Description

SHIRT SIZE - GOLD

Accurate Size ¾ X 2 ½”

Shape Rectangle

FUFU Thread Colors / Type  546 Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 30%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

227

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE Chief Stars 157 National Emblem, Inc. 111618-02 SHIRT SIZE - SUBDUED

SPECIFICATIONS AND ESSENTIAL FEATURES

228

National Emblem, Inc. Design # 111618-02

Chief Star

Description

Shirt Size - Subdued

Accurate Size ¾ X 2 ½”

Shape Rectangle

FUFU Thread Colors / Type  238 Green (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 30%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

229

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

158 Chief Star National Emblem, Inc. 111617-01

JACKET SIZE - GOLD

SPECIFICATIONS AND ESSENTIAL FEATURES

230

National Emblem, Inc. Design # 111617-01

Chief Star

Description

JACKET SIZE - GOLD

Accurate Size 1 X 3 ½

Shape Rectangle

FUFU Thread Colors / Type  546 Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Stitched FUFU Black 900

Border

(Hot Knife Edge)

Backing Thermo-Plastic

231

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

159 Chief Star National Emblem, Inc. 111617-02

JACKET SIZE - SUBDUED

SPECIFICATIONS AND ESSENTIAL FEATURES

232

National Emblem, Inc. Design # 111617-02

Chief Star

Description

JACKET SIZE - SUBDUED

Accurate Size 1 X 3 ½

Shape Rectangle

FUFU Thread Colors / Type  238 Green (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Border Stitched FUFU Black 900

(Hot Knife Edge)

Backing Thermo-Plastic

233

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

160 CSI Back Emblem – SILVER National Emblem, Inc. N/A N/A

SPECIFICATIONS AND ESSENTIAL FEATURES

National Emblem, Inc. Design # N/A

Description CSI Back Emblem – Silver

Accurate Size 4” X 11”

Shape Rectangle With Rounded Corners

FUFU Thread Colors / Type  N/A

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Border Overlocked (??? Silver)

Backing Thermo-Plastic

234

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

161 EVOC Back Emblem – GOLD National Emblem, Inc. N/A No photo

SPECIFICATIONS AND ESSENTIAL FEATURES

National Emblem, Inc. Design # N/A

Description EVOC Back Emblem – Gold

Accurate Size 4” X 11”

Shape Rectangle With Rounded Corners

FUFU Thread Colors / Type  N/A

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Border Overlocked (546 Gold)

Backing Thermo-Plastic

235

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

162 Negotiator Back Emblem – Gold National Emblem, Inc. 110791

SPECIFICATIONS AND ESSENTIAL FEATURES

National Emblem, Inc. Design # 110791

Description Negotiator Back Emblem – Gold

Accurate Size 4” X 11”

Shape Rectangle With Rounded Corners

FUFU Thread Colors / Type  546 Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Border Overlocked (546 Gold)

Backing Thermo-Plastic

236

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

163 POLICE Back Emblem – Black National Emblem, Inc. 703566 n/a with Olive Drab Background

SPECIFICATIONS AND ESSENTIAL FEATURES

National Emblem, Inc. Design # 703566

Description Police Back Emblem – Black

Accurate Size 4” X 11”

Shape Rectangle With Rounded Corners

FUFU Thread Colors / Type  900 Black (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Border Overlocked 900 Black

Backing Thermo-Plastic

237

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

164 POLICE Back Emblem – Gold National Emblem, Inc. 70366

SPECIFICATIONS AND ESSENTIAL FEATURES

National Emblem, Inc. Design # 70366

Description POLICE Back Emblem – Gold

Accurate Size 4” X 11”

Shape Rectangle With Rounded Corners

FUFU Thread Colors / Type  546 Gold (Rayon)

Twill Colors / Type  E936 100% Polyester

Total Colors 1

Embroidery 35%

Border Overlocked (546 Gold)

