The Radio Amateur's Hand Book
Total Page:16
File Type:pdf, Size:1020Kb
Load more
Recommended publications
-
Army Radio Communication in the Great War Keith R Thrower, OBE
Army radio communication in the Great War Keith R Thrower, OBE Introduction Prior to the outbreak of WW1 in August 1914 many of the techniques to be used in later years for radio communications had already been invented, although most were still at an early stage of practical application. Radio transmitters at that time were predominantly using spark discharge from a high voltage induction coil, which created a series of damped oscillations in an associated tuned circuit at the rate of the spark discharge. The transmitted signal was noisy and rich in harmonics and spread widely over the radio spectrum. The ideal transmission was a continuous wave (CW) and there were three methods for producing this: 1. From an HF alternator, the practical design of which was made by the US General Electric engineer Ernst Alexanderson, initially based on a specification by Reginald Fessenden. These alternators were primarily intended for high-power, long-wave transmission and not suitable for use on the battlefield. 2. Arc generator, the practical form of which was invented by Valdemar Poulsen in 1902. Again the transmitters were high power and not suitable for battlefield use. 3. Valve oscillator, which was invented by the German engineer, Alexander Meissner, and patented in April 1913. Several important circuits using valves had been produced by 1914. These include: (a) the heterodyne, an oscillator circuit used to mix with an incoming continuous wave signal and beat it down to an audible note; (b) the detector, to extract the audio signal from the high frequency carrier; (c) the amplifier, both for the incoming high frequency signal and the detected audio or the beat signal from the heterodyne receiver; (d) regenerative feedback from the output of the detector or RF amplifier to its input, which had the effect of sharpening the tuning and increasing the amplification. -
Detailed Investigation of the Electric Discharge Plasma Between Copper Electrodes Immersed Into Water
atoms Article Detailed Investigation of the Electric Discharge Plasma between Copper Electrodes Immersed into Water Roman Venger 1, Tetiana Tmenova 1,2,*, Flavien Valensi 2, Anatoly Veklich 1, Yann Cressault 2 and Viacheslav Boretskij 1 1 Electronics and Computer Systems, Faculty of Radio Physics, Taras Shevchenko National University of Kyiv, 64, Volodymyrska St., 01601 Kyiv, Ukraine; [email protected] (R.V.); [email protected] (A.V.); [email protected] (V.B.) 2 Université de Toulouse, UPS, INPT; LAPLACE (Laboratoire Plasma et Conversion d’Energie), 118 route de Narbonne, F-31062 Toulouse CEDEX 9, France; [email protected] (F.V.); [email protected] (Y.C.) * Correspondence: [email protected]; Tel.: +38-063-598-5219 Academic Editors: Milan S. Dimitrijevi´cand Luka C.ˇ Popovi´c Received: 11 September 2017; Accepted: 16 October 2017; Published: 23 October 2017 Abstract: A phenomenological picture of pulsed electrical discharge in water is produced by combining electrical, spectroscopic, and imaging methods. The discharge is generated by applying ~350 µs long 100 to 220 V pulses (values of current from 400 to 1000 A, respectively) between the point-to-point copper electrodes submerged into the non-purified tap water. Plasma channel and gas bubble occur between the tips of the electrodes, which are initially in contact with each other. The study includes detailed experimental investigation of plasma parameters of such discharge using the correlation between time-resolved high-speed imaging, electrical characteristics, and optical emission spectroscopic data. Radial distributions of the electron density of plasma is estimated from the analysis of profiles and widths of registered Hα and Hβ hydrogen lines, and Cu I 515.3 nm line, exposed to the Stark mechanism of spectral lines’ broadening. -
Research Paper Commerce Physics Atomic Emission Spectroscopy
