<<

TECHNICAL DATA SHEET KILZ Concrete & Masonry KILZ Concrete & Masonry Paint Stripper is a biodegradable stripper for use on interior and exterior vertical and horizontal surfaces. It removes multiple layers of stains, FLOOR COATINGS , urethanes, elastomerics, and sealants from surfaces.

CONCRETE & MASONRY WHERE TO USE PAINT STRIPPER Recommended for interior and exterior, horizontal and vertical concrete, masonry, stone, brick and metal surfaces such as: AS OF 3/22/2011 COMPLIES OR IS CERTIFIED WITH: OTC Yes CARB Yes • Garage Floors • Patios • Basement Floors SCAQMD Yes • Driveways • Pool Deck • Concrete Walls. • Walkways DO NOT USE ON MARBLE, GRANITE, TERRAZZO, COLOURED CONCRETE, BRASS, BRONZE or COPPER.

PRODUCT APPLICATION • The stripped surface must be rinsed with No. L0505C • Use product when air and surface temperatures water thoroughly to remove all chemical 3.79 L are between 10-32° C. residues before recoating. • Wear protective clothing, goggles, acid • Spread rate is approximately 5.6 – 7 m² COMPOSITION resistant gloves, and a NIOSH approved air (60-75 sq. ft.) per 3.79 L. Active: Glycolic Acid purifying respirator with an organic vapor CAUTION: Surfaces may become slippery Weight per 3.79 L (kg): 3.86 +/- 0.09 cartridge. Volume : 7.4% +/- 2% when wet. Use caution when walking on • Apply a thick, even layer of stripper onto the surface when moisture is present. Weight Solids: 8.9% +/- 2% surface using a or an airless : 95-100 KU sprayer. Stripper thickness should be such that DRY TIME VOC (C.O.V.): 40.6 wt % the original coated surface is completely covered. • Make sure concrete or surface is visually FLASHPOINT • Most coatings will take between 1 – 6 hours to and completely dry to touch prior to N/A lift. Penetration varies according to recoating. Surface dry time will vary, type, thickness and temperature. COATING depending on air & surface temperature. SURFACE PREPARATION WILL WRINKLE WHEN THE JOB IS DONE. • SHAKE WELL PRIOR TO USE. Pour the KILZ • To ensure that the coating is completely Concrete & Masonry Paint Stripper into a covered with the stripper, check the area paint tray or bucket. If water appears to have periodically. If the coated surface becomes separated out, stir product until uniform. Do visible again, re-apply a light coating. not dilute. • If hot or windy conditions cause drying, • For vertical and glossy or greasy surfaces, re-apply a light coating. The stripper should scuff the surface lightly with a medium remain wet and active until the coating grit sand paper prior to application to wrinkles. prevent sagging of paint stripper. • Remove all coating and residues with a • Product should be tested in an inconspicu- scraper, stiff brush, squeegee or pressure ous area to estimate required lift time and washer. ensure acceptable performance. • The stripper is formulated to remove several • Protect grass and any nearby plants by layers of coating in one application. Some dampening these areas with water and areas however, may require an additional covering with plastic drop cloths. application to remove all layers. • Prevent all rinse solution from entering storm drains.

®

©2013 Masterchem Industries LLC, 3135 Old Hwy M, Imperial, MO 63052-2834 This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, fitness for a particular purpose 1-866-977-3711 • www.kilz.com or of any other nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative, call 1-866-977-3711. 1 of 2 TECHNICAL DATA SHEET KILZ Concrete & Masonry Paint Stripper

FLOOR COATINGS

CONCRETE & MASONRY PAINT STRIPPER

CLEAN UP & DISPOSAL • If product comes in contact with painted or finished surfaces not intended for removal, rinse immediately with fresh water. • Thoroughly rinse all surfaces, clothing and with fresh water immediately after use. • Collect lifted coating and dispose of it in accordance with current governmental regulations. • Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service. CAUTIONS / LIMITATIONS • Protect from freezing. • DO NOT USE ON MARBLE, GRANITE, TERRAZZO, COLOURED CONCRETE, BRASS, BRONZE or COPPER. • For best results, apply at temperatures between 10° C - 32° C. Temperatures above 32° C may affect the application such as drying too fast. Avoid in direct sun. NOTE: If the surface is hot to the touch it should be considered too hot to apply this coating. • CAUTION: Surfaces may become slippery when wet. Use caution when walking on surface when moisture is present. • Shelf life under normal conditions is two years unopened. GENERAL INFORMATION KEEP FROM FREEZING / READ ALL DIRECTIONS BEFORE OPENING CONTAINER WARNING! If you scrape, sand or remove old paint, you may release dust. LEAD IS TOXIC. Contact the National Lead Information Hotline at 1-800- 424-LEAD or log on to www.epa.gov/lead. WARNING! Sanding or scraping pressure treated may be hazardous; wear appropriate protection.

FUMES MAY BE HARMFUL. MAY IRRITATE EYES. Do not breathe fumes. Avoid Contact with eyes. Use only with adequate ventilation. Wear eye protec- tion, respirator and protective clothing while handling this product. Keep out of reach of children.

FIRST AID • Contains POLYOXPROPYLENE, GLYCOLIC ACID, HYDROGEN PEROXIDE. If swallowed, call a Poison Control Centre or doctor immediately. • If inhaled, move person to fresh air. • If in eyes rinse with water for 15 -20 minutes. • Eye and skin contact: In case of eye or skin contact, flush immediately with water for 20 minutes. Get medical attention if irritation or symptoms of overexposure persist. • If inhaled, move to fresh air. • If swallowed, DO NOT induce vomiting. Get medical attention immediately. Give water to dilute material in stomach. Never give anything by mouth to an unconscious person.

CAUTION: KEEP OUT OF REACH OF CHILDREN DO NOT TAKE INTERNALLY.

®

©2013 Masterchem Industries LLC, 3135 Old Hwy M, Imperial, MO 63052-2834 This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, fitness for a particular purpose 1-866-977-3711 • www.kilz.com or of any other nature are made with respect to this information or to any product referred to in this information. For MSDS or to consult with a technical service representative, call 1-866-977-3711. 2 of 2