Backing Thermo-Plastic

238

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

165 Motorwing Patch National Emblem, Inc. N/A No photo

SPECIFICATIONS AND ESSENTIAL FEATURES

National Emblem, Inc. Design # N/A

Description POLICE Motor Wing Patch – white, gold, black

Accurate Size N/A

Shape N/A

FUFU Thread Colors / Type  N/A

Twill Colors / Type  N/A

Total Colors N/A

Embroidery N/A

Border N/A

Backing Thermo-Plastic

239

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

166 SF PSA Supervisor Rocker Patch National Emblem, Inc. N/A N/A

SPECIFICATIONS AND ESSENTIAL FEATURES

National Emblem, Inc. Design # N/A

Description SF PSA Supervisor Rocker Patch

Accurate Size N/A

Shape N/A

FUFU Thread Colors / Type  N/A

Twill Colors / Type  N/A

Total Colors N/A

Embroidery N/A

Border N/A

Backing Thermo-Plastic

240

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

167 SF Police Services Aide Rocker Patch National Emblem, Inc. N/A No photo

SPECIFICATIONS AND ESSENTIAL FEATURES

National Emblem, Inc. Design # N/A

Description SF Police Services Aide Rocker Patch

Accurate Size N/A

Shape N/A

FUFU Thread Colors / Type  N/A

Twill Colors / Type  N/A

Total Colors N/A

Embroidery N/A

Border N/A

Backing Thermo-Plastic

241

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

HERO’S PRIDE 4007G 168 Tie Bar

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

 Gold

242

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

169 Vanguard 7179800

LIEUTENANT 2440 Impala Drive (Single Bar) Carlsbad, CA 92010 (800) 433-1334 Collar Size 3/4” Double-Clutch Backing Gold Plated

TOLERANCES: NONE

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

170 Vanguard

LIEUTENANT 7165200 2440 Impala Drive (Single Bar) Carlsbad, CA 92010 (800) 433-1334

Coat Size

1” Pin Backing

243

Gold Plated

244

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

171 Vanguard 7191200

CAPTAIN 2440 Impala Drive (Double Bar) Carlsbad, CA 92010 (800) 433-1334

Collar Size

3/4” Double-Clutch Backing

Gold Plated

245

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

172 Vanguard

CAPTAIN 7165240

(Double Bar) 2440 Impala Drive Carlsbad, CA 92010 (800) 433-1334 Coat Size

1” Pin Backing

Gold Plated

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

COMMANDER LawPro CB518 GP SM 1STR, 173 (1 Star) CB518 GP LG 1STR LawPro Star Insignia Set

SPECIFICATIONS AND ESSENTIAL FEATURES

246

PRODUCT DESCRIPTION:

 Gold plate  Small ½” Collar size  Large 1” Coat size

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

LawPro CB518 GP SM 2STR, 174 CHIEF DEPUTY CB518 GP LG 2STR (2 Stars)

LawPro Star Insignia Set

SPECIFICATIONS AND ESSENTIAL FEATURES PRODUCT DESCRIPTION:

 Gold plate  Small ½” Collar size  Large 1” Coat size

247

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

LawPro CB518 GP SM 4STR, 175 CHIEF CB518 GP LG 4STR (4 Stars)

LawPro Insignia Set

SPECIFICATIONS AND ESSENTIAL FEATURES

PRODUCT DESCRIPTION:

 Gold plate  Small ½” Collar size  Large 1” Coat size

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

176 WATERBURY BUTTON COMPANY 1-17704-3634-11008 Customized button for Class A Ike Jacket, short and (800) 928-1812 long sleeve uniform shirts, and foul weather jacket to read: “SF Police”

248

SPECIFICATIONS AND ESSENTIAL FEATURES SIZE: 36 Ligne

COLOR: GOLD

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Mechanix wear Galls #GL371 177 PSA Traffic Safety gloves http://www.galls.com/mechanix- wear-safety-original- gloves?PMSRCH=gl371

SPECIFICATIONS AND ESSENTIAL FEATURES Features

 ANSI 107- compliant hi vis material on palm

COLOR:

Hi vis yellow

249

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

SKU# OO9238-06 178 Marine Unit polarized sunglasses Oakley

SPECIFICATIONS AND ESSENTIAL FEATURES SPECIFICATIONS:  Sunglasses shall meet or exceed ANSI Ziu.1+ (impact) standards  Shall be impact resistant and provide at least 98% UVA and 100% UVB protection Lenses should be neutral/Neutral, Slate/Green, or Smoke/Gray in color

Should be worn by personnel to prevent radiation trauma; should provide marine crewmembers protection from the sun’s glare and reflection off the water. Should meet or exceed ANSI Z87.1+ (impact) standards. Shall be impact resistant and provide at least 98% UVA and 100% UVB protection. Lenses should be neutral/neutral, slate/green, or smoke/gray in color. Sunglasses shall conform to the guidelines for military appearance. COLOR:  Black frame

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

179 Marine Unit Wet Weather gloves NRS 25036.02 NRS Tactical Gloves

SPECIFICATIONS AND ESSENTIAL FEATURES

250

SPECIFICATIONS:  Durable enough to withstand the marine environment  Constructed of non-water impregnable material  Full finger, long-finger, or short-finger style Palm and fingers constructed of durable materials.

Should be worn to provide thermal protection in intermediate cold/wet weather; durable enough to withstand the marine environment; constructed of non-water impregnable material; May be full finger, long-finger or short-finger style; Weapon and tool use should be considered. Palm and fingers should be constructed of durable materials. Should provide limited protection from hypothermia when wet inside. COLOR: Black

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

180 Star Badge Emblem (Full Color) National Emblem, Inc. N/A Missing image of gold star patch “SAN FRANCISCO POLICE” Lieutenants and above

SPECIFICATIONS AND ESSENTIAL FEATURES

251

National Emblem, Inc. Design # N/A

Description Star Badge Emblem (Full Color)

Accurate Size 3x3”

Shape 7 Point Star

FUFU Thread Colors / Type  Gold  900 Black (Rayon)

Twill Colors / Type  Solid Stitch

Total Colors 2

Embroidery 100%

Border Stitched FUFU Silver

Backing Thermo-Plastic

252

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Cadet rocker patch National Emblem, Inc. 108064 181

SPECIFICATIONS AND ESSENTIAL FEATURES

National Emblem, Inc. Design # 108064

Description SF Cadet Rocker Patch

Accurate Size 1 ¼ x 4

Shape Rocker

FUFU Thread Colors / Type  546 GOLD (RAYON)

Twill Colors / Type  E936 BLACK 100% POLYESTER

Total Colors 1

Embroidery 35%

Border OVERLOCKED (546 GOLD)

Backing Thermo-Plastic

253

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE SHOES - HONOR GUARD

182 BATES Style 941 Men’s Oxford Hi-Gloss Black Leather

SPECIFICATIONS AND ESSENTIAL FEATURES FEATURES

 Formal high gloss oxford dress shoe featuring a long wearing Vibram® rubber outsole.  High gloss (Corofram) upper  Breathable lining  Cushioned removable insert  Long wearing Vibram® rubber outsole  Goodyear welt construction Made in the USA SIZES: D/E/EEE 6 -12,13,14,15

254

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE SHOES - HONOR GUARD

183 BATES Style 742 Womens Oxford Hi-Gloss Black Leather

SPECIFICATIONS AND ESSENTIAL FEATURES FEATURES

SIZES: D/E/EEE 6 -12,13,14,15

255

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

184 6” BASIC BLACK BOOT

(Mens Specs) ROCKY 2167

AlphaForce

SPECIFICATIONS AND ESSENTIAL FEATURES

FEATURES

These Boots are made with black full-grain leather and 1000-denier nylon fabric

These duty boots have been built with waterproof construction; this creates a barrier that is guaranteed to keep water out, so your feet will remain completely dry.

The Air-Port™ footbed is made from polyurethane and absorbs shock, but always reverts back to its earliest shape. The cushion footbed specifically targets your heel and metatarsal ridge, giving you support and comfort.