Volume-4, Issue-10, Oct-2015 • ISSN No 2277 - 8160 Commerce Research Paper Physics Atomic Emission Spectroscopy Ramanjeet Kaur Assistant Professor Physics Department, R S D College, Ferozepur City ABSTRACT The atomic emission spectroscopy is method based on the study of light emitted by atoms to determine the proportional quantity of a particular element in a given sample. Three techniques of atomic emission spectroscopy flame emission arc & spark emission and plasma atomic emission spectroscopy, their working, Principle and applications has been discussed in detail. KEYWORDS : -spectroscopy, flame, spark & arc, plasma, qualitative & quantitative analysis INTRODUCTION Atomic spectroscopy is the determination of elemental composition termining the accuracy of the analysis. The most popular sampling by its electromagnetic spectrum. Electrons exist in energy levels with- method is nebulization of a liquid sample to provide a steady flow of in an atom. These levels have well defined energies and electrons aerosol into a flame. An introduction system for liquid samples con- moving between them must absorb or emit energy equal to the dif- sists of three components: (a) a nebulizer that breaks up the liquid ference between them. The wavelength of the emitted radiant ener- into small’ droplets, (b) an aerosol modifier that removes large drop- gy is directly related to the electronic transition which has occurred. lets from the stream, allowing only droplets smaller than a certain Since every element has a unique electronic structure, the wave- size to pass, and (c) the flame or atomizer that converts the anaIyte length of light emitted is a unique property of each individual ele- into free atoms. -
HP 423A Crystal Detector
Errata Title & Document Type: 423A and 8470A Crystal Detector Operating and Service Manual Manual Part Number: 00423-90001 Revision Date: July 1976 About this Manual We’ve added this manual to the Agilent website in an effort to help you support your product. This manual provides the best information we could find. It may be incomplete or contain dated information, and the scan quality may not be ideal. If we find a better copy in the future, we will add it to the Agilent website. HP References in this Manual This manual may contain references to HP or Hewlett-Packard. Please note that Hewlett- Packard's former test and measurement, life sciences, and chemical analysis businesses are now part of Agilent Technologies. The HP XXXX referred to in this document is now the Agilent XXXX. For example, model number HP8648A is now model number Agilent 8648A. We have made no changes to this manual copy. Support for Your Product Agilent no longer sells or supports this product. You will find any other available product information on the Agilent Test & Measurement website: www.agilent.com Search for the model number of this product, and the resulting product page will guide you to any available information. Our service centers may be able to perform calibration if no repair parts are needed, but no other support from Agilent is available. OPERATING AND SERVICE MANUAL - I 423A 8470A CRYSTAL DETECTOR HEWLETT~PACKARD Plint.d: JUtY 191& e H.",len Packard Co. \910 1 " • .' • I .... ,. ", - \, . '. ~ ~.. ". ." , .' " . ..... " 'I. "",:,. • ' Page 2 i\lodel ·123A/8470A 1. GENERAL INFORMATION 10. -
Electrical Engineering
SCIENCE MUSEUM SOUTH KENSINGTON HANDBOOK OF THE COLLECTIONS ILLUSTRATING ELECTRICAL ENGINEERING II. RADIO COMMUNICATION By W. T. O'DEA, B.Sc., A.M.I.E.E. Part I.-History and Development Crown Copyright Reseruea LONDON PUBLISHED BY HIS MAJESTY's STATIONERY OFFICI To be purchued directly from H.M. STATIONERY OFFICI at the following addre:11ea Adutral Houae, Kinpway, London, W.C.z; no, George Street, Edinburgh:& York Street, Manchester 1 ; 1, St, Andrew'• Cretccnr, Cudi.lf So, Chichester Street, Belfa1t or through any Booueller 1934 Price 2s. 6d. net CONTENTS PAGB PREFACE 5 ELECTROMAGNETI<: WAVF13 7 DETECTORS - I I EARLY WIRELESS TELEGRAPHY EXPERIMENTS 17 THE DEVELOPMENT OF WIRELESS TELEGRAPHY - 23 THE THERMIONIC vALVE 38 FuRTHER DEVELOPMENTS IN TRANSMISSION 5 I WIRELESS TELEPHONY REcEIVERS 66 TELEVISION (and Picture Telegraphy) 77 MISCELLANEOUS DEVELOPMENTS (Microphones, Loudspeakers, Measure- ment of Wavelength) 83 REFERENCES - 92 INDEX - 93 LIST OF ILLUSTRATIONS FACING PAGE Fig. I. Brookman's Park twin broadcast transmitters -Frontispiece Fig. 2. Hughes' clockwork transmitter and detector, 1878 8 Fig. 3· Original Hertz Apparatus - Fig. 4· Original Hertz Apparatus - Fig. S· Original Hertz Apparatus - 9 Fig. 6. Oscillators and resonators, 1894- 12 Fig. 7· Lodge coherers, 1889-94 - Fig. 8. Magnetic detectors, 1897, 1902 - Fig. 9· Pedersen tikker, 1901 I3 Fig. IO. Original Fleming diode valves, 1904 - Fig. II. Audion, Lieben-Reisz relay, Pliotron - Fig. IZ. Marconi transmitter and receiver, 1896 Fig. IJ. Lodge-Muirhead and Marconi receivers 17 Fig. 14. Marconi's first tuned transmitter, 1899 Fig. IS. 11 Tune A" coil set, 1900 - 20 Fig. 16. Marconi at Signal Hill, Newfoundland, 1901 Fig. -