This boot features a non-metallic stabilizer, and has a non-marking RigiTrac™ outsole that provides oil and slip resistance. COLOR:

BLACK

REGULAR SIZES

Men's whole and half sizes, 3-16

Men's Widths: Medium, Wide

256

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

185 9” DUTY BOOTS ORIGINAL S.W.A.T. 1150 (Male TACT)

SPECIFICATIONS AND ESSENTIAL FEATURES FEATURES

Full grain leather / 1000 denier nylon upper with polishable heel and toe Foam padded collar and tongue for protection and increased breathability Gusseted tongue to keep dirt and debris out Durable brass alloy, rust proof hardware Moisture-wicking lining with AEGIS antimicrobial protection Removable custom fit EVA insole Custom-molded phylon EVA midsole for lightweight comfort and cradled support Stitched heel and toe for durability and increased service life Texon stability platform for lateral support and torsional rigidity Steel shank for superior support Custom-molded thermoplastic heel counter and toe box for instant comfort and lateral support Classic outsole: slip and oil resistant, non-marking rubber, exceeds the ASTM F489-96 test for slip resistance COLOR: BLACK REGULAR SIZES Men's whole and half sizes, 4 -16 Men's Widths: Regular, Wide

257

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

186 1152 9” SIDE ZIP BOOTS (Male TACT) ORIGINAL SWAT

SPECIFICATIONS AND ESSENTIAL FEATURES FEATURES

Full Grain and Split Leather Upper • 1000 Denier Nylon • Triple Stitched Upper • Full Length YKK Zipper with Velcro Closure • Steel Shank • Stitched Outsole • Carbon Rubber, Multi-Tred Traction, Self-Cleaning Outsole • Compression Molded EVA Midsole • Removable Molded Orthotic Innersole • Synthetic Moisture Wicking Lining • Waterproof and Insulated • Rust Proof Hardware • Weight - 39oz/pair (size 9) COLOR: BLACK

258

REGULAR SIZES  Regular Width (D) - 7 - 12, 13, 14, 15 Half Sizes through 12

DESCRIPTION MANUFACTURER MODEL # IMAGE ITEM #

187 9” SIDE ZIP BOOTS (Female TACT) ORIGINAL SWAT 1152F

259

FEATURES

 Full Grain and Split Leather Upper  1000 Denier Nylon  Triple Stitched Upper  Full Length YKK Zipper with Velcro Closure  Steel Shank  Stitched Outsole  Carbon Rubber, Multi-Tred Traction, Self-Cleaning Outsole  Compression Molded EVA Midsole  Removable Molded Orthotic Innersole  Synthetic Moisture Wicking Lining  Waterproof and Insulated  Rust Proof Hardware Weight - 39oz/pair (size 9) COLOR: BLACK REGULAR SIZES  Regular Sizes 6-11  Half Sizes through 12 Wide Width (EEE) 8 -12, 13, 14, 15

188 Danner Danner 8” Tachyon GTX Boot

260

SPECIFICATIONS AND ESSENTIAL FEATURES FEATURES

Waterproof, full-grain leather and 500 Denier nylon upper

Polishable toe

100% waterproof and breathable GORE-TEX liner

Speed lace fastening system

Danner Tachyon slip-resistant rubber outsole

COLOR: BLACK

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

189 Men's Black Leather Uniform Oxford BATES Style 968

SPECIFICATIONS AND ESSENTIAL FEATURES

261

FEATURES

 Easy to polish leather oxford featuring a long wearing Vibram® rubber outsole.  Leather upper  Breathable lining  Cushioned removable insert  Long wearing Vibram® rubber outsole  Goodyear welt construction Made in the USA SIZES D/E/EEE 6 -12,13,14,15

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Women's Uniform Oxford 769 190 BATES (Black Leather)

SPECIFICATIONS AND ESSENTIAL FEATURES FEATURES  Easy to polish leather oxford featuring a long wearing Vibram®® rubber outsole.  Leather upper  Breathable lining  Cushioned removable insert  Long wearing Vibram® rubber outsole  Goodyear welt construction Made in the USA

262

SIZES N 6-11, 12 M/W 4-11, 12 EW 6-11

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

191 Men’s Black Leather Padded Collar Chukka BATES SR78

SPECIFICATIONS AND ESSENTIAL FEATURES FEATURES

 Padded ankle collar.  Leather upper  Breathable lining  Cushioned removable insert  Non-marking Polyurethane Outsole  Long wearing Vibram® rubber outsole  Gooyear welt construction  Made in the USA

SIZES  Unisex sizing  Widths: C, D, E, EEE Sizes: 3 - 16

263

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

192 RIDING BOOTS, CALFSKIN DEHNER 190999CUSTOM

(MOTORCYCLE/MOUNTED)

SPECIFICATIONS AND ESSENTIAL FEATURES MOTORCYCLE BOOTS: (For Solo and Mounted Only)

 Boots: “Dehner” type “A” riding boots, imported French calfskin in black.  Black polished plain toe boot 17-18 inches  Tanned upper, medium round toe  Goodyear welt construction, combination last; nylon and dacron thread, double stitched  Full oil proof neoprene solo of not less than 18 iron  Full glove leather lined  Back upper seam double stitched with nylon thread  Individual sized throat  Full number one grade walking heel of neoprene  Boot calf section shall be cut and sewn so as to be worn with standard issues motorcycle breeches Each boot to be individually sized and fitted to assure a correct and personal fit.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

RIDING BOOTS 193 ALPINESTAR TECH 3 (HONDAS) (Black)

264

SPECIFICATIONS AND ESSENTIAL FEATURES MOTORCYCLE BOOTS: (For Hondas Only)

 Contoured shin plate protector is injected with high-modulus PU for a high level of impact and abrasion resistance.  Reinforced leather plate runs along rear of the boot.  Extended inside and outside plate guards the side and toe-box area of the boot.  Calf plate designed for maximum grip, support and side contact.  Internal plastic reinforcement on the inner side of the boot is covered by thick stamped suede for increased grip and heat resistance.  Instep flex-zone stitched for maximum support.  Action leather upper.  Alpinestars’ exclusive high grip rubber double density compound outsole with a contoured tempered steel shank over injected inside the assembly insole.  Four buckles with memory featuring a quick release/locking system.  High impact resistant buckles made from injected techno-polymer.  Top of the boot is sealed with a Velcro® strap connected to elastic stretch  Poly-fabric lining coupled with multi-density EVA.  Removable anatomic foot bed. Extended gaiter helps prevent water entry. SIZES Sizes: 5 – 16

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

RIDING BOOTS 194 SIDI CHARGER (HONDAS) (Black)

SPECIFICATIONS AND ESSENTIAL FEATURES

265

MOTORCYCLE BOOTS: (For Hondas Only)

Heel Detail: Three extended ribs are featured at the back of the boot. Rigid, shock resistant, anatomically shaped heel for maximum protection.

Non-Bootie Designs:

Single Flex System: Offers the rider free movement forward and backward while limiting its side to side deflection thus offering the rider maximum comfort and strength.

Buckles: Cam-lock buckle system. Strap memory retention system. Adjust the straps once and they will be at the same position for every ride after that! No more readjusting for every ride or mid-day during a ride.

Toe Areas: The tip of the toe are covered with plastic to protect the base material and seems against abrasion from brush etc. Plastic shift and brake lever guards on the top of each foot area.

Heat Shields: Each boot is equipped with an anti-heat undressed leather protection panel at the same height of most motorcycle’s exhaust heat shields.

Replaceable Parts: Every bolt on component is available separately. Riders can change the various components to replace items that have worn or have been damaged in a crash.

Composite Insole: Insole that is anatomically shaped to the rider. A cushioned liner is provided that can be removed if the rider desires a more roomy fit. No use of steel shanks riveted to its insole.

Lining: Cambrelle is a lining that, due to its particular polyimide structure, guarantees a rapid drying rate after the boot gets wet or sweaty. This prevents the onset of mold forming which extends the boots lifespan dramatically. The Teflon treated mesh panels in the rear calf area of the boot allow humidity to escape while the boot is in use.