Crystal Receivers for Broadcast Reception
CRYSTAL RECEIVERS FOR BROADCAST RECEPTION BY PERCY W. HARRIS AUTH OR OF "THE A B C OF WIRELE SS " R E-C EI\·I~ G A \':I R EL l':': SS C c:' .''':CERT \\Tf1r :\ HO]\IE-l\[.-\DE C RYSTAL \;ECEI\ -EI~ LONDON THE WIRELESS PRESS, LTD. t 2 & I3, HENRIETTA STREET, w.e. 2 A HOME- MADE C R Y ST AL RECEIVER WITH ADJUSTME NTS F OR B R OADCAST 'NAVE-LE N GTHS A N D E I F F EL T OW E R TIME SI GN ALS. I N ST R UCTIONS FOR BUILDING T H I S S E T ARE G IVEN IN CHAP T E R X , CRYSTAL RECEIVERS FOR BROADCAST RECEPTION BY PERCY \Y HARIUS A UTHOR OF "THE A 13 C OF W I R ELESS," ETC. LOND ON THE WIRELESS PRESS, LTD. 1 2 & 13, HENRIETTA STREET, W.c. 2 NEW YORK: ,\VIlmLESS PRESS INC., 326 BIWADWAY THE WIRELESS PRESS, LTD. FOREIGN AND CO LOAIAL AGEiVCIES: SYDNEY, N.S.vV.: 97, Clarence Street. MELBOURNE: 422 (4, Little CoUins Street. MADRID: La Prensa Radiotelegrafica, 43, Calle de Alcala. GENOA: Agenzia Radiotelegrafica Italiana, Via Varese 3. AMSTERDAM: Nederlandsch Persbureau Radio, 562, Keizersgracht. INTRODUCTION THE advent of broadcast radio-telephony has aroused con siderable interest in the simple forms of wireless receiver, with the result that the crystal detector, \vhich was fast being ousted by the thermionic valve, has once again become popular. Numerous crystal receivers are now on the market, and the beginner in wireless may well feel some con fusion as to their merits. -
Identification of the Electric Spark Electromagnetic Waveform Based on SVM
Advances in Engineering Research, volume 127 3rd International Conference on Electrical, Automation and Mechanical Engineering (EAME 2018) Identification of the Electric Spark Electromagnetic Waveform Based on SVM Tongtong Li1,*, Ziyuan Tong2, Shoufeng Tang1, Xia Qin1, Mingming Tong1 and Zhaoliang Xu3 1China University of Mining and Technology, China 2School of Electrical Engineering and Telecommunications, The University of New South Wales, Australia 3Xuzhou Hanlin Technology Co., Ltd., China *Corresponding author Abstract—Electromagnetic wave of electrical spark is a current. potential cause to eletrical equipment failure. This research focused on identificating and comparative analyzing the different A. Electromagnetic Characteristics Extraction of the Electric types of electromagnetic waveform generated by eletrical Spark equipment failure based on SVM. After analyzing and extracting the features the electromagnetic waveform, a model was built to First, confirm that you have the correct template for your identificate the type of the elctromagnetic waveform. The paper size. This template has been tailored for output on the collected standard electromagnetic waveforms were used as the US-letter paper size. If you are using A4-sized paper, please imput of the train model and the model accuracy was improved close this file and download the file for “MSW_A4_format”. by adjusting training parameters afer analyzing the results, When the distance between the contact closure electrodes When inputting an unknown type of electromagnetic waveform, gradually decreases or a strong electric field occurs[6], the SVM may predict the output of the network according to the current density gradually increases and produces high recognition rule. Then the types of electromagnetic waveforms temperature ionization, then contact and electrode gas will be were identificated by using adjusted models. -
Galvanic Isolation System with Wireless Power Transfer for Multiple Gate Driver Supplies of a Medium-Voltage Inverter Paper