266

SIZES Sizes: 5 – 15

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

195 BOOTS HAIX GSG9-S (Bomb Techs)

SPECIFICATIONS AND ESSENTIAL FEATURES

Product information:

• Color black • Inside CROSSTECH • Material waterproof leather • Sole DAVOS Sole • Leg height 8 inches

267

HAIX Secura Liner: Footwear inner liner which will never pull out or wrinkle up over time; lining is firmly secured and sealed along with the upper leather beneath the sole.

HAIX Sun Reflect Leather: Reduces the heating effect of the upper leather by direct sunlight. Sunlight is reflected by the leather, keeping the leather and the feet cooler.

HAIX MSL System: Stands for Micro Soft Light which is extremely lightweight foam injected into the sole to provide exceptional shock absorption and superior heat/cold insulation. Long lasting system has been proven to last the lifetime

Upper Material: A combination of waterproof leather, hydrophobic, breathable leather and flame retardant fabric

Moisture Barrier: CROSSTECH Footwear waterproof, breathable, bacteria and chemical resistant, bloodborne pathogen resistant

Fast Roping Properties: No seams on the inside lacing area of the shoe, abrasion-proof materials, padded ankle protection, and pronounced sole edge for superior braking features.

Closed two-zone lacing system: No risk of catching or trouser leg abrasion, twozone lacing can be separately and permanently fixed at different levels of tightness, flame retardant Nomex laces, hardware is nickel-free, rust-free, with no stud attachment through lining.

Protective Throughsole: Flexible Kevlar sole inlay, protection from nails

Sole: PU impact absorption wedge for good insulation against old, nonslip (even on cold or smooth surfaces), self-cleaning, non-marking, oil and fuel resistant, antistatic, allows quiet walking movements.

Insole: Anatomically shaped, removable insole with moisture transportation properties and good shock absorption.

268

SIZES  Widths: M, W Sizes: 5 - 16

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

196 BOOTS HAIX Airpower P7 High (Bomb Techs)

SPECIFICATIONS AND ESSENTIAL FEATURES

Product information "Airpower P7 High"

• Color black • Sole AIRPOWER P Sole • Inside GORE-TEX Performance • Material waterproof leather Leg height 9 inches

269

HAIX Secura Liner: Footwear inner liner which will never pull out or wrinkle up over time; lining is firmly secured and sealed along with the upper leather beneath the sole.

HAIX Sun Reflect Leather: Reduces the heating effect of the upper leather by direct sunlight. Sunlight is reflected by the leather, keeping the leather and the feet cooler.

HAIX Climate System: Permits air circulation with every step – moist air is released and fresh air comes in through the vent holes at the top of the boot.

HAIX AS System: Supports the arch of the foot in its natural, ideal position

Upper Material: Soft and supple waterproof leather, hydrophobic, breathable.

Moisture Barrier: GORE-TEX footwear, 4 layers with inner Cambrelle lining, abrasion resistant, softly padded with breathable foam. Waterproof, breathable, and chemical resistant.

Sole: Rubber compound outsole with PU wedge which is fuel, oil, and skid resistant, with a non-marking, self-cleaning, antistatic tread. Excellent insulation against heat and cold.

Insole: Anatomically formed, quick change, machine washable insert with excellent moisture absorption and quick drying qualities.

Footbed: Anatomically formed TEXON (fleece) absorbs moisture and supports ankle

Other: Anatomically formed and softly padded tongue, lightweight, high quality quick lacing eyelets, highly breathable nylon fabric, and reinforcement in the toe and heel area.

270

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

197 BOOTS HAIX AIRPOWER R2 (Bomb Techs)

SPECIFICATIONS AND ESSENTIAL FEATURES Product information "Airpower R2"

• Color black • Inside CROSSTECH • Classification ASTM F 2413-2011, CAN/CSA-Z195-2009, NFPA 1999-2013 • Sole AIRPOWER R Sole • Material waterproof leather Leg height 8 inches

HAIX Secura Liner: Footwear inner liner which will never pull out or wrinkle up over time; lining is firmly secured and sealed along with the upper leather beneath the sole.

HAIX Sun Reflect Leather: Reduces the heating effect of the upper leather by direct sunlight. Sunlight is reflected by the leather, keeping the leather and the feet cooler.

HAIX Climate System: Permits air circulation with every step – moist air is released and fresh air comes in through the vent holes at the top of the boot.

HAIX AS System: Supports the arch of the foot in its natural, ideal position

Upper Material: Soft and supple waterproof leather, hydrophobic, breathable.

271

Moisture Barrier: CROSSTECH footwear, 4 layers with inner Cambrelle lining, abrasion resistant, softly padded with breathable foam. Waterproof, breathable, bacteria and chemical resistant, bloodborne pathogen resistant.

Protective Toe Cap: Anatomically formed and well-padded steel protective toe cap to meet ASTM 2413-11 and CAN/CSA Z 195-2009 standard for personal protection – protective footwear.

Protective Flexible Midsole: Flexible protective stainless steel, cast into the sole, to meet ASTM F2413-11 and CAN/CSA Z195-2009 standard for personal protection – protective footwear

Sole: Newly developed extremely slip resistant rubber sole with PU wedge which is fuel, oil, and skid resistant, with a non-marking, self-cleaning, antistatic tread. Excellent insulation against heat and cold. Sole is heat resistant.

Insole: Anatomically formed, quick change, machine washable insert with excellent moisture absorption and quick drying qualities.

Footbed: Anatomically formed TEXON (fleece) absorbs moisture and supports ankle

Other: Anatomically formed and softly padded tongue, integrated heel bend, raised tip, Patented HAIX Lacing System: combined lacing and zipper unit, reflective zone in the heel and instep bend.

272

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

198 BOOTS HAIX Black Eagle Tactical (Bomb Techs) 20 Mid

SPECIFICATIONS AND ESSENTIAL FEATURES Product information "Black Eagle Tactical 20 Mid"

• Color black • Inside GORE-TEX • Sole BLACK EAGLE 01 Sole • Material waterproof leather Leg height 6 inches

Inner Lining: GORE-TEX Extended; 3-layer GORE-TEX laminate, waterproof and highly breathable. Abrasion-resistant lining with optimized- climate comfort, especially for flexible alternating inside and outside use.

HAIX Climate System: Climate System with Micro-Dry lining at top of leg

Insert: Comfortable, cushioning, moisture wicking, anti-bacterial. Separate heel shape for good cushioning and foot insertion. “AIRFLOW” channels

Running sole: made of rubber, resistant to oil and gasoline, non-marking

Anti Slip: Very good grip on different terrains by profile configuration and use of a special rubber

273

Durable Sole: Rubber mixture for long durability

Double Hole Frame/Stone Shield: Stabilizes the shoe and guides the foot during unwinding movements, prevents uneven surfaces from pressing through to the foot

Inner sole: Made of different EVA/TPU materials, light, cushioning, supporting

Absorb: Permanent cushioning in heel area by special EVA material in the inner sole

Energy Return/Supination Support: Inner sole in the front part of the foot made of a strong spring-back material for effective use of energy

Pronation Support: Supports the center of the heel, prevents overpronation (arch collapsing inward) by using a harder EVA material

Stabilizer: Asymmetrical TPU for stabilizing the heel

Others: Low weight, antistatic, metal-free

Sun Reflect: Reduces the heating effect of the upper leather by direct sunlight. Sunlight is reflected by the leather, keeping the leather and the feet cooler.

274

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

199 BOOTS HAIX Mission Black (Bomb Techs)

SPECIFICATIONS AND ESSENTIAL FEATURES

Product information "Mission Black"

• Color black • Material leather/textile • Inside GORE-TEX • Leg height 7 inches Sole VIBRAM 016 Sole

Upper Material Leather/Textile combination, hydrophobic, breathable, 2.0 – 2.2 mm thick.

Inner Lining GORE-TEX® Extended; 3-layer GORE-TEX® laminate, waterproof and breathable. Highly abrasion-resistant lining with fleece midlayer. Optimized- climate comfort for all year seasons and excessive use.