電気学会論文誌●(●●●●●●●部門誌) IEEJ Transactions on ●●●●●●●●●●●●●●● Vol.●● No.● pp.●-● DOI: ●.●●/ieejeiss.●●.● Paper Galvanic Isolation System with Wireless Power Transfer for Multiple Gate Driver Supplies of a Medium-voltage Inverter * * * Keisuke Kusaka , Student member, Koji Orikawa, Member , Jun-ichi Itoh, Member a) ** ** ** Isamu Hasegawa , Non-member, Kazunori Morita , Member, Takeshi Kondo , Non-member (Manuscript received Jan. 00, 20XX, revised May 00, 20XX) In this paper, a gate driver supply, which supplies power to multiple gate drivers, is demonstrated. Robust isolation is required in the gate drive supplies of a medium-voltage inverter in order to drive high-voltage switching devices such as insulated-gate bipolar transistors. The proposed isolation system achieves isolation with transmission coils mounted on printed circuit boards. Furthermore, the isolation system transmits power from one transmitting board to six receiving boards. In the conventional system, the number of receivers is limited to one. In contrast, multiple receivers are acceptable in the proposed system. These characteristics help reduce the of the isolation system for the gate driver supplies. This paper presents the fundamental characteristics of the isolation system. The equivalent circuit of the proposed system can be derived by applying the equivalent circuit of a wireless power transfer system with a repeater coil. In addtion, a design method for the resonance capacitors is mathematically introduced using the equivalent circuit. It is verified that an isolation system with multiple receivers can be designed using the same resonance conditions as an isolation system with a single receiver. Moreover, the isolation system is experimentally demonstrated. It is confirmed that the isolation system transmits power with a maximum efficiency of 46.9% at an output power of 16.6 W beyond an air gap of 50 mm with only printed circuit boards. -
The Gulf of Georgia Submarine Telephone Cable
.4 paper presented at the 285th Meeting of the American Institute of Electrical Engineers, Vancouver, B. C., September 10, 1913. Copyright 1913. By A.I.EE. THE GULF OF GEORGIA SUBMARINE TELEPHONE CABLE BY E. P. LA BELLE AND L. P. CRIM The recent laying of a continuously loaded submarine tele- phone cable, across the Gulf of Georgia, between Point Grey, near Vancouver, and Nanaimo, on Vancouver Island, in British Columbia, is of interest as it is the only cable of its type in use outside of Europe. The purpose of this cable was to provide such telephonic facilities to Vancouver Island that the speaking range could be extended from any point on the Island to Vancouver, and other principal towns on the mainland in the territory served by the British Columbia Telephone Company. The only means of telephonic communication between Van- couver and Victoria, prior to the laying of this cable, was through a submarine cable between Bellingham and Victoria, laid in 1904. This cable was non-loaded, of the four-core type, with gutta-percha insulation, and to the writer's best knowledge, is the only cable of this type in use in North America. This cable is in five pieces crossing the various channels between Belling- ham and Victoria. A total of 14.2 nautical miles (16.37 miles, 26.3 km.) of this cable is in use. The conductors are stranded and weigh 180 lb. per nautical mile (44. 3 kg. per km.). By means of a circuit which could be provided through this cable by way of Bellingham, a fairly satisfactory service was maintained between Vancouver and Victoria, the circuit equating to about 26 miles (41.8 km.) of standard cable. -
History of Diode
HISTORY OF DIODE In electronics, a diode is a two-terminal electronic component that conducts electric current in only one direction. The term usually refers to a semiconductor diode, the most common type today, which is a crystal of semiconductor connected to two electrical terminals, a P-N junction. A vacuum tube diode, now little used, is a vacuum tube with two electrodes; a plate and a cathode. The most common function of a diode is to allow an electric current in one direction (called the diode's forward direction) while blocking current in the opposite direction (the reverse direction). Thus, the diode can be thought of as an electronic version of a check valve. This unidirectional behavior is called rectification, and is used to convert alternating current to direct current, and extract modulation from radio signals in radio