Insole Dimensionally stable, torsion-proof, prevents penetration pressure from sharp objects (e.g. stones)

Foot bed Comfortable, cushioning, moisture repellent, anti-bacterial. Separate heel shape for good cushioning and foot insertion.

Sole Rubber/PU walking sole with proven street/ terrain tread, wear resistant and non-slip traction; large, bevelled contact surface and superior bending comfort. Oil and gasoline

275

resistance and non-marking characteristics. Heat resistant.

HAIX® Climate System Climate System with Micro-Dry lining at the top of the boot leg.

HAIX® 2-Zone Lacing Two Zone Lacing System enables a seperate adjustment of the boot to the foot and leg area.

HAIX® Smart Lacing Smooth and non-pressure adjustment of the boot to the foot, Quick lock and lace pocket.

Others Lacing system with eyelets permitting smooth movement, pulling strap, lace pocket, manually applied rubber sidewall on the front and back of the shoe for a better durability, antistatic.

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

200 Nike 329798 Nike Special Field Boot

SPECIFICATIONS AND ESSENTIAL FEATURES

276

FEATURES

 Quick-drying synthetic leather overlays for durability and support  Multiple ventilation zones that allow the boot to breathe and drain quickly  Genuine leather footbed for durability, flexibility and comfort

COLOR: BLACK REGULAR SIZES Men's whole and half sizes, 4-12 ½, 13, 14, 15

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

201 8” Zipper waterproof boot 5.11 Galls SP725/MFG 12004

SPECIFICATIONS AND ESSENTIAL FEATURES

277

FEATURES

 Full-grain leather  Antibacterial and moisture-wicking lining  Waterproof, breathable and BBP-resistant  Oil- and slip-resistant outsole  Non-metallic shank  Semi-rigid heel and toe reinforcement

Side zip

COLOR:

BLACK

REGULAR SIZES

 Regular Width whole sizes 4-15, Half Sizes 6 ½ - 11 ½

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Marine Unit Waterproof boot Danner Acadia 8” Black boot

202 Style 21210

http://www.danner.co

m/acadia-8-black.html

278

SPECIFICATIONS AND ESSENTIAL FEATURES

FEATURES

 100% waterproof and breathable liner  Full grain leather for durability and polishing purposes  1000 Denier nylon upper, abrasion/tear/scuff-resistant, quick-drying  Lace-to-toe for secure fit

Vibram Kletterlift outsole for traction and stability on both wet and dry surfaces

COLOR:

BLACK

REGULAR SIZES

Men’s whole sizes 7-16, half sizes 7.5-11.5

Women’s whole sizes 5-10, half sizes 5.5-9.5

279

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Marine Unit Waterproof boot Danner Rivot TFX 8” Black GTX boot

203 Style 51520

http://www.danner.co

m/rivot-tfx-8-black- gtx.html

SPECIFICATIONS AND ESSENTIAL FEATURES

FEATURES

 Full grain leather and 1000D nylon upper  100% waterproof and breathable liner

Vibram Rivot TFX outsole for traction

COLOR:

BLACK

REGULAR SIZES

Men’s whole sizes 6-16, half sizes 6.5-11.5

280

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

Style #28010

204 Marine Unit Waterproof boot Danner 8In Kinetic http://www.galls.com /danner-8-kinetic-

gore-tex-waterproof- boot?PMSRCH=fw290

SPECIFICATIONS AND ESSENTIAL FEATURES

FEATURES

 100% waterproof and breathable liner  8” height

Low lug outsole for superior surface contact and traction

COLOR:

BLACK

REGULAR SIZES

Men’s whole sizes 6-15, half sizes 6.5-11.5

281

ITEM # DESCRIPTION MANUFACTURER MODEL # IMAGE

205 9” DUTY BOOTS

(Female Airport PSA) ORIGINAL S.W.A.T. 115011

SPECIFICATIONS AND ESSENTIAL FEATURES

COLOR:

BLACK

REGULAR SIZES

Women’s whole sizes 5-11, half sizes 5 ½-10 ½

282