receivers. However, diodes can have more complicated behavior than this simple on-off action, due to their complex non-linear electrical characteristics, which can be tailored by varying the construction of their P-N junction. These are exploited in special purpose diodes that perform many different functions. Diodes are used to regulate voltage (Zener diodes), electronically tune radio and TV receivers (varactor diodes), generate radio frequency oscillations (tunnel diodes), and produce light (light emitting diodes). Diodes were the first semiconductor electronic devices. The discovery of crystals' rectifying abilities was made by German physicist Ferdinand Braun in 1874. The first semiconductor diodes, called cat's whisker diodes were made of crystals of minerals such as galena. Today most diodes are made of silicon, but other semiconductors such as germanium are sometimes used. -
Radio Digest, 1924-1925
B64714 6 DEC 271924 Aerial Aids for Christmas Set Buyers—J. E. Owen; New Het-duo-gen Circuit; "X" Wire—Key to Neutrodyne Success ; Details of $1,000.00 Gold Award Set Radio Di EVERY m= PROGRAMS TEN I CENTS REG. U. S. PAT. OFF. & DOM. OF CANADA \/,J YT Copyright 1924 VOl. -A.1 By Radio Digest Publishing Co. SATURDAY, DECEMBER 27, 1924 No. 12 NEW SET—FIND OF YEAR HET-DUO-GEN TUNES EITHER COAST EASILY Selectivity C. E. Brush Uses Six Tubes in Decidedly New Hook-Up —Tells How to Build Meet the Het-duo-gen! The set that really brings in what you want when you want it has come to light at last. A complete surprise be- cause its development is so different from the lines along which most ex- perimenters were known to be working. Combining the advantages of the hetero- dyne with regeneration on two tubes, C. E. Brush, of Chicago, has achieved a degree of selectivity that is almost miraculous. The sensitivity seems con- sistently to equal that of an eight tube PHONE CONNECTION super-heterodyne while the volume from three stages of audio frequency ampli- fication is more than enough for dancing. LONDON -NEW YORK A large loud speaker is required to handle it. Once the circuit is explained and the NEW STATION READY FOR operation understood, it all seems so simple that one wonders why it hasn't SERVICE NEXT YEAR been done before. Cost? The cost to (Continued on page 2) Will Use 4,000,000 Watts Power for Transoceanic Talking—Toll Charge Approximately $25 LONDON, Eng.—It is not only possible, but absolutely certain that in a year's time, any man in England can pick up the ordinary telephone in his house and speak to a friend in New York. -
Plasma Discharge in Water and Its Application for Industrial Cooling Water Treatment
Plasma Discharge in Water and Its Application for Industrial Cooling Water Treatment A Thesis Submitted to the Faculty of Drexel University by Yong Yang In partial fulfillment of the Requirements for the degree of Doctor of Philosophy June 2011 ii © Copyright 2008 Yong Yang. All Rights Reserved. iii Acknowledgements I would like to express my greatest gratitude to both my advisers Prof. Young I. Cho and Prof. Alexander Fridman. Their help, support and guidance were appreciated throughout my graduate studies. Their experience and expertise made my five year at Drexel successful and enjoyable. I would like to convey my deep appreciation to the most dedicated Dr. Alexander Gutsol and Dr. Andrey Starikovskiy, with whom I had pleasure to work with on all these projects. I feel thankful for allowing me to walk into their office any time, even during their busiest hours, and I’m always amazed at the width and depth of their knowledge in plasma physics. Also I would like to thank Profs. Ying Sun, Gary Friedman, and Alexander Rabinovich for their valuable advice on this thesis as committee members. I am thankful for the financial support that I received during my graduate study, especially from the DOE grants DE-FC26-06NT42724 and DE-NT0005308, the Drexel Dean’s Fellowship, George Hill Fellowship, and the support from the Department of Mechanical Engineering and Mechanics. I would like to thank the friendship and help from the friends and colleagues at Drexel Plasma Institute over the years. Special thanks to Hyoungsup Kim and Jin Mu Jung. Without their help I would not be able to finish the fouling experiments alone.